SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Metal and alloys micro and macro stress-strain behavior data correlated for linear differential transformers, strain gages, longitudinal resonance waves and X ray diffraction
This document describes the Kepler PRF/FPG data release. This data was taken on April 27-29, 2009, during Kepler's commissioning phase in order to measure the pixel response function (PRF) (Bryson et al., 2010a) and focal plane geometry (FPG) (Tenenbaum and Jenkins, 2010). 33,424 stellar targets were observed for 243 long cadences, each with a duration of 14.7 minutes (half the duration of a normal Kepler long cadence). During these 243 cadences the Kepler photometer was moved, pointing in a dither pattern to facilitate PRF measurement. Motion occurred during the even cadences (second, fourth, etc.), with the telescope in stable fine point at each pointing in the dither pattern during the odd cadences (first, third, etc.). The first and last cadences were at the center of the dither pattern. Motion cadences are included in this release, but they do not contain any data. For details on how this data was used to derive the Kepler PRF and FPG models, see Bryson et al. (2010a) and Tenenbaum and Jenkins (2010). Descriptions of the PRF and FPG models are found in Thompson et al. (2016), x2.3.5.17 and x2.3.5.16 respectively. The data in this release can be used to recompute the Kepler PRF and FPG. Such a reconstruction, however, would not reflect measured seasonal changes in the PRF described in Van Cleve et al. (2016b), x5.2.The dither pattern is shown in Figure 1. The crosses show the commanded pointings and the circles show the measured pointings. Measured pointings are different from the commanded pointings due to the early state of calibration of the fine guidance sensors during commissioning (Van Cleve et al., 2016a). The measured offsets from the center of the pattern are given in RADEC offsets and pixel offsets in Table 1. The order of the offsets was randomized during data collection to avoid time-dependent systematics.
The FIELDS instrumentation suite on the Magnetospheric Multiscale (MMS) mission provides comprehensive measurements of the full vector magnetic and electric fields in the reconnection regions investigated by MMS, including the dayside magnetopause and the night-side magnetotail acceleration regions out to 25 Re. Six sensors on each of the four MMS spacecraft provide overlapping measurements of these fields with sensitive cross-calibrations both before and after launch. The FIELDS magnetic sensors consist of redundant flux-gate magnetometers (AFG and DFG) over the frequency range from DC to 64 Hz, a search coil magnetometer (SCM) providing AC measurements over the full whistler mode spectrum expected to be seen on MMS, and an Electron Drift Instrument (EDI) that calibrates offsets for the magnetometers. The FIELDS three-axis electric field measurements are provided by two sets of biased double-probe sensors (SDP and ADP) operating in a highly symmetric spacecraft environment to reduce significantly electrostatic errors. These sensors are complemented with the EDI electric measurements that are free from all local spacecraft perturbations. Cross-calibrated vector electric field measurements are thus produced from DC to 100 kHz, well beyond the upper hybrid resonance whose frequency provides an accurate determination of the local electron density. Due to its very large geometric factor, EDI also provides very high time resolution (∼1 ms) ambient electron flux measurements at a few selected energies near 1 keV. This paper provides an overview of the FIELDS suite, its science objectives and measurement requirements, and its performance as verified in calibration and cross-calibration procedures that result in anticipated errors less than 0.1 nT in B and 0.5 mV/m in E. Summaries of data products that result from FIELDS are also described, as well as algorithms for cross-calibration. Details of the design and performance characteristics of AFG/DFG, SCM, ADP, SDP, and EDI are provided in five companion papers.
Detailed flow measurements made in the casing boundary layer of a two-stage transonic fan are summarized. These measurements were taken at a station upstream of the fan, between all blade rows, and downstream of the last row. Conventional boundary layer parameters were calculated from the measured data. A classical two dimensional casing boundary layer was measured at the fan inlet and extended inward to approximately 15 percent of span. A highly three dimensional boundary layer was measured at the exit of each blade row and extended inward to approximately 10 percent of span. The steep radial gradient of axial velocity noted at the exit of the rotors was reduced substantially as the flow passed through the stators. This reduced gradient is attributed to flow mixing. The amount of flow mixing was reflected in the radial redistribution of total temperature as the flow passed through the stators. The blockage factors calculated from the measured data show an increase in blockage across the rotors and a decrease across the stators. For this fan the calculated blockages for the second stage were essentially the same as those for the first stage.
The Orbital Debris Engineering Model (ORDEM) developed by the NASA Orbital Debris Program Office (ODPO) is a data-driven model — extensive radar, optical, laboratory, and in situ measurement data sets have been used to build the model since its earliest versions. A salient aspect of professional software development is the verification and validation (V&V) process. Verification answers the question “Is the model built correctly?” while validation addresses the question “Did we build the correct model?” Less extensive, reserved, or independent data sets serve the validation requirement. Due to the dynamic nature of the orbital debris environment, it is critical to use contemporaneous data sources that represent the current environment to support ORDEM development and validation. ORDEM has utilized in situ data collected from Space Shuttle and Hubble Space Telescope surface inspections, now over a decade old. This historical dataset is fundamental for providing baseline in situ measurement data for sizes between 10 to 300 microns, but new data sources are being evaluated using returned surfaces from or near the International Space Station (ISS). This paper reviews a general microscopic survey of ISS soft goods, the Pressurized Mating Adapter 2 (PMA-2) blanket, and a limited-scope feasibility study conducted on the Space Exploration Technologies Corporation (SpaceX) Dragon capsule’s Thermal Protection System (TPS) material. The PMA-2 blanket, exposed to the space environment between 09 July 2013 and 25 February 2015, is an approximately 3.7 m2-area blanket composed of a betacloth outer layer and multiple ballistic fabric inner layers. The SpaceX Cargo Dragon capsule regularly visited the ISS from 2012 through 2020 and potentially provides a timely and well-characterized source of data for modeling purposes. The capsule’s lateral surfaces use SpaceX Proprietary Ablative Material (SPAM) TPS material, a syntactic foam, for thermal management during all mission phases. Seven SPAM extracted samples have been analyzed to date. This paper will provide an overview of the characterization completed for impact features by size, depth, impactor diameter, and the impactor residues chemical analyses, allowing a differentiation between micrometeoroids and orbital debris and a categorization by mass density and density class. Impactor diameter is estimated using damage equations generated from ground-based hypervelocity impact testing. The orbital debris impactors are compared to the current ORDEM 3.2 model of the environment at ISS altitudes. We briefly discuss the meteoroid impactors, including constituents and mass densities, in the general context of current models.
The Orbital Debris Engineering Model (ORDEM) developed by the NASA Orbital Debris Program Office (ODPO) is a data-driven model — extensive radar, optical, laboratory, and in situ measurement data sets have been used to build the model since its earliest versions. A salient aspect of professional software development is the verification and validation (V&V) process. Verification answers the question “Is the model built correctly?” while validation addresses the question “Did we build the correct model?” Less extensive, reserved, or independent data sets serve the validation requirement. Due to the dynamic nature of the orbital debris environment, it is critical to use contemporaneous data sources that represent the current environment to support ORDEM development and validation. ORDEM has utilized in situ data collected from Space Shuttle and Hubble Space Telescope surface inspections, now over a decade old. This historical dataset is fundamental for providing baseline in situ measurement data for sizes between 10 to 300 microns, but new data sources are being evaluated using returned surfaces from or near the International Space Station (ISS). This paper reviews a general microscopic survey of ISS soft goods, the Pressurized Mating Adapter 2 (PMA-2) blanket, and a limited-scope feasibility study conducted on the Space Exploration Technologies Corporation (SpaceX) Dragon capsule’s Thermal Protection System (TPS) material. The PMA-2 blanket, exposed to the space environment between 09 July 2013 and 25 February 2015, is an approximately 3.7 m2-area blanket composed of a betacloth outer layer and multiple ballistic fabric inner layers. The SpaceX Cargo Dragon capsule regularly visited the ISS from 2012 through 2020 and potentially provides a timely and well-characterized source of data for modeling purposes. The capsule’s lateral surfaces use SpaceX Proprietary Ablative Material (SPAM) TPS material, a syntactic foam, for thermal management during all mission phases. Seven SPAM extracted samples have been analyzed to date. This paper will provide an overview of the characterization completed for impact features by size, depth, impactor diameter, and the impactor residues chemical analyses, allowing a differentiation between micrometeoroids and orbital debris and a categorization by mass density and density class. Impactor diameter is estimated using damage equations generated from ground-based hypervelocity impact testing. The orbital debris impactors are compared to the current ORDEM 3.2 model of the environment at ISS altitudes. We briefly discuss the meteoroid impactors, including constituents and mass densities, in the general context of current models.
An unstructured grid flow solver, FUN3D has been used for simulation of unsteady flow on a partially dressed nose landing gear with closed cavities. Results obtained from an hybrid RANS/LES and delayed DES turbulence models are presented. Solutions have been obtained for a series of successively finer grids to quantify the effect of grid refinement. Computed surface pressures and perturbation pressures, and flow quantities in selected planes are compared with the experimental data. The power spectral density at several locations is also compared with the measured data. Overall agreement of FUN3D results with the experimental data is encouraging and the correlation with the measured data generally improves with grid refinement.
An unstructured grid flow solver, FUN3D has been used for simulation of unsteady flow on a partially dressed nose landing gear with closed cavities. Results obtained from an hybrid RANS/LES and delayed DES turbulence models are presented. Solutions have been obtained for a series of successively finer grids to quantify the effect of grid refinement. Computed surface pressures and perturbation pressures, and flow quantities in selected planes are compared with the experimental data. The power spectral density at several locations is also compared with the measured data. Overall agreement of FUN3D results with the experimental data is encouraging and the correlation with the measured data generally improves with grid refinement.
The rigid lid model was developed to predict three dimensional temperature and velocity distributions in lakes. This model was verified at various sites (Lake Belews, Biscayne Bay, etc.) and th verification at Lake Keowee was the last of these series of verification runs. The verification at Lake Keowee included the following: (1) selecting the domain of interest, grid systems, and comparing the preliminary results with archival data; (2) obtaining actual ground truth and infrared scanner data both for summer and winter; and (3) using the model to predict the measured data for the above periods and comparing the predicted results with the actual data. The model results compared well with measured data. Thus, the model can be used as an effective predictive tool for future sites.
The recent test program, in which the SR-2 and SR-3 Prop-Fan models were acoustically tested in flight, is described and the results of analysis of noise data acquired are discussed. The trends of noise levels with flight operating parameters are shown. The acoustic benefits of the SR-3 design with swept blades relative to the SR-2 design with straight blades are shown. Noise data measured on the surface of a small-diameter microphone boom mounted above the fuselage and on the surface of the airplane fuselage are compared to show the effects of acoustic propagation through a boundary layer. Noise level estimates made using a theoretically based prediction methodology are compared with measurements.
This paper gives an overview of the analysis of global precipitation over the last few decades and the impact of the new TRMM precipitation observations. The 20+ year, monthly, globally complete precipitation analysis of the World Climate Research Program's (WCRP/GEWEX) Global Precipitation Climatology Project (GPCP) is used to study global and regional variations and trends and is compared to the much shorter TRMM (Tropical Rainfall Measuring Mission) tropical data set. The GPCP data set shows no significant trend in precipitation over the twenty years, unlike the positive trend in global surface temperatures over the past century. The global trend analysis must be interpreted carefully, however, because the inhomogeneity of the data set makes detecting a small signal very difficult, especially over this relatively short period. Identifying regional trends in precipitation may be more practical. From 1979 to 1999 the northern mid-latitudes appear to be drying, the southern mid-latitudes have gotten wetter, and there is a mixed signal in the tropics. The relation between this field of trends and the relation to the frequency of El Nino events during this time period is explored. Monthly anomalies of precipitation are related to ENSO variations with clear signals extending into middle and high latitudes of both hemispheres. The El Nino and La Nina mean anomalies are near mirror images of each other and when combined produce an ENSO signal with significant spatial continuity over large distances. These El Nino minus La Nina composites of normalized precipitation show the usual positive, or wet, anomaly over the central and eastern Pacific Ocean with the negative, or dry, anomaly over the maritime continent along with an additional negative anomaly over Brazil and the Atlantic Ocean extending into Africa and a positive anomaly over the Horn of Africa and the western Indian Ocean. A number of the features are shown to extend into high latitudes. Positive anomalies extend in the Southern Hemisphere (S.H.) from the Pacific southeastward across Chile and Argentina into the south Atlantic Ocean. In the Northern Hemisphere (N.H.) the counterpart feature extends across the southern US and Atlantic Ocean into Europe. Further to the west a negative anomaly extends southeastward again from the Maritime Continent across the South Pacific and through the Drake Passage. The N.H. counterpart crosses the North Pacific and southern Canada. In the Southern Hemisphere an anomaly feature is shown to spiral into the Antarctica land mass. The extremes of ENSO-related anomalies are also examined and indicate that globally, during both El Nino and La Nina, more extremes of precipitation ( both wet and dry) occur than during the "neutral" regime, with the El Nino regime showing larger magnitudes. The distribution is different for the globe as a whole and when the area is restricted to just land. The recent (1998-present) TRMM observations are compared with the similar period of GPCP analyses with very good agreement in terms of pattern and generally good agreement with regard to magnitude. However, there still are differences among the individual TRMM products using passive and active microwave techniques and these need to be resolved before longer-term products such as the GPCP analyses can be validated.
This paper gives an overview of the analysis of global precipitation over the last few decades and the impact of the new TRMM precipitation observations. The 20+ year, monthly, globally complete precipitation analysis of the World Climate Research Program's (WCRP/GEWEX) Global Precipitation Climatology Project (GPCP) is used to study global and regional variations and trends and is compared to the much shorter TRMM(Tropical Rainfall Measuring Mission) tropical data set. The GPCP data set shows no significant trend in global precipitation over the twenty years, unlike the positive trend in global surface temperatures over the past century. The global trend analysis must be interpreted carefully, however, because the inhomogeneity of the data set makes detecting a small signal very difficult, especially over this relatively short period. The relation of global (and tropical) total precipitation and ENSO events is quantified with no significant signal when land and ocean are combined. Identifying regional trends in precipitation may be more practical. From 1979 to 2000 the tropics have pattern of regional rainfall trends that has an ENSO-like pattern with features of both the El Nino and La Nina. This feature is related to a possible trend in the frequency of ENSO events (either El Nino or La Nina) over the past 20 years. Monthly anomalies of precipitation are related to ENSO variations with clear signals extending into middle and high latitudes of both hemispheres. The El Nino and La Nina mean anomalies are near mirror images of each other and when combined produce an ENSO signal with significant spatial continuity over large distances. A number of the features are shown to extend into high latitudes. Positive anomalies extend in the Southern Hemisphere (S.H.) from the Pacific southeastward across Chile and Argentina into the south Atlantic Ocean. In the Northern Hemisphere (N.H.) the counterpart feature extends across the southern U.S. and Atlantic Ocean into Europe. Further to the west a negative anomaly extends southeastward again from the Maritime Continent across the South Pacific and through the Drake Passage. In the Southern Hemisphere an anomaly feature is shown to spiral into the Antarctica land mass. The extremes of ENSO-related anomalies are also examined and indicate that globally, during both El Nino and La Nina, more extremes of precipitation (both wet and dry) occur than during the "neutral" regime, with the El Nino regime showing larger magnitudes. The distribution is different for the globe as a whole and when the area is restricted to just land. The recent (1998-present) TRMM observations are compared with the similar period of GPCP analyses with very good agreement in terms of pattern and generally good agreement with regard to magnitude. However, there still are differences among the individual TRMM products using passive and active microwave techniques and these need to be resolved before longer-term products such as the GPCP analyses can be validated.
The wake characteristics of a rotorcraft are affected by the proximity of a rotor to the ground surface, especially during hover. Ground effect is encountered when the rotor disk is within a distance of a few rotor radii above the ground surface and results in an increase in thrust for a given power relative to that same power condition with the rotor out of ground effect. Although this phenomenon has been highly documented and observed since the beginning of the helicopter age, there is still a relatively little amount of flow-field data existing to help understand its features. Joint Army and NASA testing was conducted at NASA Langley Research Center using a powered rotorcraft model in hover at various rotor heights and thrust conditions in order to contribute to the complete outwash data set. The measured data included outwash velocities and directions, rotor loads, fuselage loads, and ground pressures. The researchers observed a linear relationship between rotor height and percent download on the fuselage, peak mean outwash velocities occurring at radial stations between 1.7 and 1.8 r/R regardless of rotor height, and the measurement azimuthal dependence of the outwash profile for a model incorporating a fuselage. Comparisons to phase-locked PIV data showed similar contours but a more contracted wake boundary for the PIV data. This paper describes the test setup and presents some of the averaged results.
The Marine Optical Buoy (MOBY) is the centerpiece of the primary ocean measurement site for calibration of satellite ocean color sensors based on independent in situ measurements. Since late 1996, the time series of normalized water-leaving radiances L(sub WN)(lambda) determined from the array of radiometric sensors attached to MOBY are the primary basis for the on-orbit calibrations of the USA Sea-viewing Wide Field-of-view Sensor (SeaWiFS), the Japanese Ocean Color and Temperature Sensor (OCTS), the French Polarization Detection Environmental Radiometer (POLDER), the German Modular Optoelectronic Scanner on the Indian Research Satellite (IRS1-MOS), and the USA Moderate Resolution Imaging Spectrometer (MODIS). The MOBY vicarious calibration L(sub WN)(lambda) reference is an essential element in the international effort to develop a global, multi-year time series of consistently calibrated ocean color products using data from a wide variety of independent satellite sensors. A longstanding goal of the SeaWiFS and MODIS (Ocean) Science Teams is to determine satellite-derived L(sub WN)(labda) with a relative combined standard uncertainty of 5 %. Other satellite ocean color projects and the Sensor Intercomparison for Marine Biology and Interdisciplinary Oceanic Studies (SIMBIOS) project have also adopted this goal, at least implicitly. Because water-leaving radiance contributes at most 10 % of the total radiance measured by a satellite sensor above the atmosphere, a 5 % uncertainty in L(sub WN)(lambda) implies a 0.5 % uncertainty in the above-atmosphere radiance measurements. This level of uncertainty can only be approached using vicarious-calibration approaches as described below. In practice, this means that the satellite radiance responsivity is adjusted to achieve the best agreement, in a least-squares sense, for the L(sub WN)(lambda) results determined using the satellite and the independent optical sensors (e.g. MOBY). The end result of this approach is to implicitly absorb unquantified, but systematic, errors in the atmospheric correction, incident solar flux, and satellite sensor calibration into a single correction factor to produce consistency with the in situ data.
Portable microwave test packages used to evaluate a new 34-m-diameter beam-waveguide (BWG) antenna are described. The experimental methodology involved transporting test packages to different focal points of the BWG system and making noise temperature, antenna efficiency, and holography measurements. Comparisons of data measured at the different focal points enabled determinations of performance degradations caused by various mirrors in the BWG system. It is shown that, due to remarkable stabilities and accuracies of radiometric data obtained through the use of the microwave test packages, degradations caused by the BWG system were successfully determined.
The formulation of a recursive maximum likelihood navigation system employing reference position and velocity vectors as state variables is presented. Convenient forms of the required variational equations of motion are developed together with an explicit form of the associated state transition matrix needed to refer measurement data from the measurement time to the epoch time. Computational advantages accrue from this design in that the usual forward extrapolation of the covariance matrix of estimation errors can be avoided without incurring unacceptable system errors. Simulation data for earth orbiting satellites are provided to substantiate this assertion.
Noise data measurements from a large scale lift fan transport model aircraft were made in the 40- by 80-foot wind tunnel. The model had two lift fans in deep inlets in the forward fuselage and two lift-cruise fans in pods on the aft fuselage. The noise data measurements are presented as listings and plots of sounds pressure level versus 1/3-octave center frequency.
Scientific and ecological needs call for the generation of a global data base of measured data from the Earth's atmosphere, similar but complementary to the data of the meteorological service. Right now there is a large gap between these needs and the available financial means. If this prevails, it might be prohibitive for the generation of such a data base. There must be a compromise between the needs and the means. Priorities must be set. Thus, discussions should be started on which data can be or should be stored. Newly generated data for storage in such a data base is recommended to be handled by the World Data Centers (WDCs). This brief report should help to stimulate discussions and ubsequent actions.