SEARCH · Engineering Papers

Results for “gust load control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2010

Orion Touchdown Heading Control

At touchdown Orion must be aligned so that the crew person's feet are forward in the direction of the horizontal velocity. To ensure that this requirement is met active heading control is being implemented on the Orion crew module. This technique reduces probability of roll-over during splashdown, assures axial loads on the crew at touchdown, and alleviates structural requirements on impact allowing for a light-weight structural design. On-board sensors are used to measure current vehicle orientation and horizontal velocity used in generation of the heading error signal. Linear velocity measured by the IMU drifts while under parachutes due to wind gusts and has to be corrected by GPS; this makes GPS critical for successful landing. Jet fire logic is achieved by use of a phase-plane and commands are realized by using roll jets from the reaction control system (RCS); using pre existing hardware eliminates additional hardware and structural requirements. Touchdown performance is measured by an orientation envelope that was co-developed with structures so that the performance requirements overlap adding system redundancy. Heading control also introduces new difficulties to be addressed such as parachute line twist torque as well as increasing vehicle sensitivity to wind shifts and sea states. Solving these difficulties requires added complexity to flight software as well as increasing the propellant required to achieve successful touchdown. while offering promising results, the criticality of GPS along with a significant propellant cost raises questions on the effectiveness of using touchdown heading control.

Kane, Mark A.↗

NASA NTRS2018

Active In-Flight Load Redistribution Utilizing Fiber-Optic Shape Sensing and Multiple Control Surfaces

Morphing wing technologies have gained research interest in recent years as technological advancements pave the way for such innovations. A key benefit of such a morphing wing concept is the ability of the wing to transition into an optimal configuration at multiple flight conditions. Such a morphing wing will have applications not only in drag reduction but also in flutter suppression and gust alleviation. By manipulating the wing geometry to match a given flight profile it is likely that the wing will yield increases in not just aerodynamic efficiency but also structural efficiency. These structurally efficient designs will likely rely on some type of structural sensing system which will ensure the wing maintains positive margins throughout its flight profile.

FOSS↗

NASA NTRS1974

Helicopter gust response characteristics including unsteady aerodynamic stall effects

The results of an analytical study to evaluate the general response characteristics of a helicopter subjected to various types of discrete gust encounters are presented. The analysis employed was a nonlinear coupled, multi-blade rotorfuselage analysis including the effects of blade flexibility and unsteady aerodynamic stall. Only the controls-fixed response of the basic aircraft without any aircraft stability augmentation was considered. A discussion of the basic differences between gust sensitivity of fixed and rotary wing aircraft is presented. The effects of several rotor configuration and aircraft operating parameters on initial gust-induced load factor and blade vibratory stress and pushrod loads are discussed.

Arcidiacono, P. J.↗

NASA NTRS1974

Lifting-surface theory for a semi-infinite wing in oblique gust

An unsteady lifting-surface theory is developed for the calculation of the airload on a semi-infinite-span thin wing in a compressible flow due to interaction with an oblique gust. By using the solutions obtained for a two-dimensional wing, the problem is formulated so that the unknown is taken to be the difference between the airload on the semi-infinite wing and that on a two-dimensional wing under the same gust conditions. Since this airload difference is nonzero only near the wing tip, the control points need be distributed in the tip region only; this significantly simplifies the numerical procedure. Results are presented for a wing with rectangular tip. The implication for noise and unsteady loads due to blade-vortex interaction for helicopter rotors is discussed.

Chu, S.↗

NASA NTRS2019

Performance Enhancement of the Flexible Transonic Truss-Braced Wing Aircraft Using Variable-Camber Continuous Trailing-Edge Flaps

Aircraft designers are to a growing extent using vehicle flexibility to optimize performance with objectives such as gust load alleviation and drag minimization. More complex aerodynamically optimized configurations may also require dynamic loads and perhaps eventually flutter suppression. This paper considers an aerodynamically optimized truss-braced wing aircraft designed for a Mach 0.745 cruise. The variable camber continuous trailing edge flap concept with a feedback control system is used to enhance aeroelastic stability. A linearized reduced order aerodynamic model is developed from unsteady Reynolds averaged Navier-Stokes simulations. A static output feedback controller is developed from that model. Closed-loop simulations using the reduced order aerodynamic model show that the controller is effective in stabilizing the vehicle dynamics.

Bartels, Robert E.↗

NASA NTRS1984

Design of a digital ride quality augmentation system for a commuter aircraft

Commuter aircraft with low wing loading that operate at low altitudes are particularly susceptible to unwanted accelerations caused by atmospheric gusts. This paper describes the design and analysis of a longitudinal digital Ride Quality Augmentation System (RQAS). The RQAS designs were conducted for a Cessna 402B aircraft using the flaps and the elevator as the control surfaces. The designs are generated using linear quadratic Gaussian theory and analyzed in both the time and frequency domains. Nominal designs are presented at five flight conditions that cover a total mission. Trade-off studies are conducted to investigate the effect of sample time, computational delay time, servo bandwidth and control power.

Hammond, T. A.↗

NASA NTRS1983

Interactions of airfoils with gusts and concentrated vortices in unsteady transonic flow

Unsteady interactions of concentrated vortices and distributed free-stream gusts with a stationary airfoil have been analyzed in two-dimensional transonic flow. A simple method of introducing such disturbances has been implemented numerically in the well-known transonic small-disturbance code LTRAN2, and calculations have been performed for two important classes of current aerodynamic problems. The first, which demonstrates many of the essential features of the interactions between helicopter rotor blades and their trailing-vortex wakes, is that of a discrete potential vortex convecting past an airfoil. The second is the response of a transonic airfoil to a transverse periodic gust, with and without the alleviation that can be achieved by the proper active control motion of a trailing-edge flap. In both cases, unsteady effects are found to play important roles in the shock-wave motion, in the overall flow-field development, and consequently, in the air loads on the airfoil.

Mccroskey, W. J.↗

NASA NTRS2012

ASCENT Program

The ASCENT program solves the three-dimensional motion and attendant structural loading on a flexible vehicle incorporating, optionally, an active analog thrust control system, aerodynamic effects, and staging of multiple bodies. ASCENT solves the technical problems of loads, accelerations, and displacements of a flexible vehicle; staging of the upper stage from the lower stage; effects of thrust oscillations on the vehicle; a payload's relative motion; the effect of fluid sloshing on vehicle; and the effect of winds and gusts on the vehicle (on the ground or aloft) in a continuous analysis. The ATTACH ASCENT Loads program reads output from the ASCENT flexible body loads program, and calculates the approximate load indicators for the time interval under consideration. It calculates the load indicator values from pre-launch to the end of the first stage.

Brown, Richard↗

NASA NTRS2016

Model Order Reduction of Aeroservoelastic Model of Flexible Aircraft

This paper presents a holistic model order reduction (MOR) methodology and framework that integrates key technological elements of sequential model reduction, consistent model representation, and model interpolation for constructing high-quality linear parameter-varying (LPV) aeroservoelastic (ASE) reduced order models (ROMs) of flexible aircraft. The sequential MOR encapsulates a suite of reduction techniques, such as truncation and residualization, modal reduction, and balanced realization and truncation to achieve optimal ROMs at grid points across the flight envelope. The consistence in state representation among local ROMs is obtained by the novel method of common subspace reprojection. Model interpolation is then exploited to stitch ROMs at grid points to build a global LPV ASE ROM feasible to arbitrary flight condition. The MOR method is applied to the X-56A MUTT vehicle with flexible wing being tested at NASA/AFRC for flutter suppression and gust load alleviation. Our studies demonstrated that relative to the fullorder model, our X-56A ROM can accurately and reliably capture vehicles dynamics at various flight conditions in the target frequency regime while the number of states in ROM can be reduced by 10X (from 180 to 19), and hence, holds great promise for robust ASE controller synthesis and novel vehicle design.

aeroelasticity↗

NASA NTRS2005

Motion Cueing Algorithm Development: Piloted Performance Testing of the Cueing Algorithms

The relative effectiveness in simulating aircraft maneuvers with both current and newly developed motion cueing algorithms was assessed with an eleven-subject piloted performance evaluation conducted on the NASA Langley Visual Motion Simulator (VMS). In addition to the current NASA adaptive algorithm, two new cueing algorithms were evaluated: the optimal algorithm and the nonlinear algorithm. The test maneuvers included a straight-in approach with a rotating wind vector, an offset approach with severe turbulence and an on/off lateral gust that occurs as the aircraft approaches the runway threshold, and a takeoff both with and without engine failure after liftoff. The maneuvers were executed with each cueing algorithm with added visual display delay conditions ranging from zero to 200 msec. Two methods, the quasi-objective NASA Task Load Index (TLX), and power spectral density analysis of pilot control, were used to assess pilot workload. Piloted performance parameters for the approach maneuvers, the vertical velocity upon touchdown and the runway touchdown position, were also analyzed but did not show any noticeable difference among the cueing algorithms. TLX analysis reveals, in most cases, less workload and variation among pilots with the nonlinear algorithm. Control input analysis shows pilot-induced oscillations on a straight-in approach were less prevalent compared to the optimal algorithm. The augmented turbulence cues increased workload on an offset approach that the pilots deemed more realistic compared to the NASA adaptive algorithm. The takeoff with engine failure showed the least roll activity for the nonlinear algorithm, with the least rudder pedal activity for the optimal algorithm.

Houck, Jacob A.↗

NASA NTRS1991

Maximized gust loads for a nonlinear airplane using matched filter theory and constrained optimization

This paper describes and illustrates two matched-filter-theory based schemes for obtaining maximized and time-correlated gust-loads for a nonlinear airplane. The first scheme is computationally fast because it uses a simple one-dimensional search procedure to obtain its answers. The second scheme is computationally slow because it uses a more complex multidimensional search procedure to obtain its answers, but it consistently provides slightly higher maximum loads than the first scheme. Both schemes are illustrated with numerical examples involving a nonlinear control system.

Scott, Robert C.↗

NASA NTRS1991

Maximized gust loads for a nonlinear airplane using matched filter theory and constrained optimization

Two matched filter theory based schemes are described and illustrated for obtaining maximized and time correlated gust loads for a nonlinear aircraft. The first scheme is computationally fast because it uses a simple 1-D search procedure to obtain its answers. The second scheme is computationally slow because it uses a more complex multi-dimensional search procedure to obtain its answers, but it consistently provides slightly higher maximum loads than the first scheme. Both schemes are illustrated with numerical examples involving a nonlinear control system.

Scott, Robert C.↗

NASA NTRS1976

Evaluating a CRT map predictor for airborne use

Six airline pilots participated in a fixed-base simulator experiment designed to study the advantages and disadvantages of incorporating a simple horizontal flight-path predictor on both fixed and rotating electronic CRT map displays. The pilots were asked to fly a modified 'figure eight' ground track while attempting to maintain constant altitude. All flight information was displayed on one 17-in. (43-cm) CRT monitor. The controlled variables were the map orientation, pilots, presence or absence of crosswinds, presence or absence of wind gusts, and presence or absence of predictor. Error scores were recorded as deviations from the commanded ground track and altitude. It was found that the predictor reduced deviations from the commanded ground track, narrowed performance differences among pilots, narrowed the error differences found with and without crosswinds, and decreased pilot work load.

Baty, D. L.↗

NASA NTRS2009

Vibration Challenges in the Design of NASA's Ares Launch Vehicles

This paper focuses on the vibration challenges inherent in the design of NASA s Ares launch vehicles. A brief overview of the launch system architecture is provided to establish the context for the discussion. Following this is a general discussion of the design considerations and analytical disciplines that are affected by vibration. The first challenge discussed is that of coupling between the vehicle flight control system and fundamental vibrational modes of the vehicle. The potential destabilizing influence of the vibrational dynamics is described along with discussion of the typical methods employed to overcome this issue. Next is a general discussion of the process for developing the design loads for the primary structure. This includes quasi-steady loads and dynamic loads induced by the structural dynamic response. The two principal parts of this response are the gust induced responses of the lower frequency modes and the buffet induced responses of the higher frequency modes. Structural dynamic model validation will also be addressed. Following this, discussions of three somewhat unique topics of Pogo Instability, Solid Booster Thrust Oscillation, and Liquid Rocket Engine Turbopump Rotordynamic Stability and Response are presented.

Ryan, Stephen G.↗

NASA NTRS1997

Aeroservoelastic and Structural Dynamics Research on Smart Structures Conducted at NASA Langley Research Center

An overview of smart structures research currently underway at the NASA Langley Research Center in the areas of aeroservoelasticity and structural dynamics is presented. Analytical and experimental results, plans, potential technology pay-offs, and challenges are discussed. The goal of this research is to develop the enabling technologies to actively and passively control aircraft and rotorcraft vibration and loads using smart devices. These enabling technologies and related research efforts include developing experimentally-validated finite element and aeroservoelastic modeling techniques; conducting bench experimental tests to assess feasibility and understand system trade-offs; and conducting large-scale wind tunnel tests to demonstrate system performance. The key aeroservoelastic applications of this research include: active twist control of rotor blades using interdigitated electrode piezoelectric composites and active control of flutter, and gust and buffeting responses using discrete piezoelectric patches. In addition, NASA Langley is an active participant in the DARPA/Air Force Research Laboratory/NASA/Northrop Grumman Smart Wing program which is assessing aerodynamic performance benefits using smart materials.

McGowan, Anna-Maria Rivas↗

NASA NTRS2012

Survey of Applications of Active Control Technology for Gust Alleviation and New Challenges for Lighter-weight Aircraft

This report provides a historical survey and assessment of the state of the art in the modeling and application of active control to aircraft encountering atmospheric disturbances in flight. Particular emphasis is placed on applications of active control technologies that enable weight reduction in aircraft by mitigating the effects of atmospheric disturbances. Based on what has been learned to date, recommendations are made for addressing gust alleviation on as the trend for more structurally efficient aircraft yields both lighter and more flexible aircraft. These lighter more flexible aircraft face two significant challenges reduced separation between rigid body and flexible modes, and increased sensitivity to gust encounters due to increased wing loading and improved lift to drag ratios. The primary audience of this paper is engineering professionals new to the area of gust load alleviation and interested in tackling the multifaceted challenges that lie ahead for lighter-weight aircraft.

Regan, Christopher D.↗

NASA NTRS2008

Challenges of Roll Orientation with Respect to Vehicle Heading at Touchdown for the Orion Command Module

Due to mass constraints, the Orion Command Module landing attention system requires that the capsule be oriented in a specific direction with respect to the horizontal surface-relative velocity (Heading) at touchdown in order to keep crew and vehicle loads within specifications. These constraints apply to both land and water landings. In fact, water landings are even more constrained with the addition of impact angle requirements necessary to slice through the water. There are two primary challenges with achieving this touchdown orientation: 1. Navigation knowledge of velocity (needed to determine Heading) with and without GPS, including the effects of the Heading angle itself becoming undefined as horizontal velocity decreases, and 2. Controlling to the desired orientation in the presences of chute torque and wind gusts that may change the Heading just prior to touchdown. This paper will discuss the design and performance of the current Orion navigation and control system used to achieve the desired orientation at touchdown.

Gay, Robert S.↗

NASA NTRS1981

Kaman 40 kW wind turbine generator - control system dynamics

The generator design incorporates an induction generator for application where a utility line is present and a synchronous generator for standalone applications. A combination of feed forward and feedback control is used to achieve synchronous speed prior to connecting the generator to the load, and to control the power level once the generator is connected. The dynamics of the drive train affect several aspects of the system operation. These were analyzed to arrive at the required shaft stiffness. The rotor parameters that affect the stability of the feedback control loop vary considerably over the wind speed range encountered. Therefore, the controller gain was made a function of wind speed in order to maintain consistent operation over the whole wind speed range. The velocity requirement for the pitch control mechanism is related to the nature of the wind gusts to be encountered, the dynamics of the system, and the acceptable power fluctuations and generator dropout rate. A model was developed that allows the probable dropout rate to be determined from a statistical model of wind gusts and the various system parameters, including the acceptable power fluctuation.

Perley, R.↗