Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “filler”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Anisotropic Thermally Conductive Composites Enabled by Acoustophoresis and Stereolithography

Opportunities to improve thermal management in electronic devices are currently hindered by processing constraints that limit thermal conductivity in polymer-matrix composites. Active patterning of filler particles is a promising route to improve conductivity while retaining processability by improving particle contact density and directing heat along optimized pathways. Here, we employ acoustic patterning to align and compact filler particles into stripes during stereolithographic 3D printing. This approach produces polymer-based composite materials with highly efficient embedded heat transport pathways which reach 95 vol% particle utilization (relative to the parallel conduction upper limit). These composites exhibit anisotropic thermal conductivity up to 300% higher than unpatterned composites, with in-plane anisotropy ratios of up to 350%. Combining this high conductivity with 3D printing enables materials with engineered heat networks that optimize transport from hot spots to heatsinks while maintaining low viscosity for fast particle patterning and for infiltration around electronic components. Finally, numerical simulations of acoustic assembly of particles with varied geometry, when compared to experimentally characterized particle packing, illuminate pathways for further improving conductivity by optimizing particle geometry for alignment and stacking of particles with maximum contact surface area.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Conductive Ink with Circular Life Cycle for Printed Electronics

Electronic waste carries energetic costs and an environmental burden rivaling that of plastic waste due to the rarity and toxicity of the heavy-metal components. Recyclable conductive composites are introduced for printed circuits formulated with polycaprolactone (PCL), conductive fillers, and enzyme/protectant nanoclusters. Circuits can be printed with flexibility (breaking strain ≈80%) and conductivity (≈2.1 × 10 4 S m -1 ). These composites are degraded at the end of life by immersion in warm water with programmable latency. Approximately 94% of the functional fillers can be recycled and reused with similar device performance. The printed circuits remain functional and degradable after shelf storage for at least 7 months at room temperature and one month of continuous operation under electrical voltage. Here, the present studies provide composite design toward recyclable and easily disposable printed electronics for applications such as wearable electronics, biosensors, and soft robotics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Molecular Interlocking Multidimensional Modulations of Cathode‐Electrolyte Interface for Constructing High Energy Density Quasi‐Solid‐State Batteries

Gel polymers are regarded as a promising candidate electrolyte for lithium-metal quasi-solid-state batteries, primarily due to their high ionic conductivity and solid-liquid synergistic properties. However, challenges such as interfacial side reactions, limitations in Li + transport caused by interfacial issues, and leaching of transition metals from the cathode have yet to be effectively solved. Herein, a novel gel electrolyte modulation strategy based on electrostatic filler assembly is proposed to address the issues of ineffective capacity utilization and inadequate cycling stability of high-energy-density cathode materials in solid-state lithium-ion batteries. It constructs a 3D interpenetrating charge-bridge network that effectively tackles the phase-separation challenge between fillers and electrolytes at the molecular level. Meanwhile, the molecular interlocking structure effectively inhibits the electrolyte erosion. More critically, it optimizes and stabilizes the cathode-electrolyte interface film, which facilitates the conduction of Li + -ions through a size-sieving mechanism. Consequently, this strategy enables effective adaptation across diverse high-energy-density cathode materials with satisfactory capacity performance (170.4 mAh g −1 at 4.5 V/1 C for LiNi 0.6 Co 0.2 Mn 0.2 O 2 and 194.0 mAh g −1 at 4.3 V/1 C for LiNi 0.9 Co 0.08 Mn 0.02 O 2 ). In conclusion, this investigation offers a straightforward and effective reference for addressing the critical challenges of ionic transport and interface stabilization in the design of gel electrolytes.

cathode-electrolyte interface↗
DOE OSTI2020

On the Use of Surfactant-Complexed Chitosan for Toughening 3D Printed Polymethacrylate Composites

This work reports a simple approach to prepare toughened 3D-printed polymethacrylate (PMA) composites using surfactant-modified chitosan (SMCS) particles at loadings between 2–10 wt%. Chitosan (CS) is modified with anionic surfactant, sodium dodecyl sulfate, via ionic complexation to facilitate compatibility and dispersion of CS to PMA matrix by non-covalent interactions between the components. The study successfully demonstrates high-accuracy 3D printing of composites with significant improvements in the overall mechanical properties. The composite with the best loading of 8 wt% SMCS shows a tensile modulus of 1.23 ± 0.05 GPa, a tensile strength at 49.8 ± 0.96 MPa, a yield stress at 33.3 ± 1.48 MPa, and a strain-at-ailure 10.3 ± 0.61%, which are 45%, 40%, 32%, and 68% higher than neat PMA, respectively. This provides a significant improvement in toughness at 4.92 ± 0.55 MJ m -3 for the composite, 184% higher than that of neat PMA. The marked increase in toughness is due to enhanced filler-matrix interactions which improve the ability of the 3D printed composite to absorb energy under tensile load. The results from this work provide new understandings into the strategies for design and preparation of stereolithography 3D printed materials reinforced with toughening fillers from renewable resources.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Acrylonitrile-butadiene-lignin thermoplastic rubber adhesive for enhanced metal-to-metal joining

With the growing requirement for lightweight structural materials in automotive, aerospace, and infrastructure applications, multi-material joints made with adhesive have attracted intense research interest. Commercial thermoset adhesives are one-time cures, and difficult to disassemble the bonded components for repair and recycling. Our prior work with a thermoplastic acrylonitrile-butadiene-lignin rubber (ABL) addresses this sustainability/recycling challenge, but the adhesive exhibits deficient joining strength compared to standard thermosets. Here, we modify the ABL matrix by loading particulate fillers to enhance its modulus and toughness. Further, the goal is to manufacture a cure-free thermoplastic adhesive system with a simple dispensing protocol and characteristic ductility combined with a high yield stress for improved shear strength of a bonded joint. Fumed silica (FS) and epoxidized glass spheres (EGS) were used as fillers in the ABL to promote the dispersion of lignin particles that tailored the functionalities and free energy components of the adhesive surface. With optimal loading of FS (5 wt%) and EGS (30 wt%) in the ABL adhesive matrix, the lap-shear strength of the bonded aluminum joint was elevated by 128%, compared to the neat ABL, reaching 21 MPa, which is 90% of the performance of a commercial epoxy-based adhesive.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Poly(ether‐block‐amide) membrane with deformability and adjustable surface hydrophilicity for water purification

Abstract Freshwater resources are currently insufficient, and another form of freshwater resources, namely, ice, is very interesting except for the issue of how to use new materials for effective purification during the processing procedure. In this article, a new membrane material with multisize pore structure in the cross‐section and intact thin skin layer on the upper and lower surfaces was successfully prepared by adding porogen, filler and setting heating environment during the phase separation process. The membrane exhibits excellent axial deformability, and its elongation at break can reach to 160% strain. Meanwhile, they all show elastic deformation behavior in the range from −60 to 100°C. Even if high content of hydrophobic filler is compounded into these membranes, that is, 5.7 wt% carbon tube content, water contact angle of membrane's surface is only 72.5°, demonstrating obvious hydrophilicity. In addition, in the water purification process, the adsorption rate constant reached ideal value of 0.26 s −1 , and the equilibrium adsorption capacity was about 2.8 g/g, showing fast and efficient water purification ability. In the mode of external heating source or the membrane's heat dissipation, these prepared membranes can melt the ice to obtain purified water and exhibit a controllable purification ability in this process.

Ge, Chengbiao↗
DOE OSTI2024

The Effects of Material-Filled Voids on Detonation Wave Shape in Rubberized RDX Explosives

The sensitivity of explosives is affected by inhomogeneities within the material. This is evident in the increased shock sensitivity of explosives with slightly lower densities resulting from an increased number of hotspots. The influence of hotspots on explosive initiation has been well studied; however, few studies have been conducted on the effect of intermediate-sized voids (0.1–10 mm) on a propagating detonation wave. Cylindrical voids filled with air have been studied for diameters ranging from 0.3 mm to 0.8 mm for both 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX) and 1,3,5-trinitro-1,3,5-triazinane (RDX)-based rubberized explosives. Continuing the investigation into single cylindrical voids, this study examined the effects of 0.5 mm diameter voids filled with different inert cylindrical metals on the detonation wave shape for an RDX-based rubberized explosive. The metals selected for experiments were 1066 aluminum, brass, copper, and tungsten. The propagation of the detonation wave was captured using a digital streak camera. Experimental results showed that the extent of detonation wave shaping was closely tied to the density differential between the bulk explosive and metal insert. Forty-four different filler materials, including non-metals, were simulated using a hydrodynamic code to further analyze material inclusion effects. The main factors hypothesized to be of interest were bulk sound speed, shock impedance, and filler material density. We found that the local detonation delay could be correlated fairly well to a ratio of bulk sound speed and density. Understanding the influence of material inclusions on detonation performance and wave shape allows for tailoring of detonations.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2026

Particle‐Size‐Dependent Lithium‐Ion Transport in PEO/LLZO Composite Electrolytes

Lithium-metal batteries with solid electrolytes can deliver higher energy density and improved safety than conventional Li-ion batteries. Among solid electrolyte candidates, polymer/ceramic composite electrolytes are attractive because they combine polymer flexibility with the high ionic conductivity of ceramics. However, whether ceramic fillers synergistically reduce polarization losses in the polymer matrix remains unclear. A central unknown is the critical polymer/ceramic interfacial resistance (Rint,crit), below which adding ceramics lowers electrolyte overpotential. Here, we present the first macroscale model framework to quantify R int,crit for composite electrolytes based on polyethylene oxide (PEO) and Ta-doped Li 7 La 3 Zr 2 O 12 (LLZO). A 1D model for DC-polarization of tri-layer cells (PEO-LiTFSI/LLZO/PEO-LiTFSI) shows that LLZO surface functionalization reduces the PEO/LLZO interfacial resistance, consistent with electrochemical impedance measurements. Extending to a 2D composite model, we show notably that Rint,crit scales linearly with LLZO particle diameter and shifts toward experimentally accessible values (e.g., 28.8 Ωcm 2 ) as particle size increases. At fixed ceramic volume fraction, larger LLZO particles reduce the number of interfacial crossings, driving more current through the ceramic phase and lowering concentration polarization. In contrast, R int,crit is largely independent of ceramic volume fraction. These results demonstrate that ceramic filler-size engineering can enable synergistic, energy-efficient transport in polymer/ceramic composite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2025

Welding investigation of a wrought FeMnAl steel for armor application

A new wrought FeMnAl steel contains high Mn content and high Al content. This steel has high strength. When it is compared to conventional steels with the similar strength, its density is lower. FeMnAl steels can be used in armor vehicle manufacturing, in which welding is a common practice to join the steel plates together. The welding of FeMnAl steels has not been sufficiently studied before. Here, this work studied the weldability and weld microstructure of an FeMnAl steel and provided useful data for the welding practice of FeMnAl steels. The influences of weld filler metals and shielding gases were studied, using single-pass bead-on-plate gas metal arc welding (GMAW) and gas tungsten arc welding (GTAW) two processes. The optimal filler metals and shielding gases have been determined to achieve the better weldability. Autogenous GTAW and electron beam welding were also conducted. Cracks were found in the HAZ in the GMAW welds and electron beam welds. Fewer or no cracks were found in the HAZ of GTAW welds. SEM, SEM/EDX, TEM, TEM/EDX, and EBSD were used to analyze the grain boundaries in the HAZ and the cracks. The grain boundaries of FeMnAl base metal are mostly high angle grain boundaries (HAGBs), which attract impurity and solute atoms and cause intergranular cracking. The proposed cracking mechanisms are liquation cracking and ductility-dip cracking. It was found that GTAW provides much better weldability for the FeMnAl steel than GMAW and EBW.

FeMnAl steel↗
DOE OSTI2021

Mica filled polyetherketoneketones for material extrusion 3D printing

Polyetherketoneketone (PEKK) has superior physical properties to most available thermoplastics compatible with material extrusion-based 3D printing, including analogs in the polyaryletherketone (PAEK) family. To date, the performance of fused filament fabrication (FFF) compatible PEKK has been detailed primarily as a function of varying the isomer ratios composing the co-polymer structure. The strategy to form blends or composites with PEKK for FFF is attractive for further tailoring of performance in application, yet has received limited attention. Here, we report the integration of three grades of mica platelets into PEKK at 10% and 30% mass loadings to generate an array of filament feedstocks that were then used to print objects with a simple FFF machine. The effects of mica coating chemistry and surface treatment on the compatibility with PEKK and resulting properties are described. Mica fillers at both loadings have only subtle influence on the FFF relevant melt rheological properties inherent to PEKK. Pigment micas at high loadings can lower the melting temperature of PEKK (up to 19 ºC) without shifting its glass transition temperature and inhibit much of the undesirable crystallization occurring during processing with unfilled PEKK. The printed composites were effectively cold crystallized post-printing, affording crystalline fractions up to 90% relative to unfilled PEKK with increased dimensional stabilities. All micas, when used as fillers in low and high relative PEKK crystallinities, significantly increased the tensile modulus (as high as 126% or to 7.31 GPa) of parts in correlation to the loading. Furthermore, the underlying microstructural features of a printed composite were compared to unfilled PEKK by use of a high-resolution helical micro-computed tomography instrument. Practically, pigment micas can confer a wide range of rich colors to 3D-printed PEKK.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Methodology to determine printability criteria of highly concentrated pastes through rheological characterization

Material extrusion is an additive manufacturing technique that enables the creation of reproducible and complex hardware by depositing a viscous, shear-thinning ink onto a substrate in a custom-pattern via extrusion through a syringe. Here, the ability of an ink to be extruded onto a substrate in many layers, and maintain the desired shape is what defines the printability. Printability is often investigated by formulating, printing, and postmortem analysis of final parts in an iterative manner. Investigations of printability through rheological characterization have often been concerned with inks that straddle the line between printable and too thin, leaving out an entire class of inks that are highly-filled pastes, where extrudability is the limiting factor. Highly-filled pastes continue to pose issues for researchers as the effect of filler morphology, size, loading, and packing fraction on the ink rheology and corresponding printability is not understood. While traditional rheological characterizations may be useful for some inks, we show that protocols utilizing steady-shear, or large-amplitude oscillatory shear are difficult and unreliable for highly-filled pastes. Through transient rheology paired with real-time images we show that each traditional protocol produces inhomogeneous deformations that violate the assumptions that underly common rheological definitions. Instead, we demonstrate metrics measured with small-amplitude oscillatory shear that are correlated to the printability of various ink formulations ranging in loading. The rheological measures that accurately predict the printability of the inks are the axial stress measured at small amplitudes, and the critical stress amplitude above which rheological characterizations become impossible. In addition, we estimate the maximum packing fraction for each filler, based on the exponent common to hard sphere models, and show that the printability of each ink can be predicted by the ratio of the packing fraction to the theoretical maximum. We show how small-amplitude oscillatory shear allows users to develop printability criteria for any ink to enhance the workflow in the development of new inks, increase the performance of material extrusion printing, and improve the stability of printed parts, with less wasted time and materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Three influential factors on colloidal nanoparticle deposition for heat conduction enhancement in 3D chip stacks

Thermal management is one of the major challenges facing the development of three-dimensional (3D) chip stacks. Recently, experimental studies have shown that neck-based thermal structure (NTS) between chip layers formed by drying of colloidal suspension in cavity filled with micro-size particles can improve the vertical heat conduction threefold. However, a deep understanding of the mechanisms of neck formation and its influence on heat conduction is still lacking. In this paper, we numerically study the effects of three parameters, i.e., initial nanoparticle concentration, drying temperature and chip surface wettability on neck formation between filler particles and on the resulting heat conduction of the NTS. With increasing nanoparticle concentration, the size and number of necks increase, resulting in an increased effective thermal conductivity (ETC) of NTS. The drying temperature is found to have only little influence on the ETC of resultant NTS, while the neck size and spatial distribution become more uniform at higher drying temperature. When reducing the wettability of the top and bottom surfaces of the cavity, the necks shrink in size until completing evacuating at the top and bottom layers, while the size of the necks between filler particles in the middle height of the cavity expands slowly. In consequence, the ETC of NTS drops at an increasing rate. Being able to reveal the underlying multiple mechanisms of two-phase flow, phase change and heat transport, the current numerical study suggests optimal values for the deposition process, with initial nanoparticle concentration over 0.8%, a drying temperature of 60°C and a uniform contact angle of 30° for practical production of NTS.

3D chip stacks↗
DOE OSTI2020

Surface-modified and oven-dried microfibrillated cellulose reinforced biocomposites: Cellulose network enabled high performance

Microfibrillated cellulose (MFC) is widely used as a reinforcement filler for biocomposites due to its unique properties. However, the challenge of drying MFC and the incompatibility between nanocellulose and polymer matrix still limits the mechanical performance of MFC-reinforced biocomposites. In this study, we used a water-based transesterification reaction to functionalize MFC and explored the capability of oven-dried MFC as a reinforcement filler for polylactic acid (PLA). Remarkably, this oven-dried, vinyl laurate–modified MFC improved the tensile strength by 38 % and Young’s modulus by 71 % compared with neat PLA. Our results suggested improved compatibility and dispersion of the fibrils in PLA after modification. This study demonstrated that scalable water-based surface modification and subsequent straightforward oven drying could be a facile method for effectively drying cellulose nanomaterials. We find that the method helps significantly disperse fibrils in polymers and enhances the mechanical properties of microfibrillar cellulose-reinforced biocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Enhancing thermal conductivity and toughness of cellulose nanofibril/boron nitride nanosheet composites

Generally, the thermal conductivity (TC) of composite based on cellulose nanofibrils (CNF) is improved by adding thermal conductive filler, which inevitably leads to the loss of its mechanical properties. Here, in this work, it is the first to simultaneously improve the toughness and TC of CNF/boron nitride nanosheets (BNNS) composite from the perspective of thermal conductive filler addition and CNF crystal change. The hydrophilic-modified BNNSs were successfully prepared by xylose-assisted ball-milling prior to adding into CNF. Compared with that of CNF film (1.34 W/(m·K)), the in-plane TC of CNF/BNNS composite (12.68 W/(m·K)) increased significantly by 846 % with loading 30 % BNNS. Afterwards, both toughness (8.0 MJ·m -3 , increased ~250 %) and TC (14.7 W/(m·K), increased ~16 %) of CNF/BNNS composite were further enhanced significantly by mercerization with 12.5 % NaOH solution. The simultaneously improvement of toughness and TC is unprecedented in related studies, which contributes to the effective preparation of thermal management materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Bio-treatment of poplar via amino acid for interface control in biocomposites

Advanced biocomposites reinforced by abundant biomass-derived fillers can add a revenue stream to enhance the economic viability of biofuel production chains and the energy efficiency of the composite industry. However, the low stiffness of biopolymers limits their use in structural applications. Poplar fibers (mesh size: <180 μm, Populus spp.), an abundant waste from the wood industry, were used as bio-filler to fabricate high-performance biocomposites based on polylactic acid (PLA), in which the poplar fibers were modified by an amino acid (l-lysine). As a benefit of the amino acid treatment, the tensile Young's moduli of the lysine/poplar/PLA composites increased by up to 68% with the addition of a small amount of lysine, compared with neat PLA. At the same time, the tensile strength, failure strain, and Young's modulus of the poplar/PLA composites all increased after adding only 0.1 wt % of lysine. It has been observed that the lysine content has a significant effect on the decomposition temperature, complex viscosity, storage modulus, crystallization temperature, and crystallinity of composites. The fracture surfaces of the composites with an optimum lysine content had fewer voids and were more compact compared with composites without any lysine. The pores on the surfaces of poplar fibers became more available for the penetration of PLA molecules as a result of lysine addition. Finally, this study presents a facile method for reinforcing biocomposites with extremely low-cost and environmentally friendly biofillers.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Achieving extraordinary thermal stability of salt hydrate eutectic composites by amending crystallization behaviour with thickener

Commercial thermal energy storage (TES) systems necessitate reliable thermal performance throughout their operational lifetime. Repeated volume changes of the phase change materials (PCMs) during thermal cycling disengages thermal contacts between the conductive fillers like expanded graphite (EG) in TES composites, causing unstable thermal conductivity (k) that fades with cycling. Our in-operando crystallization studies on eutectic PCM made of zinc nitrate hexahydrate (ZNH) and KNO 3 revealed that the thermal stability of PCM composites can be considerably degraded by the formation of large and sharp-cornered PCM crystals during the freezing cycle. While the crystals can push EG particles, disengaging thermal contacts between them, we have newly discovered that carboxymethyl cellulose (CMC) can be used to retain the thermal contacts by forming networks of smaller PCM crystals. Furthermore, the scalable synthesis methodology of EG/ZNH eutectic composites was introduced. Here, in this study, EG particles were strongly connected into a matrix via a stable, corrosion resistant polydimethylsiloxane (PDMS) binder, stabilizing thermal networks and thereby maintaining k up to 1000 melt/freeze cycles. The thermal conductivity of our 25 vol% EG sample (13.3 W m -1 K -1 ) is more than 48% higher than other salt hydrate eutectic composites reported in the literature. We expect this study to provide insights on cooperative interaction between different components of TES systems (PCM, filler, thickener, binder) for exceptionally robust thermal properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of 3D printed lightweight hybrid composites via theoretical modeling and machine learning

Hybrid composites combine two or more different fillers to achieve multifunctional or advanced material properties, such as lightweight and enhanced mechanical properties. The properties of the composites significantly depend on their microstructures, which can be tailored via advanced 3D printing processes. Understanding the process-structure-property relationships is critical to enable the design and engineering of novel hybrid composites for applications in aerospace, automotive, and protective coatings. Here, for this work, we develop 3D printable and lightweight hybrid composites and leverage the conventional design of experiments, a theoretical hybrid model, and an image-driven machine learning (ML) method to investigate their mechanical behaviors. The hybrid composites are formulated with elastomer matrix, microfillers, and thin-shell particles, enabling a significant degree of design freedom of microstructures with densities and mechanical properties varying up to 70% and 91%, respectively. Our statistical analysis indicates that the 3D printing path direction and the microfibers fraction are dominating process parameters with contribution percentages of 45.3% and 57.7% on the specific stiffness and strength, respectively. A hybrid mechanics model is developed based on a simple Weibull distribution function and classical single-filler models to effectively capture the variations in mechanical properties, however, it overestimates the values due to its statistical constraints and idealization of experimental uncertainty. The image-driven ML model leverages the microscale images directly without losing the structural details, shows more accurate predictions with experimental data, and has 48.6% lower root mean square error than the theoretical model.

3D printing↗
DOE OSTI2025

Corrosion resistant hot melt adhesive to bind metals

Hot melt adhesives (HMAs) play an important role in many industries, and their demand is expected to grow. HMAs don't require any solvents, and their application results in the formation of strong bonds with the substrate upon cooling within seconds. These properties differentiate them from liquid glues and make them preferable for practical application. Currently, commercial HMAs are used in bonding lightweight materials such as paper, polymers, and cartons, and have limited usage in areas necessitating the bonding of heavier objects like metals. Here, in this study, we report a design and testing of versatile platform comprising an ion-coordinating polymer and ionic fillers for performance optimization and understanding of structure–property relationships, enabling the rational design of HMAs with improved adhesion to metal surfaces. All-atom Molecular dynamics (MD) simulations and various characterization methods are used to elucidate the adhesion mechanism in model composite system containing polyethylene oxide mixed with chemically diverse salt particles. The maximum adhesion strength is found in composites with Al(OH) 3 and FeCl 3 fillers. Interestingly, the presence of Al(OH) 3 also provides a multifunctional anticorrosion property as measured electrochemically using the Tafel method. The discovered path to formulations with improved adhesion to metal surfaces constitutes an important step toward advancing HMAs for use in the structural and semi-structural metal work domain.

Adhesive and cohesive forces↗