Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lithium dendrite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Rapid charging made practical in graphite-based lithium batteries: surface-acoustic wave turbulent electrolyte mixing to overcome diffusion limited charging rates [Final Report]

One of the key limits in rapidly recharging a lithium-ion battery is the depletion of lithium ions within the electrolyte adjacent the anode during charging and long diffusion time to overcome this depletion. It also causes dendrite formation, inefficient use of the lithium, and battery degradation over many charge-discharge cycles. Because the liquid electrolyte remains quiescent and unmixed, this depletion layer’s depth rapidly grows to match the anode-cathode separation distance at even modest charge rates. The solution proposed by PI Prof. James Friend and Co-PI Prof. Ping Liu, both from the University of California, San Diego, is to mix the electrolyte and minimize the Li+ ion concentration gradient during charging. Even in the presence of the separator, the charging rate could then be significantly increased. They propose to accomplish this using surface acoustic wave (SAW)-driven acoustic streaming, a technique employing 10-mW fingernail-sized solid-state devices from the telecommunications industry to drive turbulent mixing to submicron length scales in a manner completely compatible with the typical 20700 and 18650 cells used in electric vehicles. 0.1. Turbulent acoustic streaming mixes the electrolyte during charging—even with separator Our proposed 100-MHz SAW device used to recirculate the electrolyte is compatible with lithium- ion battery electrochemistry, as it is made in our lab of single-crystal lithium niobate. Their solution is straightforward to drive from a DC power source alongside the signal provided during battery charging. The device is only needed during charging and does not consume power dur- ing battery discharge. Uniquely, SAW generates extreme accelerations of over 1 billion meters per second squared in the fluid, driving turbulent mixing from centimeter to submicron length scales, even through the porous separator materials that tend to be used in batteries, all while avoiding interfering with the anode’s solid electrolyte interphase layer that forms during use. By employing novel fluid mechanics, the investigators are proposing a new direction for battery research away from direct use of materials science and electrochemistry. The chemistry agnostic solution may be employed in any battery chemistry that makes use of liquid electrolytes, providing a broader transformative benefit to the battery research community. They are to produce a series of prismatic and 20700-cell sized 2 Ah batteries capable of being charged and discharged at least 500 times without more than 20% loss in battery capacity, and to provide analysis tools useful to the battery research and development community for adopting this approach for other battery chemistries and configurations.

25 ENERGY STORAGE↗
DOE OSTI2020

Enabling High Capacity and Coulombic Efficiency for Li-NCM811 Cells Using a Highly Concentrated Electrolyte

Lithium metal batteries suffer from dendrite formation and the associated safety hazards of thermal runaway reactions. In this study, we report the performances of a highly concentrated electrolyte (HCE) and a dilute LiPF6 electrolyte in lithium metal cells using LiNi 0.8 Co 0.1 Mn0.1O 2 . While the HCE exhibits lower bulk ionic conductivity than the dilute LiPF6 electrolyte, the cell conductivity is higher for the HCE system, indicating higher thermodynamic stability of the electrolyte against the electrodes. Full cell cycling demonstrates higher capacity for the HCE system, which declines as a function of cycle number due to the formation of decomposition products, similar to the dilute LiPF 6 system. The origin of the enhanced performance is the higher stability of the HCE against a Li metal anode as compared to the dilute LiPF 6 electrolyte. Cycling at higher temperatures further enhances the performance of the HCE, which is more thermally stable than the dilute LiPF 6 electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2023

Probing lithium mobility at a solid electrolyte surface

Abstract Solid-state electrolytes overcome many challenges of present-day lithium ion batteries, such as safety hazards and dendrite formation 1,2 . However, detailed understanding of the involved lithium dynamics is missing due to a lack of in operando measurements with chemical and interfacial specificity. Here we investigate a prototypical solid-state electrolyte using linear and nonlinear extreme-ultraviolet spectroscopies. Leveraging the surface sensitivity of extreme-ultraviolet-second-harmonic-generation spectroscopy, we obtained a direct spectral signature of surface lithium ions, showing a distinct blueshift relative to bulk absorption spectra. First-principles simulations attributed the shift to transitions from the lithium 1 s state to hybridized Li- s /Ti- d orbitals at the surface. Our calculations further suggest a reduction in lithium interfacial mobility due to suppressed low-frequency rattling modes, which is the fundamental origin of the large interfacial resistance in this material. Our findings pave the way for new optimization strategies to develop these electrochemical devices via interfacial engineering of lithium ions.

25 ENERGY STORAGE↗
DOE OSTI2020

A disordered rock salt anode for fast-charging lithium-ion batteries

Rechargeable lithium-ion batteries with high energy density that can be safely charged and discharged at high rates are desirable for electrified transportation and other applications. However, the sub-optimal intercalation potentials of current anodes result in a trade-off between energy density, power and safety. In this paper we report that disordered rock salt Li 3+ x V 2 O 5 can be used as a fast-charging anode that can reversibly cycle two lithium ions at an average voltage of about 0.6 volts versus a Li/Li + reference electrode. The increased potential compared to graphite reduces the likelihood of lithium metal plating if proper charging controls are used, alleviating a major safety concern (short-circuiting related to Li dendrite growth). In addition, a lithium-ion battery with a disordered rock salt Li 3 V 2 O 5 anode yields a cell voltage much higher than does a battery using a commercial fast-charging lithium titanate anode or other intercalation anode candidates (Li 3 VO 4 and LiV 0.5 Ti 0.5 S 2 ). Further, disordered rock salt Li 3 V 2 O 5 can perform over 1,000 charge–discharge cycles with negligible capacity decay and exhibits exceptional rate capability, delivering over 40 per cent of its capacity in 20 seconds. We attribute the low voltage and high rate capability of disordered rock salt Li 3 V 2 O 5 to a redistributive lithium intercalation mechanism with low energy barriers revealed via ab initio calculations. This low-potential, high-rate intercalation reaction can be used to identify other metal oxide anodes for fast-charging, long-life lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

In Situ Formation of Polycyclic Aromatic Hydrocarbons as an Artificial Hybrid Layer for Lithium Metal Anodes

Nonuniform Li deposition causes dendrites and low Coulombic efficiency (CE), seriously hindering the practical applications of Li metal. Herein, we developed an artificial solid-state interphase (SEI) with planar polycyclic aromatic hydrocarbons (PAHs) on the surface of Li metal anodes by a facile in situ formation technology. The resultant dihydroxyviolanthron (DHV) layers serve as the protective layer to stabilize the SEI. In addition, the oxygen-containing functional groups in the soft and conformal SEI film can regulate the diffusion and transport of Li ions to homogenize the deposition of Li metal. The artificial SEI significantly improves the CEs and shows superior cyclability of over 1000 h at 4 mAh cm –2 . The LiFePO 4 /Li cell (2.8 mAh cm –2 ) enables a long cyclability for 300 cycles and high CEs of 99.8%. Furthermore, this work offers a new strategy to inhibit Li dendrite growth and enlightens the design on stable SEI for metal anodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Electrospun Separator Based on Sulfonated Polyoxadiazole with Outstanding Thermal Stability and Electrochemical Properties for Lithium-Ion Batteries

Traditional polyolefin separators used in lithium-ion batteries (LIBs) are seriously limited by the issues of inferior security and poor electrolyte wettability. Most of the very promising candidate separators based on heat-resistant polymers are, however, inherently difficult to process. Herein, a unique sulfonated aromatic heterocyclic polymer, lithiated poly(diphenyl ether oxadiazole) sulfonate (Li-SPEOD), was synthesized through a simple one-pot method and further electrospun to act as a novel separator (es-Li-SPEOD) for LIBs. In this work, the prepared Li-SPEOD possesses a high degree of sulfonation with a high molecular weight (M w = 4.31 × 10 5 ). The es-Li-SPEOD separator exhibits excellent mechanical and fire-resistance properties and is able to maintain dimensional stability at a temperature of even up to 400 °C in air. The ionic conductivity (3.57 mS cm –1 ) and lithium-ion transference number (0.37) of the es-Li-SPEOD with an electrochemical stability window of 4.5 V vs Li + /Li can be improved by 382.4 and 32.1%, respectively, compared to those of Celgard-2500 in the LiPF 6 electrolyte. The enhanced rate capability and cycle performance of the LiFePO 4 –Li half-cell are therefore obtained. Moreover, the es-Li-SPEOD displays an outstanding dendrite-suppressing effect for the lithium metal anode. This research proves that the Li-SPEOD-based separator has a broad application perspective in next-generation lithium batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Composite Lithium Metal Structure to Mitigate Pulverization and Enable Long‐Life Batteries

In lithium metal batteries, non‐uniform stripping of lithium results in pit formation, which promotes subsequent non‐uniform, dendritic deposition. This viscous cycle leads to pulverization of lithium which promotes cell shorting or capacity degradation, symptoms further exaggerated by high electrode areal loading and lean electrolytes. Here, to address this challenge, a composite lithium metal anode is engineered that contains uniformly distributed, nanometer‐sized carbon particles. This composite lithium is shown to strip more uniformly since the growth of non‐uniform pits is intercepted by the carbon particles. This mechanism is corroborated by a continuum electrochemical model. Subsequent lithium deposition on carbon particles is also found to be more uniform than on the surface with irregular pits. Notably, the pulverization rate of composite lithium is 26 times slower than that of commercial lithium. Moreover, in a Li‐S battery with sulfurized polyacrylonitrile cathode, the use of the composite anode extends the cycle life by three times when the areal capacity is 8 mAh cm −2 . The approach of using an engineered lithium composite structure to address challenges during both stripping and plating can inform future designs of lithium metal anodes for high areal capacity operations.

high areal capacity↗
DOE OSTI2021

Practical Considerations for Testing Polymer Electrolytes for High-Energy Solid-State Batteries

Polymer electrolytes are an important class of materials in enabling solid-state batteries, which have the potential to exceed 400 Wh/kg energy density. Despite significant advancements in their lithium-ion transport and mechanical properties over the last two decades, the integration and testing of these novel electrolyte materials into functioning cells with the electrode loadings and dimensions required to meet the cell-level energy density goals have been limited. Here, through multiple representative examples, we demonstrate the need of testing in close to practical cell conditions for a faster and more reliable evaluation of polymeric electrolytes. In particular, the need for testing with thin lithium anodes and practical cycling capacities is demonstrated for evaluation of their lithium-metal interfacial stability and dendritic resistance, respectively, and a testing protocol is suggested. The guidelines presented here will also apply to testing of other solid electrolytes for solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Harnessing Electrochemical‐Mechanical Couplings to Improve the Reliability of Solid‐State Batteries

Abstract One key barrier to using lithium‐metal anode batteries is that metal dendrites can penetrate solid electrolytes, causing short‐circuits and battery failures. It is established that this failure is likely caused by crack propagation due to electrodeposition‐induced stresses from lithium metal. This study explores ways to harness these electrochemical‐mechanical couplings to control dendrite growth and improve battery reliability using a phase‐field model and targeted fracture experiments. The results show that dendrite growth can be effectively mitigated by applying mechanical stresses or tailoring the material's fracture toughness. This study also outlines the requirements for compressive stress to halt or deflect dendrites as a function of the overpotential and discusses the role of microstructure in this process.

Monismith, Scott↗
DOE OSTI2025

Reactive Suspension Electrolytes for Lithium Metal Batteries

Lithium metal batteries (LMBs) suffer from dendrite growth and capacity loss, which compromise safety and cycle life. Here, we present a simple reactive suspension electrolyte (RSE) strategy. When metal oxide (MO x ) nanoparticles are dispersed in the liquid electrolyte, in situ formation of Li 2 O and Li–M phases occurs at the lithium metal anode. By studying two different types of RSEs, Type 1 RSEs (i.e., CuO RSE) without metal-Li alloying and Type 2 RSEs (i.e., ZnO RSE and In 2 O 3 RSE) with metal-Li alloying capability, we elucidate the roles of each reaction compound. Here, we find that Li 2 O can improve reversibility of Li metal anode by stabilizing the interphase while Li–M alloy phases guide uniform Li metal plating. Compared to the carbonate-type reference electrolyte, RSEs demonstrate reduced nucleation overpotential, lower interfacial impedance, and higher Coulombic efficiency, leading to an extended cycle life in Li|Li 1 Ni 0.8 Co 0.1 Mn 0.1 O 2 full cells.

Lee, Junyoung [Stanford Univ., CA (United States)]↗
DOE OSTI2022

High-performance all-solid-state Li–S batteries enabled by an all-electrochem-active prelithiated Si anode

The development of all-solid-state Li–S batteries has been greatly impeded by dendrite growth and dendrite penetration, which are both related to the Li metal anode. As a compromised alternative, we report lithium silicide (Li x Si) as a dendrite-free and high-capacity anode with Li source. Here, the as-synthesized Li x Si is relatively soft, highly electronically conductive, and with a high Li diffusivity. These distinctive properties make Li x Si anode viable as an “all-electrochem-active” electrode (consisted of 100 wt.% Li x Si). Compared with the typical composite electrode, the all-electrochem-active electrode not merely maximizes the electrode-level energy density but also minimizes the electrolyte-related interfacial degradation. Li x Si symmetric cell demonstrates a reversible cycling at 4 mA cm –2 for over 320 h. Stress change and morphological evolution of the Li x Si electrode are investigated upon dealloying/alloying. When paired with a S cathode (active mass loading of 3 mg cm –2 ), Li x Si–S full cell shows a good cycling behavior over 500 cycles and rate performance (69% capacity retained at 1.2C) even at 25 °C.

25 ENERGY STORAGE↗
DOE OSTI2021

In situ formation of polymer-inorganic solid-electrolyte interphase for stable polymeric solid-state lithium-metal batteries

Composite polymer electrolytes (CPEs) for solid-state Li-metal batteries (SSLBs) still suffer from gradually increased interface resistance and unconstrained Li-dendrite growth. Herein, we addressed the challenges by designing a LiF-rich inorganic solid-electrolyte interphase (SEI) through introducing a fluoride-salt-concentrated interlayer on CPE film. The rigid but flexible CPE helps accommodate the volume change of electrodes, while the polymeric highly concentrated electrolyte (PHCE) surface-layer regulates Li-ion flux due to the formation of a stable LiF-rich SEI via anion reduction. The designed CPE-PHCE presents enhanced ionic conductivity and high oxidation stability of >5.0 V (versus Li/Li + ). Furthermore, it dramatically reduces the interfacial resistance and achieves a high critical current density of 4.5 mA cm –2 . The SSLBs, fabricated with thin CPE-PHCE membranes (<100 μm) and Co-free LiNiO 2 cathodes, exhibit exceptional electrochemical performance and long cycling stability. Lastly, this approach of SEI design can also be applied to other types of batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Stress engineering for crack and dendrite prevention in solid electrolytes via ion implantation

Solid-state batteries represent a promising technology that offers safer and more densely packed energy storage. A primary cause of failure in solid-state cells is the penetration of metal dendrites through the solid electrolyte. Here, we report that fluorine-ion implantation can enhance the mechanical resistance of solid electrolyte Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 to dendrite propagation by inducing residual compressive stress in the subsurface of the electrolyte. Ion implantation modifies subsurface residual stress and also alters the electrolyte’s surface, resulting in multifunctional enhancement. The combined chemical and mechanical effects of ion implantation enable reversible lithium metal stripping and plating at elevated current densities while enhancing air stability and mitigating the formation of a harmful carbonate layer at the surface. This study provides new insights into a scalable dendrite-suppression strategy for designing solid-state batteries suitable for cycling at room temperature and low stack pressures.

25 ENERGY STORAGE↗
DOE OSTI2025

Pressure-Tolerant 3D Anodes Enable Short-Circuit Prevention and Low Heat Generation in Argyrodite Solid-State Batteries

Solid-state batteries (SSBs) offer a safer, higher-energy-density alternative to lithium-ion batteries, yet commercialization is hindered by incompatibility with lithium metal. Here, to overcome these challenges, we developed a cost-effective, commercially available prelithiated micro carbon fiber framework (Li-Cf) anode featuring a high-pressure-tolerance, for use with argyrodite solid-state electrolytes (SSEs). This 3D structure accommodates uniform lithium deposition, simplifies cell assembly under elevated pressure, inhibits dendrite growth toward SSEs, reduces heat generation, and enhances overall compatibility. Notably, our architecture enables the cell to tolerate pressures up to 400 MPa without short-circuiting during assembly. Meanwhile, the 3D framework serves as a preferential pathway for lithium deposition, thereby reducing lithium growth toward the SSEs and mitigating the risk of dendrite formation in SSEs. Operando calorimetry and distribution of relaxation times analysis reveal that lithium morphology degradation at the interface with the SSEs is a key failure mechanism in lithium metal argyrodite SSBs, leading to increased diffusion resistance and heat generation. In contrast, the Li-Cf anode mitigates these issues by reducing both heat flux and charge transfer resistance. Full cells with LiNi 0.8 Co 0.1 Mn 0.1 O 2 /Li 6 PS 5 Cl/Li-Cf retain ~79% capacity after 600 cycles, demonstrating significantly improved cycling stability and strong potential for practical energy storage applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Potentiometric entropy and operando calorimetric measurements reveal fast charging mechanisms in PNb 9 O 25

The Wadsley–Roth compound PNb 9 O 25 is a promising fast charging lithium ion battery anode material with high operating voltage to prevent solid electrolyte interface formation. Here, in this work, we present potentiometric entropy measurements featuring signatures of semiconductor-to-metal transition and intralayer ordering upon lithiation in the anode material PNb 9 O 25 that could not be observed with in situ X-ray diffraction. In addition, the instantaneous heat generation rates at the PNb 9 O 25 working electrode and at the lithium metal counter electrode during galvanostatic cycling were measured individually for the first time by operando isothermal calorimetry. The heat generation rate decreased at the PNb 9 O 25 electrode upon lithiation due to the decrease in electrical resistivity caused by the semiconductor-to-metal transition observed in potentiometric entropy measurements. Furthermore, the heat generation rate at the lithium metal electrode was positive during delithiation due to the exothermic plating of Li + ions on the lithium metal counter electrode associated with dendrite formation. Furthermore, calorimetric measurements established that the entropy change dominated the reversible heat generation rate at each electrode. Finally, the contribution of enthalpy of mixing was relatively small even at high C-rates thanks to the high Li + ion mobility in PNb 9 O 25 confirming its promises as a fast charging anode material.

25 ENERGY STORAGE↗
DOE OSTI2020

Tuning the Anode–Electrolyte Interface Chemistry for Garnet-Based Solid-State Li Metal Batteries

Lithium (Li) metal anode is a promising candidate for high energy density solid-state batteries. However, the interface issues, including large interfacial resistance and Li dendrite generation, have always frustrated the attempt to commercialize solid-state Li metal batteries (SSLBs). Here, we report that infusing the garnet-type solid electrolytes (GSEs) with air-stable electrolyte Li 3 PO 4 (LPO) dramatically reduces the interfacial resistance to ~1 Ω cm 2 and achieves a high critical current density of 2.2 mA cm -2 under ambient condition due to enhanced interfacial stability to Li metal anode. The coated and infused LPO electrolytes not only improve the mechanical strength and Li-ion conductivity of grain boundaries, but also form a stable Li-ion conductive but electron-insulating LPO-derived solid-electrolyte interphase between Li metal and GSEs, and consequently eliminates the Li dendrites growth and prevents the direct reduction of GSEs by Li metal over a long cycle life. This interface engineering approach together with grain-boundary modification on GSEs represents a promising strategy to revolutionize the anode-electrolyte interface chemistry for SSLBs and provides new design strategy for other-types of solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

VTO_2021_APR_LLNL_Ye

Traditional batteries are composed of two-dimensional films that are stacked and/or rolled. Thin film batteries display high power density while their thick film counterparts show good energy density, but it has proven difficult to concurrently achieve both within these planar form factors. In addition, conventional Li-ion batteries based on liquid organic electrolytes or gel polymer electrolytes have raised severe safety concerns due to the intrinsic flammable properties of the organic electrolytes. They are also not ideal for the use of high energy density metallic lithium (Li) anodes due to Li dendrite growth, or sulfur cathodes due to shuttling effects that result in fast capacity fade. There is an urgent need to develop safe, high-performance solid-state batteries (SSBs) with advanced electrolyte and separator technologies. Although in recent years a series of superionic conductors have been developed for electrolytes and separators, their performance does not satisfy demanding criteria due to large impedance from poor solid electrolyte-electrode contact and questionable electrochemical and mechanical stability. Unlike the well-established roll-to-roll fabrication of conventional Li-ion batteries, the processing of SSBs is unique due to the brittleness of solid-state electrolytes (SSEs). The commercially available or lab-developed SSE discs are usually very thick (hundreds of micrometers to millimeters) to overcome their brittle nature, which unfortunately increases the cell impedance and accounts for the majority of the overall cell weight and volume, leading to dramatically decreased power and energy densities. In this project, we will investigate 3D printing techniques to overcome safety, fabrication, mechanical, and electrochemical issues in SSBs. 3D printing builds complex structures in a layer-by-layer fashion, which allows rapid production of hierarchical architectures, gradient and multi-material structures, and multi-component assemblies. 3D printing is an emerging area that could fundamentally transform energy storage devices. For example, 3D printing can produce batteries with arbitrary form factors to fit a product’s specific volume requirements and can create interwoven electrode arrangements over a wide range of length scales to improve transport and increase power density for a given energy density. For SSBs, 3D printing may dramatically reduce the separator thickness from ~1 mm (by hydraulic pressing) to tens of micrometers or less. In addition, the interfacial contact area between the electrolyte and the electrode may be increased via 3D interdigitated designs. Hence, we expect a significant reduction of the overall cell impedance and enhancement of both energy and power densities of SSBs by harnessing an array of 3D printing technologies being developed at Lawrence Livermore National Laboratory (LLNL).

25 ENERGY STORAGE↗
DOE OSTI2025

Mitigating Battery Cell Failure: Role of Ag‐Nanoparticle Fillers in Solid Electrolyte Dendrite Suppression

Abstract The development of solid‐state batteries (SSBs) with lithium Li metal anodes holds significant promise for enhancing the energy density and safety of next‐generation energy storage systems. However, their commercialization is hindered by challenges related to Li dendrite formation, which can lead to short circuits and battery failure. In this study, the role of Ag nanoparticles embedded within solid electrolytes (SE) is investigated in suppressing dendrite propagation. The results demonstrate that Ag nanoparticles effectively mitigate two key failure mechanisms: (1) dendrite growth within porous networks at low current densities and (2) stress intensification‐induced SE fracture at higher current densities (12 mA cm −2 ). Ex situ characterization using focused‐ion beam – scanning electron microscopy (FIB–SEM) and energy dispersive X‐ray spectroscopy (EDS,) reveals that Ag nanoparticles migrate alongside advancing Li dendrites, promoting homogeneous dendrite growth and reducing the likelihood of localized stress concentrations. Additionally, the incorporation of Ag nanoparticles is shown to facilitate a more uniform Li distribution toward the anode side, which can potentially enable the use of higher charging rates in SSBs. This study provides a new perspective on Li dendrite suppression and presents new opportunities for enhancing the performance and safety of SSBs.

Diallo, Mouhamad Said↗