Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “layered structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Optical, structural and aging properties of Al/Sc-based multilayers for the extreme ultraviolet

This manuscript presents the structural characterization of Al/Sc-based periodic multilayer coatings for the extreme ultraviolet (EUV) spectral range. Based on transmission electron microscopy and electron diffraction as well as grazing-incidence and large-angle x-ray diffraction, a model for the layer structure and the interfacial effects of Al/Sc coatings is built. The onset of crystallization in nanoscale Al and Sc layers as a function of thickness is also revealed in these characterizations. The Al/Sc layer model is validated and further refined by fitting in-band and out-of-band EUV reflectance measurements across 5 orders of magnitude in an extended wavelength range from 17 to 80 nm. Here, the same type of EUV reflectance measurements is used to test the Al/Sc aging properties and to demonstrate the spectral response of optimized two- and tri-material multilayers including Al/Sc, Al/Sc/SiC and Mo/Al/Sc.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Roles of Mn and Co in Ni-rich layered oxide cathodes synthesized utilizing a Taylor Vortex Reactor

It is reported that layered oxides, composed of nickel, manganese, and cobalt (NMC), are sought after as cathode materials which provide improved energy density, cycle life, and safety in commercial lithium ion batteries (LIBs). Increasing Ni contents higher than 80% can provide even higher practical discharge capacities >200 mAh/g and similar to ~4 V discharge potential vs Li/Li + , making them promising cathodes for next generation LIBs. However, rapid capacity fade during cycling and heat-related safety concerns are delaying their successful transition to industry. We report systematic performance optimization of LiNiO 2 , LiNi 0.9 Mn 0.1 O 2 , and LiNi 0.9 Co 0.1 O 2 high Ni layered oxide cathodes synthesized by utilizing a Taylor Vortex Reactor. Co-free LiNi 0.9 Mn 0.1 O 2 cathode showed 200 mAh/g highest discharge capacity at 0.1 C rate with 84% retention after 103 cycles at 0.3C rate while LiNi 0.9 Co 0.1 O 2 cathode showed higher initial but poor cycle life (225 mAh/g highest discharge capacity at 0.1C rate with only 56% capacity retention after 103 cycles at 0.3 C rate. Synchrotron based X-ray diffraction (SXRD), X-ray absorption spectroscopy (XAS) and focused ion beam (FIB) imaging of pristine and cycled cathodes after 103 cycles provided important information on degradation mechanism. The roles of Mn and Co on layered structure formation, charge balance, cationic mixing, and electrochemical performance were elucidated using the crystallographic information from XRD refinement and electronic state analysis from XAS providing valuable information to design future Ni-rich layered oxide cathodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Anisotropic Thermal Transport in Quasi-2D Ruddlesden-Popper Hybrid Perovskite Superlattices

Two-dimensional hybrid metal-halide perovskites (2D-MHPs) have emerged as important solution-processed semiconductors with favorable optical and electronic properties for diverse applications in photovoltaics, optoelectronics, and spintronics. The quasi-2D layered structures, featuring large acoustic impedance mismatches between the organic and inorganic sublattices, are expected to result in distinct and anisotropic thermal transport properties along the cross-plane and in-plane directions. Here, we introduce transducer-free vibrational-pump-visible-probe (VPVP) approaches that enable accurate quantification of anisotropic thermal transport properties in various archetypical single-crystalline 2D-MHPs. Specifically, using VPVP spectroscopy and VPVP microscopy, we measure the anisotropic thermal diffusivities of 2D-MHPs with systematically varied Pb-I octahedral layer thicknesses, as well as organic spacer types and lengths, revealing how these structural parameters alter the cross-plane and in-plane thermal transport properties in distinct ways. While diffuse interface scattering plays an important role in dictating cross-plane thermal transport, in-plane thermal transport is primarily determined by phonon transport within interconnected inorganic layers. Density functional theory incorporating four-phonon scatterings provides further insight into the low thermal conductivity and modest thermal conduction anisotropy in 2D-MHPs. Our work demonstrates a new all-optical and noncontact method, which requires minimal sample preparation and allows direct visualization of cross-plane and in-plane thermal transport, potentially compatible with sample environments. The demonstrated VPVP approaches can advance understanding of thermal transport in 2D-MHPs as well as wide-ranging hybrid and polymeric semiconductors beyond 2D-MHPs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spontaneous Lithiation of Binary Oxides during Epitaxial Growth on LiCoO 2

Epitaxial growth is a powerful tool for synthesizing heterostructures and integrating multiple functionalities. Interfacial mixing can readily occur at temperatures required for complete film crystallization and can significantly modify the properties of layered structures, particularly for those containing energy storage materials with smaller cations. Here we show a two-step sequence involving the growth of an epitaxial LiCoO 2 cathode layer followed by the deposition of a binary transition metal oxide (WO 3 , TiO 2 , and others) in which controlled lithiation of the binary oxide occurs. Orientation-controlled epitaxial synthesis of the model solid-state-electrolyte Li 2 WO 4 and model anode material Li 4 Ti 5 O 12 occurs as WO 3 and TiO 2 nucleate their respective host lattices and attract Li ions from the underlying cathode. The cathode layer readily provides a tunable amount of Li ions for the controlled lithiation of the subsequent layer. We demonstrate that this approach can be used for energy materials discovery and exploring different combinations of epitaxial interfaces that can serve as well-defined model systems for mechanistic studies of energy storage and conversion processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Parasitic structure defect blights sustainability of cobalt-free single crystalline cathodes

Abstract Recent efforts to reduce battery costs and enhance sustainability have focused on eliminating Cobalt (Co) from cathode materials. While Co-free designs have shown notable success in polycrystalline cathodes, their impact on single crystalline (SC) cathodes remains less understood due to the significantly extended lithium diffusion pathways and the higher-temperature synthesis involved. Here, we reveal that removing Co from SC cathodes is structurally and electrochemically unfavorable, exhibiting unusual voltage fade behavior. Using multiscale diffraction and imaging techniques, we identify lithium-rich nanodomains (LRNDs) as a heterogeneous phase within the layered structure of Co-free SC cathodes. These LRNDs act as critical tipping points, inducing significant chemo-mechanical lattice strain and irreversible structural degradation, which exacerbates the voltage and capacity loss in electrochemical performance. Our findings highlight the considerable challenges of developing Co-free SC cathodes compared to polycrystalline ones and emphasize the need for new strategies to balance the interplay between cost, sustainability, and performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Regulating the Third Metal to Design and Engineer Multilayered NiFeM (M: Co, Mn, and Cu) Nanofoam Anode Catalysts for Anion-Exchange Membrane Water Electrolyzers

In this study, alkaline anion-exchange membrane water electrolyzers (AEMWEs) for green hydrogen production have received intensive attention due to their feasibility of using earth-abundant platinum group metal (PGM)-free catalysts. Herein, the third metal is incorporated into NiFe-based catalysts to regulate their electronic structures and morphologies, aiming to achieve sufficient oxygen evolution reaction (OER) activity and performance in AEMWEs. The ternary NiFeM (M: Cu, Co, or Mn) catalysts are featured with multiple layered structures and nanofoam network morphologies, consisting of highly OER-active amorphous Ni-rich oxide shells and electrically conductive metallic alloy cores. The physical and electronic perturbations to the NiFe induced by a third element lead to a fine-tuning of the redox ability of the metal sites at the reaction centers, which breaks the scaling relationship between OH* and O* intermediates at the reaction centers. Thus, the unique structural configuration and electronic regulation simultaneously benefit catalytic activity and performance improvements. These NiFeM nanofoam catalysts demonstrated promising anode performance in actual AEMWEs, comparable to the IrO 2 reference, especially at high current densities. Notably, using various electrolytes (e.g., KOH solution or pure water) for AEMWEs exhibited a different performance trend among studied NiFeM catalysts, likely due to dynamic changes of catalysts under various OER environments.

25 ENERGY STORAGE↗
DOE OSTI2023

Atmospheric Turbulent Intermittency Over the Arctic Sea‐Ice Surface During the MOSAiC Expedition

Turbulent motions in the Arctic stable boundary layer are characterized by intermittency, but they are rarely investigated due to limited observations, in particular over the sea‐ice surface. In the present study, we explore the characteristics of turbulent intermittency over the Arctic sea‐ice surface using data collected during the Multidisciplinary drifting Observation for the Study of Arctic Climate expedition from October 2019 to September 2020. We first develop a new algorithm, which performs well in identifying the spectral gap over the Arctic sea‐ice surface. Then the characteristics of intermittency are investigated. It is found that the strength of intermittency increases under the conditions of light surface wind speed, small surface wind speed gradient, and strong surface air temperature gradient. The momentum flux, sensible heat flux, and latent heat flux calculated by raw eddy‐covariance fluctuations are overestimated by 3%, 10%, and 24%, respectively, because submesoscale motions are included. Furthermore, the characteristics of the atmospheric boundary layer structure under various intermittency conditions reveal that strong low‐level jets are favorable to surface turbulent motions that result in weak intermittency, while strong temperature inversions above the surface layer suppress surface turbulent motions and lead to strong intermittency.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Nanostructured, Targeted Layered Metal Oxides as Active and Selective Heterogeneous Electrocatalysts for Oxygen Evolution

Oxygen evolution reaction (OER) is an important chemical transformation that governs the performance of technologically relevant energy conversion and storage processes, such as electrochemical water splitting in electrolyzers and metal-air batteries. This reaction involves the evolution of oxygen gas from (i) oxygen ions formed from water splitting at high temperatures, (ii) oxygen containing species (i.e., OH, OOH) formed from water splitting at low temperatures, and (iii) metal-oxide discharge products (M x O 2 ) in metal-air batteries. One of the main challenges with OER is that it is catalyzed at low temperatures by noble metal-based electrocatalysts, which are expensive (making this process economically unviable), or at high temperatures by metal-oxide based electrocatalysts that are inefficient and lead to high overpotential losses. Our preliminary results, as well as other results in the literature, show that non-noble metal-based oxide electrocatalysts with layered structures, known as nickelate oxides, exhibit promising OER activity. Nickelate oxides (A 2 MO 4+δ ) belong to the Ruddlesden-Popper series composed of alternating perovskite-like and rocksalt-like layers. They are promising OER electrocatalysts due to their high oxygen transport/exchange properties compared to the state-of-the-art perovskite-type oxides. Unfortunately, these materials are fairly unexplored and little is known about the properties that govern their OER activity. Our preliminary studies, where we combine density functional theory (DFT) calculations, selective synthesis and characterization, show that engineering their nanocrystalline structure can significantly impact their catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Tailoring the structure and electrochemical performance of sodium titanate anodes by post-synthesis heating

Sodium titanate anodes synthesized via “chimie-douce” methods generally require a post-synthesis dehydration step. Their crystal structures are sensitive to the heating conditions such as temperature, resulting in distinct sodium storage performance. Herein, using in situ and ex situ high-temperature X-ray diffraction, we studied in detail the structural changes of Na 0.74 Ti 1.815 $\square$ 0.185 O 4 ·1.27H 2 O (NTO) under various heating conditions. Electrochemical characterization revealed that NTOs heated at lower temperatures with layered structures deliver larger capacities than those heated at high temperatures with tunnel structures. Heat treatment at moderate temperatures greatly improves the capacity retention of NTO, especially stabilizing the high voltage processes that are major contributors to the capacity fading, because of the modified crystal structure and surface chemistry. As a result, our findings suggest that post-synthesis heating is a simple and effective strategy to tailor the crystal structure, surface chemistry, and electrochemical properties of sodium titanate anodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Enhancing carbon dioxide capture under humid conditions by optimizing the pore surface structure

Metal–organic frameworks (MOFs) exhibit significant potential for mitigating carbon emissions due to their high porosity and tunability. Despite numerous reports on CO 2 capture by MOF sorbents, a common challenge is their poor selectivity for CO 2 over water. Moreover, in-depth studies are much needed to elucidate the relationships among the pore surface structure, hydrophobicity, and CO 2 uptake capacity/selectivity. In this work, we investigate the factors influencing CO 2 adsorption capacity and selectivity under humidity in a series of isoreticular pillar-layer structures, Ni 2 (L) 2 (dabco) (L = bdc, ndc, adc). Our study shows that increasing ligand conjugation not only results in increased hydrophobicity, decreased pore size and BET surface area, but also leads to the change of primary binding sites of water molecules and higher binding energy of CO 2 , all of which contribute to largely increased CO 2 uptake capacity under humid conditions. Additionally, increasing ligand conjugation and consequently hydrophobicity slow down and reduce competitive water adsorption drastically. Notably, the MOF made of ligand with the highest conjugation, Ni 2 (adc) 2 (dabco), exhibits significantly enhanced CO 2 adsorption in N 2 /CO 2 binary mixtures under relatively high humidity (50% RH), with an increase of ~31% and ~36% for the composition of 15/85 and 50/50, respectively, compared to dry conditions. An experimental FTIR study and DFT theoretical calculations confirm that H 2 O occupies different primary binding site in Ni 2 (bdc) 2 (dabco) and Ni 2 (adc) 2 (dabco), and under humid conditions a higher binding energy of CO 2 is achieved with preferential H 2 O/CO 2 co-adsorption in Ni 2 (adc) 2 (dabco), potentially creating additional adsorption sites for CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

High pressure structural phase transitions in Dysprosium to 202 GPa

High pressure structural phase transitions in heavy lanthanide metal Dysprosium (Dy) have been studied to 202 GPa (Volume Compression V/V 0 = 0.36) in a diamond anvil cell employing copper as an internal x-ray pressure standard. The previously assigned monoclinic (C2/m) phase above 72 GPa has been reexamined and assigned to an orthorhombic phase with sixteen atoms per cell (oF16) based on structural refinements. The equation of state is presented to 202 GPa and indicates a volume change of 2.3% during the structural phase transition from distorted face-centered cubic (hR24) phase to oF16 phase at 72 GPa. The oF16 phase can be regarded as a pseudo-orthorhombic eight-layered structure with (b/c) ratio decreasing from an ideal value of $\sqrt{3}$ with increasing pressure to 202 GPa. The ultrahigh pressure structural phases of Dy are compared with other members of the lanthanide series.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dual Protective Mechanism of AlPO 4 Coating on High-Nickel Cathode Material for High Energy Density and Long Cycle Life Lithium-Ion Batteries

Cathode material with high nickel content is a promising candidate for the future generation of Li-ion batteries (LIBs). However, severe structural degradation during cycling limits its practical use, especially for electric vehicles. Herein, AlPO 4 nanoparticles were synthesized and then coated onto the surface of a high-nickel layer-structured cathode via a dry coating method. The AlPO 4 nanoparticles coating significantly improved the cycling stability from 69.2% to over 80% capacity retention after 140 cycles. Furthermore, the structure and chemical composition of the AlPO 4 -coated cathode was investigated by XRD, SEM, XPS, and STEM. Compared with the non-coated cathode, we revealed a dual protective mechanism for enhanced cycling stability, where Al doping and Li 3 PO 4 coating play synergistic roles in protecting cathode material through long-term cycling. This work demonstrates a facile and environmentally friendly approach toward improving the performance of high-nickel LIB cathodes, which can be easily scaled up for industrial applications.

25 ENERGY STORAGE↗
DOE OSTI2022

Synthesis, Crystal and Electronic Structures, Nonlinear Optical Properties, and Magnetic Properties of Two Thiophosphates: KInP 2 S 7 and KCrP 2 S 7

Two thiophosphates, KInP 2 S 7 and KCrP 2 S 7 , were structurally characterized without investigating any optical properties. Herein in this work, KInP 2 S 7 and KCrP 2 S 7 were revisited to investigate their optical and magnetic properties, respectively. Pure polycrystalline samples and crystals of KInP 2 S 7 and KCrP 2 S 7 were grown by high temperature solid state reactions, where mm-sized crystals of KCrP 2 S 7 were collected. KCrP 2 S 7 is isostructural to KInP 2 S 7 , which features a layered structure. KInP 2 S 7 and KCrP 2 S 7 possess close relationship to the layered thiophosphate M 2 P 2 S 6 (M = Fe, Co, Zn, etc.). The bonding pictures of KInP 2 S 7 were studied using the electron localization function (ELF) coupled with crystal orbital Hamilton population (COHP) calculations. The intrinsically distorted [PS 4 ] tetrahedra and [InS 6 ] octahedra are made by strong covalent P-S interactions and ionic In-S interactions, respectively. Electronic structure analysis confirmed that the optical properties of KInP 2 S 7 are mainly contributed to by [PS 4 ] tetrahedra together with small amounts of the contributions coming from [InS 6 ] octahedra. Magnetic measurement on mm-sized crystals of KCrP 2 S 7 verified that there is an antiferromagnetic transition around 21 K, and the Cr atoms are trivalent. KInP 2 S 7 is predicated to be an indirect bandgap semiconductor of 2.38 eV, which is confirmed by the UV-Vis measurement of 2.4(1) eV. KInP 2 S 7 is not a type-I phase-matching material and exhibits moderate second harmonic generation (SHG) response (0.51 × AgGaS 2 , sample of particle size of 100 µm). The laser damage threshold (LDT) of KInP 2 S 7 is very high of 5.2 × AgGaS 2 . Bandgap engineering were undergone to enhance the SHG response of KInP 2 S 7 .

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-Performance Low-Cobalt Cathode Materials for Li-ion Batteries

The layer-structured Li[Ni x Co y Mn 1-x-y ]O 2 (NCM) cathode materials have been the best choice for increasing electric vehicle driving distance per charge. The high Ni layered oxide represents successfully commercialized NCM cathodes (such as NCM622 and NCA) in lithium-ion batteries (LIBs) for EV applications due to their high energy density and acceptable cycling stability. However, the price of cobalt, the key element within LIBs for stability, has nearly tripled over the past few years due to increased demand from the cell phone industry. As mentioned in the DOE Funding Opportunity Announcement, the current materials shortage will also cause speculation for a future global shortage. Therefore, to meet the requirement and sustainability of the next-generation long-range and low-cost EVs, developing cathode materials with low-Co content to achieve higher energy density and lower cost is both essential and urgent. The overarching objective of this work is to develop stabilized NCM cathode materials with low Co content (namely LiNi x Co y Mn 1-x-y O 2 , y ≤ 0.04) to meet DOE’s goal of reducing Co loading below 50 mg Wh -1 while maintaining energy density greater than 600 Wh kg -1 based on cathode material. Via various dopings and coatings scalable methods, we explored and enhanced the cycling performance of low-cobalt cathodes. The final obtained NCM cathodes paired with graphite anode aim to deliver batteries with a high initial specific energy density of over 240 Wh kg -1 and a low capacity fading rate of less than 20% in 1000 cycles under a C/3 discharge rate. To accomplish this goal, a multidisciplinary team with several co-investigators has been formed from three organizations: The Pennsylvania State University (PSU), Oak Ridge National Laboratory (ORNL), and Pacific Northwest National Laboratory (PNNL). The PI and co-investigators are Dr. Donghai Wang (PI) from PSU with expertise in the synthesis of nanostructured materials and manipulation of interfacial properties of electrochemically active materials, Dr. Jagjit Nanda, with substantial knowledge of and expertise in state-of-the-art cathodes from ORNL, Dr. Chao-Yang Wang with significant experience in advanced cell design and fabrication and cell diagnostics from PSU, and Dr. Chongmin Wang with world-wide known expertise of advance atomic scale characterization of electrode materials from PNNL. Furthermore, this project will leverage and synergistically work with the current DOE-funded programs on battery materials at PSU and ORNL and electrode materials characterization at PNNL. During this funded period, we have accomplished milestones stated as follows: • Scale up production of LiFePO 4 (LFP) coated NCM811 with a production of 300g/batch. Fifteen (≥2 Ah) pouch cells with LFP-coated NCM811 cathode are delivered. Self-evaluated pouch cells in PSU show superior over 80% capacity retention performance even after 1500 cycles at C/3 rate. • Various cations (Al, Ti, Zr, and Mo) substitute cobalt in low-cobalt partially and Co-free cathodes. Their effects on crystal structure and electrochemical behavior are explored. • Phosphate compounds as coating materials represent promising surface protection precursors for low-cobalt cathode materials. Therefore, several metal phosphates were selected for improving the NMC cycling performance and are regarded as effective approaches for a scalable and practical surface protection method. • Production of NCM92, where Nickel content is 92% among transition metals, is scaled up from synthesis to coating and heat treatment procedures. Fifteen 2.7Ah pouch cells with Ti-doped NCM92 cathodes and industrial graphite anode are delivered to Idaho National Lab for testing.

25 ENERGY STORAGE↗
DOE OSTI2024

New examples of ferroelectric nematic materials showing evidence for the antiferroelectric smectic-Z phase

Abstract We present a new ferroelectric nematic material, 4-((4′-((trans)-5-ethyloxan-2-yl)-2′,3,5,6′-tetrafluoro-[1,1′-biphenyl]-4-yl)difluoromethoxy)-2,6-difluorobenzonitrile (AUUQU-2-N) and its higher homologues, the molecular structures of which include fluorinated building blocks, an oxane ring, and a terminal cyano group, all contributing to a large molecular dipole moment of about 12.5 D. We observed that AUUQU-2-N has three distinct liquid crystal phases, two of which were found to be polar phases with a spontaneous electric polarization P s of up to 6 µC cm –2 . The highest temperature phase is a common enantiotropic nematic (N) exhibiting only field-induced polarization. The lowest-temperature, monotropic phase proved to be a new example of the ferroelectric nematic phase (N F ), evidenced by a single-peak polarization reversal current response, a giant imaginary dielectric permittivity on the order of 10 3 , and the absence of any smectic layer X-ray diffraction peaks. The ordinary nematic phase N and the ferroelectric nematic phase N F are separated by an antiferroelectric liquid crystal phase which has low permittivity and a polarization reversal current exhibiting a characteristic double-peak response. In the polarizing light microscope, this antiferroelectric phase shows characteristic zig-zag defects, evidence of a layered structure. These observations suggest that this is another example of the recently discovered smectic Z A (SmZ A ) phase, having smectic layers with the molecular director parallel to the layer planes. The diffraction peaks from the smectic layering have not been observed to date but detailed 2D X-ray studies indicate the presence of additional short-range structures including smectic C-type correlations in all three phases—N, SmZ A and N F —which may shed new light on the understanding of polar and antipolar order in these phases.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deep Learning for Rapid Analysis of Spectroscopic Ellipsometry Data

High‐throughput experimental approaches to rapidly develop new materials require high‐throughput data analysis methods to match. Spectroscopic ellipsometry is a powerful method of optical properties characterization, but for unknown materials and/or layer structures the data analysis using traditional methods of nonlinear regression is too slow for autonomous, closed‐loop, high‐throughput experimentation. Herein, three methods (termed spectral, piecewise, and pointwise) of spectroscopic ellipsometry data analysis based on deep learning are introduced and studied. After initial training, the incremental time for inferring optical properties can be a thousand times faster than traditional methods. Results for multilayer sample structures with optically isotropic materials are presented, appropriate for high‐throughput studies of thin films of phase‐change materials such as GeSbTe (GST) alloys. Results for studies on highly birefringent layered materials are also presented, exemplified by the transition metal dichalcogenide MoS 2 . How the materials under test and the experimental objectives may guide the choice of analysis methods are discussed. The utility of our approach is demonstrated by analyzing data measured on a composition spread of GeSbTe phase‐change alloys containing 177 distinct compositions, and identifying the composition with optimal phase‐change figure of merit in only 1.4 s of analysis time.

Li, Yifei↗
DOE OSTI2023

Stacking disorder in α – RuCl 3 investigated via x-ray three-dimensional difference pair distribution function analysis

The van der Waals layered magnet α-RuCl 3 offers tantalizing prospects for the realization of Majorana quasiparticles. Efforts to understand this are, however, hampered by inconsistent magnetic and thermal transport properties likely coming from the formation of structural disorder during crystal growth, postgrowth processing, or upon cooling through the first order structural transition. Here, we investigate structural disorder in α-RuCl 3 using x-ray diffuse scattering and three-dimensional difference pair distribution function (3D-ΔPDF) analysis. We develop a quantitative model that describes disorder in α-RuCl 3 in terms of rotational twinning and intermixing of the high and low-temperature structural layer stacking. As a result, this disorder may be important to consider when investigating the detailed magnetic and electronic properties of this widely studied material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Surface reconstructions and electronic structure of metallic delafossite thin films

The growing interest in the growth and study of thin films of low-dimensional metallic delafossites, with the general formula ABO2, is driven by their potential to exhibit electronic and magnetic characteristics that are not accessible in bulk systems. The layered structure of these compounds introduces unique surface states as well as electronic and structural reconstructions, making the investigation of their surface behavior pivotal to understanding their intrinsic electronic structure. In this work, we study the surface phenomena of epitaxially grown PtCoO2, PdCoO2, and PdCrO2 films, utilizing a combination of molecular-beam epitaxy and angle-resolved photoemission spectroscopy. Through precise control of surface termination and treatment, we discover a pronounced 3×3 surface reconstruction in PtCoO2 films and PdCoO2 films, alongside a 2 × 2 surface reconstruction observed in PdCrO2 films. These reconstructions have not been reported in prior studies of delafossites. Furthermore, our computational investigations demonstrate the BO2 surface’s relative stability compared to the A-terminated surface and the significant reduction in surface energy facilitated by the reconstruction of the A-terminated surface. These experimental and theoretical insights illuminate the complex surface dynamics in metallic delafossites, paving the way for future explorations of their distinctive properties in low-dimensional studies.

Materials Science↗