Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Buckling of a fiber bundle embedded in epoxy

Buckling of a fiber bundle embedded in epoxy resin was studied to gain insight into compressive failure mechanisms in unidirectional composites. The fibers used were E-glass, T300 graphite, T700 graphite, and P75 graphite. These fibers were combined with two different resins: Epon 815/V140 and Epon 828/Z. In both resins the failure mode of the bundle was found to be microbuckling of fibers for the first three types of fibers; however, the high-modulus P75 fibers failed in shear without any sign of microbuckling. The strains at which microbuckling occurred were higher than the compressive failure strains of the corresponding unidirectional composites. In the soft resin, Epon 815/V140, fibers buckled at lower strains than in the stiff resin, Epon 828/Z. The buckling strains and the segment lengths followed the trends predicted for a single filament embedded in an infinite matrix.

Hahn, H. T.↗
NASA NTRS1987

Tensile behavior of glass/ceramic composite materials at elevated temperatures

This paper describes the tensile behavior of high-temperature composite materials containing continuous Nicalon ceramic fiber reinforcement and glass and glass/ceramic matrices. The longitudinal properties of these materials can approach theoretical expectations for brittle matrix composites, failing at a strength and ultimate strain level consistent with those of the fibers. The brittle, high-modulus matrices result in a nonlinear stress-strain curve due to the onset of stable matrix cracking at 10 to 30 percent of the fiber strain to failure, and at strains below this range in off-axis plies. Current fibers and matrices can provide attractive properties well above 1000 C, but composites experience embrittlement in oxidizing atmospheres at 800 to 1000 C due to oxidation of a carbon interface reaction layer.The oxidation effect greatly increases the interface bond strength, causing composite embrittlement.

Mandell, J. F.↗
NASA NTRS1986

Mechanical properties characterization of composite sandwich materials intended for space antenna applications

The composite materials proposed for use in the Advanced Communications Technology Satellite (ACTS) Program contains a new, high modulus graphite fiber as the reinforcement. A study was conducted to measure certain mechanical properties of the new fiber-reinforced material as well as of a composite-faced aluminum honeycomb sandwich structure. Properties were measured at -157, 22, and 121 C. Complete characterization of this material was not intended. Longitudinal tensile, picture-frame shear, short-beam shear, and flexural tests were performed on specimens of the composite face-sheet materials. Unidirectional, cross-plied, and quasi-isotropic fiber composite ply layup designs were fabricated and tested. These designs had been studied by using NASA's Integrated Composite Analyzer (ICAN) computer program. Flexural tests were conducted on (+/- 60/0 deg) sub s composite-faced sandwich structure material. Resistance strain gages were used to measure strains in the tensile, picture-frame, and sandwich flexural tests. The sandwich flexural strength was limited by the core strength at -157 and 22 C. The adhesive bond strength was the limiting factor at 121 C. Adhesive mechanical properties are reflected in sandwich structure flexural properties when the span-to-depth ratio is great enough to allow a significant shear effect on the load-deflection behavior of the sandwich beam. Most measured properties agreed satisfactorily with the properties predicted by ICAN.

Bowles, Kenneth J.↗
NASA NTRS1988

Novel polyamide-imines

An account is given of tough, thermally stable linear polyimides containing amide linkages that recommend themselves for use in high temperature-resistant films and coatings as well as matrix resins for graphite-reinforced structures. Four such polymers were synthesized from unsubstituted amide diamines, and two others from N-substituted amide diamines. High inherent viscosities and glass transition temperatures were obtained. The films exhibit good resistance to organic solvents. Films of the 4,4-prime-isomer polyamide-imide yielded exceptionally high modulus and toughness during impact evaluation.

Dezern, James F.↗
NASA NTRS1989

A comparison of two trusses for the space station structure

The structural performance of two truss configurations, the orthogonal tetrahedral and a Warren-type, are compared using finite element models representing the November Reference Phase 1 Space Station. The truss torsional stiffness properties and fundamental torsion frequency are determined using cantilever truss-beam models. Frequencies, mode shapes, transient response, and truss strut compressive loads are compared for the two space station models. The performance benefit resulting from using a high modulus truss strut is also presented. Finally, assembly and logistics characteristics of the two truss configurations are evaluated.

Sutter, Thomas R.↗
NASA NTRS1988

An experimental investigation of the fracture behavior of thick, notched laminated composites

The fracture of high-modulus fiber-reinforced graphite/epoxy laminates with machined crack-like notches is discussed. An experimental program was conducted, in which stacking sequence,laminate thickness, notch size, and specimen configuration have been investigated. This research has led to the fundamental observation that heterogeneity significantly effects the fracture of thin laminates but has a relatively insignificant effect on the fracture of thick laminates. The results of this program are reviewed with the emphasis on the notch sensitivity and design of thick laminates.

Harris, Charles E.↗
NASA NTRS1989

Mechanical properties characterization of composite sandwich materials intended for space antenna applications

The composite materials proposed for use in the Advanced Communications Technology Satellite (ACTS) program contains a new, high modulus graphite fiber as the reinforcement. A study was conducted to measure certain mechanical properties of the new fiber-reinforced material as well as of a composite-faced aluminum honeycomb sandwich structure. Properties were measured at -157, 22, and 121 C. Complete characterization of this material was not intended. Longitudinal tensile, picture-frame shear, short-beam shear, and flexural tests were performed on specimens of the composite face-sheet materials. Unidirectional, cross-plied, and quasi-isotropic fiber composite ply layup designs were fabricated and tested. These designs had been studied by using NASA's Integrated Composite Analyzer (ICAN) computer program. Flexural tests were conducted on (+/- 60/0 deg) sub s composite-faced sandwich structure material. Resistance strain gages were used to measure strains in the tensile, picture-frame, and sandwich flexural tests. The sandwich flexural strength was limited by the core strength at 157 and 22 c. The adhesive bond strength was the limiting factor at 121 C. Adhesive mechanical properties are reflected in sandwich structure flexural properties when the span-to-depth ratio is great enough to allow a significant shear effect on the load-deflection behavior of the sandwich beam. Most measured properties agreed satisfactorily with the properties predicted by ICAN.

Bowles, Kenneth J.↗
NASA NTRS1990

Optimal fabrication processes for unidirectional metal-matrix composites: A computational simulation

A method is proposed for optimizing the fabrication process of unidirectional metal matrix composites. The temperature and pressure histories are optimized such that the residual microstresses of the composite at the end of the fabrication process are minimized and the material integrity throughout the process is ensured. The response of the composite during the fabrication is simulated based on a nonlinear micromechanics theory. The optimal fabrication problem is formulated and solved with non-linear programming. Application cases regarding the optimization of the fabrication cool-down phases of unidirectional ultra-high modulus graphite/copper and silicon carbide/titanium composites are presented.

Saravanos, D. A.↗
NASA NTRS1989

Fiber-matrix interface failures

Interface fractures of aluminum-graphite composites under transverse loading are expected to occur within the graphite fibers, but very near the interface. Residual stresses in aluminum, reinforced with the new high modulus pitch-based fibers, are much lower than would be expected based on simple elasticity calculations. The excess stress may be relaxed by shearing internal to the fibers or at the interface rather than by plastic flow of the matrix. The internal shearing also occurs during repeated thermal cycling of these composites; the fibers are repeatedly intruded, then extruded, during repeated temperature excursions.

Rabenberg, Lew↗
NASA NTRS1989

Measurements of print-through in graphite fiber epoxy composites

High-reflectance accurate-contour mirrors are needed for solar dynamic space power systems. Graphite fiber epoxy composites are attractive candidates for such applications owing to their high modulus, near-zero coefficient of thermal expansion, and low mass. However, mirrors prepared from graphite fiber epoxy composite substrates often exhibit print-through, a distortion of the surface, which causes a loss in solar specular reflectance. Efforts to develop mirror substrates without print-through distortion require a means of quantifying print-through. Methods have been developed to quantify the degree of print-through in graphite fiber epoxy composite specimens using surface profilometry.

Jaworske, Donald A.↗
NASA NTRS1989

Guided waves and defect scattering in metal matrix composite plates

Guided Rayleigh-Lamb waves in a continuous graphite fiber reinforced magnesium plate has been studied. The interest in this material arises from its high thermal stability and because it provides high strength-to-weight ratio. Previous studies have shown that for wavelengths much larger than the fiber diameters and spacing, the material can be characterized as transversely isotropic with the symmetry axis aligned with the fiber direction. Because of the high longitudinal stiffness of the graphite fibers, the material shows strong anisotropy, with very high modulus in the fiber direction. For this reason, dispersion of guided waves is strongly influenced by the deviation of the direction of propagation from the symmetry axis. Results are given for propagation in different directions and for scattering of antiplane shear waves by surface-breaking cracks and delaminations.

Datta, Subhendu K.↗
NASA NTRS1990

Optimal fabrication processes for unidirectional metal-matrix composites - A computational simulation

A method is proposed for optimizing the fabrication process of unidirectional metal matrix composites. The temperature and pressure histories are optimized such that the residual microstresses of the composite at the end of the fabrication process are minimized and the material integrity throughout the process is ensured. The response of the composite during the fabrication is simulated based on a nonlinear micromechanics theory. The optimal fabrication problem is formulated and solved with nonlinear programming. Application cases regarding the optimization of the fabrication cool-down phases of unidirectional ultra-high modulus graphite/copper and silicon carbide/titanium composites are presented.

Saravanos, D. A.↗
NASA NTRS1991

Vacuum Powder Injector

Method developed to provide uniform impregnation of bundles of carbon-fiber tow with low-solubility, high-melt-flow polymer powder materials to produce composite prepregs. Vacuum powder injector expands bundle of fiber tow, applies polymer to it, then compresses bundle to hold powder. System provides for control of amount of polymer on bundle. Crystallinity of polymer maintained by controlled melt on takeup system. All powder entrapped, and most collected for reuse. Process provides inexpensive and efficient method for making composite materials. Allows for coating of any bundle of fine fibers with powders. Shows high potential for making prepregs of improved materials and for preparation of high-temperature, high-modulus, reinforced thermoplastics.

Working, Dennis C.↗
NASA NTRS1990

Intercalated graphite fiber composites as EMI shields in aerospace structures

The requirements for electromagnetic interference (EMI) shielding in aerospace structures are complicated over that of ground structures by their weight limitations. As a result, the best EMI shielding materials must blend low density, high strength, and high elastic modulus with high shielding ability. In addition, fabrication considerations including penetrations and joints play a major role. The EMI shielding properties are calculated for shields formed from pristine and intercalated graphite fiber/epoxy composites and compared to preliminary experimental results and to shields made from aluminum. Calculations indicate that EMI shields could be fabricated from intercalated graphite composites which would have less than 12 percent of the mass of conventional aluminum shields, based on mechanical properties and shielding properties alone.

Gaier, James R.↗
NASA NTRS1990

Effects of cure temperature, electron radiation, and thermal cycling on P75/930 composites

Graphite/epoxy composites are candidates for future space structures due to high stiffness and dimensional stability requirements of these structures. Typical graphite/epoxy composites are brittle and have high residual stresses which often result in microcracking during the thermal cycling typical of the space environment. Composite materials used in geosynchronous orbit applications will also be exposed to high levels of radiation. The purpose of the present study was to determine the effects of cure temperature and radiation exposure on the shear strength and thermal cycling-induced microcrack density of a high modulus, 275 F cure epoxy, P75/930. The results from the P75/930 are compared to previously reported data on P75/934 and T300/934 where 934 is a standard 350 F cure epoxy. The results of this study reveal that P75/930 is significantly degraded by total doses of electron radiation greater than 10(exp 8) rads and by thermally cycling between -250 F and 150 F. The P75/930 did not have improved microcrack resistance over the P75/934, and the 930 resin system appears to be more sensitive to electron radiation-induced degradation than the 934 resin system.

Funk, Joan G.↗
NASA NTRS1990

A study of fracture mechanisms in ATD roller bearing

The purpose was to investigate how microstructures, especially anisotropy, affects internal stresses and the overall mechanical response of bearings. Samples with the stress axis along the aligned carbide direction possessed high modulus values compared to those with their axis perpendicular to the carbide stringers. The difference in the modulus was found to be more than a factor of two. A series of experiments was conducted on rolled samples to further investigate this effect; the two sets of results were consistent with each other. The degree of anisotropy of the microstructure in terms of the carbide and matrix orientations was determined using x-ray diffraction. The stress state determination was conducted using neutron diffraction. It was found that there was little variation in the distribution of the internal stresses amongst different samples, indicating that small changes in the processing and geometrical conditions did not result in significant variations in the internal stress. A nominal tensile hoop stress of 39 ksi was obtained for the inner raceway. Furthermore, during the course of the investigation, it was apparent that there was a need to determine the stress state induced by the shrink fitting process. Therefore, a series of experiments was conducted using strain gages to identify the stress distribution in a shrink fitting process in three different types of geometries. Correlations were obtained to estimate the highest stress values in the outer and inner groove geometry. A finite element program based on the ANSYS system was developed to compute the stress distribution in the inner raceway geometry. This analysis indicates that the highest tensile stress in the system occurs at the ID of the ring with a stress value of over 5 times that of the applied radial stress. Results from all these facets were correlated with one another. It appears that the material does not fail as a result of any one single factor, but results from a combination of the various factors investigated.

Zee, Ralph H.↗
NASA NTRS1990

Acetylene-chromene terminated resins as high temperature thermosets

A novel phase transfer catalyzed process for the preparation of propargyl ethers has been developed. The propargyl ethers serve as precursors to a new class of thermosetting resins called acetylene-chromene terminated (ACT) resins. Heat treatment of a solution of propargyl ethers with various catalysts, followed by removal of solvent leads to the ACT resins via partial conversion of the propargyl ether groups to chromenes. This process reduces the energy content of the resin systems and reduces the amount of shrinkage found during cure. Due to the presence of the solvent the process is safe and gives rise to low viscosity products suitable for resin transfer molding and filament winding type applications. Due to the high glass transition temperature, high modulus, and low moisture uptake the cured resins display better than 232 C/wet performance. The thermal stability of the ACT resins in air at 204 C is superior to that of conventional bismaleimide resins. The resins also display excellent electrical properties.

Godschalx, J. P.↗
NASA NTRS1991

Pultrusion process characterization

Pultrusion is a process through which high-modulus, lightweight composite structural members such as beams, truss components, stiffeners, etc., are manufactured. The pultrusion process, though a well-developed processing art, lacks a fundamental scientific understanding. The objective here was to determine, both experimentally and analytically, the process parameters most important in characterizing and optimizing the pultrusion of uniaxial fibers. The effects of process parameter interactions were experimentally examined as a function of the pultruded product properties. A numerical description based on these experimental results was developed. An analytical model of the pultrusion process was also developed. The objective of the modeling effort was the formulation of a two-dimensional heat transfer model and development of solutions for the governing differential equations using the finite element method.

Vaughan, James G.↗