Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “field enhancement factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Dose rate, dose-equivalent rate, and quality factor in SLS-1

A tissue-equivalent proportional counter (TEPC) sensitive to the lineal energy range of 0.26-300 keV micrometer-1 was flown on STS-40 (39 degrees x 278 km x 296 km) inside the Spacelab. This instrument was previously flown on STS-31 but was modified to provide a finer resolution at lower lineal energies to better map the South Atlantic Anomaly (SAA) protons. The instrument was turned on 6 June 1991, and operated for 7470 min (124.5 h). The flight duration was characterized by a very large number of X-ray solar flares and enhanced magnetic field fluctuations; however, no significant dose from the solar particles was measured at the location of this instrument. The flight data can be separated into trapped and galactic cosmic radiation parts. The dose rate, dose-equivalent rate and quality factor for trapped radiation were 4.21 +/- 0.03 mrad day-1, 7.72 +/- 0.05 mrem day-1, and 1.83 +/- 0.1, respectively. The dose rate, dose-equivalent rate, and quality factor for galactic cosmic radiation were 5.34 +/- 0.03 mrad day-1, 14.63 +/- 0.06 mrem day-1, and 2.74 +/- 0.1, respectively. The overall quality factor for the flight was 2.38. The dose from the GCR is higher than from SAA protons because of the high inclination and low altitude of this flight. The AP8MAX model of the trapped radiation gives a dose rate of 2.43 mrad day-1 and a quality factor of 1.77. The CREME solar maximum model of galactic cosmic radiation gives a dose rate of 2.54 mrad day-1 and a quality factor of 2.91. Thus the AP8MAX model underestimates the dose by a factor of 1.8 whereas the CREME model leads to an underestimation of the dose by a factor of 2. A comparison of the LET spectra using the AP8MAX model and galactic cosmic radiation transport codes shows only a qualitative agreement.

NASA Discipline Number 00-00↗
NASA NTRS1996

Experimental Investigation of Pool Boiling Heat Transfer Enhancement in Microgravity in the Presence of Electric Fields

Boiling is an effective mode of heat transfer since high heat flux levels are possible driven by relatively small temperature differences. The high heat transfer coefficients associated with boiling have made the use of these processes increasingly attractive to aerospace engineering. Applications of this type include compact evaporators in the thermal control of aircraft avionics and spacecraft environments, heat pipes, and use of boiling to cool electronic equipment. In spite of its efficiency, cooling based on liquid-vapor phase change processes has not yet found wide application in aerospace engineering due to specific problems associated with the low gravity environment. After a heated surface has reached the superheat required for the initiation of nucleate boiling, bubbles will start forming at nucleation sites along the solid interface by evaporation of the liquid. Bubbles in contact with the wall will continue growing by this mechanism until they detach. In terrestrial conditions, bubble detachment is determined by the competition between body forces (e.g. buoyancy) and surface tension forces that act to anchor the bubble along the three phase contact line. For a given body force potential and a balance of tensions along the three phase contact line, bubbles must reach a critical size before the body force can cause them to detach from the wall. In a low gravity environment the critical bubble size for detachment is much larger than under terrestrial conditions, since buoyancy is a less effective means of bubble removal. Active techniques of heat transfer enhancement in single phase and phase change processes by utilizing electric fields have been the subject of intensive research during recent years. The field of electrohydrodynamics (EHD) deals with the interactions between electric fields, flow fields and temperature fields. Previous studies indicate that in terrestrial applications nucleate boiling heat transfer can be increased by a factor of 50 as compared to values obtained for the same system without electric fields. Imposing an external electric field holds the promise to improve pool boiling heat transfer in low gravity, since a phase separation force other than gravity is introduced. The goal of our research is to experimentally investigate the potential of EHD and the mechanisms responsible for EHD heat transfer enhancement in boiling in low gravity conditions.

Herman, Cila↗
NASA NTRS2009

Enhancing SERS by Means of Supramolecular Charge Transfer

In a proposed method of sensing small quantities of molecules of interest, surface enhanced Raman scattering (SERS) spectroscopy would be further enhanced by means of intermolecular or supramolecular charge transfer. There is a very large potential market for sensors based on this method for rapid detection of chemical and biological hazards. In SERS, the Raman signals (vibrational spectra) of target molecules become enhanced by factors of the order of 108 when those molecules are in the vicinities of nanostructured substrate surfaces that have been engineered to have plasmon resonances that enhance local electric fields. SERS, as reported in several prior NASA Tech Briefs articles and elsewhere, has remained a research tool and has not yet been developed into a practical technique for sensing of target molecules: this is because the short range (5 to 20 nm) of the field enhancement necessitates engineering of receptor molecules to attract target molecules to the nanostructured substrate surfaces and to enable reliable identification of the target molecules in the presence of interferants. Intermolecular charge-transfer complexes have been used in fluorescence-, photoluminescence-, and electrochemistry-based techniques for sensing target molecules, but, until now, have not been considered for use in SERS-based sensing. The basic idea of the proposed method is to engineer receptor molecules that would be attached to nanostructured SERS substrates and that would interact with the target molecules to form receptor-target supramolecular charge-transfer complexes wherein the charge transfer could be photoexcited.

Wong, Eric↗
NASA NTRS2014

Plasma Distribution in Mercury's Magnetosphere Derived from MESSENGER Magnetometer and Fast Imaging Plasma Spectrometer Observations

We assess the statistical spatial distribution of plasma in Mercury's magnetosphere from observations of magnetic pressure deficits and plasma characteristics by the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft. The statistical distributions of proton flux and pressure were derived from 10months of Fast Imaging Plasma Spectrometer (FIPS) observations obtained during the orbital phase of the MESSENGER mission. The Magnetometer-derived pressure distributions compare favorably with those deduced from the FIPS observations at locations where depressions in the magnetic field associated with the presence of enhanced plasma pressures are discernible in the Magnetometer data. The magnitudes of the magnetic pressure deficit and the plasma pressure agree on average, although the two measures of plasma pressure may deviate for individual events by as much as a factor of approximately 3. The FIPS distributions provide better statistics in regions where the plasma is more tenuous and reveal an enhanced plasma population near the magnetopause flanks resulting from direct entry of magnetosheath plasma into the low-latitude boundary layer of the magnetosphere. The plasma observations also exhibit a pronounced north-south asymmetry on the nightside, with markedly lower fluxes at low altitudes in the northern hemisphere than at higher altitudes in the south on the same field line. This asymmetry is consistent with particle loss to the southern hemisphere surface during bounce motion in Mercury's offset dipole magnetic field.

magnetic↗
NASA NTRS2013

Proposed US Contributions to LOFT

Proposed US Enhancements include:Tantalum X -ray collimator, Additional ground station, Large Observatory for X-Ray Timing (LOFT) instrument team participation, US science support center & data archive, and Science enabled by US hardware. High-Z material with excellent stopping power. Fabricated using a combination of laser micromachining and chemical etching. Known technology capable of producing high-aspect ratio holes and large open fractions. Reduces LOFT LAD background by a factor of 3. Telemetry formats for LOFT based upon RXTE/EDS experience. Ground system software and strategies for WFM based upon RXTE/ASM automated pipeline software. MSFC engineering trade studies supporting the Ta collimator. Burst alert triggers based upon Fermi/GBM and HETE-2. Science Enhancements Enabled by US Hardware include: Tantalum collimator: Reduces background by factor of 3. Improves sensitivity to faint sources such as AGN. Eliminates contamination by bright/variable sources. outside the LAD field of view. US Ground Station: Enables continuous telemetry of all events from the WFM. Allows LAD to observe very bright >500 mCrab sources with full event resolution.

Wilson-Hodge, Colleen↗
DOE OSTI2020

Characterization of flow and transport in a fracture network at the EGS Collab field experiment through stochastic modeling of tracer recovery

Energy extraction from subsurface reservoirs is important for addressing the increasing energy demand and environmental concerns such as global warming. However, the characterization of subsurface reservoirs, particularly reservoirs dominated by fracture networks remains a challenge due to the lack of means to directly observe subsurface processes. This study explores the feasibility and efficacy of characterizing fracture flow and transport processes in an enhanced geothermal system (EGS) testbed through stochastic tracer modeling. There are two enabling factors that allow application of stochastic modeling to characterize a subsurface reservoir. First, an abundance of geological and geophysical measurements enables the development of a high-fidelity and well-constrained fracture network model. Second, high-performance computing (HPC) allows running massive realizations efficiently. Six conservative tracer tests were stochastically modeled and produced satisfactory realizations that successfully reproduce field tracer recovery data from each tracer test. The evolution of flow and transport processes in the fracture network was then analyzed from these satisfactory realizations. This work demonstrates that stochastic tracer modeling on a high-fidelity fracture network model is feasible and can provide important insights regarding flow and transport characteristics in subsurface fractured reservoirs.

58 GEOSCIENCES↗
DOE OSTI2022

Fundamentals of Spark-Plasma Sintering (Final Report)

This project was focused on the development of the general theory of spark-plasma sintering (SPS) taking into account the role of both thermal and non-thermal factors in the acceleration of SPS mass transport. SPS is a particular kind of field-assisted sintering, which provides potentially revolutionary capabilities to the processing of materials into configurations previously unattainable. This approach significantly improves the processing time- and quality-wise. It carries the potential of maintaining the nano and sub-micron structure in nano-powder-based materials after consolidation. SPS gains particular prominence in connection with its exceptional potential of rapid and ultra-rapid processing of very hard-to-deform materials, which would typically require lengthy consolidation times at significantly elevated temperatures under conditions of conventional powder pressing or sintering. The achievement of the ultimate goal of the formulation of the general theory of spark plasma sintering required the identification of the contributions of all the thermal and non-thermal factors in the enhancement of mass transport under SPS processing conditions. As our research indicated, this enhancement is mostly reduced to the creation of the conditions of controlled non-equilibrium, which is especially important in ultra-rapid field-assisted sintering techniques. Thus, the main project objective was the analysis of the SPS physical basis at multiple scales specifically exploring the role of electric current in the acceleration of mass transport and with an emphasis on the conditions of controlled non-equilibrium.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Scaling behavior and giant field enhancement of the thermal conductivity in the honeycomb antiferromagnet BaCo 2⁢ (AsO 4 ) 2

The layered honeycomb material BaCo 2 (AsO 4 ) 2 is of topical interest because its magnetic state is related to that of the Kitaev magnet α-RuCl 3 . Using thermal transport to probe how magnetic excitations interact with phonons in the magnetically disordered regime, we have uncovered an unusually large enhancement of the thermal conductivity κ xx in an in-plane magnetic field H. Just above the Néel temperature T N , a field of 13 T increases κ xx by a factor of ∼ 211, which is very large compared to other magnetic insulators. Interestingly, κ xx (H, T) exhibits a scaling behavior in the entire magnetically disordered region that surrounds the ordered zigzag state. The ratio Δκ xx (H, T)/κ xx (13, T), measured throughout the disordered region, collapses to a one-parameter scaling function exp(−1/gx) (where x = μ B B/k B T and g is a constant).

36 MATERIALS SCIENCE↗
DOE OSTI2026

Chemically Enabled CO 2 -Enhanced Oil Recovery in Multi-Porosity, Hydrothermally Altered Carbonates in the Southern Michigan Basin (Final Technical Report)

This is the Final Technical Report for the project "Chemically Enabled CO 2 -Enhanced Oil Recovery in Multi-Porosity, Hydrothermally Altered Carbonates in the Southern Michigan Basin." Over the course of six years of collaboration between Battelle and project partners, all stated objectives of the program have been completed, including full geological characterization of the TBR trend (See companion report for Task2), laboratory and modeling experiments to determine the optimum composition and design of CO 2 -EOR operations in the TBR trend, execution of a field test of chemically-enhanced CO 2 in a TBR well, and integration of the data and learnings gathered during these efforts into a full-trend development plan. Detailed reporting on these activities, their outcomes, and implications for trend-wide development is provided in the report. This report and encompassed data will provide TBR field operators with detailed information on what worked, what did not work, and how to proceed with production optimization of their TBR assets using chemically-enhanced CO 2 -EOR. CO 2 -EOR is a relatively well understood and broadly implemented strategy for increasing incremental production across the oil and gas industry, but its application has been primarily focused on reservoirs with limited heterogeneity. The intention of this project was show first that the same physical mechanisms that improve recovery factors in homogeneous reservoirs (namely wettability alteration, viscosity alteration, oil swelling, and mobility control) are at play in heterogeneous reservoirs. This was proven by the project’s laboratory studies and dynamic simulations, with the potential exception of mobility control, which needs further study. The second intention was to demonstrate via direct field testing that CO 2 -EOR can work in a strongly heterogeneous reservoir. While the field test strategy implemented during this project did not succeed in producing oil, data gathered during the test sheds light on what may work for field operators who try chemically-enhanced CO 2 -EOR within their own reservoirs, significantly reducing the level of uncertainty carried by first-of-a-kind commercial efforts that could (and should) follow this test. Simultaneously, the project has identified several large-volume ethanol plants and other sources of CO 2 emissions in the region and provided a handrail that CO 2 emitters and field operators can leverage to capture, transport, and inject that CO 2 into their fields. This project has also shown that, in many cases, the economics of CO 2 -EOR in the TBR are attractive. And finally, by completing a project of this scope in the southern Michigan Basin, the project has contributed to the knowledge base and operational experience of field operators, state regulatory agencies, local service companies, and state universities, with CO 2 -EOR projects which should allow follow-on projects to proceed safely and efficiently.

02 PETROLEUM↗
DOE OSTI2023

Quantum Enhanced Probes of Magnetic Circular Dichroism

Magneto-optical microscopies, including optical measurements of magnetic circular dichroism, are increasingly ubiquitous tools for probing spin-orbit coupling, charge-carrier g-factors, and chiral excitations in matter, but the minimum detectable signal in classical magnetic circular dichroism measurements is fundamentally limited by the shot-noise limit of the optical readout field. Here, a two-mode squeezed light source is used to improve the minimum detectable signal in magnetic circular dichroism measurements by 3 decibels compared with state-of-the-art classical measurements, even with relatively lossy samples like terbium gallium garnet. Furthermore, these results provide a framework for new quantum-enhanced magneto-optical microscopies that are particularly critical for environmentally sensitive materials and for low temperature measurements where increased optical power can introduce unacceptable thermal perturbations.

42 ENGINEERING↗
DOE OSTI2022

Exclusive production of a pair of high transverse momentum photons in pion-nucleon collisions for extracting generalized parton distributions

We show that exclusive production of a pair of high transverse momentum photons in pion-nucleon collisions can be systematically studied in QCD factorization approach if the photon’s transverse momentum q T with respect to the colliding pion is much greater than Λ QCD . We demonstrate that the leading power non-perturbative contributions to the scattering amplitudes of this exclusive process are process-independent and can be systematically factorized into universal pion’s distribution amplitudes (DAs) and nucleon’s generalized parton distributions (GPDs), which are convoluted with corresponding infrared safe and perturbatively calculable short-distance hard parts. The correction to this factorized expression is suppressed by powers of 1/q T . We demonstrate quantitatively that this new type of exclusive processes is not only complementary to existing processes for extracting GPDs, but also capable of providing an enhanced sensitivity to the dependence of both DAs and GPDs on the active parton’s momentum fraction x. We also introduce additional, but the same type of exclusive observables to enhance our capability to explore GPDs, in particular, their x-dependence.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Designing Damage-Resistant Multilayer Dielectric Gratings for Petawatt-Class Lasers

We have successfully developed high efficiency dielectric gratings for chirped pulse amplification (CPA) pulse compression with a focus on improving damage thresholds for high peak power. Specifically, we focused on developing first-of-kind designs that operate at TM polarization. Unpublished modeling within our group shows that the electric field enhancement in the solid material for gratings operating at TM can be significantly less than for TE. Subsequently, the laser damage threshold of TM gratings should be higher by potentially a factor of 2X.

42 ENGINEERING↗
NASA NTRS2001

Stellar and Binary Evolution in Star Clusters

This paper presents a final report on research activities covered on Stellar and Binary Evolution in Star Clusters. Substantial progress was made in the development and dissemination of the "Starlab" software environment. Significant improvements were made to "kira," an N-body simulation program tailored to the study of dense stellar systems such as star clusters and galactic nuclei. Key advances include (1) the inclusion of stellar and binary evolution in a self-consistent manner, (2) proper treatment of the anisotropic Galactic tidal field, (3) numerous technical enhancements in the treatment of binary dynamics and interactions, and (4) full support for the special-purpose GRAPE-4 hardware, boosting the program's performance by a factor of 10-100 over the accelerated version. The data-reduction and analysis tools in Starlab were also substantially expanded. A Starlab Web site (http://www.sns.ias.edu/-starlab) was created and developed. The site contains detailed information on the structure and function of the various tools that comprise the package, as well as download information, "how to" tips and examples of common operations, demonstration programs, animations, etc. All versions of the software are freely distributed to all interested users, along with detailed installation instructions.

McMillan, Stephen L. W.↗
NASA NTRS2005

Trajectories and energy transfer of saltating particles onto rock surfaces : application to abrasion and ventifact formation on Earth and Mars

The interaction between saltating sand grains and rock surfaces is assessed to gauge relative abrasion potential as a function of rock shape, wind speed, grain size, and planetary environment. Many kinetic energy height profiles for impacts exhibit a distinctive increase, or kink, a few centimeters above the surface, consistent with previous field, wind tunnel, and theoretical investigations. The height of the kink observed in natural and wind tunnel settings is greater than predictions by a factor of 2 or more, probably because of enhanced bouncing off hard ground surfaces. Rebounded grains increase the effective flux and relative kinetic energy for intermediate slope angles. Whether abrasion occurs, as opposed to simple grain impact with little or no mass lost from the rock, depends on whether the grain kinetic energy (EG) exceeds a critical value (EC), as well as the flux of grains with energies above EC. The magnitude of abrasion and the shape change of the rock over time depends on this flux and the value of EG > EC. Considering the potential range of particle sizes and wind speeds, the predicted kinetic energies of saltating sand hitting rocks overlap on Earth and Mars. However, when limited to the most likely grain sizes and threshold conditions, our results agree with previous work and show that kinetic energies are about an order of magnitude greater on Mars.

planet sufraces↗
DOE OSTI2023

Impact of aquifer properties on the extent and timeline of CO 2 trapping

Abstract Geologic CO 2 sequestration in porous saline aquifers is a promising approach to reducing atmospheric concentrations of CO 2 . Reactive transport simulations provide the opportunity to analyze which factors influence geochemical reactivity in the reservoir, understand those most important for promoting CO 2 trapping, and assess individual sites. Field‐scale aquifer characterization is time and resource intensive such that here, reactive transport simulations are leveraged to enhance understanding of selected aquifer properties including porosity, permeability, depth of storage, and carbonate mineralogy on the overall CO 2 trapping potential to better select sites promoting geochemical reactivity for CO 2 trapping. There are different mechanisms for sequestrating CO 2 . Once injected, CO 2 will dissolve into the brine to create an acidic environment, resulting in the dissolution of pre‐injection formation minerals. Released ions can reprecipitate as secondary minerals. The dissolved CO 2 and mineralized CO 2 are considered as a more secure form of CO 2 trapping in this study compared to the free supercritical CO 2 . Here, a framework leveraging a controlled set of field scale simulations is developed to facilitate rapid, optimized site selection. Simulations vary aquifer properties to understand the impact of each unique property on CO 2 trapping, tracking, and comparing the amount of supercritical, aqueous, and mineralized CO 2 . The rate at which the CO 2 injected into the aquifer is converted to aqueous or mineralized CO 2 is newly defined here as the sequestration efficiency and used to compare simulation results. The reservoir depth and fraction of carbonate minerals in the formation are shown to be more important factors than reservoir porosity and permeability in affecting CO 2 trapping. However, the impact of aquifer properties on the evolution of injected CO 2 depends on the stage of the sequestration project. © 2023 Society of Chemical Industry and John Wiley & Sons, Ltd.

Energy & Fuels↗
DOE OSTI2023

Design of a Nanophotonic Hybrid Coupler

This project aims to design and simulate a nanophotonic hybrid coupler for detecting vacuum ultraviolet (VUV) light with higher efficiency. VUV light is of significant interest because of its applications ranging from high energy physics to space science and electronic industry. However, current VUV photodetectors have very low efficiencies because most materials absorb in the VUV region (100-200 nm). To address this challenge, I have designed a plasmonic-dielectric coupler with wavelength shifting properties, enabling high Purcell enhancement and far-field confinement. The coupler consists of a cylindrical cSi resonator on top of a thin ZnO layer, and Ag and SiO2 are used as substrates. Simulations are done using the finite-difference time domain method to solve Maxwell’s equations, and specifically with Meep and Lumerical. The effectiveness of the coupler is characterized by the Purcell factor and far-field radiation. The Purcell factor reaches a maximum near 390 nm and is in the o rder of 10^4. Furthermore, the coupler also allows partial control of the directionality of the far-field radiation. With the presence of the resonator, the radiation is directed towards the coupled metalens. Overall, our design combines the advantages of plasmonic and dielectric couplers, along with the intrinsic wavelength shifting properties of materials to enhance VUV detection significantly, and such a device can be used in, for example, the DUNE project.

Zhou, Jiayang↗
DOE OSTI2024

Non-linear MHD modelling of transients in tokamaks: a review of recent advances with the JOREK code

Transient magneto-hydrodynamic (MHD) events like edge localized modes (ELMs) or disruptions are a concern for magnetic confinement fusion power plants. Research with the MHD code JOREK towards understanding control of such instabilities is reviewed here in a concise way to provide a complete overview, while we refer to the original publications for details. Experimental validation for unmitigated vertical displacement events progressed. The mechanism of vertical force mitigation by impurity injection was identified. Two-way eddy current coupling to CARIDDI was completed. Shattered pellet injection was simulated in JET, KSTAR, ASDEX Upgrade (AUG) and ITER. Benign runaway electron beam termination in JET and ITER was studied. Coupling of kinetic REs to the MHD is ongoing and a virtual RE synchrotron radiation diagnostic was developed. Regarding pedestal physics, regimes devoid of large ELMs in AUG were simulated and predictive JT60-SA simulations are ongoing. For ELM suppression by resonant magnetic perturbations (RMPs), AUG, ITER and EAST simulations were performed. A free boundary RMP model was validated against experiments. Evidence for penetrated magnetic islands at the pedestal top based on AUG experiments and simulations was found. Simulations of the naturally ELM-free quiescent H-mode in AUG and HL-3 show external kink mode formation prevents pedestal build-up towards an ELM within windows of the edge safety factor. With kinetic neutral particles, high field side high density formation in ITER was simulated and with kinetic impurities, tungsten transport in AUG RMP plasmas was studied. To capture turbulent transport, electro-static full-f particle in cell models for ion temperature gradient and trapped electron modes were established and benchmarked. Application to RMP plasmas shows enhanced turbulence in comparison to unperturbed states. Energetic particle interactions with MHD were studied. Flux pumping that prevents the safety factor on axis from dropping below unity was simulated. First non-linear stellarator applications include current relaxation in $l$ = 2 stellarators, while verification for advanced stellarators progresses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1997

Effects of Fuel Preheat on Soot Formation in Microgravity Laminar Diffusion Flames

Nonbuoyant flames offer themselves as an attractive and promising platform to gain a better understanding of soot mechanisms. The effects of buoyancy can be eliminated temporarily in drop towers which sustain brief intervals of reduced gravity-typically lower than 10(exp -3)g- extending up to several seconds at a time. Microgravity facilities have been employed to show that nonbuoyant flames are longer, wider and sootier than their normal-gravity counterparts. Sunderland et al. recently verified the existence of smoke point in laminar nonbuoyant flames. As reported, microgravity flames operating above their smoke point displayed a blunt tip and much broader soot-containing regimes in comparison to their buoyant counterparts. Mortazavi et al. established that residence times in microgravity laminar jet diffusion flames with Re=0(100) tend to be proportional to burner diameter and inversely proportional to burner exit velocity. This offers the capability to alter residence times in nonbuoyant laminar jet diffusion flames when varying the burner exit diameters and velocities. Megaridis et al. presented a quantitative definition of the soot-field structure within laminar microgravity jet diffusion flames which operated well above their smoke point. The experimental methodology involved a full-field laser-light extinction technique and jet diffusion flames of nitrogen-diluted (50% vol.) acetylene fuel burning in quiescent air at atmospheric pressure. The work was conducted at the 2.2s drop tower of the NASA Lewis Research Center (NASA-LeRC). Parallel work on 1-g flames was also presented in (6) to facilitate comparisons on the effect of gravity on the soot fields. As reported, the soot spatial distributions in 0-g flames did not change in a detectable manner after 1s within a typical 2.2s experiment. During that period, the soot field was shown to sustain a pronounced annular structure throughout the luminous nonbuoyant-flame zone. The maximum soot volume fraction measured at 0-g was nearly a factor of two higher than that at 1-g, thus confirming the enhanced sooting tendency of nonbuoyant flames. Greenberg and Ku presented a similar study and reported trends that matched those of for the 50% (vol.) nitrogen-diluted acetylene fuel. Furthermore, they examined pure acetylene flames and reported similar trends with respect to the influence of gravity on maximum soot volume fractions and flame cross-section-averaged soot loadings. Both studies clearly demonstrated the improved spatial resolution of microgravity flames compared to their normal-gravity counterparts. The current study evaluates the influence of moderate fuel preheat on soot formation within 0-g laminar gas jet diffusion flames. While fuel temperature variations have little influence on residence times in 1-g, they have a much more significant effect in 0-g. The primary objective of this program is to quantify this effect and its consequences on sooting by comparing soot volume fraction distributions under preheated and unpreheated-fuel conditions. Furthermore, the current work aims at expanding the limited soot database available for nonbuoyant flames. Soot fields in such flames can be used to perform additional tests of recently developed soot sub-models which have the potential to become powerful predicting tools in combustion design.

Konsur, Bogdan↗