Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “erosion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Erosion of carbon/carbon by solar wind charged particle radiation during a solar probe mission

The possible erosion of a carbon/carbon thermal shield by solar wind-charged particle radiation is reviewed. The present knowledge of erosion data for carbon and/or graphite is surveyed, and an explanation of erosion mechanisms under different charged particle environments is discussed. The highest erosion is expected at four solar radii. Erosion rates are analytically estimated under several conservative assumptions for a normal quiet and worst case solar wind storm conditions. Mass loss analyses and comparison studies surprisingly indicate that the predicted erosion rate by solar wind could be greater than by nominal free sublimation during solar wind storm conditions at four solar radii. The predicted overall mass loss of a carbon/carbon shield material during the critical four solar radii flyby can still meet the mass loss mission requirement of less than 0.0025 g/sec.

Sokolowski, Witold↗

Investigation of Keeper Erosion in the NSTAR Ion Thruster

The goal of the present investigation was to determine the cause for the difference in the observed discharge keeper erosion between the 8200 hr wear test of a NASA Solar Electric Propulsion Technology Applications Readiness (NSTAR) engineering model thruster and the ongoing extended life test (ELT) of the NSTAR flight spare thruster. During the ELT, the NSTAR flight spare ion thruster experienced unanticipated erosion of the discharge cathode keeper. Photographs of the discharge keeper show that the orifice has enlarged to slightly more than twice the original diameter. Several differences between the ELT and the 8200 hr wear test were initially identified to determine any effects which could lead to the erosion in the ELT. In order to identify the cause of the ELT erosion, emission spectra from an engineering model thruster were collected to assess the dependence of keeper erosion on operating conditions. Keeper ion current was measured to estimate wear. Additionally, post-test inspection of both a copper keeper-cap was conducted, and the results are presented. The analysis indicated that the bulk of the ion current was collected within 2-mm radially of the orifice. The estimated volumetric wear in the ELT was comparable to previous wear tests. Redistribution of the ion current on the discharge keeper was determined to be the most likely cause of the ELT erosion. The change in ion current distribution was hypothesized to caused by the modified magnetic field of the flight assemblies.

Domonkos, Matthew T.↗

Factors Influencing Lava-Substrate Heat Transfer and Implications for Thermomechanical Erosion

We develop numerical simulations of basaltic lava flowing laminarly over a basalt substrate in order to examine the details of the lava dynamics and thermal boundary layers and to understand the implications for substrate heating. As the initial stage of a larger study of thermomechanical erosion in different planetary environments, we aim to understand why erosion occurs on Earth, why erosion features are not ubiquitous given the high temperatures involved, and whether it is a plausible mechanism for the formation of planetary channels such as lunar sinuous rilles and Venusian canali. Here we confine our attention to terrestrial lavas with well-known properties and eruption parameters. With relatively simple computational fluid dynamic simulations, most closely representing tube-fed hawaiian basalts (for which erosion has been documented), we demonstrate the importance of incorporating several key factors in models of lava flow/ substrate heat transfer, which have commonly been neglected in previous treatments. By addressing the interaction of the flow dynamics and heat transfer in the lava, our work suggests that the development of a temperature gradient in the base of the lava, even for undeveloped flow, has a significant influence on substrate temperature. The sensitivity of the lava-substrate interface temperature to the thermophysical properties of the lava and substrate suggests that a delicate balance is required for partial melting to occur. Thus, it might take weeks of continuous flow to initiate partial melting of the substrate at distances of several kilometers from the vent. These durations exceed the periods of stability typical of lava flowing in tubes; pauses, blockages, surges, and break-outs frequently disrupt the flow. However, natural irregularities in the flow dynamics or substrate topography might help to initiate and maintain substrate melting on shorter timescales by disturbing the intimately coupled dynamic and thermal boundary layers. Although a purely thermal mechanism cannot be ruled out, our findings support the premise that mechanical erosion may play a key role in reports of erosion based on field evidence.

Fagents, S. A.↗

NASA Glenn/AADC Collaboration Optimized Erosion Coatings for Inlet Guide Vanes

There is a need for lightweight, durable materials and structures to reduce the weight of propulsion systems. Polymer matrix composites (PMC's) are promising materials for aerospace applications because of their high strength-to-weight ratio relative to metals. Unfortunately, they are limited to applications where they are not exposed to hightemperature oxidizing atmospheres and/or particulates from ingested air. This is because oxidation and erosion occur on the surface, leading to weight loss, nodulation, and/or cracking on the surface, and a consequent decline of mechanical properties over time. Although prior research has shown that oxidation can be slowed when metallic or ceramic coatings are applied onto PMC's, there remains a need for erosion-resistant coatings that protect PMC's from high-velocity particulates in the engine flow path. These erosionresistant coatings could extend the life of polymer composites. Polymer composites are heavily damaged without an erosion-resistant coating because they are not as hard as metallic engine structures. The effectiveness and life of the coatings depends on their inherent properties as well as on the interaction between the coating and the PMC. Since polymers, in general, have high thermal expansion coefficients in comparison to metals and ceramics, failure of the coatings often occurs at this interface. The objective of this research is to develop strategies to improve this interface and tailor overlays for erosion resistance. The bondcoat, which was developed at the NASA Glenn Research Center, is composed of zinc blended with polyimides to improve the compatibility between the PMC and the overlay material. Initial coating trials at AADC produced vanes that had poor bonding between the overlay and bondcoats. Subsequently, Glenn successfully demonstrated that high-quality plasma-sprayed erosion coating systems could be applied to these guide vanes. Inlet guide vanes from AE 3007 engines fiber composites were coated using a coating system composed of a bondcoat and a hard topcoat. Optimization of the plasma spray process has led to plans for future erosion testing in gas turbine engine environments.

Sutter, James K.↗

Comparison of Atomic Oxygen Erosion Yields of Materials at Various Energy and Impact Angles

The atomic oxygen erosion yields of various materials, measured in volume of material oxidized per incident atomic oxygen atom, are compared to the commonly accepted standard of Kapton H (DuPont) polyimide. The ratios of the erosion yield of Kapton H to the erosion yield of various materials are not consistent at different atomic oxygen energies. Although it is most convenient to use isotropic thermal energy RF plasma ashers to assess atomic oxygen durability, the results can be misleading because the relative erosion rates at thermal energies are not necessarily the same as low Earth orbital (LEO) energies of approx.4.5 eV. An experimental investigation of the relative atomic oxygen erosion yields of a wide variety of polymers and carbon was conducted using isotropic thermal energy (approx.0.1 eV) and hyperthermal energy (approx.70 eV) atomic oxygen using an RF plasma asher and an end Hall ion source. For hyperthermal energies, the atomic oxygen erosion yields relative to normal incident Kapton H were compared for sweeping atomic oxygen arrival with that of normal incidence arrival. The results of isotropic thermal energy, normal incident, and sweeping incident atomic oxygen are also compared with measured or projected LEO values.

Banks, Bruce A.↗

Atomic Oxygen Erosion Yield Predictive Tool for Spacecraft Polymers in Low Earth Orbit

A predictive tool was developed to estimate the low Earth orbit (LEO) atomic oxygen erosion yield of polymers based on the results of the Polymer Erosion and Contamination Experiment (PEACE) Polymers experiment flown as part of the Materials International Space Station Experiment 2 (MISSE 2). The MISSE 2 PEACE experiment accurately measured the erosion yield of a wide variety of polymers and pyrolytic graphite. The 40 different materials tested were selected specifically to represent a variety of polymers used in space as well as a wide variety of polymer chemical structures. The resulting erosion yield data was used to develop a predictive tool which utilizes chemical structure and physical properties of polymers that can be measured in ground laboratory testing to predict the in-space atomic oxygen erosion yield of a polymer. The properties include chemical structure, bonding information, density and ash content. The resulting predictive tool has a correlation coefficient of 0.914 when compared with actual MISSE 2 space data for 38 polymers and pyrolytic graphite. The intent of the predictive tool is to be able to make estimates of atomic oxygen erosion yields for new polymers without requiring expensive and time consumptive in-space testing.

Bank, Bruce A.↗

MISSE 2 PEACE Polymers Experiment Atomic Oxygen Erosion Yield Error Analysis

Atomic oxygen erosion of polymers in low Earth orbit (LEO) poses a serious threat to spacecraft performance and durability. To address this, 40 different polymer samples and a sample of pyrolytic graphite, collectively called the PEACE (Polymer Erosion and Contamination Experiment) Polymers, were exposed to the LEO space environment on the exterior of the International Space Station (ISS) for nearly 4 years as part of the Materials International Space Station Experiment 1 & 2 (MISSE 1 & 2). The purpose of the PEACE Polymers experiment was to obtain accurate mass loss measurements in space to combine with ground measurements in order to accurately calculate the atomic oxygen erosion yields of a wide variety of polymeric materials exposed to the LEO space environment for a long period of time. Error calculations were performed in order to determine the accuracy of the mass measurements and therefore of the erosion yield values. The standard deviation, or error, of each factor was incorporated into the fractional uncertainty of the erosion yield for each of three different situations, depending on the post-flight weighing procedure. The resulting error calculations showed the erosion yield values to be very accurate, with an average error of 3.30 percent.

McCarthy, Catherine E.↗

Design and Performance Optimizations of Advanced Erosion-Resistant Low Conductivity Thermal Barrier Coatings for Rotorcraft Engines

Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future rotorcraft engine higher fuel efficiency and lower emission goals. For thermal barrier coatings designed for rotorcraft turbine airfoil applications, further improved erosion and impact resistance are crucial for engine performance and durability, because the rotorcraft are often operated in the most severe sand erosive environments. Advanced low thermal conductivity and erosion-resistant thermal barrier coatings are being developed, with the current emphasis being placed on thermal barrier coating toughness improvements using multicomponent alloying and processing optimization approaches. The performance of the advanced thermal barrier coatings has been evaluated in a high temperature erosion burner rig and a laser heat-flux rig to simulate engine erosion and thermal gradient environments. The results have shown that the coating composition and architecture optimizations can effectively improve the erosion and impact resistance of the coating systems, while maintaining low thermal conductivity and cyclic oxidation durability

Zhu, Dongming↗

MISSE 6 Stressed Polymers Experiment Atomic Oxygen Erosion Data

Polymers and other oxidizable materials used on the exterior of spacecraft in the low Earth orbit (LEO) space environment can be eroded away by reaction with atomic oxygen (AO). For spacecraft design, it is important to know the LEO AO erosion yield, Ey (volume loss per incident oxygen atom), of materials susceptible to AO erosion. The Stressed Polymers Experiment was developed and flown as part of the Materials International Space Station Experiment 6 (MISSE 6) to compare the AO erosion yields of stressed and non-stressed polymers to determine if erosion is dependent upon stress while in LEO. The experiment contained 36 thin film polymer samples that were exposed to ram AO for 1.45 years. This paper provides an overview of the Stressed Polymers Experiment with details on the polymers flown, the characterization techniques used, the AO fluence, and the erosion yield results. The MISSE 6 data are compared to data for similar samples flown on previous MISSE missions to determine fluence or solar radiation effects on erosion yield.

deGroh, Kim K.↗

A Dose Assessment Model for Radioactive Waste Exposed by Gully Erosion at West Valley - 20513

The Western New York Nuclear Service Center (WNYNSC), located approximately 48 km south of Buffalo, New York, is the site of a former nuclear fuel reprocessing and radioactive waste disposal facility. Spent nuclear fuel was processed there from 1966 to 1972, leaving behind radioactive and chemical wastes in two disposal areas and a waste tank farm. Site operations also resulted in releases of radioactivity to site soils, groundwater, and to surface waters draining the site. The New York State Energy Research and Development Authority (NYSERDA) and the U.S. Department of Energy (DOE) are collaborating in a process of decision making for decommissioning those facilities remaining at the WNYNSC following the completion of Phase 1 decommissioning. Neptune and Company, Inc. (Neptune) was contracted to develop a probabilistic performance assessment (PPA) computer model to assist the agencies in this process. The PPA Model includes a contaminant transport component focusing on the movement of contaminants within and among environmental media including groundwater and surface water transport, contaminant translocation by plants and animals, diffusion, and erosion. The model also includes evaluation of potential exposure and health effects for a Resident Farmer exposure scenario, where the Resident Farmer represents a critical group, described as that group of individuals reasonably expected to receive the greatest exposure to residual radioactivity for any applicable set of circumstances. The West Valley Site is located in the glaciated Allegheny Plateau region of western New York State. The waste reprocessing and disposal areas were constructed on a relatively fat area of plateau dissected by drainages of Buttermilk Creek, including Erdman Brook, Franks Creek, and Quarry Creek. An important aspect of the contaminant transport component of the PPA model is consideration of erosive processes such as slumping of the stream slopes and the advance of gullies from these streams. These erosion processes remove material from the plateau, growing the size of the creek valleys and making them wider and deeper. Of particular interest for the impact of erosion is radioactive waste contained in the Nuclear Regulatory Commission (NRC)-Licensed Disposal Area (NDA), the New York State-Licensed Disposal Area (SDA), and residual radiological inventory in the underground storage tanks at the Waste Tank Farm (WTF). The PPA Model is organized around geographically-defined facilities which were constructed upon the plateau, including the NDA, SDA, and WTF. Ongoing stream erosion processes will potentially transfer radioactive waste and residual inventory from these facilities to the ground surface on adjacent hillslope areas where erosion has breached the facility. Hence, it is important to evaluate the consequences of potential exposures to a Resident Farmer on the hillslopes below a breached facility. Two interrelated aspects of the dose assessment model related to hillslope exposure are discussed: 1) representation of the physical processes related to transport of radionuclides from facilities onto the hillslopes, and from the hillslopes into adjoining creeks where contaminated material migrates downstream with surface water and sediment, and; 2) adaptation of the activities associated with the Resident Farmer scenario to assess potential exposures to contamination in the hillslope areas. This discussion will cover the conceptual basis of the hillslope exposure and transport models, and also implementation in the PPA computer model. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

River bank erosion and accretion rates, and planform metrics of the East River, downstream of Gothic Colorado over intervals between 1955 and 2015

This dataset provides the tabular summary of analysis of an alluvial floodplain reach of the East River, downstream of Gothic, CO near Crested Butte. The measurements include bank erosion and accretion rates, channel width, bank curvature, and the aspect/orientation of the river banks. The measurements were derived from binary masks of the location of the river channel from aerial and satellite imagery collected on seven dates over a sixty-year timespan: 1955, 1973, 1983, 1990, 2001, 2011, and 2015. The masks were analyzed using the Spatially Continuous Riverbank Erosion and Accretion Measurements (SCREAM) software detailed in Rowland et al. 2016. The masks used in this analysis can be found an accompanying dataset (DOI: ). Rates of change along the East River were measured over a total of 8-time intervals: 1955-1973; 1955-2015; 1973-1983; 1983-1990; 1990-2001; 2001-2011; 2001-2015; and 2011-2015.In files with “summary” in the name, the data is provided at a pixel level, where each mapped bank pixel has an associated erosion or accretion value, a channel width, a curvature value, and an aspect each river and time period will have an individual file. Files with “Segments” in name provide data that is averaged along segments of the rivers. These segments are approximately 10 channel widths in length. In addition to erosion and accretion rates, the segment-based results include area measurements of erosion and accretion, islands, and channels. The number of islands is also included.

54 ENVIRONMENTAL SCIENCES↗

Effect of Microadding Amine Surfactant on Erosion-Corrosion Wear of Structural Steel in NPP

Corrosion processes, specifically, erosion-corrosion, are one of the causes of damage occurring in NPP equipment during operation. Measures are taken to prevent erosion-corrosion wear of thermal-power equipment and pipelines. One such measure is the development and adoption of water chemistry regimes that are capable of forming a protective fi lm on a metal surface. Octadecylamine is one such reagent. The results of laboratory tests and industrial experiments studying the effect of octadecylamine on the development of erosion-corrosion wear of NPP equipment are presented. The octadecylamine-hydrazine water chemistry regime at octadecylamine concentration 0.5 mg/dm{sup 3} reduces the rate of erosion-corrosion wear by about 15-fold. The positive effect of micro-additions of octadecylamine is confirmed by direct erosion-corrosion studies performed at the Kola NPP.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Studies on Enhancement of Silt Erosion Resistance of 13/4 Martensitic Stainless Steel by Low-Temperature Salt Bath Nitriding

Low-temperature salt bath nitriding of heat treated and tempered 13/4 Martensitic stainless steel (13/4HTT) was carried at 450 °C (N450) and 500 °C (N500) for 10 h each. The nitrided samples were characterized by using x-ray diffractometer, field emission scanning electron microscope and optical microscope. The nanohardness and elastic modulus of the cross section of nitrided specimen were measured by nanoindentation test using Hysitron TI950 triboindenter. The nitrided 13/4HTT (N450 and N500) and 13/4HTT specimens were subjected to slurry erosion test in a slurry pot tester. The test was conducted for 48 h, and weight loss was measured after every 6 h. The relative speed of slurry with respect to specimen was 4.55 m/s. It was found that the weight loss due to erosion of the N450 is 83% less than that of 13/4HTT and that of N500 was 92% more than that of 13/4HTT. The erosion mechanism is correlated to the phases present in the specimens. The improvement in the slurry erosion resistance of N450 is due to presence of expanded martensite (α{sub N}-Fe). Increasing the temperature of nitriding to 500 °C led to the decrease in the slurry erosion resistance of N500 due to the formation of brittle CrN phase.

36 MATERIALS SCIENCE↗

Effect of Microstructure and Properties of Ni-WC Composite Coatings on Their Solid Particle Erosion Behavior

Metal matrix composites (MMCs) of WC in Co or Ni matrices are widely used due to their high wear resistance. Previous studies showed that tailoring the mechanical properties through optimum WC content can significantly extend the life cycle of MMCs. In this study, composite coatings of Ni with various WC content ranging from 10 to 55 vol.% were cold sprayed using agglomerated WCNi powders and two different sizes of Ni powders, − 10 + 4 (d{sub 50} = 7 µm) referred to as Ni(7) and − 35 + 15 (d{sub 50} = 25 µm) to as Ni(25). Microstructural characterization, including the deformed structure of Ni splats and retention and distribution of WC, was performed by scanning electron microscopy (SEM). Composite coatings were subjected to solid particle erosion following ASTM G76-13 standard. At low WC content coatings, erosion occurred primarily by plastic deformation of Ni matrices and knocking out of WC particles. At high WC concentrations, network distribution of compacted WCNi particles in the matrices led to a significant drop in erosion rates of coatings, due to a change in erosion mechanism from severe cutting and plowing of Ni and WC dislodging to WCNi splats spalling. Composite coatings sprayed using finer size Ni powder were usually more erosion resistant.

36 MATERIALS SCIENCE↗

Modelling soil erosion in a Mediterranean watershed: Comparison between SWAT and AnnAGNPS models

Highlights: • Outputs, input data and time requirements are compared for SWAT and AnnAGNPS. • Models are assessed also in wet and dry seasons. • Most of the basin is under moderate or high risk of erosion. • SWAT and AnnAGNPS are compared with RUSLE2015 and PESERA. In this study, the simulations generated by two of the most widely used hydrological basin-scale models, the Annualized Agricultural Non-Point Source (AnnAGNPS) and the Soil and Water Assessment Tool (SWAT), were compared in a Mediterranean watershed, the Carapelle (Apulia, Southern Italy). Input data requirements, time and efforts needed for input preparation, strength and weakness points of each model, ease of use and limitations were evaluated in order to give information to users. Models were calibrated and validated at monthly time scale for hydrology and sediment load using a four year period of observations (streamflow and suspended sediment concentrations). In the driest year, the specific sediment load measured at the outlet was 0.89 t ha{sup −1} yr{sup −1}, while the simulated values were 0.83 t ha{sup −1} yr{sup −1} and 1.99 t ha{sup −1} yr{sup −1} for SWAT and AnnAGNPS, respectively. In the wettest year, the specific measured sediment load was 7.45 t ha{sup −1} yr{sup −1}, and the simulated values were 8.27 t ha{sup −1} yr{sup −1} and 6.23 t ha{sup −1} yr{sup −1} for SWAT and AnnAGNPS, respectively. Both models showed from fair to a very good correlation between observed and simulated streamflow and satisfactory for sediment load. Results showed that most of the basin is under moderate (1.4–10 t ha{sup −1} yr{sup −1}) and high-risk erosion (> 10 t ha{sup −1} yr{sup −1}). The sediment yield predicted by the SWAT and AnnAGNPS models were compared with estimates of soil erosion simulated by models for Europe (PESERA and RUSLE2015). The average gross erosion estimated by the RUSLE2015 model (12.5 t ha{sup −1} yr{sup −1}) resulted comparable with the average specific sediment yield estimated by SWAT (8.8 t ha{sup −1} yr{sup −1}) and AnnAGNPS (5.6 t ha{sup −1} yr{sup −1}), while it was found that the average soil erosion estimated by PESERA is lower than the other estimates (1.2 t ha{sup −1} yr{sup −1}).

54 ENVIRONMENTAL SCIENCES↗

Surface Erosion of Plasma-Facing Materials Using an Electrothermal Plasma Source and Ion Beam Micro-Trenches

Erosion characteristics of tungsten-alternative plasma-facing materials (PFMs) were tested under high heat flux conditions in the electrothermal plasma source facility at Oak Ridge National Laboratory. The PFMs of interest are high-purity β-3C chemical vapor deposition silicon carbide (SiC) and the MAX phases Ti 3 SiC 2 and Ti 2 AlC [MAX = chemical formula M n+1 AX n , where M is an early transition metal (such as Ti or Ta), A is an A-group element (such as Si or Al), and X is carbon or nitrogen]. Additionally, an erosion analysis method was developed using a combination of focused ion beam microscopy and scanning electron microscopy, carving micro-trench geometries into polished sample surfaces. Samples of SiC, Ti 3 SiC 2 , and Ti 2 AlC were exposed to the electrothermal plasma source alongside tungsten and monocrystalline silicon. Samples were exposed to a Lexan polycarbonate (C 16 H 14 O 3 ) electrothermal plasma stream in a He environment, at a specified impact angle, with infrared camera diagnostics. Edge localized mode–relevant heat fluxes of 0.9 to 1 GW/m 2 over 1-ms discharges were generated on the target surfaces. Tungsten samples exhibited pronounced melt-layer formation and deformation, with measured molten pits 2 to 10 μm in diameter and melt-layer depths of up to 7 μm deep. Surface erosion rates for Ti 3 SiC 2 and Ti 2 AlC ranged from 80 to 775 μm/s and 85 to 470 μm/s, respectively. Both MAX phases exhibited extreme surface fracture and material ejection, with damage depths past 4 μm for Ti 2 AlC and 11 μm for Ti 3 SiC 2 . Lastly, SiC displayed the best performance, in one case surviving 15 consecutive electrothermal plasma exposures with an average erosion rate of about 29 μm/s and no surface fracturing. SiC erosion rates ranged from 23 to 128 μm/s.

36 MATERIALS SCIENCE↗

Advances in neutral tungsten ultraviolet spectroscopy for the potential benefit to gross erosion diagnosis

A spectral survey of tungsten emission in the ultraviolet region has been completed in the DIII-D tokamak and the CTH torsatron to assess the potential benefit of UV emission for the diagnosis of gross W erosion. Here, a total of 29 W I spectral lines are observed from the two experiments using survey spectrometers between 200 and 400 nm with level identifications provided based on a structure calculation for many of the excited states that produce strong emission lines. Of the 29 observed lines, 20 have not previously been reported in fusion relevant plasmas, including an intense line at 265.65 nm which could be important for benchmarking the frequently exploited line at 400.88 nm. Nearly all of the observed spectral lines decay down to one of the six lowest energy levels for neutral W, which are likely to be long-lived metastable states. The impact of metastable level populations on the W I emission spectrum and any erosion measurement utilizing a spectroscopic technique is potentially significant. Yet, the high density of W I emission in the UV region allows for the possibly of determining the relative metastable fractions and plasma parameters local to the erosion region. Additionally, the lines observed in this work could be used to perform multiple independent gross erosion measurements, leading to more accurate diagnosis of gross tungsten erosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduced model of high-Z impurity redeposition and erosion in tokamak divertor and its application to DIII-D experiments

A reduced model of high-Z impurities erosion and redeposition is presented to analyze net erosion of tungsten material in divertor attached plasma conditions measured in DIII-D experiments. This reduced model is tailored to quantify the redeposition and the net erosion on high-Z material samples of sufficiently small dimensions to be considered exposed to uniform plasma conditions. For those uniform plasma conditions, the spatial distribution of redeposited high-Z impurities is well approximated by an analytical distribution characterized by a few parameters. The fraction of high-Z impurity eroding and redepositing on a material sample is then obtained by integrating this distribution across the material sample. Here, the ratio of net erosion rates of tungsten measured experimentally from tungsten samples of different sizes exposed to the same attached plasma conditions are well reproduced with this reduced model. It is shown that uncertainties induced by radially non-uniform plasma conditions in experiments can be significantly reduced by exposing samples to high density divertor plasma. Several enhanced experimental setups are proposed to measure and compare net erosion rates from samples of various areas during a single plasma experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗