Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “loss measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Solid-gas phase equilibria and thermodynamic properties of cadmium selenide.

Accurate vapor pressures are determined through direct weight loss measurements using the Knudsen effusion technique. The experimental data are evaluated by establishing the mode of vaporization and determining the heat capacity of cadmium selenide at elevated temperatures. Additional information is obtained through a second- and third-law evaluation of data, namely, the heat of formation and the absolute entropy of cadmium selenide. A preferential loss of selenium during the initial heating of CdSe is observed, which leads to a deviation in stoichiometry.

Sigai, A. G.↗
NASA NTRS1989

Sound transmission loss of integrally damped, curved panels

Results are reported from acoustic transmission-loss measurements on 13 curved Al and composite aircraft-type panels (height 0.81 m, arc length 1.32 m, and curvature radius 2.29 m) without and with integral damping of various types. The fabrication of the panels and the test procedures are described and illustrated with photographs, and the results are presented in graphs. It is found that the loss of a curved panel exceeds the mass-law-predicted loss for a flat panel of the same material and thickness at frequencies below the ring frequency. At higher frequencies, the curved-panel loss is lower than the mass-law loss, being proportional to 20 time the log of thickness. Integral damping is found to be effective both below and above the ring frequency, but different mechanisms are responsible in each case.

Grosveld, Ferdinand W.↗
NASA NTRS1979

Fundamentals of heat measurement

Various methods and devices for obtaining experimental data on heat flux density over wide ranges of temperature and pressure are examined. Laboratory tests and device fabrication details are supplemented by theoretical analyses of heat-conduction and thermoelectric effects, providing design guidelines and information relevant to further research and development. A theory defining the measure of correspondence between transducer signal and the measured heat flux is established for individual (isolated) heat flux transducers subject to space and time-dependent loading. An analysis of the properties of stacked (series-connected) transducers of various types (sandwich-type, plane, and spiral) is used to derive a similarity theory providing general governing relationships. The transducers examined are used in 36 types of derivative devices involving direct heat loss measurements, heat conduction studies, radiation pyrometry, calorimetry in medicine and industry and nuclear reactor dosimetry.

Gerashchenko, O. A.↗
DOE OSTI2023

Diversifying and perennializing plants in agroecosystems alters retention of new C and N from crop residues

Abstract Managing soils to retain new plant inputs is key to moving toward a sustainable and regenerative agriculture. Management practices, like diversifying and perennializing agroecosystems, may affect the decomposer organisms that regulate how new residue is converted to persistent soil organic matter. Here we tested whether 12 years of diversifying/perennializing plants in agroecosystems through extended rotations or grassland restoration would decrease losses of new plant residue inputs and, thus, increase retention of carbon (C) and nitrogen (N) in soil. We tracked dual‐labeled ( 13 C and 15 N), isotopically enriched wheat ( Triticum aestivum ) residue in situ for 2 years as it decomposed in three agroecosystems: maize–soybean (CS) rotation, maize–soybean–wheat plus red clover and cereal rye cover crops (CSW2), and spring fallow management with regeneration of natural grassland species (seven to 10 species; SF). We measured losses of wheat residue (C wheat and N wheat ) in leached soil solution and greenhouse gas fluxes, as well as how much was recovered in microbial biomass and bulk soil at 5‐cm increments down to 20 cm. CSW2 and SF both had unique, significant effects on residue decomposition and retention dynamics that were clear only when using nuanced metrics that able to tease apart subtle differences. For example, SF retained a greater portion of C wheat in 0–5 cm surface soils (155%, p = 0.035) and narrowed the C wheat to N wheat ratio ( p < 0.030) compared to CS. CSW2 increased an index of carbon‐retention efficiency, C wheat retained in the mesocosm divided by total measured, from 0.18 to 0.27 (49%, p = 0.001), compared to CS. Overall, we found that diversifying and extending the duration of living plants in agroecosystems can lead to greater retention of new residue inputs in subtle ways that require further investigation to fully understand.

McDaniel, Marshall D.↗
NASA NTRS2002

Space Flight Experiments to Measure Polymer Erosion and Contamination on Spacecraft

Atomic oxygen erosion and silicone contamination are serious issues that could damage or destroy spacecraft components after orbiting for an extended period of time, such as on a space station or satellite. An experiment, the Polymer Erosion And Contamination Experiment (PEACE) will be conducted to study the effects of atomic oxygen (AO) erosion and silicone contamination, and it will provide information and contribute to a solution for these problems. PEACE will fly 43 different polymer materials that will be analyzed for AO erosion effects through two techniques: mass loss measurement and recession depth measurement. Pinhole cameras will provide information about the arrival direction of AO, and silicone contamination pinhole cameras will identify the source of silicone contamination on a spacecraft. All experimental hardware will be passively exposed to AO for up to two weeks in the actual space environment when it flies in the bay of a space shuttle. A second set of the PEACE Polymers is being exposed to the space environment for erosion yield determination as part of a second experiment, Materials International Space Station Experiment (MISSE). MISSE is a collaboration between several federal agencies and aerospace companies. During a space walk on August 16, 2001, MISSE was attached to the outside of the International Space Station (ISS) during an extravehicular activity (EVA), where it began its exposure to AO for approximately 1.5 years. The PEACE polymers, therefore, will be analyzed after both short-term and long-term AO exposures for a more complete study of AO effects.

Lillis, Maura C.↗
NASA NTRS1991

Atomic oxygen erosion of polymer matrix composites

Results are presented on atomic oxygen erosion of circular tubes and flat plates fabricated from different epoxy matrix composites containing, boron and Kevlar fiber reinforcements. The UTIAS experiment was located at station D-12, at 90 deg to the LDEF leading edge which was yawed about approximately 8 to 10 deg relative to the velocity vector. This resulted in enhanced atomic oxygen exposure at D-12, providing a total fluence of about 4 x 10(exp 20) atoms/sq cm. Thickness loss measurements were obtained for both flat plates and cylindrical tubes. The effect of reflected atomic oxygen on erosion yield and surface morphology on back surfaces (not directly exposed to AO) are graphically demonstrated. Erosion yields are also compared with other space flight data for similar materials, and ground-based tests in the UTIAS AO simulator. The effect of angle of incidence on surface morphology, erosion profiles and thickness losses are presented and the results correlated with simulator tests as well.

Tennyson, R. C.↗
NASA NTRS1975

Effect of potassium depletion in normal males - An Apollo 15 simulation

In the course of Apollo 15, physiologic abnormalities, manifested by ectopic activity on the ECG and unusual alterations in exercise tolerance, occurred in the crew of the Lunar Excursion Module. These were associated with decreases in total body potassium, measured by K-42, of 10% and 15%. The possibility of inadequate potassium (K+) intake existed. A simulation study was performed prior to Apollo 16, corresponding in duration to Apollo 15. Subjects endured the same sleep aberrations and caloric expenditure as the Apollo 15 astronauts. Subjects consumed a diet containing only 15 mEq/d of K+ during the entire 12 days of absolute bedrest. Study implications and reasons for discrepancies between K+ loss measured by balance techniques and K-42 are reviewed.

Hyatt, K. H.↗
NASA NTRS1976

Effect of thermal cycling in a Mach 0.3 burner rig on properties and structure of directionally solidified gamma/gamma prime-delta eutectic

An experimental study was carried out to evaluate the effect of cyclic thermal exposures on the mechanical properties of a gamma/gamma prime-delta eutectic alloy parallel to the growth direction. The alloy had a nominal composition by weight of Ni-20 Nb-6 Cr-2.5 Al and was directionally solidified at 3 cm/hr in a furnace with a thermal gradient of at least 200 C/cm. Bars of the alloy were exposed in a Mach 0.3 burner rig and cycled 300 times between 1100 and 425 C. Oxidation-erosion characteristics of the alloy were determined by weight loss measurements at 300-cycle intervals. After cyclic exposure, stress rupture and tensile tests were performed at both 760 and 1040 C. Microstructural changes from cyclic exposure were determined. Thermal cycling resulted in gamma prime coarsening and Widmanstaetten delta precipitation in the gamma phase. An unidentified precipitate, presumably gamma prime, was observed within the delta phase. These microstructural changes did not affect the mechanical properties of the eutectic. High oxidation-erosion weight loss rate was observed.

Gray, H. R.↗
NASA NTRS1977

Full-scale altitude engine test of a turbofan exhaust-gas-forced mixer to reduce thrust specific fuel consumption

The specific fuel consumption of a low-bypass-ratio, confluent-flow, turbofan engine was measured with and without a mixer installed. Tests were conducted for flight Mach numbers from 0.3 to 1.4 and altitudes from 10,670 to 14,630 meters (35,000 to 48,000 ft) for core-stream-to-fan-stream temperature ratios of 2.0 and 2.5 and mixing-length-to-diameter ratios of 0.95 and 1.74. For these test conditions, the reduction in specific fuel consumption varied from 2.5 percent to 4.0 percent. Pressure loss measurements as well as temperature and pressure surveys at the mixer inlet, the mixer exit, and the nozzle inlet were made.

Cullom, R. R.↗
NASA NTRS1982

Direct measurement of transmission loss of aircraft structures using the acoustic intensity approach

A measurement technique is developed in order to obtain the sound transmission loss of an aircraft fuselage which obviates the need for the two-room transmission suite. The sound transmission paths were determined in tests on a light aircraft fuselage using a two-microphone acoustic intensity method for measuring the acoustic intensity transmitted to the interior when the fuselage was exposed to an external random incidence sound-field. The intensity transmitted through different sections of the fuselage can be estimated accurately using this new technique. Results of these tests show that the plexiglass window is the major transmission path in the high frequency range. In addition, the transmission losses through a single and a double layer window were predicted theoretically by using the Statistical Energy Analysis Model. Very good agreement is found between the predictions and the measurements.

Wang, Y. S.↗
DOE OSTI2022

Adiabatic and isothermal configurations for Re 4 Si 7 transverse thermoelectric power generators

We report that transverse thermoelectric generators (TTEGs) have the potential to overcome two challenging problems that limit the commercial application of classical thermoelectric generators (TEGs): the significant irreversible efficiency losses in the contacts and the thermal degradation of the contacts at the hot end. TTEGs are built from a single material that can generate a thermoelectric current in a direction that is orthogonal to a temperature gradient. They only require a single set of contacts that are displaced away from the hot end. Here, we experimentally explore the device design considerations for optimizing the performance of this far less explored class of thermal-to-electric generation devices. We fabricate Re 4 Si 7 TTEGs and show that there is no measurable loss in efficiency with a single set of contacts that are midway between the hot and cold ends. We show that a new effect must be considered: the appearance of transverse thermal gradients that lead to significant differences between the performance of TTEGs implemented in isothermal and adiabatic geometries. The isothermal TTEG configuration leads to much higher device efficiencies. Overall, this work highlights how different the design of TTEGs is from that of conventional TEGs and the importance of controlling the device geometry for optimum waste heat recovery.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Operando carbon corrosion measurements in fuel cells using boron-doped carbon supports

Carbonaceous materials are the most common catalyst supports in proton exchange membrane fuel cell (PEMFCs), yet their corrosion is one of the limiting factors in achieving high durability. Herein, we doped carbon supports with boron (B) to increase the corrosion-resistance of the support. Two types of B-doped carbons were synthesized and studied as platinum support materials. Further, they varied in their morphologies, surface areas, and the types of boron species. The durability of Pt/B-doped carbon catalysts was investigated using the US-DOE catalysts’ supports accelerated stress test (AST) and a mass-spectrometer connected to the fuel cell effluent stream to quantify the mass of corroded carbon support in operando. The addition of boron to the carbon increased the stability of Pt catalysts in long-term usage of PEMFC. After 4000 AST cycles, more than 50% of initial current density was preserved for the boron-containing systems, while less than 30% of it remained with Vulcan carbon (Pt/V). Also, the Pt/B-doped carbon samples demonstrated better electrochemical active surface area (ECSA) stability when compared to Pt/V. Carbon loss measurements showed that B-doped carbons have higher resistance to electrochemical corrosion than unmodified carbon. Specifically, the substitutional boron-doped carbon demonstrated an extremely high stability and low corrosion rate.

25 ENERGY STORAGE↗
DOE OSTI2025

Strategy for Direct Detection of Chiral Phonons with Phase-Structured Free Electrons

Chiral phonons possessing valley pseudoangular momentum (PAM) underlie a diversity of quantum phenomena of fundamental and applied importance, but are challenging to probe directly. We show that deficiencies of typical momentum-resolved electron energy loss measurements that make it impossible to distinguish the PAM of chiral phonons can be overcome by introducing pinwheel free electron states with well-defined PAM. Transitions between such states generate 2D periodic arrays of in-plane field vortices with polarization textures tailored to selectively couple to desired chiral mode symmetries.

chirality↗
DOE OSTI2026

SPRUCE FT-ICR MS, Bulk Chemistry, and Mass Loss from Litter Decomposition Study in Experimental Plots, Marcell Experimental Forest, Minnesota, 2015-2017

This dataset contains molecular, bulk chemical, and mass loss measurements from a litter decomposition study at the Spruce and Peatland Responses Under Changing Environments (SPRUCE) experimental site within the Marcell Experimental Forest in northern Minnesota, USA. This site is in a Sphagnum spp. ombrotrophic bog forest. Litterbags were deployed into the peat in September 2015 across three warming levels (+0, +4.5, and +9°C) under ambient and elevated carbon dioxide (CO₂ - +500 ppm) and retrieved after roughly 0.5, 1, and 2 years of field incubation (2015-09-23 to 2017-08-02). Litterbags containing six peatland litter types: black spruce needles (Picea mariana - SPL), spruce fine roots (SPR), Sphagnum angustifolium (ANG), Sphagnum magellanicum (MAG), Labrador tea leaves (Rhododendron groenlandicum - LTL), and Labrador tea roots (LTR). Molecular composition of water-soluble organic matter extracts was characterized using Fourier Transform Ion Cyclotron Resonance Mass Spectrometry (FT-ICR MS) at 9.4 Tesla, operated in negative ion mode with electrospray ionization, providing molecular formula assignments and compound-class distributions across the decomposition time series. Bulk chemical characterization included elemental analysis (percent carbon, nitrogen, and phosphorus) and Fourier Transform Infrared Spectroscopy (FTIR) to quantify functional group composition. Litter mass loss was tracked gravimetrically at each retrieval interval, expressed as percent mass remaining relative to initial dry mass for each litter type and treatment combination. These data are valuable for understanding how vegetation shifts driven by increased atmospheric CO2 and temperature in peatlands alter litter inputs and organic matter stabilization trajectories, with implications for projecting and modeling peatland carbon cycling. This dataset contains two data files in comma-separated value (.csv) format. Additional metadata are provided: two data dictionaries and a file-level metadata file in comma separate (.csv) format and a user guide in PDF (*.pdf) format.

decomposition↗
DOE OSTI2022

Castanha et al. 2018: Hopland Lysimeter 13C-Labeled Root Litter Decomposition Study.

The breakdown and decomposition of plant inputs are critical for nutrient cycling, soil development, and climate-ecosystem feedbacks, but uncertainties persist in how the rates and products of litter decomposition are affected by soil temperature, rhizosphere, and depth of input. To elucidate these questions we measured the effects of soil warming (+ 4 °C), rhizosphere, and depth of litter placement on the decomposition of Avena fatua (wild oat grass) root litter in a Mediterranean grassland ecosystem. Field lysimeters were subjected to three environmental treatments (heating, control, and plant removal) and three 13C-labeled root litter addition treatments (to A horizon, to B horizon, and no-addition disturbance control) for each of two harvest time points. We buried root litter in February 2014 and measured loss of 13C in CO2 from the soil surface and in leachate as dissolved organic carbon (DOC) over two growing seasons. At the end of each of the 2014 and 2015 growing seasons we recovered the 13C remaining in the soil. Loss of root litter C occurred almost entirely via heterotrophic respiration, with an estimated < 2% lost as DOC during the initial decay period. The added roots were broken down and incorporated into bulk soil material very quickly; only ~ 30% of added root was visible after 6 months. In the first growing season, decomposition occurred faster in the B than in the A horizon, the latter having greater moisture limitation. Subsequently, there was almost no further decomposition in the B horizon. After two growing seasons, less than 20% of the added root litter C remained in the A or B horizons of all environmental treatments. Heating did not stimulate decomposition, likely because it exacerbated the moisture limitation. However, while plots without plants dried down more slowly than plots with plants, their decomposition rate was not significantly greater, possibly due to the lack of rhizosphere processes such as priming. We conclude that in this Mediterranean grassland ecosystem, soil moisture, which is affected by season, depth, heating, and rhizosphere, plays a dominant role in mediating the effect of those factors on root litter decomposition, which after two seasons did not differ by depth or by treatment.The files in this dataset comprise (1) 13C-labeled litter additions made to each plot, (2) litter recovery after each of 2 growing seasons, (3) periodical soil flux measurements, (4) leachate measurements, and continuously monitored soil (5) temperature and (6) moisture.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

How Wrong Can the Operational AEP Uncertainty Estimate Be When We Ignore the Correlations Between the Uncertainty Components?

Calculations of wind farm annual energy production (AEP) on operational data are essential for a variety of financial transactions during the life of wind plants. The AEP estimate is associated with an uncertainty value, which is calculated by combining contributions connected to on-site measurements, long-term reference measurements, losses, regression, windiness adjustment, and wind resource interannual variability. Although very limited documentation on the topic exists, the conventional approach currently used by the wind energy community to assess the uncertainty connected to the operational AEP estimate assume that the different uncertainty components are uncorrelated and therefore calculates the overall uncertainty with a sum of squares approach. In this analysis, we contrast the traditional technique to estimate the overall AEP uncertainty by ignoring the correlation between its different components with a novel Monte Carlo based approach, which can instead take into account the correlation between different uncertainty categories. We consider monthly operational data from 472 wind farms from the Energy Information Administration (EIA) 923 database to assess the difference between the two approaches. Long-term wind speed data needed for the AEP assessment are taken from three reanalysis products: the Modern-Era Retrospective analysis for Research and Applications v2 (MERRA-2), the European Reanalysis Interim (ERA-interim), and the National Centers for Environmental Prediction v2 (NCEP-2). The results of the Monte Carlo approach show that three pairs of AEP uncertainty components do show a statistically significant correlation: the uncertainty connected with wind resource inter-annual variability is positively correlated with the one related to the windiness correction and negatively correlated with the one due to the regression, and the wind measurement uncertainty is positively correlated with the regression uncertainty. All these correlations, which are found between uncertainty components which are not only part of an operational analysis, but also of a wind resource assessment, are currently ignored in the conventional techniques used as industry standard. We further investigate the causes of these correlations, in terms of common dependencies of different uncertainty components on wind resource variability, number of data points, and quality of the regression between wind speed and energy production data. Next, we quantify the error in the current industry standard technique, in terms of the percentage difference in total uncertainty calculated with the two considered approaches, for all the analyzed wind farms. We find a mean absolute percentage difference of about 6%, with the largest differences being greater than 20%. The data clearly confirm that ignoring the actual correlation between the uncertainty components can lead to large errors in the assessment of the operational AEP uncertainty, and the proposed Monte Carlo approach should be preferred.

Monte Carlo↗
DOE OSTI2021

Transparent Refractory Aerogels for Efficient Spectral Control in High–Temperature Solar Power Generation

Although spectrally selective materials play a key role in existing and emerging solar thermal technologies, temperature-related degradation currently limits their use to below 700 °C in vacuum and even lower temperatures in air. Here a solar-transparent refractory aerogel that offers stable performance up to 800 °C in air is demonstrated, which is significantly greater than its silica counterpart. This improved stability is attributed to the formation of a refractory aluminum silicate phase, which is synthesized using a conformal single cycle of atomic layer deposition within the high-aspect-ratio pores of silica aerogels. Furthermore, based on direct heat loss measurements, the transparent refractory aerogel achieves a receiver efficiency of 75% at 100 suns and an absorber temperature of 700 °C, which is a 5% improvement over the state of the art. Transparent refractory aerogels may find widespread applicability in solar thermal technologies by enabling the use of lower-cost optical focusing systems and eliminating the need for highly evacuated receivers. In particular, a shift to higher operating temperatures while maintaining a high receiver efficiency can enable the use of advanced supercritical CO 2 power cycles and ultimately translate to an ≈10% (absolute) improvement in solar-to-electrical conversion efficiency relative to existing linear concentrating systems.

14 SOLAR ENERGY↗
DOE OSTI2021

Effect of Water Vapor on Lifetime of 625 and 120 Foils During Oxidation Between 650 and 800 °C

In this work, the oxidation behavior of alloy 625 and 120 foils was studied at 650, 700 and 800 °C in dry air and flowing air + 10% H 2 O up to 10,000 h (alloy 625) or 30,000 h (alloy 120). The effect of water vapor on Cr loss was investigated. Manganese and iron in the 120 foil induced faster Cr depletion in the foil and breakdown of the Cr 2 O 3 scale into Fe and Cr-rich oxide compared to the alloy 625 foil. In the latter case, the presence of Nb led to the formation of Nb and Cr-rich oxide after breakdown of the Cr 2 O 3 scale. Simultaneous Cr loss due to oxidation and volatilization of the Cr 2 O 3 oxide scale was predicted and compared to experimental Cr loss measurements for exposures up to 30,000 h.

36 MATERIALS SCIENCE↗