Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “metallic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Metal-metal reinforced laminar composites

Two prototype laminar composites have shown potential for high strength and high temperature applications. These composites might be made with less in-place anisotropy and be less expensive than comparable fiber composites.

Weeton, J. W.↗
NASA NTRS1973

Plasma-sprayed metal-glass and metal-glass fluoride coatings for lubrication to 900 C

Plasma-sprayed composites, which have good oxidation-resistance and self-lubricating characteritics to 900 C, were developed. The composites are a nichrome matrix containing dispersed glass for oxidation protection and calcium fluoride for lubrication; they are applied to bearing surfaces by plasma spraying layers about 0.050 centimeters thick which are then machined to 0.025 centimeters. Oscillating bearing tests were performed in air to 900 C at unit radial loads up to 3.5 x 10 to the 7th power N/sq M (5000 psi) and a thrust load of 1960N (440 lbs). Bearings with a composite liner in the bore were in good condition after over 50,000 oscillating cycles accumulated during repeated, bearing temperatures cycles between 25 and 900 C.

Sliney, H. E.↗
NASA NTRS1972

Metal-metal laminar composites for high-temperature applications.

The potentialities of composites consisting of multiple layers of tungsten alternated by layers of Nichrome V (a ductile, weaker than tungsten, but oxidation resistant alloy) at temperatures on the order of 2000 F are studied experimentally. The highest tensile strengths obtained for the composites were 600 MN/sq m (87,000 psi) at 1600 F and 448 MN/sq m (65,000 psi) at 2000 F. Highest 100-hr stress-rupture strengths at these temperatures were 387 MN/sq m (56,000 psi) and 121 MN/sq m (17,500 psi), respectively.

Hoffman, C. A.↗
NASA NTRS1974

Plasma-sprayed metal-glass and metal-glass fluoride coatings for lubrication to 900 C

Plasma-sprayed composites, which have good oxidation resistance and self-lubricating characteristics to 900 C, were developed. The composites are a nichrome matrix containing dispersed glass for oxidation protection and calcium fluoride for lubrication; they are applied to bearing surfaces by plasma spraying layers about 0.050 cm thick which are then machined to 0.025 cm. Oscillating bearing tests were performed in air to 900 C at unit radial loads up to 5000 psi and a thrust load of 440 lb. Bearings with a composite liner in the bore were in good condition after over 50,000 oscillating cycles accumulated during repeated bearing temperature cycles between 25 and 900 C.

Sliney, H. E.↗
NASA NTRS1975

Metal-to-metal charge transfer transitions - Interpretation of visible-region spectra of the moon and lunar materials

Prominent bands in the spectral profiles of Fe-Ti phases in lunar samples have been attributed to charge-transfer transitions between Fe and Ti cations, and a model is presented for calculating charge transfer energies from energy levels computed by the SCF-X(alpha) scattered wave molecular orbital method for isolated MO6 octahedral coordination clusters containing Fe(2+), Fe(3+), Ti(3+), and Ti(4+) cations. The calculated charge transfer energy for the Fe(2+) to Ti(4+) transition correlates well with a measured spectral feature around 0.6 micron in ilmenite, and, since ilmenite is a major constituent of mare basalts and dark-mantling material, the observed darkness and blueness of the regolith in lunar black spots is attributed primarily to this transition. The Ti(3+) to Ti(4+) transition is thought to contribute to some phases.

Loeffler, B. M.↗
NASA NTRS1980

Development of an All-Metal Thick Film Cost Effective Metallization System for Solar Cells

Materials including copper powders, silver-fluoride, and silicon wafers were procured and copper pastes were prepared. Electrodes made with copper pastes were analyzed and compared with the raw materials. A needle-like structure was observed on the electroded solar cells, and was identified as eutectic copper-silicon by electron probe X-ray spectroscopy. The existence of this phase was thought to benefit electrical and metallurgical properties of the contact. Subsequently electrodes made from new material were also shown to contain this phase while simultaneously having poor adhesion.

Ross, B.↗
NASA NTRS1981

Development of an all-metal thick-film cost-effective metallization system for solar cells

Screened electrodes made from fluorocarbon activated copper paste and silver fluoride activated copper paste, tape adhesion and scratch tests were studied. Experiments were conducted with variations in past parameters, firing conditions, including gas ambients, furnace furniture, silicon surface and others. A liquid medium intended to provide transport during the carbon fluoride decomposition, is incorporated in the paste.

Ross, B.↗
NASA NTRS1982

Method and apparatus for convection control of metallic halide vapor density in a metallic halide laser

An apparatus is disclosed in which a reservoir containing copper chloride is heated so that the copper chloride is maintained in a liquid form. The apparatus includes a means for flowing a buffer gas (which in the exemplary embodiment is neon) over the liquid copper chloride to provide a mixture of copper chloride vapor and neon above the liquid copper chloride. A conduit provides fluid communication between the reservoir containing the copper chloride vapor/neon mixture and the laser. The copper chloride vapor density in the laser is related to the liquid copper chloride temperature and the neon flow rate through the reservoir. In accordance with a further feature of the exemplary embodiment, neon is also provided directly to the laser in order to provide a further means of controlling the copper chloride vapor density in the laser.

Pivirotto, T. J.↗
NASA NTRS1982

Development of an all-metal thick film cost effective metallization system for solar cells

Electrodes made with pastes produced under the previous contract were analyzed and compared with raw materials. A needle-like structure observed on the electroded solar cell was identified as eutectic copper-silicon, a phase considered to benefit the electrical and metallurgical properties of the contact. Electrodes made from copper fluorocarbon and copper silver fluoride also contained this phase but had poor adhesion. A liquid medium, intended to provide transport during carbon fluoride decomposition was incorporated into the paste resulting in better adhesion. The product survived preliminary environmental tests. A 2 cm by 2 cm solar cell made with fluorocarbon activated copper electrodes and gave 7% AMI efficiency (without AR coating). Both silver fluoride and fluorocarbon screened paste electrodes can be produced for approximately $0.04 per watt.

Ross, B.↗