Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Comparison of loads from HAWC2 and OpenFAST for the IEA Wind 15 MW Reference Wind Turbine

Reference wind turbines (RWTs) that reflect the state-of-the-art of current wind energy technology are necessary in order to properly evaluate innovative methods in wind turbine design and evaluation. The International Energy Agency (IEA) Wind Technology Collaboration Platform (TCP) Task 37 has recently developed a new RWT geared towards offshore floating-foundation applications: the IEA Wind 15 MW. The model has been implemented in two aeroelastic codes, OpenFAST and HAWC2, based on an underlying common ontology. However, these toolchains result in slightly different structural parameters, and the two codes utilise different structural models. Thus, to increase the utility of the model, it is necessary to compare the aeroelastic responses. This paper compares aeroelastic loads calculated using different fidelities of the blade model in OpenFAST (ElastoDyn and BeamDyn) and HAWC2 (prismatic Timoshenko without torsion and Timoshenko with fully populated stiffness matrix), where both codes use the DTU Basic controller and the same turbulence boxes to reduce discrepancies. The aeroelastic responses to steady wind, step wind and turbulent wind (per IEC 61400-1 wind class IB) are considered. The results indicate a generally good agreement between the loads dominated by aerodynamic thrust and force, especially for the no-torsion blade models. Discrepancies were observed in other load channels, partially due to differences in the asymmetric loading of the rotor and partially due to differing closed-loop dynamics, and they will be the subject of future investigations.

17 WIND ENERGY↗
DOE OSTI2022

100 Gb/s High Throughput Serial Protocol (HTSP) for data acquisition systems with interleaved streaming

Demands on Field-Programmable Gate Array (FPGA) data transport have been increasing over the years as frame sizes and refresh rates increase. As the bandwidths requirements increase the ability to implement data transport protocol layers using "soft" programmable logic becomes harder and start to require harden IP blocks implementation. To reduce the number of physical links and interconnects, it is common for data acquisition systems to require interleaving of streams on the same link (e.g. streaming data and streaming register access). Further, this paper presents a way to leverage existing FPGA harden IP blocks to achieve a robust, low latency 100 Gb/s point-to-point link with minimal programmable logic overhead geared towards the needs of data acquisition systems with interleaved streaming requirements.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

The Promise of Emergent Nanobiotechnologies for In Vivo Applications and Implications for Safety and Security

Nanotechnology, the multi-disciplinary field based on the exploitation of the unique physicochemical properties of nanoparticles (NPs) and nanoscale materials, has opened a new realm of possibilities for biological research and biomedical applications. The development and deployment of mRNA-NP vaccines for COVID-19, for example, may revolutionize vaccines and therapeutics. However, regulatory and ethical frameworks that protect the health and safety of the global community and environment are lagging, particularly for nanotechnology geared towards biological applications (i.e., bio-nanotechnology). Considering this, the following review, while not comprehensive, attempts to illustrate the breadth and promise of bionanotechnology developments, and how they may present future safety and security challenges. Specifically, we address current advancements to streamline the development of engineered NPs for in vivo applications and provide discussion on nano-bio interactions, NP in vivo delivery, nano-enhancement of human performance, nanomedicine, and the impacts of NPs on human health and the environment.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Dark Energy Survey Year 3 results: cosmology with moments of weak lensing mass maps – validation on simulations

ABSTRACT We present a simulated cosmology analysis using the second and third moments of the weak lensing mass (convergence) maps. The second moment, or variances, of the convergence as a function of smoothing scale contains information similar to standard shear two-point statistics. The third moment, or the skewness, contains additional non-Gaussian information. The analysis is geared towards the third year (Y3) data from the Dark Energy Survey (DES), but the methodology can be applied to other weak lensing data sets. We present the formalism for obtaining the convergence maps from the measured shear and for obtaining the second and third moments of these maps given partial sky coverage. We estimate the covariance matrix from a large suite of numerical simulations. We test our pipeline through a simulated likelihood analyses varying 5 cosmological parameters and 10 nuisance parameters and identify the scales where systematic or modelling uncertainties are not expected to affect the cosmological analysis. Our simulated likelihood analysis shows that the combination of second and third moments provides a 1.5 per cent constraint on S8 ≡ σ8(Ωm/0.3)0.5 for DES Year 3 data. This is 20 per cent better than an analysis using a simulated DES Y3 shear two-point statistics, owing to the non-Gaussian information captured by the inclusion of higher order statistics. This paper validates our methodology for constraining cosmology with DES Year 3 data, which will be presented in a subsequent paper.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Joint inference of multiplicative and additive systematics in galaxy density fluctuations and clustering measurements

Galaxy clustering measurements are a key probe of the matter density field in the Universe. With the era of precision cosmology upon us, surveys rely on precise measurements of the clustering signal for meaningful cosmological analysis. However, the presence of systematic contaminants can bias the observed galaxy number density, and thereby bias the galaxy two-point statistics. As the statistical uncertainties get smaller, correcting for these systematic contaminants becomes increasingly important for unbiased cosmological analysis. We present and validate a new method for understanding and mitigating both additive and multiplicative systematics in galaxy clustering measurements (two-point function) by joint inference of contaminants in the galaxy overdensity field (one-point function) using a maximum-likelihood estimator (MLE). We test this methodology with Kilo-Degree Survey-like mock galaxy catalogues and synthetic systematic template maps. We estimate the cosmological impact of such mitigation by quantifying uncertainties and possible biases in the inferred relationship between the observed and the true galaxy clustering signal. Our method robustly corrects the clustering signal to the sub-percent level and reduces numerous additive and multiplicative systematics from 1.5σ to less than 0.1σ for the scenarios we tested. In addition, we provide an empirical approach to identifying the functional form (additive, multiplicative, or other) by which specific systematics contaminate the galaxy number density. Even though this approach is tested and geared towards systematics contaminating the galaxy number density, the methods can be extended to systematics mitigation for other two-point correlation measurements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Dark-Matter–Electron Detectors for Dark-Matter–Nucleon Interactions

In a seminal paper now a decade old, it was shown that dark-matter detectors geared at probing interactions with nucleons could also be used to probe dark-matter interactions with electrons. In this Letter, we show that new detector concepts designed to probe dark-matter-electron interactions at low masses can similarly be used to probe new parameter space for dark-matter-nucleon interactions. We demonstrate the power of this approach by using existing data from superconducting detectors to place new limits on the interactions of nuclei with MeV-scale dark matter. Further, we show that advances in detector technology that have been anticipated for electronic interactions will automatically extend sensitivity deep into uncharted territory for nuclear interactions. This doubles the effective science output of future low-threshold experiments.

Griffin, Sinéad M↗
DOE OSTI2021

Facile ab initio approach for self-localized polarons from canonical transformations

Electronic states in a crystal can localize due to strong electron-phonon (e-ph) interactions, forming so-called small polarons. Methods to predict the formation and energetics of small polarons are either computationally costly or not geared toward quantitative predictions. Here we show a formalism based on canonical transformations to compute the polaron formation energy and wave function using ab initio e-ph interactions. Comparison of the calculated polaron and band-edge energies allows us to determine whether charge carriers in a material favor a localized small polaron over a delocalized Bloch state. Due to its low computational cost, our approach enables efficient studies of the formation and energetics of small polarons, as we demonstrate by investigating electron and hole polaron formation in alkali halides and metal oxides and peroxides. We outline refinements of our scheme and extensions to compute transport in the polaron hopping regime.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mixture Model Framework for Traumatic Brain Injury Prognosis Using Heterogeneous Clinical and Outcome Data

Prognoses of Traumatic Brain Injury (TBI) outcomes are neither easily nor accurately determined from clinical indicators. This is due in part to the heterogeneity of damage inflicted to the brain, ultimately resulting in diverse and complex outcomes. Using a data-driven approach on many distinct data elements may be necessary to describe this large set of outcomes and thereby robustly depict the nuanced differences among TBI patients’ recovery. In this work, we develop a method for modeling large heterogeneous data types relevant to TBI. Our approach is geared toward the probabilistic representation of mixed continuous and discrete variables with missing values. The model is trained on a dataset encompassing a variety of data types, including demographics, blood-based biomarkers, and imaging findings. In addition, it includes a set of clinical outcome assessments at 3, 6, and 12 months post-injury. The model is used to stratify patients into distinct groups in an unsupervised learning setting. We use the model to infer outcomes using input data, and show that the collection of input data reduces uncertainty of outcomes over a baseline approach. In addition, we quantify the performance of a likelihood scoring technique that can be used to self-evaluate the extrapolation risk of prognosis on unseen patients.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Solving Eco-Driving Problems Using Indirect Collocation Method and Smooth Representation

Here, we discuss the eco-driving problem, considering both electric and conventional powertrains, and presents a pathway to solving it numerically using an indirect collocation method. Despite the low-order system dynamics, the piecewise fuel/efficiency map, gear shifting, and real-world traffic/road situations bring system discontinuities/switchings and pure state constraints into the problem formulation, which make the problem highly nonlinear and nontrivial to solve. This letter introduces smooth approximations to convert the original problem to an unconstrained (and penalized) smooth boundary-value problem. This approach eliminates the discussion of the switching structure and leads to a lightweight Newton-method-based solution procedure.

42 ENGINEERING↗
DOE OSTI2020

Circuit Modelling of the Mechanical-Motion-Rectifier for Electrical Simulation of Ocean Wave Power Take-off

As is the case with several other mechanical power takeoffs (PTOs), the mechanical-motion-rectifier (MMR) based PTO consists of components such as one-way clutches, gears, a ball screw, mechanical couplings, and a generator. Equivalent circuit models have been created in this paper to describe the dry frictions, viscous damping, and mechanical compliances in these components, so the non-ideal efficiency and nonlinear force of the PTO can be predicted in electrical simulations by integrating these sub-circuit models. The circuit model is simplified, and its parameters are categorized as dc and ac unknowns. The dc and ac tests on the PTO are performed sequentially to extract two sets of parameters through linear regression or nonlinear curve fitting. Then, the model is validated through its prediction capability over 25 test conditions on input forces, output voltages, and efficiencies, with correlation coefficients of 0.9, 0.98, and 0.981, respectively.

42 ENGINEERING↗
DOE OSTI2023

Joint Optimization for Transport and Bucket Loading Phases of Automated Wheel Loaders

This article investigates optimization of fuel-efficiency and productivity for automated wheel loaders. A control-oriented model for both the transport phase and bucket loading phase is proposed. Here, the vehicle model includes an automatic gear shift schedule that can be incorporated into the optimization problem. Based on the model, the multistage optimization problem is formulated to simultaneously consider all phases of a short cycle with physical constraints. Cycle time and fuel efficiency are used as the weighted performance indexes in a multiobjective cost function. Bucket fill factor is included as a constraint during the bucket loading phase. A nonlinear programming problem is created with collocation using MATLAB and CasADi. The optimization solver IPOPT solves the problem to obtain the optimal state and control trajectories, which can be used as a reference for automated wheel loaders or even as a driver advisory for human-driven wheel loaders.

42 ENGINEERING↗
DOE OSTI2022

Mild hybridisation of turboprop engine with high-power-density integrated electric drives

Here this paper shares with the aerospace community a case study of turboprop mild hybridisation using a recently developed integrated drive system in the University of Nottingham, UK, within the ACHIEVE project under EU H2020 CleanSky 2 program (project No. 737814). The developed drive system enables green taxiing of a turboprop aircraft while on the ground with its engine off, and as an electrical generator when the turboprop is in the air. The entire system is designed to be able to integrate within the power auxiliary gear box (PAGB) of a turboprop aircraft. Some of the key features of the developed system include a high-speed permanent magnet machine (up to 14,200rpm) with dual three-phase design, SiC-based high power density (11.8kW/L for the power converter, 35.3kW/L and 7.2kW/kg for the machine active parts), integrated cooling design for high-temperature operation (>130°C ambient temperature), fault tolerance consideration with dual channel operation capabilities and sensorless control for entire operational conditions. This paper is giving an overview of the design process of the electrical machine, power converters, and its cooling of the entire drive. Numerical analysis (FEM and CFD) and some experimental results are presented to demonstrate the effectiveness and the desired performance of the developed integrated drive system.

42 ENGINEERING↗
DOE OSTI2025

A molecular conveyor belt-associated protein controls the rotational direction of the bacterial type 9 secretion system

ABSTRACT Many bacteria utilize the type 9 secretion system (T9SS) for gliding motility, surface colonization, and pathogenesis. This dual-function motor supports both gliding motility and protein secretion, where rotation of the T9SS plays a central role. Fueled by the energy of the stored proton motive force and transmitted through the torque of membrane-anchored stator units, the rotary T9SS propels an adhesin-coated conveyor belt along the bacterial outer membrane like a molecular snowmobile, thereby enabling gliding motion. However, the mechanisms controlling the rotational direction and gliding motility of T9SS remain elusive. Shedding light on this mechanism, we find that in the gliding bacteriumFlavobacterium johnsoniae, deletion of the C-terminus of the conveyor belt-associated protein GldJ controls and, in fact, reverses the rotational direction of T9SS from counterclockwise (CCW) to clockwise (CW). This suggests that the interface between the conveyor belt-associated protein GldJ and the T9SS ring protein GldK plays an important role in controlling the directionality of T9SS, potentially by modulating its interaction with the stator complex GldLM, which drives motor rotation. Combined with MD simulation of the T9SS stator units GldLM, we suggest a “tri-component gearset” model where GldJ controls the rotational direction of its driver, the T9SS, thus providing adaptive sensory feedback to influence the motility of the gliding bacterium. IMPORTANCE The type 9 secretion system (T9SS) is fundamental to bacterial gliding motility, pathogenesis, and surface colonization. Our findings reveal that the C-terminal region of the conveyor belt-associated protein GldJ functions as a molecular switch which is capable of reversing the rotational direction of T9SS. Through the coordinated actions of the T9SS stator units (akin to a driving motor), the GldK ring (the gear that converts rotational energy into linear movement), and GldJ, this machinery forms a smart conveyor belt system reminiscent of flexible or cognitive mechanical conveyors. Such advanced conveyors can alter their direction to adapt to shifting demands. Here, we show that the bacterial T9SS similarly adjusts its rotational bias based on feedback from the conveyor belt-associated protein GldJ. This dual-role feedback mechanism underscores an evolved, controllable biological snowmobile, offering new avenues for studying how bacteria fine-tune motility in dynamic environments.

Microbiology↗
DOE OSTI2026

Nutrient limitation shapes functional traits of mycorrhizal fungi and phosphorus-cycling bacteria across an elevation gradient

In nutrient-limited high-elevation ecosystems, plants rely on arbuscular mycorrhizal (AM) fungi to provide mineral phosphorus (P) in the form of phosphate (PO43-). AM fungi gather these nutrients from phosphorus-cycling bacteria (PCBs) that can mineralize PO43- from organic matter and solubilize mineral-bound P. How climate, soil factors, and nutrient limitation influence AM fungi and PCB assembly remains unclear. We collected soil from montane meadows across a 1,000-m elevation gradient on three replicate mountainsides and analyzed AM fungal marker genes, P-cycling genes from shotgun metagenomes, and edaphic measurements. High-elevation soils had nearly 50-fold less soil PO₄³⁻ and 60% more AM fungal hyphae than low-elevation soils. AM fungal turnover was linked to changes in pH, organic carbon, and PO₄³-. The composition of 198 P-cycling genes was influenced by the AM fungal community structure. Drivers of individual PCB functional genes, including pH and organic carbon, varied with gene phylogeny. We found a trade-off in P-cycling strategies across elevation: P-rich, low-elevation soils supported root-colonizing AM fungi and organic P-mineralizing bacteria. P-poor, high-elevation soils were dominated by stress-tolerant AM fungi and mineral P-solubilizing bacteria. Our results suggest that AM fungi and PCB community turnover across elevation are both shaped by pH, organic carbon, and P availability. With continued climate warming, the structure and function of mountaintop ecosystems might shift to resemble lower elevations, disrupting long-established and specialized microbial assemblages, with consequences for P-cycling dynamics and the total P available to plant communities.IMPORTANCEPhosphorus (P) limits plant productivity in high-elevation ecosystems, yet the microbial networks that mobilize P, including arbuscular mycorrhizal (AM) fungi and phosphorus-cycling bacteria (PCBs), remain under-characterized in these nutrient-poor soils. We show that across a 10,00-m elevation gradient, AM fungi and P-cycling gene assemblages shift predictably with pH, organic carbon, and phosphate availability. Higher elevations, with less available P, select for stress-tolerant AM fungal taxa and PCB strategies geared toward mineral solubilization, while low-elevation sites favor root colonization by AM fungi and organic P mineralization. These results suggest that nutrient limitation can constrain microbial community assembly in consistent ways across landscapes. High mountain soils are low in P and rely on a network of underground AM fungi and PCB to deliver nutrients to plants. This study shows how those underground relationships reorganize with elevation and how climate change could collapse long-standing microbial strategies by pushing high-elevation ecosystems toward lowland conditions. As soils warm and dry, the microbial scaffolding that supports alpine plant life may become increasingly unstable.

arbuscular mycorrhizal fungi↗
DOE OSTI2023

HopPyBar

HopPyBar is a python program to import, analyze, and export split-Hopkinson pressure bar (SHPB, also known as Kolsky bar) data. Traditional analysis offers a black box approach, where input data is converted to analyzed output by performing a series of calculations without user involvement. This program serves as a developmental platform to "white box" the data analysis process. Data streams can be captured (in-situ) to enable advanced or unconventional analyses, statistics, and comparisons. Additionally, the program is geared towards the standardized forms of input and output used at LANL to streamline analysis, but the open nature of the program makes additional input/output schemes straightforward to add. General workflow will import SHPB data in one of a number of formats, identify relevant portions of data signals, and convert to stress-strain-strain rate to show material behavior as a function of dynamic testing.

Morrow, Benjamin↗
DOE OSTI2023

ResStock™ v3.2.0 [SWR-19-15 and SWR-20-07]

The ResStock™ analysis tool was built on NREL's OpenStudio® platform, and is a project geared at modeling existing residential building stocks at national, regional, or local scales with a high-degree of granularity (e.g., one physics-based simulation model for every 200 dwelling units), using the EnergyPlus® simulation engine. Information about ComStock™, a sister tool for modeling the commercial building stock, can be found here: https://www.nrel.gov/buildings/comstock.html This repository contains: Housing characteristics of the U.S. residential building stock, in the form of conditional probability distributions stored as tab-separated value (.tsv) files. Comments at the bottom of each file document data sources and assumptions for each. A library of housing characteristic "options" that translate high-level characteristic parameters into arguments for OpenStudio measures, and which are referenced by the housing characteristic .tsv files and building energy upgrades defined in project definition files Project definition files: v2.3.0 and later: buildstockbatch YML files openable in any text editor v2.2.5 and prior: Project folder openable in PAT Unit-level OpenStudio Measures for automatically constructing OpenStudio Models of each representative dwelling unit model: v3.0.0 and later: OpenStudio-HPXML Measures v2.5.0 and prior: OpenStudio Measures Higher-level OpenStudio Measures for controlling simulation inputs and outputs This repository does not contain software for running ResStock simulations, which can be found as follows: Versions 2.3.0 and later only support the use of buildstockbatch for deploying simulations on high-performance or cloud computing. Version 2.3.0 also removed separate projects for single-family detached and multifamily buildings, in lieu of a combined project_national representing the U.S. residential building stock. See the changelog for more details. Versions 2.2.5 and prior support the use of the publicly available OpenStudio-PAT software as an interface for deploying simulations on cloud computing. Read the documentation for v2.2.5.

Horowitz, Scott↗
DOE OSTI2024

Toward improved thermal exposure classes for structural firefighters

In the early 1970s, there was an initial effort to quantify the conditions under which firefighters are expected to perform. Harvey Utech led this endeavor by defining three levels of thermal exposure—routine, ordinary, and emergency—which were characterized by combining a range of air temperatures and radiative heat fluxes. In the last half-century, there has been a concerted scientific effort to further understand the conditions to which firefighters are exposed during structural firefighting. Research has been conducted on the resiliency of turnout gear and facepiece lenses, the thermal conditions observed during a structure fire, and the impact of firefighter tactics such as ventilation and suppression. The authors synthesize the results from these research areas to update the original thermal classifications to six categories of exposure—routine, Ordinary I, Ordinary II, Emergency I, Emergency II, and Emergency III—which are more representative of the operating environment and protective equipment thresholds that firefighters should be aware of during firefighting operations and tactical decision-making.

Weinschenk, Craig↗
DOE OSTI2023

Experimental Verification of An Electro-Hydraulic Actuation System Driven by An Integrated Electro-Hydraulic Unit

This paper proposes an electro-hydraulic actuator (EHA) system, and a novel-designed electro-hydraulic unit (EHU) consisting of a fixed-displacement hydraulic gear machine and a variable-speed electric machine. The novel EHU design integrates an electric machine and a hydraulic machine in a single housing, targeting optimal compactness, power density, and component reduction. The EHA system features an open circuit design, where hydraulic hoses connect the EHU with a tank, a valve manifold, and the hydraulic cylinder. In this way, the proposed EHA technology can be used to implement distributed hydraulic actuation in a vehicle without requiring changes to the hydraulic actuators or at the overall layout of the hydraulic components with respect to the original vehicle design. A dedicated test rig is developed to verify the performance of the proposed EHA system. Here, the efficiency of the EHA is measured in a steady state and under a realistic duty cycle of a commercial compact loader. The efficiency of the EHA system based on the measurements on the test rig can reach 54% with up to 20 kN load and 6 kW power level. Furthermore, the EHU is implemented on the reference machine to drive the boom function. Preliminary results on the performance of the EHU show an efficiency of up to 68% under different loading conditions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗