Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “metal casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Minimizing thickness variation in monolithic U-10Mo fuel foil and Zr interlayer during hot rolling: A microstructure-based finite element method analysis

Low-enriched uranium alloyed with 10 wt. % molybdenum (U-10Mo) has been identified as a promising alternative to highly enriched uranium fuel for the United States’ high performance research reactors. The monolithic U-10Mo fuel plate consists of a metallic U-10Mo fuel foil with a 25 µm Zr interlayer and a relatively thick cladding of aluminum alloy 6061. The Zr interlayer is typically applied during the hot co-rolling process, and this process dictates the uniformity of the Zr interlayer. Thickness variation observed in the U-10Mo and Zr interlayer has been attributed to several sources: the initial grain size of the U-10Mo castings, can materials, rolling temperature, inhomogeneous molybdenum content, and porosity in the cast U-10Mo. This thickness variation limits the ability to meet the dimensional specification; thus, a better understanding of the factors causing the nonuniform thickness is needed. In this work, we used a novel, microstructure-based finite element method to model the hot rolling process to address these concerns. Grain microstructures in U-10Mo were tessellated and explicitly considered in the finite element model. Each grain was assigned a random material property to mimic the grain strength variations induced by different grain orientations. Simulations were performed using six steel can thicknesses, four grain sizes, and with or without a Zr interlayer to investigate the influences of those variables on the thickness nonuniformity. The simulation results showed that a thinner steel can and finer U-10Mo grain size reduce thickness variations in both the U-10Mo fuel foil and Zr interlayer. The direct findings from the simulations and analysis can be used to optimize the hot rolling schedule, reduce fabrication defects, and meet the dimensional specifications. The proposed microstructure-based finite element model can be also coupled with experimental microstructure characterization data, images, and models to simulate multi-pass hot rolling.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Corrosion Resistance of an AlCeMg/Stainless-Steel Reactive Bond

A major issue for metal components in many industries is corrosion as it can substantially reduce their lifetime. This issue is especially problematic for materials used in heat exchanger applications. Al–Ce–Mg alloys, which exhibit corrosion resistance and can reactively bond with other metals, may be a viable solution to this problem. This investigation studied the corrosion behavior of Al–2Ce–6Mg (atomic percent)/stainless-steel (SS) reactive bond interfaces after full immersion in nitric, sulfuric, formic, and mixed acid for 267 h. This particular Al–Ce–Mg alloy was chosen due to its good castability. The results of scanning electron microscope characterization showed that reactive bond formations repeatedly occurred throughout the length of the casting in the as-cut samples and that these formations maintained a secure bonding between the alloy and the stainless-steel tubes. Transmission electron microscopy results showed that there was a clear compositional and microstructural transition across the reactive bond. The results of the immersion tests indicated that the nitric, sulfuric, and the mixed acid did not have an observably negative effect on the reactive bond structure. As for the sample exposed to formic acid only, noticable changes were seen in both the microstructural appearance and the elemental profile across the bond, suggesting that oxide formation occurred.

Brechtl, Jamieson [ORNL] (ORCID:0000000217394283)↗
DOE OSTI2020

Contribution of cryogenic thermal cycling to the atomic dynamics in a La-based bulk metallic glass with different initial states

Structural rejuvenation in metallic glasses (MGs) induced by cryogenic thermal cycling has been intensively studied. However, the effect of thermal cycling on the atomic dynamics in MGs is still missing. In this work, we present a systematic study on the atomic dynamics in a La-based MG affected by sub-Tg annealing and thermal cycling. We find that the thermal cycling has little effect on the atomic dynamics in both as-cast and annealed MGs although it could significantly increase the free volume and change mechanical properties of the as-cast MG sample. In contrast, both the structure and mechanical properties of the well-relaxed sample are almost unchanged by thermal cycling. Further, the increased open volume, mainly in the form of atomic vacancies, does not greatly promote the atomic dynamics in the as-cast MG sample, indicating that the free volume induced by thermal cycling is not the key factor in stimulating the β-relaxation and the boson peak in the studied MG.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impacts of the Additive Manufacturing Process on the Roughness of Engine Scale Vanes and Cooling Channels

Abstract By leveraging the additive manufacturing (AM) platform, development time and costs for turbine component testing can be reduced relative to traditional investment casting. Surface roughness is a key characteristic of the additive manufacturing process that can impact flow, heat transfer, and mechanical integrity of printed components. There are multiple design and build considerations that result in variability in surface roughness, especially when additively fabricating complicated three-dimensional vanes and internal cooling passages. This study characterizes the surface roughness of internal cooling passages, vanes, and flat external surface samples made using additive manufacturing, specifically the direct metal laser sintering process. The samples were manufactured with various wall thicknesses, layer thicknesses, build locations, build directions, and on different AM machines. A combination of computed tomography scanning and optical profilometry was used to evaluate surface roughness levels. The data indicate that the dominant factors in roughness for a given layer thickness are a function of wall thickness, build location, and build direction.

Engineering↗
DOE OSTI2023

Elucidating Primary Degradation Mechanisms in High-Cycling-Capacity, Compositionally Tunable High-Entropy Hydrides

The hydrogen sorption properties of single-phase bcc (TiVNb) 100–x Cr x alloys (x = 0–35) are reported. All alloys absorb hydrogen quickly at 25 °C, forming fcc hydrides with storage capacity depending on the Cr content. Here, a thermodynamic destabilization of the fcc hydride is observed with increasing Cr concentration, which agrees well with previous compositional machine learning models for metal hydride thermodynamics. The steric effect or repulsive interactions between Cr–H might be responsible for this behavior. The cycling performances of the TiVNbCr alloy show an initial decrease in capacity, which cannot be explained by a structural change. Pair distribution function analysis of the total X-ray scattering on the first and last cycled hydrides demonstrated an average random fcc structure without lattice distortion at short-range order. If the as-cast alloy contains a very low density of defects, the first hydrogen absorption introduces dislocations and vacancies that cumulate into small vacancy clusters, as revealed by positron annihilation spectroscopy. Finally, the main reason for the capacity drop seems to be due to dislocations formed during cycling, while the presence of vacancy clusters might be related to the lattice relaxation. Having identified the major contribution to the capacity loss, compositional modifications to the TiVNbCr system can now be explored that minimize defect formation and maximize material cycling performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

A critical analysis of U-Pu-Zr phase transitions using calorimetric, microstructural, and phase equilibria data

Metallic fuels consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are a leading material candidate for fast-spectrum nuclear reactors. Early demonstration programs proved the principle of safe and efficient fast reactor operation, however there is still considerable uncertainty regarding the phase equilibria and microstructural evolution across the ternary composition space. Quantitative phase formation and identification measurements are scarce and often incomplete, with studies reporting either phase transition temperatures or phase identification data, but not both from the same specimens. In this study, we critically compared experimental and calculated phase transition data and correlated with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Differential scanning calorimetry (DSC) was used to measure phase transitions in the subsolidus regions (723−948 K) of three ternary U-Pu-Zr alloys with similar plutonium concentrations but various U/Zr ratios. Due to sluggish kinetics and narrow ranges of phase stability, complex peaks required the use of a Frazier-Suzuki peak fitting algorithm to deconvolute and calculate transition peak temperatures and enthalpies. We also identified trends of phase transition behavior by critically comparing our DSC data with previous phase transition measurements as well as historical and calculated phase equilibrium diagrams. In conclusion, this provides a critical approach for benchmarking and assessing the quality of new U-Pu-Zr phase equilibria data prior to its incorporation into nuclear material databases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Melting point of group IV and V transition metal diborides

The environmental conical nozzle levitator system enables cooling trace experiments above 4000 K. These cooling trace experiments were used to determine the melting points through observation of thermal arrest of group IV and V transition metal diborides (TiB 2 , T m = 3313 ± 33 K; ZrB 2 , T m = 3404 ± 38 K; HfB 2 , T m = 3529 ± 33 K; and TaB 2 , T m = 3284 ± 10 K; note: mean ± 2 standard error). Temperature measurements were conducted utilizing dual single-color pyrometers at wavelengths of 0.9 and 0.65 µm. This system utilizes aerodynamic levitation and dual laser heating to achieve temperatures approaching 4000 K. The samples were synthesized from commercial powders using ceramic gel-casting to produce high-density spherical components. The measurements obtained were compared to previously reported melting temperature values and were generally found to be in agreement with most of the published values.

Materials science↗
DOE OSTI2023

Effect of Mn on eutectic phase equilibria in Al-rich Al-Ce-Ni alloys

Microstructural analysis of additively manufactured (AM) Al-Ce-Ni-Mn alloys has identified phases not predicted from existing ternary liquidus projections in the Al-Ce-Ni system. Because the rapid cooling rate of AM is orders of magnitude above that of traditional casting, it is unclear if these additional phases arose from the non-equilibrium processing conditions of AM, a drastic shift in phase stability in the system due to the addition of 1 wt% Mn, or some combination of these two influences. The phases and microstructure of cast samples of Al-Ce-Ni and Al-Ce-Ni-Mn alloys were characterized for several annealing conditions which revealed the equilibrium phases at different temperatures. Phase analysis confirmed that minute levels of Mn substituted for Ni in the system drastically shifts the liquidus projection in the Al-rich corner of the ternary phase diagram such that the eutectic Al 3 Ni phase is suppressed in favor of the Al 23 Ni 6 (Ce,Mn) 4 phase. Further addition of Mn promotes the formation of Al 20 Mn 2 Ce and Al 10 Mn 2 Ce phases. The phase analysis data was then used to improve the CALPHAD modeling of the liquidus projection and isothermal sections for the Al-rich Al-Ce-Ni-Mn quaternary system. Thermodynamic modeling and experimental analysis on phases in the AM sample of Al-Ce-Ni with Mn confirmed that the phases present are consistent with Mn-containing Al-Ce-Ni cast samples. Here, this investigation demonstrates the potential for using secondary alloying elements to drastically alter phase stability and microstructure in alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrospun Si and Si/C Fiber Anodes for Li-Ion Batteries

Due to structural changes in silicon during lithiation/delithiation, most Li-ion battery anodes containing silicon show rapid gravimetric capacity fade upon charge/discharge cycling. Herein, we report on a new Si powder anode in the form of electrospun fibers with only poly(acrylic acid) (PAA) binder and no electrically conductive carbon. The performance of this anode was contrasted to a fiber mat composed of Si powder, PAA binder, and a small amount of carbon powder. Fiber mat electrodes were evaluated in half-cells with a Li metal counter/reference electrode. Without the addition of conductive carbon, a stable capacity of about 1500 mAh/g (normalized to the total weight of the anode) was obtained at 1C for 50 charge/discharge cycles when the areal loading of silicon was 0.30 mgSi/cm2, whereas a capacity of 800 mAh/g was obtained when the Si loading was increased to ~1.0 mgSi/cm2. On a Si weight basis, these capacities correspond to >3500 mAh/gSi. The capacities were significantly higher than those found with a slurry-cast powdered Si anode with PAA binder. There was no change in fiber anode performance (gravimetric capacity and constant capacity with cycling) when a small amount of electrically conductive carbon was added to the electrospun fiber anodes when the Si loading was ≤1.0 mgSi/cm2.

Mondal, Abhishek N.↗
DOE OSTI2020

Assessment of Impurities in Neptunium Metal Using Double-Focusing SF-ICP-MS

In the transmutation process, minor actinides such as neptunium, americium and curium obtained from spent nuclear fuel are incorporated into new fuel that can be placed into a fast reactor, where these elements fission into products with shorter half-lives which reduces the health and safety hazards. In order to better understand the all the involved processes, fundamental physical properties of actinides should be investigated, and for that reason, high-purity materials need to be produced. One of the main challenges in characterizing these materials is the lack of pure metal available for study, and lack of analytical methods to determine the purity. Trans-uranic elements are challenging to study because of the need to be handled in specialized facilities, safeguards concerns and they are not easily purchased and/or produced. High-purity Np metal is being produced at the Materials and Fuels Complex (MFC) of Idaho National Laboratory (INL), in a process of direct oxide reduction developed by Squires and Lessing, with a target purity of 99.999%. The goal of this research is to develop methods to determine the impurities in the Np metal, with detection limits low enough to achieve this purity level. In this work, we have used several ICP-MS and ICP OES techniques, but the focus was the method development using a recently acquired Double-Focusing Sector Field Inductively Coupled Plasma Mass Spectrometer (SF-ICP-MS). To produce the Np metal, approximately 20 g of the neptunium oxide powder was calcined at 800 oC for 6 h in a magnesium oxide crucible, which is placed inside a stainless steel crucible, that goes into the Hot Uniaxial Press (HUP) furnace insert. After the calcining step, the Np oxide was mixed with approximately 9 g of calcium metal and 100 g of ultra-dry calcium chloride. The HUP furnace was heated in a ramp rate of 50 oC min -1 up to 1000 oC. When the reaction mixture reached 850 oC, a tantalum stirrer was activated at 100 rpm. After the tantalum stirrer was removed and the mixture cooled overnight, the MgO crucible was opened with a hammer and chisel to retrieve the Np metal button at the bottom of the reaction mixture. Prior to the dissolution process, the surface contaminants of the sample were removed. The Np button was washed in 10 mL of ultra-pure water for 1 min, with a faint reaction observed on the surface, indicating the presence of Ca metal. The water-washed sample was placed in a tube with 2 M HCl for only 3 s, as a vigorous reaction in the button surface was observed. The leachates were saved for further analysis. The sample was then rinsed with ultra-pure water and air-dried prior to dissolution. The cleaned sample was placed in a PTFE beaker and 25 mL of 6 M HCl and 150 µL of 24 M HF were added. After 10 minutes of reaction, the beaker was placed on a hot plate for 1 h and 30 min, followed by the addition of 1 mL of 16 M HNO3 and allowed to react for a further 1 h and 20 min. The sample was removed from heat and 10 mL of HNO3 16 M was added to react with the HCl. The beaker was covered and left for overnight reaction, producing a solution with approximately 20 mL of final volume. A Quadrupole Inductively Coupled Plasma Mass Spectrometer (Q-ICP-MS, Perkin Elmer ELAN DRC II Q-ICP-MS) was used to obtain qualitative mass spectra for the dissolution blank, each of the leachates and the dissolved sample. In the water leachate spectrum mainly Ca and Mg were observed, while the acid wash had a similar peak pattern to the one observed for the Np metal sample, indicating that the process not only removed surface contamination, but also reacted with the sample itself. In the Np material spectrum, Ta and actinides were identified as candidates for major contaminants, as the most intense peaks corresponded to the mass-to-charge ratios of these elements. Minor contaminants included Al, Au, Ca, Cr, Fe, I, Na, Nb, Pb, Sn, Ti, Tl, V, Y. The presence of impurities in the material could have originated from several sources, such as the materials used for the casting process, the use of impure NpO2 or contamination of reagents and materials used for the analysis. Some of the isotopes listed as potential contaminants are susceptible to spectral interferences, so Double-Focusing SF-ICP-MS (Nu Instruments Attom ES HR-ICP-MS) was used for the quantitative analysis. For each isotope determined, several items were evaluated: raw signal of a blank solution, sensitivity and determination coefficient of calibration curves, possibility of interferences and comparison of results obtained for at least two resolving powers (RP): 300 and 4000. The evaluation of the signal in a blank solution can indicate if a spectral interference from the plasma gas and/or the solvent was successfully resolved (commonly observed for 52Cr+/40Ar12C+, for example). It is important to highlight that a signal reduction is expected when a higher RP is used, as the ion beam transmission is decreased by the use of narrower slits

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

An In-Depth Analysis of the Transformation of Tin Foil Anodes during Electrochemical Cycling in Lithium-Ion Batteries

Tin foils have an impressive lithium-storage capacity more than triple that of graphite anodes, and their adoption could facilitate a drastic improvement in battery energy density. However, implementation of a dense foil electrode architecture represents a significant departure from the standard blade-cast geometry with a distinct electrochemical environment, and this has led to confusion with regards to the first cycle efficiency of the system. In this work, we investigate the unique behavior of a tin active material in a foil architecture to understand its performance as an anode. We find shallow cycling of the foil results in an irreversible formation (< 40%) due to diffusional trapping, but intermediate and complete utilization allows for a remarkably reversible formation reaction (> 90%). This striking nonlinearity stems from an in situ transformation from bulk metal to porous electrode that occurs during formation cycles and defines electrode-level lithium-transport on subsequent cycles. As a result, an alternative cycling procedure for assessing the stability of foils is proposed to account for this chemomechanical effect.

25 ENERGY STORAGE↗
DOE OSTI2024

Ionic liquid mediated one-step perpendicular assembly in block copolymer thin films for ultrafiltration membrane applications

The rapid rise of oil and gas, petrochemical, food processing, and pharmaceutical industries has added a complex mixture of contaminants like oil, particulates, metals, and other organic compounds to wastewater. Multipurpose membranes with precise pore structure can offer a solution to this problem and block copolymers (BCP) can be used to achieve such structures. Achieving vertical assembly of BCP domains provides a perfect template for developing uniform through film channels for separation and transport of material, besides being useful for the rectification of defects in photolithography patterns. Producing such morphologies may require extensive film/substrate processing and is not always feasible for scale-up. With this article, we demonstrate a facile solution casting method to induce vertical domain assembly in as-cast diblock copolymer thin films in the presence of an ionic liquid (IL) additive that preferentially segregates to one block and neutralizes interfacial interactions. We also show the tunability of domain sizes by controlling the additive concentration. These vertically aligned morphologies are important for the development of next-generation lithographic techniques and form excellent templates for ultrafiltration membranes with uniform pore sizes. In conclusion, this article demonstrates how IL additives can be used to obtain stable non-equilibrium morphologies in as-cast BCP films and the effect of BCP molecular mass, block volume fractions, and IL content on self-assembly.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

High-Performance AEM LTE with Advanced Membranes, Ionomers and PGM-Free Electrodes

Alkaline low temperature electrolysis (LTE) systems enjoy several potential advantages over acid-based LTE systems including facile oxygen evolution reaction (OER) kinetics and electrodes that can use little to no platinum group metals (PGM). The polymer membranes and membrane electrode assembly (MEA) structures going into alkaline electrochemical systems have seen significant advances in recent years. The objective of this project is to combine state-of-the-art alkaline polymer electrolyzer components into one optimized membrane electrode assembly (MEA) system to achieve DOE low temperature electrolysis (LTE) goals. The benefit of individual component advances cannot be fully appreciated until all aspects and components of the MEA are working at an equally high level of performance. New electrode fabrication methods were developed where solvent cast catalyst/ionomer solutions were used in place of insoluble ionomers to significantly improve adhesion. The membranes were improved in terms of durability and mechanical properties. The OER and HER catalysts were improved and made more durable.

08 HYDROGEN↗
DOE OSTI2025

Delineating Confinement Regimes for Nafion Thin Films via Simultaneous QCM-D and Spectroscopic Ellipsometry

Proton-conducting ionomers used in electrodes of electrochemical devices form nanometer-scale films covering metallic catalyst surfaces, wherein they experience confinement and interfacial effects absent in the bulk polymer. This confinement alters the physical properties of the ionomer film, which is postulated to increase the density and is attributed to the transport limitations observed in fuel-cell electrodes. Despite studies showing reduced swelling, no systematic measurement has validated this phenomenon by demonstrating both densification and stiffening as the film gets thinner. Here, this study aims to fill this gap by reporting the humidity-driven changes in swelling, mass uptake, and density of Nafion ionomer films cast at varying thicknesses (10–320 nm) onto a gold-plated sensor. The films were simultaneously probed during humidification using spectroscopic ellipsometry (SE) and a quartz crystal microbalance with dissipation (QCM-D), which allowed for determination of the density and shear stiffness. The effects of confinement were prominently observed below ∼30 nm, with films showing increased density along with decreased swelling and mass uptake during hydration. In addition, the confined films show a negative excess volume upon initial water sorption, implying a larger proportion of absorbed water might bound to ionic groups in accord with notion of localized densification.

Espinet, Kevin B. [University of California, Berke↗
DOE OSTI2023

Synthesis and characteristics of porous ceramic tubes: a comparison of centrifugal casting and cold isostatic pressing methods

Short porous ceramic tubes in small quantities are needed for membrane-related research and development efforts and can be synthesized by centrifugal casting (CC) or cold isostatic pressing (CIP) methods. Here, this work evaluates the characteristics of porous ceramic tubes prepared by both methods and provides a strategy for selecting the proper method for ceramic tube fabrication, depending on its application. Samarium-doped ceria (SDC) with an average crystallite size of 10 nm was synthesized by a citrate method and used to make porous SDC tubes by the CC and CIP methods under different conditions. Porous SDC tubes were prepared from an aqueous suspension of the SDC powder with polyvinyl alcohol (PVA) using a cylindrical metallic mold, centrifugated at 4000–6000 rpm, followed by sintering in 1200–1500 °C. SDC tubes were also made by the CIP method from the SDC powder placed inside a cylindrical rubber bag followed by isostatic compression at 1379 bar. The pore structure of the SDC tubes was characterized by helium permeation and liquid nitrogen Archimedes method. Due to high compression pressure giving a low porosity green tube, the CIP method with lower sintering temperature produces SDC tubes with much lower porosity and average pore size and similar tortuosity compared to the CC methods. The CIP method should be used to prepare low porosity or dense ceramic tubes, and the CC method should be used for preparing high-porosity ceramic tubes or tubes with pore gradient tube wall.

36 MATERIALS SCIENCE↗
DOE OSTI2023

$In-situ$ synchrotron x-ray diffraction and thermal expansion of TiB2 up to ~3050 °C

There is an increasing interest in understanding the performance and properties of ultra-high temperature ceramics due to their high melting points (<3000 °C) that make them promising for extreme environment applications. In-situ high temperature X-ray diffraction experiments were performed on TiB 2 beads up to ~3050 °C. For these experiments, TiB 2 powders were fabricated into spherical beads via gel casting methods and densified in a high temperature graphite furnace. These sample beads were then levitated in a conical nozzle levitator with reducing atmosphere (3% H 2 -Ar) while being heated using a 400 W CO 2 laser. During levitation a collimated synchrotron X-ray source was used to perform in-situ, temperature-dependent structural characterizations. The anisotropic coefficients of thermal expansion of TiB 2 were characterized as a function of temperature up to ~3050 °C. Elucidation of these properties are critical for the advancement of TiB 2 ceramics and other transition metal di-borides for use in high temperature applications such as hypersonic platforms, nuclear reactors, and atmospheric re-entry.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Dislocation Patterning in Deforming Crystals: Theory, Computational Predictions and Validation (Final Technical Report)

This project was awarded for an initial period of three years, followed by a no-cost extension for one year and a funded one-year renewal. During the first four years, the project focused on investigating the role of dislocation reactions and dislocation correlation in dislocation patterning in FCC metals. During the fifth year, the scope of research was expanded to investigate the effects of composition inhomogeneity on the mesoscale plastic response of Body-Centered Cubic (BCC) alloys. In addition to its impact on metal hardening during deformation, dislocation patterning provides the microstructure information required to understand phenomena like fracture and recrystallization in metals. The Continuum Dislocation Dynamics (CDD) framework was the methodology used during the first four years, followed by the use of Discrete Dislocation Dynamics (DDD) during the fifth year. CDD is a density-based formalism of dislocation dynamics in which the plastic deformation of crystals is predicted together with the mesoscale dislocation patterns by tracking the space-time evolution of dislocations as driven by the applied stress, short-range and long-range interactions of dislocations, and cross slip. CDD is a crystal mechanics approach in which the plastic constitutive part is replaced with the equations of dislocation dynamics, which is driven by the internal stress via a mobility laws, while the evolution of the density gives the eigenstrain required to update the internal stress itself. The governing equations are thus those of crystal mechanics cast as an eigenstrain problem and those of dislocation transport and reactions. Our investigations during the first four years were driven by the hypothesis that that dislocation patterning is triggered by spatiotemporal dislocation density and internal stress fluctuations, and that such fluctuations influence the collective dislocation dynamic through their effects on the short-range reaction rates and the collective dislocation mobility. This hypothesis was tested by modeling the influence of the dislocation reactions and dislocation correlations on collective dislocation dynamics. The main research components during the first four years were: 1) Reformulation of the CDD framework to integrate the dislocation correlations and dislocation reactions. 2) Simulation of the dislocation correlations and quantifying their contribution to the long-range stress of complex dislocation systems. 3) Computational implementation of the updated CDD model for FCC single crystals and development of an efficient CDD code. 4) Investigation of dislocation patterning in FCC crystals based on the updated CDD model. Some key findings from these investigations were: 1) The patterning of dislocations is initiated by cross slip and internal stress fluctuations, and the refinement of the pattern results from junction formation. 2) Patterning is more prominent under high stress. 3) The correlation stress was found to be a significant part of the mean field stress in continuum representations of dislocation dynamics. During the last year of the project, we have established a method for performing dislocation dynamics in inhomogeneous alloys and demonstrated the impact of composition inhomogeneity on the characteristics of initial yielding and dislocation character in BCC alloys. We also tested this method using an irradiated ferritic alloy in which the composition and dislocation loops effects are both present. In doing so, we have considered two aspects of the role of inhomogeneity, the creation of internal coherency stress due to the dependence of the lattice parameter on the local composition, and the dependence of the dislocation mobility on the local composition. These two aspects resulted in an unexpected behavior of the dislocation system, and, in turn, the yielding behavior of BCC alloys. Key findings include: 1) The composition inhomogeneity in BCC alloys alters the well-known role of screw dislocations by forcing a level of waviness on the average dislocation character, thus destroying the screw character dominance in the yielding observed in pure or homogeneous BCC metals. 2) In the case of irradiated alloys, while composition inhomogeneity by itself and dislocation loops by themselves result in some hardening, the superposition of the two mechanisms does not result in the sum of the two contributions via any known rule. The latter result contradicts the classical works related hardening via multiple mechanisms, which state that various hardening mechanisms can be added linearly or using some Pythagorean additive rule. We were able to rationalize this unexpected result by a closer loop at the origin of the hardening mechanisms themselves, which both involved long-range elastic interactions with dislocations. We reached the conclusion that the hardening resulting from the total stress associated with these two mechanisms (current work) differs from the sum of the effects of the individual stress fields (classical literature). We have also found a major flaw in the classical theory of spinodal hardening. The latter theory never considered the impact of composition undulation on the solute hardening. We have built a new general theory accounting for the effect of solute friction together with the composition undulations on the dislocation configuration at Critical Resolved Shear Stress (CRSS), which is yielding a new definition of the spinodal hardening and new different results. This work is the first to recognize the lack of the role of solute in spinodal hardening theory of alloys.

36 MATERIALS SCIENCE↗