Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lag effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Flight-determined lag of angle-of-attack and angle-of-sideslip sensors in the YF-12A airplane from analysis of dynamic maneuvers

Magnitudes of lags in the pneumatic angle-of-attack and angle-of-sideslip sensor systems of the YF-12A airplane were determined for a variety of flight conditions by analyzing stability and control data. The three analysis techniques used are described. An apparent trend with Mach number for measurements from both of the differential-pressure sensors showed that the lag ranged from approximately 0.15 second at subsonic speed to 0.4 second at Mach 3. Because Mach number was closely related to altitude for the available flight data, the individual effects of Mach number and altitude on the lag could not be separated clearly. However, the results indicated the influence of factors other than simple pneumatic lag.

Gilyard, G. B.↗
NASA NTRS1986

An experimental investigation of the flap-lag-torsion aeroelastic stability of a small-scale hingeless helicopter rotor in hover

A small scale, 1.92 m diam, torsionally soft, hingeless helicopter rotor was investigated in hover to determine isolated rotor stability characteristics. The two-bladed, untwisted rotor was tested on a rigid test stand at tip speeds up to 101 m/sec. The rotor mode of interest is the lightly damped lead-lag mode. The dimensionless lead-lag frequency of the mode is approximately 1.5 at the highest tip speed. The hub was designed to allow variation in precone, blade droop, pitch control stiffness, and blade pitch angle. Measurements of modal frequency and damping were obtained for several combinations of these hub parameters at several values of rotor speed. Steady blade bending moments were also measured. The lead-lag damping measurements were found to agree well with theoretical predictions for low values of blade pitch angle. The test data confirmed the predicted effects of precone, droop, and pitch control stiffness parameters on lead-lag damping. The correlation between theory and experiment was found to be poor for the mid-to-high range of pitch angles where the theory substantially overpredicted the experimental lead-lag damping. The poor correlation in the mid-to-high blade pitch angle range is attributed to low Reynolds number nonlinear aerodynamics effects not included in the theory. The experimental results also revealed an asymmetry in lead-lag damping between positive and negative thrust conditions.

Sharpe, David L.↗
NASA NTRS1983

Effects of viscosity on transonic-aerodynamic and aeroelastic characteristics of oscillating airfoils

Studies were made to investigate the effects of viscosity on aerodynamic and aeroelastic characteristics of oscillating airfoils. The computer code LTRAN2 (viscous), which is based on a small disturbance aerodynamic theory, was used to make aerodynamic computations. Two viscous models, the viscous-ramp model and the lag-entrainment model were considered. The unsteady viscous effects were obtained by use of the quasi-steady assumptions. Two cases, a conventional airfoil, NACA 64A010, and a supercritical airfoil, MBB-A3, were studied at Mach numbers 0.796 and 0.7557, respectively. For both the airfoils, steady and unsteady aerodynamic computations were made by using inviscid and viscous theories. The steady and the unsteady results for the NACA 64A010 airfoil and the steady results for the MBB-A3 airfoil were compared with the available wind-tunnel results. Flutter speeds were computed for both airfoils by using the U-g method and the effects of viscosity on the airfoils were studied. Results from the viscous methods show improvements over the inviscid method.

Guruswamy, P.↗
NASA NTRS1992

A new aeroelastic model for composite rotor blades with straight and swept tips

An analytical model for predicting the aeroelastic behavior of composite rotor blades with straight and swept tips is presented. The blade is modeled by beam type finite elements along the elastic axis. A single finite element is used to model the swept tip. The nonlinear equations of motion for the finite element model are derived using Hamilton's principle and based on a moderate deflection theory and accounts for: arbitrary cross-sectional shape, pretwist, generally anisotropic material behavior, transverse shears and out-of-plane warping. Numerical results illustrating the effects of tip sweep, anhedral and composite ply orientation on blade aeroelastic behavior are presented. Tip sweep can induce aeroelastic instability by flap-twist coupling. Tip anhedral causes lag-torsion and flap-axial couplings, however, its effects on blade stability is less pronounced than the effect due to sweep. Composite ply orientation has a substantial effect on blade stability.

Yuan, Kuo-An↗
NASA NTRS1973

Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations (the effects of some rotor feedback systems on rotor-body dynamics), Phase 7-A

The effects of three gyroless rotor feedback systems: (1) coning feedback, (2) proportional tilting feedback, and (3) a combination of these on the rotor-body dynamics of hingeless rotorcraft are studied with a simplified analytical model in the advance ratio range from 0 to .8. Combinations of feedback phase angles and control phase angles are selected to minimize control cross coupling and control sensitivity changes between low and high speed flight. For the feedback systems thus selected the effects of feedback gain and control actuator time lag on the stability both with fixed hub and in free flight is studied, whereby the rotorcraft is free in pitch, roll and vertical motion but otherwise restrained. For the free flight is studied, whereby the rotorcraft is free in pitch, roll and vertical motion but otherwise restrained. For the free flight conditions the effects of a horizontal tail are also determined in itself and in combination with the rotor feedback systems.

Hohenemser, K. H.↗
NASA NTRS1981

An assessment of buffer strips for improving damage tolerance

Graphite/epoxy panels with buffer strips were tested in tension to measure their residual strength with crack-like damage. Panels were made with 45/0/-45/90(2S) and 45/0/450(2S) layups. The buffer strips were parallel to the loading directions. They were made by replacing narrow strips of the 0 deg graphite plies with strips of either 0 deg S-Glass/epoxy or Kevlar-49/epoxy on either a one for one or a two for one basis. In a third case, O deg graphite/epoxy was used as the buffer material and thin, perforated Mylar strips were placed between the 0 deg piles and the cross-plies to weaken the interfaces and thus to isolate the 0 deg plies. Some panels were made with buffer strips of different widths and spacings. The buffer strips arrested the cracks and increased the residual strengths significantly over those plain laminates without buffer strips. A shear-lag type stress analysis correctly predicted the effects of layups, buffer material, buffer strip width and spacing, and the number of plies of buffer material.

Poe, C. C., Jr.↗
NASA NTRS1980

An assessment of buffer strips for improving damage tolerance of composite laminates

Graphite/epoxy panels with buffer strips were tested in tension to measure their residual strength with crack-like damage. Panels were made with (45/0/-45/90)2S and (45/0/-45/0)2S layups. The buffer strips were parallel to the loading direction. They were made by replacing narrow strips of the 0 deg graphite plies with strips of either 0 deg S-Glass/epoxy or Kevlar-90/epoxy on either a one-for-one or a two-for-one basis. In a third case, 0 deg graphite/epoxy was used as the buffer material and thin, perforated Mylar strips were placed between the 0 deg plies and the cross-plies to weaken the interfaces and thus to isolate the 0 deg plies. Some panels were made with buffer strips of different width and spacings. The buffer strips arrested the cracks and increased the residual strengths significantly over those of plain laminates without buffer strips. A shear-lag type stress analysis correctly predicted the effects of layup, buffer material, buffer strip width and spacing, and the number of plies of buffer material

Poe, C. C., Jr.↗
NASA NTRS1931

Penetration and Duration of Fuel Sprays from a Pump Injection System

High-speed motion pictures were taken of individual fuel sprays from a pump injection system. The changes in the spray-tip penetration with changes in the pump speed, injection-valve opening and closing pressures, discharge-orifice area, injection-tube length and diameter, and pump throttle setting were measured. In addition, the effects of the variables on the time lag and duration of injection can be controlled by the dimensions of the injection tube, the area of the discharge orifice, and the injection-valve opening and closing pressures.

Rothrock, A M↗
NASA NTRS1935

Combustion in a Bomb with a Fuel-Injection System

Fuel injected into a spherical bomb filled with air at a desired density and temperature could be ignited with a spark a few thousandths of a second after injection, an interval comparable with the ignition lag in fuel-injection engines. The effect of several variables on the extent and rate of combustion was investigated: time intervals between injection and ignition of fuel of 0.003 to 0.06 second and one of 5 minutes; initial air temperatures of 100 degrees C. to 250 degrees C.; initial air densities equivalent to 5, 10, and 15 absolute atmospheres pressure at 100 degrees C.; and air-fuel ratios of 5 to 25.

Cohn, Mildred↗
NASA NTRS2002

Supergranule Rotation Rates and Lifetimes

Previous measurements of the rotation rate of the supergranule Doppler pattern have revealed three interesting characteristics. 1) The supergranule pattern rotates faster than the plasma at the surface and, at each latitude, it rotates faster than the plasma at any level below the surface. 2) Larger cells rotate more rapidly than smaller cells. 3) Faster rotation rates are found when using larger time lags between Doppler images. These last two characteristics are consistent with the idea that large cells live longer and extend deeper into the Sun where the rotation rate is faster. A re-examination of the rotation rates and lifetimes of the Doppler patterns seen with the Michelson Doppler Imager (MDI) instrument on Solar and Heliospheric Observatory (SOHO) confirms these characteristics. However, a simulation of the data using a spectrum for the cellular flows that matches the observed spectrum shows that these characteristics can be largely reproduced by cellular patterns that rotate at the same rate without any dependence upon cell size, The rotation rate , and its dependence on latitude, is nonetheless still faster than the surface or internal rotation rate. The difference in rotation rates as functions of cell size and time lag between observations is attributed to projection effects on the line-of-sight Doppler signal. This data simulation is also used to determine characteristic lifetimes for the cellular patterns as a function of cell size. These lifetime determinations are also affected by projection effects on the line-of-sight Doppler signal.

Hathaway, David H.↗
NASA NTRS2002

Implications of Lag-Luminosity Relationship for Unified GRB Paradigms

Spectral lags (tau(sub lag)) are deduced for 1437 long (T(sub 90) greater than 2 s) BATSE gamma-ray bursts (GRBs) with peak flux F(sub p) greater than 0.25 photons cm(sup -2)/s, near to the BATSE trigger threshold. The lags are modeled to approximate the observed distribution in the F(sub p)-T(sub lag) plane, realizing a noise-free representation. Assuming a two-branch lag-luminosity relationship, the lags are self-consistently corrected for cosmological effects to yield distributions in luminosity, distance, and redshift. The results have several consequences for GRB populations and for unified gamma-ray/afterglow scenarios which would account for afterglow break times and gamma-ray spectral evolution in terms of jet opening angle, viewing angle, or a profiled jet with variable Lorentz factor: A component of the burst sample is identified - those with few, wide pulses, lags of a few tenths to several seconds, and soft spectra - whose Log[N]-Log[F(sub p)] distribution approximates a -3/2 power-law, suggesting homogeneity and thus relatively nearby sources. The proportion of these long-lag bursts increases from negligible among bright BATSE bursts to approx. 50% at trigger threshold. Bursts with very long lags, approx. 1-2 less than tau(sub lag) (S) less than 10, show a tendency to concentrate near the Supergalactic Plane with a quadrupole moment of approx. -0.10 +/- 0.04. GRB 980425 (SN 1998bw) is a member of this subsample of approx. 90 bursts with estimated distances less than 100 Mpc. The frequency of the observed ultra-low luminosity bursts is approx. 1/4 that of SNe Ib/c within the same volume. If truly nearby, the core-collapse events associated with these GRBs might produce gravitational radiation detectable by LIGO-II. Such nearby bursts might also help explain flattening of the cosmic ray spectrum at ultra-high energies, as observed by AGASA.

Norris, J. P.↗
NASA NTRS1992

Research on measurement and control of helicopter rotor response using blade-mounted accelerometers 1991-92

Preliminary wind tunnel tests of the hill-size Model 412/IBC rotor at the Ames Research Center, NASA, are described. Blade flapping motion was excited by swash plate oscillation, and the flapping response was measured using blade-mounted accelerometers and compared with flapping motion inferred form blade strain measurements. The recorded open-loop accelerometer signals were used as input to the flapping-IBC system in the laboratory. The resulting controller cyclic pitch outputs are compared with the original cyclic pitch excitation inputs, and the potential effectiveness of the controller in suppressing the original excitation is evaluated. Control of blade flapping excites blade lagging, and vice versa; the paper describes a theoretical investigation of these coupling effects.

Ham, Norman D.↗
NASA NTRS2024

Analytical Simulation of Effects of Local Mechanisms and Microstructure on Creep Response of Unidirectional Ceramic Matrix Composites

A micromechanics-based method has been developed to analyze the creep response of uncoated ceramic matrix minicomposites. Although the global stress level at which the creep response is analyzed is lower than the composite proportional limit, local stresses are assumed to be high enough that localized damage is present in the composite in the form of matrix microcracks. To model the composite creep response, including the effects of matrix cracking, a fiber shear lag-based methodology is employed. In this approach, stresses are assumed to vary in the fiber as a function of time and distance from the crack plane. The varying stresses are then used to compute the overall creep strain for the composite. Various assumptions regarding the level of matrix microcracking in the composite and the level of creep in the fiber and matrix in various portions of the composite unit cell are also examined. The creep response of the fiber is modeled using a linear Burgers model. The model is applied to a SiCf/SiC unidirectional minicomposite system. The computed creep results are compared to experimentally obtained values. The effects of the local fiber volume fraction on the overall creep response of the composite are also studied. This work will allow increased understanding of the key material damage mechanisms and load sharing that take place during creep conditions and can be expanded to provide improved analysis methods for full macrocomposites.

Micromechanics↗
NASA NTRS2024

Analytical Simulation of the Effects of Local Mechanisms and Microstructure on the Creep Response of Unidirectional Ceramic Matrix Composites

A micromechanics-based method has been developed to analyze the creep response of uncoated ceramic matrix minicomposites. Although the global stress level at which the creep response is analyzed is lower than the composite proportional limit, local stresses are assumed to be high enough that localized damage is present in the composite in the form of matrix microcracks. To model the composite creep response including the effects of matrix cracking, a fiber shear lag-based methodology is employed. In this approach, stresses are assumed to vary in the fiber as a function of time and distance from the crack plane. The varying stresses are then used to compute the overall creep strain for the composite. Various assumptions regarding the level of matrix microcracking in the composite, and the level of creep in the fiber and matrix in various portions of the composite unit cell, are also examined. The creep response of the fiber is modeled using a linear Burgers model. The model is applied to a SiC f /SiC unidirectional minicomposite system. The computed creep results are compared to experimentally obtained values. The effects of the local fiber volume fraction on the overall creep response of the composite are also studied. This work will allow increased understanding of the key material damage mechanisms and load sharing that take place during creep conditions and can be expanded to provide improved analysis methods for full macrocomposites.

Micromechanics↗
NASA NTRSDate not supplied

Process Recipes for Additively Printed Copper Ink Flexible Circuits using Direct Write Methods

In this paper, the process-recipes and process-performance relationships for additive-printing of copper circuits using direct-write methods have been studied. The process has been implemented on the direct write platform. Interest in the use of additive printing methods for the manufacture of micro-circuits has grown immensely in recent times. Direct write methods have been shown to have the ability to create circuits in a limited manner. However, the process recipes and the effect of process parameters on the manufactured properties are not well understood. Copper ink is a good and cost-effective alternative to silver ink but its use has lagged owing to an increased propensity for oxidation. In this paper, photonic curing has been used to sinter copper ink to make the traces conductive. The method flashes high energy light that sinter metal particles instantaneously and the temperature of the substrate remains low. The effect of the different photonic sintering profiles on the mechanical and electrical properties of the printed traces has been studied in this paper.The print process parameters also play an important role in the line width and height that has been studied to print with the desired line profile for the end application. An LC filter circuit is been printed with SMD components been attached using an electrically conductive adhesive (ECA). The manufactured flexible LC filter is been tested for its frequency sweep to compare with the commercially available LC filer with the help of the Bode plot.

Process control↗
NASA NTRS1978

Effects of errors on decoupled control systems

Various error sources in a decoupled control system are considered in connection with longitudinal control on a simulated externally blown jet-flap STOL aircraft. The system employed the throttle, horizontal tail, and flaps to decouple the forward velocity, pitch angle, and flight-path angle. The errors considered were: (1) imperfect knowledge of airplane aerodynamic and control characteristics; (2) imperfect measurements of airplane state variables; (3) change in flight conditions, and (4) lag in the airplane controls and in engine response. The effects of the various errors on the decoupling process were generally minor. Significant coupling in flight-path angle was caused by control lag during speed-command maneuvers. However, this coupling could be eliminated by including the control lag in the design of the decoupled system. Other error sources affected primarily the commanded response quantity.

Hamer, H. A.↗
DOE OSTI2025

Climate change and federal aid disbursements after Hurricane Harvey: an extreme event attribution analysis

The role climate change plays in increasing the burden placed on governments and insurers to pay for recovery has not been extensively explored and is the focus of this study. This study examines the impacts of climate change attributed flooding on federal disaster aid disbursement in Harris County, Texas following Hurricane Harvey in 2017. Our approach uses flood models to estimate the amount of flood damages attributable and not attributable to climate change under two climate change attribution scenarios from peer reviewed studies: 20% and 38% increases in rainfall associated with the hurricane due to climate change. These estimates are combined with census tract-level disbursement data for FEMA’s National Flood Insurance Program (NFIP) and the Individual Assistance (IA) part of the Individuals and Households Program. We employ spatial lag regression models with direct and spatial spillover effects to analyze the relationship between a tract’s flood damages—both attributed and not attributed to climate change—and federal disaster aid. We find that both types of flood damage shape federal aid disbursements, but that climate change attributed damages tend to have larger effect sizes (elasticities) especially for IA. Specifically, for a 1% increase in additional climate change attributed damages per household in a census tract (under the 20% scenario), expected NFIP levels in that census tract are 0.26% higher and IA levels are 0.3% higher. Implications center on federal funding in an era of climate change.

FEMA↗
NASA NTRS1974

Computer simulation of a fringe type laser velocimeter

A computer simulation of a fringe type laser velocimeter has been written to determine the theoretical characteristics of the laser velocimeter when applied to a given flow field. The program includes the effect of particle size and composition on particle lag, light scattering characteristics and signal contrast. The model of the laser velocimeter includes the laser, optical system, photomultiplier, and counter type data processing electronics. The LV particle size analyzer is also modeled and incorporated in the program. An example application of the program to a Mach 5 wind tunnel using a backscatter laser velocimeter is presented.

Meyers, J. F.↗