Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “layup”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

The structural behavior of a graphite-polymide honeycomb sandwich panel with quasi-isotropic face sheets and an orthotropic core

The results of a series of tests of graphite-polyimide honeycomb sandwich panels are presented. The panels were 1.22 m long, 0.508 m wide, and approximately 13.3 m thick. The face sheets were a T-300/PMR-15 fabric in a quasi-isotropic layup and were 0.279 mm thick. The core was Hexcel HRH 327-3/16 - 4.0 glass reinforced polyimide honeycomb, 12.7 mm thick. Three panels were used in the test: one was cut into smaller pieces for testing as beam, compression, and shear specimens; a second panel was used for plate bending tests; the third panel was used for in-plane stability tests. Presented are the experimental results of four point bending tests, short block compression tests, core transverse shear modulus, three point bending tests, vibration tests, plate bending tests, and panel stability tests. The results of the first three tests are used to predict the results of some of the other tests. The predictions and experimental results are compared, and the agreement is quite good.

Hyer, M. W.↗
NASA NTRS1980

Mechanisms of fatigue damage in boron/aluminum composites

Tensile fatigue tests were conducted on several laminates of boron/aluminum (6061-0). In laminates with 0 deg fibers on the outside, an analysis that identifies "shakedown" conditions predicted the stress amplitude below which no fatigue damage accumulated. A fatigue damage accumulation model which relates matrix fatigue cracking and the overall laminate properties is described. A model for the saturation damage stage development is presented, that identical laminates, tested in directions 90 deg apart (such that one layup has 90 deg outer plies and the other 0 deg), have different fatigue behaviors due to the stacking sequence. The 90 deg plies on the surface develop cracks earlier than predicted by shakedown. An attempt was made to explain this stacking sequence effect. Variable load history effects on the fatigue damage response were investigated. Tests reveal that for a given stress ratio the specimen seeks the saturation damage state for the largest stress range to which it is subjected. It was also found that little damage is generated by shifting a given stress range down, whereas significant damage may be created by shifting it upward. The laminate stresses were always tensile.

Johnson, W. S.↗
NASA NTRS1981

Fatigue degradation in compressively loaded composite laminates

The effect of imbedded delaminations on the compression fatigue behavior of quasi-isotropic, T300/5208, graphite/epoxy laminates was investigated. Teflon imbedments were introduced during panel layup to create delaminations. Static and constant amplitude (R=10, omega = 10 Hz) fatigue tests were conducted. S-N data and half life residual strength data were obtained. During static compression loading, the maximum deflection of the buckled delaminated region was recorded. Under compression fatigue, growth of the imbedded delamination was identified as the predominant failure mode in most of the test cases. Specimens that exhibited others failures had a single low stiffness ply above the Teflon imbedment. Delamination growth during fatigue was monitored using DIB enhanced radiography. In specimens with buried delaminations, the dye penetrant (DIB) was introduced into the delaminated region through a minute laser drilled hole, using a hypodermic needle. A low kV, microfocus, X-ray unit was mounted near the test equipment to efficiently record the cyclic growth of buried delaminations on Polaroid film.

Ramkumar, R. L.↗
NASA NTRS1981

Tackifier for addition polyimides containing monoethylphthalate

An improvement of addition polyimides wherein an essentially solventless, high viscosity laminating resin is synthesized from low cost liquid monomers is disclosed. The improved process takes advantage of a reactive, liquid plasticizer such as monoethylphthalate (MEP) which is used in lieu of an alcohol solvent, and helps solve a major problem of maintaining good prepreg tack and drape, or the ability of the prepreg to adhere to adjacent plies and conform to a desired shape during the layup process. This improvement results in both longer life of the polymer prepreg and the processing of low void laminate and appears to be applicable to all addition polyimide systems.

St.clair, T. L.↗
NASA NTRS1981

Buckling of composite cylinders under combined compression and torsion Theoretical/experimental correlation

Elastic buckling loads for laminated composite circular cylindrical shells under combined axial compression and torsion are plotted on a dimensionless load plane and determined experimentally from boron/epoxy and graphite/epoxy specimens with symmetric and asymmetric layups. Good correlation is achieved between the theoretical and experimental interaction curves. The theoretical buckling loads are obtained from Fluegge's cylindrical shell equations and for pure torsion there is good correlation, but for the pure axial compression the correlation is rather poor.

Herakovich, C. T.↗
NASA NTRS1980

Thermal deformations and stresses in composite materials

Residual stresses are induced during curing in angle-ply laminates as a result of anisotropic thermal deformations of the variously oriented plies. Residual strains are measured experimentally using embedded strain gage techniques, and residual stresses are computed using orthotropic stress-strain relations. The results show that, for graphite and Kevlar laminates, residual stresses at room temperature are high enough to cause damage in the plies in the transverse to the fiber direction. It is also shown that residual stresses do not relax appreciably. The ply stacking sequence is found to have no effect on the magnitude of average residual stresses. Residual stresses and susceptibility to cracking during curing depend to a marked extent on ply layup.

Daniel, I. M.↗
NASA NTRS1981

Fabrication of titanium multiwall Thermal Protection System (TPS) curved panel

A method is described for fabricating curved T1-6Al-4V multiwall panels having a single radius of curvature of 30.5 cm (12 inches). A panel 30.5 x 30.5 x 1.7 cm (12 x 12 x .688 inch) having 4 dimpled sheets, 5 undimpled sheets, and stepped side closures was designed, fabricated and delivered for evaluation. Tool design for skin and dimpled sheet forming are described as well as layup and liquid interface diffusion bonding.

Blair, W.↗
NASA NTRS1982

Equipment development for automated assembly of solar modules

Prototype equipment was developed which allows for totally automated assembly in the three major areas of module manufacture: cell stringing, encapsulant layup and cure and edge sealing. The equipment is designed to be used in conjunction with a standard Unimate 2000B industrial robot although the design is adaptable to other transport systems.

Hagerty, J. J.↗
NASA NTRS1982

Measurements of displacement around holes in composite plates subjected to quasi-static compression

Attempts to develop a whole-field, high sensitivity optical technque for measurement of load induced changes of thickness of composite plates are described. Graphite-epoxy plates of quasi-isotropic layup were used as test specimens. Changes of thickness of three plates, each with a central hole of different size, were measured as a function of applied compressive loads. The first test specimen showed localized zones where no holographic fringes were present, surrounded by zones of low fringe contrast. This was thought to be a result of localized motion or creep. Subsequent tests with an increased time interval between specimen loading and holographic exposure demonstrated no localized zones of absent fringes. No plausible explanation for radical differences in the quality of fringe patterns was found, although the use of specimens having a high quality mirrorized surface provided superior change of thickness patterns. Recommendations for further investigations and changes in test procedure are presented.

Duke, J. C., Jr.↗
NASA NTRS1982

Tensile stress-strain behavior of graphite/epoxy laminates

The tensile stress-strain behavior of a variety of graphite/epoxy laminates was examined. Longitudinal and transverse specimens from eleven different layups were monotonically loaded in tension to failure. Ultimate strength, ultimate strain, and strss-strain curves wee obtained from four replicate tests in each case. Polynominal equations were fitted by the method of least squares to the stress-strain data to determine average curves. Values of Young's modulus and Poisson's ratio, derived from polynomial coefficients, were compared with laminate analysis results. While the polynomials appeared to accurately fit the stress-strain data in most cases, the use of polynomial coefficients to calculate elastic moduli appeared to be of questionable value in cases involving sharp changes in the slope of the stress-strain data or extensive scatter.

Garber, D. P.↗
NASA NTRS1982

Requirements and design of the graphite/epoxy structural elements for the optical telescope assembly of the space telescope

The production of the Space Telescope's Metering Truss Structure (MTS) and Focal Plane Structure (FPS), which are of graphite/epoxy, is described. Graphite/epoxy laminates were chosen because of their high strength and stiffness, low weight, and a controlled coefficient of thermal expansion approaching zero. Photocopy masters, which are dimensionally accurate and stable photographic reproductions of full size engineering drawings, allowed the exact assembly of bonded or bolted parts by assembly mechanics, cutting costs and speeding production. While moisture absorption, high through-the-thickness coefficient of thermal expansion effects, and labor-intensive layup costs are potentially problematic in some cases, it is expected that solutions can be found through analytical and developmental programs.

Golden, C. T.↗
NASA NTRS1984

Frame Allines Fibers in Multilayer Composites

Jib ensures layers of fiber-reinforced preimpregnated tape correctly oriented in assembly of composite panels. Jig enables fast and reproductible alinement of fibers in multiaxis layups.

Clemons, J.↗
NASA NTRS1983

Hygrothermomechanical evaluation of transverse filament tape epoxy/polyester fiberglass composites

The static and cyclic load behavior of transverse filament tape (TFT) fiberglass/epoxy and TFY fiberglass/polyester composites, intended for use in the design of low-cost wind turbine blades, are presented. The data behavior is also evaluated with respect to predicted properties based on an integrated hygrothermomechanical response theory. Experimental TFT composite data were developed by the testing of laminates made by using composite layups typical of those used for the fabrication of TFT fiberglass wind turbine blades. Static properties include tension, compression, and interlaminar shear strengths at ambient conditions and at high humidity/elevated temperature conditions after a 500 hour exposure. Cyclic fatigue data were obtained using similar environmental conditions and a range of cyclic stresses. The environmental (temperature and moisture) and cyclic load effects on composite strength degradation are subsequently compared with the predictions obtained by using the composite life/durability theory. The results obtained show that the predicted hygrothermomechanical environmental effects on TFT composites are in good agreement with measured data for various properties including fatigue at different cyclic stresses.

Lark, R. L.↗
NASA NTRS1983

Performance of a quantitative study of instability-related delamination growth

An experimental program was conducted to quantify instability-induced imbedded delamination growth. Static tests on double cantilever beam (DCB) specimens yielded the critical mode 1 strain energy release rate (G sub 1 C) for T300/5208 graphite/epoxy. Static tests on mixed mode cracked lap shear (CLS) specimens, and a nonlinear finite element analysis (NFEA) of the CLS specimen to separate mode 1 and mode 2 effects, yielded the critical mode 2 strain energy release rate (G sub 2 C) for T300/5208. Constant amplitude fatigue tests on DCB and CLS specimens, along with the NFEA results on CLS specimens, quantified mode 1 and mode 2 contributions to delamination growth rate. Fatigue tests were conducted at a frequency (omega) of 10 Hertz, maintaining the minimum to maximum cyclic load ratio (R) at 0.05. Static compression and constant amplitude compression fatigue tests were also conducted on specimens with imbedded through the width (ITTW) delaminations. Kapton imbeddments were located below 3, 4 or 6 plies in a 64-ply laminate, during layup, to simulate ITTW delaminations.

Ramkumar, R. L.↗
NASA NTRS1983

A unifying strain criterion for fracture of fibrous composite laminates

Fibrous composite materials, such as graphite/epoxy, are light, stiff, and strong. They have great potential for reducing weight in aircraft structures. However, for a realization of this potential, designers will have to know the fracture toughness of composite laminates in order to design damage tolerant structures. In connection with the development of an economical testing procedure, there is a great need for a single fracture toughness parameter which can be used to predict the stress-intensity factor (K(Q)) for all laminates of interest to the designer. Poe and Sova (1980) have derived a general fracture toughness parameter (Qc), which is a material constant. It defines the critical level of strains in the principal load-carryng plies. The present investigation is concerned with the calculation of values for the ratio of Qc and the ultimate tensile strain of the fibers. The obtained data indicate that this ratio is reasonably constant for layups which fail largely by self-similar crack extension.

Poe, C. C., Jr.↗
NASA NTRS1982

Compression fatigue behavior of composites in the presence of delaminations

Three different stacking sequences of a 64-ply layup were tested in an experimental investigation of the effect of idealized imbedded delaminations on the compression fatigue behavior of quasi-isotropic T300/5208 graphite-epoxy laminates. Postfailure examination of specimen cross sections revealed the absence of any fiber microbuckling, suggesting that the predominant failure mode was the propagation of imbedded delaminations in the tab region. One- and two-dimensional delaminations, respectively located across the entire width below the surface ply and buried one or four plies below the surface, were considered. A novel procedure employing minute, laser-drilled holes was successfully used in extending the application of diidobutane-enhaced radiography to buried delaminations.

Ramkumar, R. L.↗
NASA NTRS1983

Analysis of progressive damage in thin circular laminates due to static-equivalent impact loads

Clamped circular graphite/epoxy plates (25.4, 38.1, and 50.8 mm radii) with an 8-ply quasi-isotropic layup were analyzed for static-equivalent impact loads using the minimum-total-potential-energy method and the von Karman strain-displacement equations. A step-by-step incremental transverse displacement procedure was used to calculate plate load and ply stresses. The ply failure region was calculated using the Tsai-Wu criterion. The corresponding failure modes (splitting and fiber failure) were determined using the maximum stress criteria. The first-failure mode was splitting and initiated first in the bottom ply. The splitting-failure thresholds were relatively low and tended to be lower for larger plates than for small plates. The splitting-damage region in each ply was elongated in its fiber direction; the bottom ply had the largest damage region. The calculated damage region for the 25.4-mm-radius plate agreed with limited static test results from the literature.

Shivakumar, K. N.↗
NASA NTRS1985

Silicone-Rubber Tooling for Hollow Panels

Wave-free contour surface obtained by using flexible mold. Silicone-rubber layup tool, when used in conjunction with hard plastic laminating mold defining desired contour, produces panel with wave-free surface that accurately reproduces shape of mold. In addition to providing porous hollow-panel wing structure that acts as duct for transporting sucked boundary layer tooling, also used to fabricate high-strength lightweight door panels and any single-or compound-contour panel.

Gallimore, F. H.↗