Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high frequency testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Acoustic power dissipation on radiation through duct terminations - Experiments

This paper describes the acoustic transmission characteristics of ducts, nozzles, orifices, and perforated plates, studied under an experimental program using an acoustic impulse technique. In this technique high intensity pulses, generated by discharging a capacitor across a spark gap, were used as the sound source. The test conditions include heated and unheated flows, with and without simulated flight. Results for a straight round duct, three convergent nozzles, a suppressor nozzle, 12 orifice plates, and 10 perforated plates are presented. A low frequency acoustic power loss phenomenon was observed for all configurations at all test conditions including the no flow condition. It was suspected that the power loss phenomenon at the no flow condition could be due to the conversion of acoustic energy into vortical energy due to non-linear propagation of high intensity pulses. However, a small amount of low frequency power loss was noticed even when tests were repeated with a low intensity sound. Detailed flow visualization results were also obtained to complement the acoustic results.

Salikuddin, M.↗
NASA NTRS1991

Lightning induced currents in aircraft wiring using low level injection techniques

Various techniques were studied to predict the transient current induced into aircraft wiring bundles as a result of an aircraft lightning strike. A series of aircraft measurements were carried out together with a theoretical analysis using computer modeling. These tests were applied to various aircraft and also to specially constructed cylinders installed within coaxial return conductor systems. Low level swept frequency CW (carrier waves), low level transient and high level transient injection tests were applied to the aircraft and cylinders. Measurements were made to determine the transfer function between the aircraft drive current and the resulting skin currents and currents induced on the internal wiring. The full threat lightning induced transient currents were extrapolated from the low level data using Fourier transform techniques. The aircraft and cylinders used were constructed from both metallic and CFC (carbon fiber composite) materials. The results show the pulse stretching phenomenon which occurs for CFC materials due to the diffusion of the lightning current through carbon fiber materials. Transmission Line Matrix modeling techniques were used to compare theoretical and measured currents.

Stevens, E. G.↗
NASA NTRS1980

Experimental determination of unsteady blade element aerodynamics in cascades. Volume 1: Torsion mode cascade

A two dimensional cascade of harmonically oscillating airfoils was designed to model a near tip section from a rotor which was known to have experienced supersonic torsional flutter. This five bladed cascade had a solidity of 1.17 and a setting angle of 1.07 rad. Graphite epoxy airfoils were fabricated to achieve the realistically high reduced frequency level of 0.44. The cascade was tested over a range of static pressure ratios approximating the blade element operating conditions of the rotor along a constant speed line which penetrated the flutter boundary. The time-steady and time-unsteady flow field surrounding the center cascade airfoil were investigated. The effects of reduced solidity and decreased setting angle on the flow field were also evaluated.

Riffel, R. E.↗
NASA NTRS1980

Experimental determination of unsteady blade element aerodynamics in cascades. Volume 2: Translation mode cascade

A two dimensional cascade of harmonically oscillating airfoils was designed to model a near tip section from a rotor which was known to have experienced supersonic translational model flutter. This five bladed cascade had a solidity of 1.52 and a setting angle of 0.90 rad. Unique graphite epoxy airfoils were fabricated to achieve the realistic high reduced frequency level of 0.15. The cascade was tested over a range of static pressure ratios approximating the blade element operating conditions of the rotor along a constant speed line which penetrated the flutter boundary. The time steady and time unsteady flow field surrounding the center cascade airfoil were investigated.

Riffel, R. E.↗
NASA NTRS1986

The Provence ST radar

Since the Alpex Campaign, when 3 Stratosphere-Troposphere (ST) radar operated in Camarque as a cooperative effort of the Aeronomy Laboratory of NOAA, CO, and LSEET from Toulon, a 50 MHz Very High Frequency (VHF) ST radar was developed, improved, and tested. The operating characteristics, main objectives, preliminary results, and future experiment costs of the VHF ST radar are discussed.

Crochet, M.↗
NASA NTRS2001

A Rover Deployed Ground Penetrating Radar on Mars

Radar is a fundamental tool capable of addressing a variety of geological problems on Mars via collection of data suitable for interpreting variations in surface morphology and reflectivity. Surface-deployed ground penetrating radar (GPR) can help further constrain the geology and structure of the near surface of Mars by directly measuring the range and character of in situ radar properties. In recognition of this potential, a miniaturized, easily modified GPR is being developed for possible deployment on a future Mars rover and will enable definition of radar stratigraphy at high spatial resolution to depths of 10-20 meters. Ongoing development of a Mars impulse GPR with industry partners at Geophysical Survey Systems, Inc., focuses on design and testing of a prototype transducer array (with both high frequency bistatic and low frequency monostatic components) in parallel with fabrication of a low power, mass, and volume control unit. The operational depth of 10-20 meters is geared towards definition of stratigraphy, subsurface blocks, and structure at the decimeter to meter scale that is critical for establishing the geologic setting of the rover. GPR data can also be used to infer the degree of any post-depositional pedogenic alteration or weathering that has subsequently taken place, thereby enabling assessment of pristine versus secondary morphology at the landing site. As is the case for most remote sensing instruments, a GPR may not detect water unambiguously. Nevertheless, any local, near-surface occurrence of liquid water will lead to large, easily detected dielectric contrasts. Moreover, definition of stratigraphy and setting will help in evaluating the history of aqueous activity and where any water might occur and be accessible. Most importantly perhaps, GPR can provide critical context for other rover and orbital instruments/data sets. Hence, GPR deployment along well positioned transects in the vicinity of a lander should enable 3-D mapping of stratigraphy and could serve to guide direct subsurface sampling. Additional information is contained in the original extended abstract.

Grant, J. A.↗
NASA NTRS1991

Evaluation of components, subsystems, and networks for high rate, high frequency space communications

The development of new space communications technologies by NASA has included both commercial applications and space science requirements. NASA's Systems Integration, Test and Evaluation (SITE) Space Communication System Simulator is a hardware based laboratory simulator for evaluating space communications technologies at the component, subsystem, system, and network level, geared toward high frequency, high data rate systems. The SITE facility is well-suited for evaluation of the new technologies required for the Space Exploration Initiative (SEI) and advanced commercial systems. Described here are the technology developments and evaluation requirements for current and planned commercial and space science programs. Also examined are the capabilities of SITE, the past, present and planned future configurations of the SITE facility, and applications of SITE to evaluation of SEI technology.

Kerczewski, Robert J.↗
NASA NTRSDate not supplied

Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements for the NASA Unitary Plan Wind Tunnel Tests

This paper discusses the Dynamic Mode Decomposition (DMD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected with four Phantom high-speed cameras at a constant sample frequency in the Ascent Transient Aerodynamics Test (ATAT) of the Space Launch System (SLS) Block 1 cargo vehicle with the Unitary Plan Wind Tunnel (UPWT) 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The conventional DMD algorithm is based on the Singular Value Decomposition (SVD). For the data with zero mean, the DMD is equivalent to the Discrete Fourier Transform (DFT). Since the uPSP is mainly used to determine the unsteady property of the aerodynamic flow, the DMD of the uPSP measurements is implemented in two steps: (1) subtract the mean value from the uPSP measurement; (2) apply the Fast Fourier Transform (FFT) on the resulting data with zero mean. The DMD of the uPSP measurements with FFT has two advantages: (1) the FFT algorithm is well known for its computational efficiency, therefore, compared to the SVD-based DMD algorithm, the DMD with FFT reduces the computation time; (2) the DMD with FFT can be easily implemented in parallel processing. The DMD outputs were generated with the execution in parallel of a code in C, with libraries of FFTW for FFT and MPI/OpenMP for parallel processing, on the NASA Pleiades supercomputer. In this paper, the results of DMD of the uPSP measurements in the tests of Mach sweep runs of the SLS ATAT are presented, and the effectiveness of the DMD of the uPSP measurements in the diagnosis of the unsteady, aerodynamic phenomena is demonstrated. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding for this research was provided by the NASA Aeroscience Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗
NASA NTRS1981

Radiation losses in resonant tubes

The role of radiation losses in a resonant tube - the transfer of sound energy from the test gas through the confines of the tube to the ambient atmosphere - is investigated both theoretically and experimentally. It is concluded that losses of this sort make no noticeable contribution to the background losses, even at high gas pressures. Nevertheless, if an axial resonant frequency of the test gas closely matches a longitudinal resonant frequency of the tube wall, the internal sound pressure can excite tube displacements of disproportionate magnitude and thus cause excessive losses, not due to radiation but rather to frictional dissipation related to the motion of the tube structure. This mechanism is effective when the mode numbers of the gas and tube have opposite parity, and makes sound absorption measurements at the fundamental gas frequency particularly problematical. An experimental investigation confirms the existence of such additional losses when the parity condition is fulfilled.

Zuckerwar, A. J.↗
NASA NTRS1987

Effect of helicopter blade dynamics on blade aerodynamic and structural loads

The effect of rotor blade dynamics on aerodynamic and structural loads is examined for a conventional, main-rotor helicopter using a comprehensive rotorcraft analysis (CAMRAD) and flight-test data. The impact of blade dynamics on blade section lift-coefficient time histories is studied by comparing predictions from a rigid-blade analysis and an elastic-blade analysis with helicopter flight test data. The elastic blade analysis better predicts high-frequency behavior of section lift. In addition, components of the blade angle of attack such as elastic blade twist, blade flap rate, blade slope velocity, and inflow are examined as a function of blade mode. Elastic blade motion changed blade angle of attack by a few tenths of a degree, and up to the sixth rotor harmonic. A similar study of the influence of blade dynamics on bending and torsion moments was also conducted. A correlation study comparing predictions from several elastic-blade analyses with flight-test data revealed that an elastic-blade model consisting of only three elastic bending modes (first and second flap and first lag), and two elastic torsion modes was sufficient for good correlation.

Heffernan, Ruth M.↗
NASA NTRSDate not supplied

Analysis of Dynamic Mode Decomposition Outputs of Unsteady Pressure-Sensitive Paint Measurements in the NASA Wind Tunnel Tests

This paper discusses the Dynamic Mode Decomposition (DMD) outputs of the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected with four Phantom high-speed cameras at a constant sample frequency in the Ascent Transient Aerodynamics Test (ATAT) of the Space Launch System (SLS) Block 1 cargo vehicle in the 11-by-11-foot transonic test section of the Unitary Plan Wind Tunnel (UPWT) at NASA Ames Research Center in September 2019. In this paper, the effectiveness to use the DMD outputs of uPSP measurements in the diagnosis and analysis of the aerodynamic and acoustic phenomena in the SLS ATAT is demonstrated. The work described in the paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities (AETC) Project.

acoustics↗
NASA NTRS1975

Reduction of noise from a fan stage for a turbofan engine by use of long-chord acoustically-treated stator vanes

A set of acoustically-treated long-chord vanes was designed to replace the vanes in an existing fan stage to investigate the noise reduction possibilities of both increased stator chord length and this method of incorporating acoustic damping material. The vanes were tested with both active and inactive acoustic surfaces. The inactive tests showed significant broadband noise effects with noise reductions in the middle to high frequencies and an increase at low frequencies. No reduction in blade passage tone was observed, but decreases in the overtones were observed. The tests with the active acoustic treatment showed large noise reductions over a wide frequency range.

Dittmar, J. H.↗
NASA NTRS2014

Level of Automation and Failure Frequency Effects on Simulated Lunar Lander Performance

A human-in-the-loop experiment was conducted at the NASA Ames Research Center Vertical Motion Simulator, where instrument-rated pilots completed a simulated terminal descent phase of a lunar landing. Ten pilots participated in a 2 x 2 mixed design experiment, with level of automation as the within-subjects factor and failure frequency as the between subjects factor. The two evaluated levels of automation were high (fully automated landing) and low (manual controlled landing). During test trials, participants were exposed to either a high number of failures (75% failure frequency) or low number of failures (25% failure frequency). In order to investigate the pilots' sensitivity to changes in levels of automation and failure frequency, the dependent measure selected for this experiment was accuracy of failure diagnosis, from which D Prime and Decision Criterion were derived. For each of the dependent measures, no significant difference was found for level of automation and no significant interaction was detected between level of automation and failure frequency. A significant effect was identified for failure frequency suggesting failure frequency has a significant effect on pilots' sensitivity to failure detection and diagnosis. Participants were more likely to correctly identify and diagnose failures if they experienced the higher levels of failures, regardless of level of automation

performance↗
NASA NTRS1992

Acoustical evaluation of the NASA Lewis 9 by 15 foot low speed wind tunnel

The test section of the NASA Lewis 9- by 15-Foot Low Speed Wind Tunnel was acoustically treated to allow the measurement of acoustic sources located within the tunnel test section under simulated free field conditions. The treatment was designed for high sound absorption at frequencies above 250 Hz and to withstand tunnel airflow velocities up to 0.2 Mach. Evaluation tests with no tunnel airflow were conducted in the test section to assess the performance of the installed treatment. This performance would not be significantly affected by low speed airflow. Time delay spectrometry tests showed that interference ripples in the incident signal resulting from reflections occurring within the test section average from 1.7 dB to 3.2 dB wide over a 500 to 5150 Hz frequency range. Late reflections, from upstream and downstream of the test section, were found to be insignificant at the microphone measuring points. For acoustic sources with low directivity characteristics, decay with distance measurements in the test section showed that incident free field behavior can be measured on average with an accuracy of +/- 1.5 dB or better at source frequencies from 400 Hz to 10 kHz. The free field variations are typically much smaller with an omnidirectional source.

Dahl, Milo D.↗
NASA NTRS2005

Development and Characterization Testing of an Air Pulsation Valve for a Pulse Detonation Engine Supersonic Parametric Inlet Test Section

In pulse detonation engines, the potential exists for gas pulses from the combustor to travel upstream and adversely affect the inlet performance of the engine. In order to determine the effect of these high frequency pulses on the inlet performance, an air pulsation valve was developed to provide air pulses downstream of a supersonic parametric inlet test section. The purpose of this report is to document the design and characterization tests that were performed on a pulsation valve that was tested at the NASA Glenn Research Center 1x1 Supersonic Wind Tunnel (SWT) test facility. The high air flow pulsation valve design philosophy and analyses performed are discussed and characterization test results are presented. The pulsation valve model was devised based on the concept of using a free spinning ball valve driven from a variable speed electric motor to generate air flow pulses at preset frequencies. In order to deliver the proper flow rate, the flow port was contoured to maximize flow rate and minimize pressure drop. To obtain sharp pressure spikes the valve flow port was designed to be as narrow as possible to minimize port dwell time.

Tornabene, Robert↗
NASA NTRS1987

Effect of Helicopter Blade Dynamics on Blade Aerodynamic and Structural Loads

The effect of rotor blade dynamics on aerodynamic and structural loads is examined for a conventional, main- rotor helicopter using both a comprehensive rotorcraft analysis (CAMRAD) and night test data. The impact of blade dynamics on blade section lift-coefficient time histories is studied by comparing predictions from both a rigid blade analysis and an elastic blade analysis with helicopter flight test data. The elastic blade analysis better predicts high-frequency behavior of section lift. In addition, components of the blade angle of attack, such as elastic blade twist, blade nap rate, blade slope velocity, and inflow, are examined as a function of blade mode. Elastic blade motion affects the blade angle of attack by a few tenths of a degree, and up to the sixth rotor harmonic. A similar study of the influence of blade dynamics on bending and torsion moments was also conducted. The modal analysis of the predicted blade structural loads suggested that five elastic bending deg of freedom (four flap and one lag) and three elastic torsion deg of freedom contributed to calculations of the blade structural loads. However, when structural bending load predictions from several elastic blade analyses were compared with flight test data, an elastic blade model consisting of only three elastic bending modes (first and second flap, and first lag), and two elastic torsion modes was found to be sufficient for maximum correlation.

Heffernan, Ruth M.↗
NASA NTRS1993

Spacecraft signal sources portable test system

There is a frequent need to measure the frequency stability and phase noise levels of very high performance signal sources that are required for certain spacecraft missions. These measurements need to be done at different locations as the spacecraft subsystems progress through the various stages of development, assembly, test, and integration. Allan Deviation and Phase Noise of high performance sources are generally measured by comparing the unit under test to a reference standard. Five basic requirements are associated with making these kind of measurements: (1) the reference standard performance needs to be equal or better than the unit under test; (2) the measurement system needs to accommodate odd, nonstandard measurement frequencies that can range from 4 MHz to 35 GHz; (3) warm-up frequency drift and aging can corrupt a measurement and must be dealt with; (4) test equipment generated noise must be understood and prevented from limiting the measurements; (5) test equipment noise performance must be verifiable in the field as needed. A portable measurement system that was built by JPL and used in the field is described. The methods of addressing the above requirements are outlined and some measurement noise floor values are given. This test set was recently used to measure state of the art crystal oscillator frequency standards on the TOPEX and MARS OBSERVER spacecraft during several stages of acceptance tests.

Kirk, Albert↗