SEARCH · Engineering Papers

Results for “integrated arrival”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Evaluation of Flight Deck-Based Interval Management Crew Procedure Feasibility

Air traffic demand is predicted to increase over the next 20 years, creating a need for new technologies and procedures to support this growth in a safe and efficient manner. The National Aeronautics and Space Administration's (NASA) Air Traffic Management Technology Demonstration - 1 (ATD-1) will operationally demonstrate the feasibility of efficient arrival operations combining ground-based and airborne NASA technologies. The integration of these technologies will increase throughput, reduce delay, conserve fuel, and minimize environmental impacts. The ground-based tools include Traffic Management Advisor with Terminal Metering for precise time-based scheduling and Controller Managed Spacing decision support tools for better managing aircraft delay with speed control. The core airborne technology in ATD-1 is Flight deck-based Interval Management (FIM). FIM tools provide pilots with speed commands calculated using information from Automatic Dependent Surveillance - Broadcast. The precise merging and spacing enabled by FIM avionics and flight crew procedures will reduce excess spacing buffers and result in higher terminal throughput. This paper describes a human-in-the-loop experiment designed to assess the acceptability and feasibility of the ATD-1 procedures used in a voice communications environment. This experiment utilized the ATD-1 integrated system of ground-based and airborne technologies. Pilot participants flew a high-fidelity fixed base simulator equipped with an airborne spacing algorithm and a FIM crew interface. Experiment scenarios involved multiple air traffic flows into the Dallas-Fort Worth Terminal Radar Control airspace. Results indicate that the proposed procedures were feasible for use by flight crews in a voice communications environment. The delivery accuracy at the achieve-by point was within +/- five seconds and the delivery precision was less than five seconds. Furthermore, FIM speed commands occurred at a rate of less than one per minute, and pilots found the frequency of the speed commands to be acceptable at all times throughout the experiment scenarios.

Wilson, Sara R.↗

NASA NTRS1987

EASE/ACCESS ground processing at Kennedy Space Center

The Kennedy Space Center (KSC) Payload Management and Operations Directorate is responsible for the processing of Space Shuttle payloads. The KSC responsibilities begin prior to hardware arrival at the launch site and extend until the experiments are returned to the investigators after the flight. The KSC involvement with the integration and checkout of payloads begins with participation in experiment, Mission Peculiar Equipment (MPE), and integrated payload design reviews. This involvement also includes participation in assembly and testing of flight hardware at the appropriate design center, university, or private corporation. Once the hardware arrives at the launch site, KSC personnel install the experiments and MPE onto a carrier in the Operations and Checkout (O & C) building. Following integration, the payload is functionally tested and then installed into the orbiter. After the mission, the payload is removed from the orbiter, deintegrated in the O & C building, and the experiments are turned over to the mission manager. One of the many payloads process at KSC consisted of two space construction experiments: the Experimental Assembly of Structures in Extravehicular Activity (EASE) and the Assembly Concept for Construction of Erectable Space Structures (ACCESS). The details of EASE/ACCESS integration, testing, and deintegration are addressed and how this mission can serve as a guide for future space construction payloads is discussed.

Moates, Deborah J.↗

NASA NTRS1998

Preliminary Assessment of a Neptune Aerocapture Mission Using an Integrated Design Tool

Aerocapture is an efficient orbit insertion technique that uses the planet's atmosphere to decelerate an arriving spacecraft. With current technology and for vehicles of reasonable mass, it is the only technique that might deliver the high delta-V's required for insertion to orbits around the outer planets. Preliminary design studies for outer planet orbital missions must evaluate aerocapture strategies, and must therefore consider the coupling between vehicle geometry, aerodynamics, aerocapture trajectory, heating and thermal protection system mass. The analyses have been linked into an integrated design environment, with the critical parameters grouped in a global database. The designer is free to use single point evaluations, parametric variation, and numerical optimization to evaluate a range of vehicle shapes and insertion trajectories. The application of this design tool to a preliminary study for Neptune aerocapture has implications for the use of such computational environments for any atmospheric entry mission.

Gage, Peter J.↗

NASA NTRS1974

Life sciences payload definition and integration study. Volume 2: Requirements, design, and planning studies for the carry-on laboratories

The task phase concerned with the requirements, design, and planning studies for the carry-on laboratory (COL) began with a definition of biomedical research areas and candidate research equipment, and then went on to develop conceptual layouts for COL which were each evaluated in order to arrive at a final conceptual design. Each step in this design/evaluation process concerned itself with man/systems integration research and hardware, and life support and protective systems research and equipment selection. COL integration studies were also conducted and include attention to electrical power and data management requirements, operational considerations, and shuttle/Spacelab interface specifications. A COL program schedule was compiled, and a cost analysis was finalized which takes into account work breakdown, annual funding, and cost reduction guidelines.

Source record↗

NASA NTRS2007

Lunar Orbit Insertion Targeting and Associated Outbound Mission Design for Lunar Sortie Missions

This report details the Lunar Orbit Insertion (LOI) arrival targeting and associated mission design philosophy for Lunar sortie missions with up to a 7-day surface stay and with global Lunar landing site access. It also documents the assumptions, methodology, and requirements validated by TDS-04-013, Integrated Transit Nominal and Abort Characterization and Sensitivity Study. This report examines the generation of the Lunar arrival parking orbit inclination and Longitude of the Ascending Node (LAN) targets supporting surface missions with global Lunar landing site access. These targets support the Constellation Program requirement for anytime abort (early return) by providing for a minimized worst-case wedge angle [and an associated minimum plane change delta-velocity (V) cost] between the Crew Exploration Vehicle (CEV) and the Lunar Surface Access Module (LSAM) for an LSAM launch anytime during the Lunar surface stay.

Condon, Gerald L.↗

NASA NTRS1969

The use of satellite beacons for meteorological research

The use of microwave beacon transmissions from synchronous and near synchronous satellites is discussed as a means of measuring atmospheric absorption. It is suggested that, with a fixed angle of elevation of a synchronous satellite, complete diurnal coverage of the integrated absorption is available. In addition, with refined interferometric equipment, angle of arrival studies can be made and phase deviations measured.

Aarons, J.↗

NASA NTRS1988

Survey of optimization techniques for nonlinear spacecraft trajectory searches

Mathematical analysis of the optimal search of a nonlinear spacecraft trajectory to arrive at a set of desired targets is presented. A high precision integrated trajectory program and several optimization software libraries are used to search for a converged nonlinear spacecraft trajectory. Several examples for the Galileo Jupiter Orbiter and the Ocean Topography Experiment (TOPEX) are presented that illustrate a variety of the optimization methods used in nonlinear spacecraft trajectory searches.

Wang, Tseng-Chan↗

NASA NTRS2000

Next Generation CTAS Tools

The FAA's Free Flight Phase 1 Office is in the process of deploying the current generation of CTAS tools, which are the Traffic Management Advisor (TMA) and the passive Final Approach Spacing Tool (pFAST), at selected centers and airports. Research at NASA is now focussed on extending the CTAS software and computer human interfaces to provide more advanced capabilities. The Multi-center TMA (McTMA) is designed to operate at airports where arrival flows originate from two or more centers whose boundaries are in close proximity to the TRACON boundary. McTMA will also include techniques for routing arrival flows away from congested airspace and around airspace reserved for arrivals into other hub airports. NASA is working with FAA and MITRE to build a prototype McTMA for the Philadelphia airport. The active Final Approach Spacing Tool (aFAST) provides speed and heading advisories to help controllers achieve accurate spacing between aircraft on final approach. These advisories will be integrated with those in the existing pFAST to provide a set of comprehensive advisories for controlling arrival traffic from the TRACON boundary to touchdown at complex, high-capacity airports. A research prototype of aFAST, designed for the Dallas-Fort Worth is in an advanced stage of development. The Expedite Departure Path (EDP) and Direct-To tools are designed to help controllers guide departing aircraft out of the TRACON airspace and to climb to cruise altitude along the most efficient routes.

Erzberger, Heinz↗

NASA NTRS2013

Evaluation of the Controller-Managed Spacing Tools, Flight-Deck Interval Management and Terminal Area Metering Capabilities for the ATM Technology Demonstration #1

NASA has developed a suite of advanced arrival management technologies combining time-based scheduling with controller- and flight deck-based precision spacing capabilities that allow fuel-efficient arrival operations during periods of high throughput. An operational demonstration of these integrated technologies, i.e., the ATM Technology Demonstration #1 (ATD-1), is slated for 2016. Human-in-the-loop simulations were conducted to evaluate the performance of the ATD-1 system and validate operational feasibility. The ATD-1 system was found to be robust to scenarios with saturated demand levels and high levels of system delay. High throughput, 10 above baseline demand levels, and schedule conformance less than 20 seconds at the 75th percentile were achievable. The flight-deck interval management capabilities also improved the median schedule conformance at the final approach fix from 5 to 3 seconds with less variance.

terminal metering↗

NASA NTRSDate not supplied

A Method for Validating Causal Diagrams of Human Health Risk in Space Flight

The complexity of cause-and-effect relationships between spaceflight hazards and resulting health conditions clouds understanding of the totality of human system risk in space. In response, NASA has introduced Directed Acyclic Graphs (causal diagrams) into the human systems risk management process. These diagrams allow for a common understanding of the mechanisms that lead from unique hazards of spaceflight to the health outcomes important to agencies and astronauts. However, the paucity of available biomedical data from spaceflight creates a need for methods of validating causal models that can accommodate data from spaceflight model analogs. Here we outline one approach utilizing open-access rodent bone datasets from the Ames Life Sciences Data Archive. The properties of directed acyclic graphs themselves can provide an epistemological and statistical framework for validation of a priori causal representations of human system risk in space flight. The assumed causal connections on the graph creates sets of logical implications: variables that – if the causal diagram is correct – should be correlated, as well as sets that should be conditionally independent. By testing these implied correlations and conditional independencies both statistically and heuristically, we can provide evidence for or against specific causal pathways on the causal diagram. In addition to validation of expert-generated causal diagrams, machine learning techniques can learn the most likely structure of a causal diagram from a given dataset. Comparison with and reconciliation between machine-learned causal diagrams and expert-generated diagrams is another technique for challenging assumptions and improving our understanding of causal mechanisms. Accurately representing complex causation is essential to systemic understanding of human health risks in space travel. Having a robust system of validating causal diagrams helps us arrive at more accurate representations of causal systems. This process will be integral to developing the countermeasures necessary for extended exploration of the moon and Mars.

Robert Reynolds↗

NASA NTRS2026

Prototype Demonstration of Solar-Carbothermal System to Extract Oxygen From Regolith

The Carbothermal Reduction Demonstration (CaRD) project was an effort to develop a prototype system to demonstrate the extraction of oxygen from simulated lunar regolith using concentrated solar energy and a carbothermal reaction. The prototype consisted of a deployable solar concentrator capable of tracking the sun, carbothermal reactor, fluid system, gas analysis, and a solar concentrator control system consisting of avionics and software. These subsystems were developed by multiple NASA centers and a private industry partner, Sierra Space. The various teams worked together to define requirements and interfaces to successfully assemble the complex system and demonstrate an integrated solar carbothermal process. The solar concentrator developed at Glenn Research Center (GRC) was designed to be stowed for a launch environment then deployed on the lunar surface. It utilized a crossed dragone configuration of composite mirrors to direct horizontal sunlight onto a target 90° from the incoming sunlight. The key performance parameters for the solar concentrator were efficiency and power density. The carbothermal reactor was developed by Sierra Space through a separate project called the Carbothermal Oxygen Production Reactor (COPR) where it successfully demonstrated a fully automated process in a thermal vacuum environment [1]. The fluid system needed for the carbothermal reaction was also developed by Sierra Space and successfully demonstrated in the same thermal vacuum test. The gas analysis system was developed at Kennedy Space Center (KSC) and was required to determine the amount of oxygen extracted during each test. The gas analysis system was based on the Mass Spectrometer Observing Lunar Operations (MSOLO) instrument. Avionics and software for the CaRD prototype were also developed at KSC and based on experience with MSOLO avionics and software. The control system was designed to stow, deploy, track the sun, and perform beam alignment of the concentrated light. The prototype subsystems were integrated and tested at Johnson Space Center’s (JSC) Energy Systems Test Area. A heliostat was used to direct sunlight toward the prototype in a way that is representative of the sunlight conditions at the south pole of the Moon. When concentrated sunlight was focused on simulated lunar regolith within the reactor, the gas analysis team confirmed the presence of carbon monoxide gas, which confirmed that a solar carbothermal reaction took place. The key performance parameter for the integrated prototype was grams of oxygen extracted per kilowatt hour of energy arriving at the concentrator primary mirror. The prototype design successfully demonstrated end-to-end capability and further steps to achieve a flight capable system have been defined. With lunar data, engineers would be able to design a scaled-up system capable of extracting oxygen from regolith at useful quantities for crew life support and rocket propellant. On the long term, this method of In-Situ Resource Utilization could be used to drastically reduce the cost and risk of a sustained human presence on the Moon by reducing the amount of oxygen that would have to be delivered.

Koorosh R Araghi↗

NASA NTRS2026

Prototype Demonstration of Solar Carbothermal System to Extract Oxygen from Regolith

The Carbothermal Reduction Demonstration (CaRD) project was an effort to develop a prototype system to demonstrate the extraction of oxygen from simulated lunar regolith using concentrated solar energy and a carbothermal reaction. The prototype consisted of a deployable solar concentrator capable of tracking the sun, carbothermal reactor, fluid system, gas analysis, and a solar concentrator control system consisting of avionics and software. These subsystems were developed by multiple NASA centers and a private industry partner, Sierra Space. The various teams worked together to define requirements and interfaces to successfully assemble the complex system and demonstrate an integrated solar carbothermal process. The solar concentrator developed at Glenn Research Center (GRC) was designed to be stowed for a launch environment then deployed on the lunar surface. It utilized a crossed dragone configuration of composite mirrors to direct horizontal sunlight onto a target 90° from the incoming sunlight. The key performance parameters for the solar concentrator were efficiency and power density. The carbothermal reactor was developed by Sierra Space through a separate project called the Carbothermal Oxygen Production Reactor (COPR) where it successfully demonstrated a fully automated process in a thermal vacuum environment. The fluid system needed for the carbothermal reaction was also developed by Sierra Space and successfully demonstrated in the same thermal vacuum test. The gas analysis system was developed at Kennedy Space Center (KSC) and was required to determine the amount of oxygen extracted during each test. The gas analysis system was based on the Mass Spectrometer Observing Lunar Operations (MSOLO) instrument. Avionics and software for the CaRD prototype were also developed at KSC and based on experience with MSOLO avionics and software. The control system was designed to stow, deploy, track the sun, and perform beam alignment of the concentrated light. The prototype subsystems were integrated and tested at Johnson Space Center’s (JSC) Energy Systems Test Area. A heliostat was used to direct sunlight toward the prototype in a way that is representative of the sunlight conditions at the south pole of the Moon. When concentrated sunlight was focused on simulated lunar regolith within the reactor, the gas analysis team confirmed the presence of carbon monoxide gas, which confirmed that a solar carbothermal reaction took place. The key performance parameter for the integrated prototype was grams of oxygen extracted per kilowatt hour of energy arriving at the concentrator primary mirror. The prototype design successfully demonstrated end-to-end capability and further steps to achieve a flight capable system have been defined. With lunar data, engineers would be able to design a scaled-up system capable of extracting oxygen from regolith at useful quantities for crew life support and rocket propellant. On the long term, this method of In-Situ Resource Utilization could be used to drastically reduce the cost and risk of a sustained human presence on the Moon by reducing the amount of oxygen that would have to be delivered.

Aaron Paz↗

NASA NTRS2026

Prototype Demonstration of an Integrated Solar Concentrator System and Carbothermal Reactor Using Solar Energy to Extract Oxygen from Regolith

The Carbothermal Reduction Demonstration (CaRD) project was an effort to develop a prototype system to demonstrate the extraction of oxygen from simulated lunar regolith using concentrated solar energy and a carbothermal reaction. The prototype consisted of a deployable solar concentrator capable of tracking the sun, carbothermal reactor, fluid system, gas analysis, and a solar concentrator control system consisting of avionics and software. These subsystems were developed by multiple NASA centers and a private industry partner, Sierra Space. The various teams worked together to define requirements and interfaces to successfully assemble the complex system and demonstrate an integrated solar carbothermal process. The solar concentrator developed at Glenn Research Center (GRC) was designed to be stowed for a launch environment then deployed on the lunar surface. It utilized a crossed dragone configuration of composite mirrors to direct horizontal sunlight onto a target 90° from the incoming sunlight. The key performance parameters for the solar concentrator were efficiency and power density. The carbothermal reactor was developed by Sierra Space through a separate project called the Carbothermal Oxygen Production Reactor (COPR) where it successfully demonstrated a fully automated process in a thermal vacuum environment. The fluid system needed for the carbothermal reaction was also developed by Sierra Space and successfully demonstrated in the same thermal vacuum test. The gas analysis system was developed at Kennedy Space Center (KSC) and was required to determine the amount of oxygen extracted during each test. The gas analysis system was based on the Mass Spectrometer Observing Lunar Operations (MSOLO) instrument. Avionics and software for the CaRD prototype were also developed at KSC and based on experience with MSOLO avionics and software. The control system was designed to stow, deploy, track the sun, and perform beam alignment of the concentrated light. The prototype subsystems were integrated and tested at Johnson Space Center’s (JSC) Energy Systems Test Area. A heliostat was used to direct sunlight toward the prototype in a way that is representative of the sunlight conditions at the south pole of the Moon. When concentrated sunlight was focused on simulated lunar regolith within the reactor, the gas analysis team confirmed the presence of carbon monoxide gas, which confirmed that a solar carbothermal reaction took place. The key performance parameter for the integrated prototype was grams of oxygen extracted per kilowatt hour of energy arriving at the concentrator primary mirror. The prototype design successfully demonstrated end-to-end capability and further steps to achieve a flight capable system have been defined. With lunar data, engineers would be able to design a scaled-up system capable of extracting oxygen from regolith at useful quantities for crew life support and rocket propellant. On the long term, this method of In-Situ Resource Utilization could be used to drastically reduce the cost and risk of a sustained human presence on the Moon by reducing the amount of oxygen that would have to be delivered.

Oxygen from Regolith↗

NASA NTRS1991

Diverter - Perspectives on the integration and display of flight critical information using an expert system and menu-driven displays

An expert system prototype, called Diverter, was developed which evaluates, integrates, and displays flight plan recommendations to the pilot during the planning of an inflight diversion. The system integrates information from many sources to provide a comprehensive description of the flight planning alternatives available to the pilot. Diverter evaluates all applicable constraints to arrive at a flight plan to make efficient use of manpower, fuel, and time. The use of an expert system automates much of the integration and evaluation of variables impacting the flight. The use of hierarchical menu-driven displays and direct manipulation interface techniques may reduce workload.

Rudolph, Frederick M.↗

NASA NTRS1999

Design of a Novel Gaseous Hydrogen-Oxygen Rocket Injector Element

NASA and Aerojet are developing a Rocket-Based Combined Cycle (RBCC) engine under the Advanced Reusable Technology program. The rocket application requires that the combustion process be stable, complete, and take place in as short a distance as possible without compromising the structural integrity of the injector itself. A novel gaseous hydrogen-oxygen rocket injector element design was arrived at through an iterative design process making extensive use of CFD simulations, which resulted in a design that is meeting design goals. Sub-scale versions of the injector have been built and tested in a unique test-rig and in a sub-scale RBCC engine. The Aerojet RBCC concept integrates small rocket thrusters into the rearfacing base area of struts placed in the flowpath of a scramjet (Supersonic Combusting Ramjet) engine. In one mode of operation, at vehicle takeoff, the rockets provide the primary thrust with additional thrust coming from an ejector effect as air is drawn into the engine inlet, entrained, and accelerated by the rocket exhaust.

Glenn, Dennis E.↗

NASA NTRS2021

Flight Demonstration of the Tailored Arrival Manager

A flight demonstration of arrival traffic management automation was conducted in partnership between NASA, FAA and Boeing as an element of the latter’s ecoDemonstrator2020 flight program. For the demonstration, NASA’s prototype Tailored Arrival Manager(TAM) was used to compute efficient trajectory-based solutions to traffic management problems representing those encountered during time-based metering operations today. TAM solutions involving route modifications were uplinked to a Boeing 787 airplane using Controller Pilot Data Link Communications and seamlessly loaded into the airplane’s Flight Management System (FMS). The paper describes the concept and technology behind TAM along with the data exchanges and procedures involved with the demonstration. All TAM solutions were delivered in a timely manner and successfully integrated with the airplane’s FMS, thereby demonstrating the basic feasibility of trajectory-based arrival management using currently available data communications and avionics equipage. Although TAM solutions were not executed during this initial demonstration, a limited study of trajectory prediction accuracy was possible given that the airplane flew uninterrupted, automated descents with known route and speed intent. Analysis revealed that TAM meter-fix arrival time predictions were accurate to within ± 30 seconds for time horizons of 30 minutes or less, which matched closely with FMS predictions acquired through real-time data exchange. Top-of-descent predictions over similar time horizons were found accurate to within ± 5 nautical miles.

air traffic management↗

NASA NTRSDate not supplied

Flight Demonstration of the Tailored Arrival Manager

Air traffic managment↗

NASA NTRS1986

A reliable pipelining protocol for the message service of the Mobile Satellite Experiment

This paper describes and analyzes a pipelining protocol for the data message communications of MSAT-X, a proposed experimental satellite-based mobile communications network. A demand assigned multiple access protocol using pure ALOHA for making reservation requests has been developed for MSAT-X under error-free assumptions. Preliminary propagation studies indicate that the short term bit error rate of satellite channels in a mobile environment can be as high as 0.001. Therefore, error-control schemes must be developed to ensure reliable transmissions. A retransmission scheme using selective repeat to minimize the end-to-end delay is proposed. Slotted ALOHA for making reservation requests is used to increase the overall system throughput. Since the number of channels available for reservation and data channels is essentially fixed for a given voice call blocking probability and a fixed call arrival rate, the analysis presented in this paper is also applicable to the integrated voice and data services of MSAT-X. Various operational scenarios have been investigated.

Li, V. O. K.↗