Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “emissions control technologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Industrial ion source technology

Plasma probe surveys were conducted in a 30-cm source to verify that the uniformity in the ion beam is the result of a corresponding uniformity in the discharge-chamber plasma. A 15 cm permanent magnet multipole ion source was designed, fabricated, and demonstrated. Procedures were investigated for texturing a variety of seed and surface materials for controlling secondary electron emission, increasing electron absorption of light, and improved attachment of biological tissue for medical implants using argon and tetrafluoromethane as the working gases. The cross section for argon-argon elastic collisions in the ion-beam energy range was calculated from interaction potentials and permits calculation of beam interaction effects that can determine system pumping requirements. The data also indicate that different optimizations of ion-beam machines will be advantageous for long and short runs, with 1 mA-hr/cm being the rough dividing line for run length. The capacity to simultaneously optimize components in an ion-beam machine for a single application, a capacity that is not evident in competitive approaches such as diode sputtering is emphasized.

Kaufman, H. R.↗
NASA NTRS2004

2003 NASA Seal/Secondary Air System Workshop

The following reports were included in the 2003 NASA Seal/Secondary Air System Workshop:Low Emissions Alternative Power (LEAP); Overview of NASA Glenn Seal Developments; NASA Ultra Efficient Engine Technology Project Overview; Development of Higher Temperature Abradable Seals for Industrial Gas Turbines; High Misalignment Carbon Seals for the Fan Drive Gear System Technologies; Compliant Foil Seal Investigations; Test Rig for Evaluating Active Turbine Blade Tip Clearance Control Concepts; Controls Considerations for Turbine Active Clearance Control; Non-Contacting Finger Seal Developments and Design Considerations; Effect of Flow-Induced Radial Load on Brush Seal/Rotor Contact Mechanics; Seal Developments at Flowserve Corporation; Investigations of High Pressure Acoustic Waves in Resonators With Seal-Like Features; Numerical Investigations of High Pressure Acoustic Waves in Resonators; Feltmetal Seal Material Through-Flow; "Bimodal" Nuclear Thermal Rocket (BNTR) Propulsion for Future Human Mars Exploration Missions; High Temperature Propulsion System Structural Seals for Future Space Launch Vehicles; Advanced Control Surface Seal Development for Future Space Vehicles; High Temperature Metallic Seal Development for Aero Propulsion and Gas Turbine Applications; and BrazeFoil Honeycomb.

Steinetz, Bruce M.↗
NASA NTRSDate not supplied

Experimental Study of Aero-Propulsive Interactions for Electric Ducted Fan Arrays in Multiple Positions on a Wing

The Adaptable Distributed Electric Propulsion Testbed (ADEPT) Wing was tested in the NASA Langley 12-Foot Low-Speed Tunnel for the SUbsonic Single Aft eNgine (SUSAN) Electrofan 25% scale flight research vehicle, which aims to reduce emissions for commercial transport aircraft with electric propulsion technologies. The purpose of the test was to study the aero-propulsive effects across angle of attack and fan speed variations for several propulsor placements and array sizes, and to investigate how DEP can be leveraged for augmented lift and vehicle control. Six electric ducted fan (EDF) array placements were tested by positioning the fans along the leading and trailing edges on the top and bottom surfaces, as well as centered on the chord line in front of and behind the wing. Each fan placement configuration was tested with an array of one, three, and five EDFs to characterize an aero-propulsive extrapolation effect, and the bare wing was tested separately to provide baseline aerodynamic measurements. The results compare the longitudinal forces and moments for each configuration by analyzing the combined aero-propulsive interaction effects, and offer valuable insight into considerations for fan placement along a wing to enable the benefits of DEP integration.

Rose Weinstein↗
NASA NTRS1975

Advanced supersonic propulsion study, phase 2

A continuation of the NASA/P and WA study to evaluate various types of propulsion systems for advanced commercial supersonic transports has resulted in the identification of two very promising engine concepts. They are the Variable Stream Control Engine which provides independent temperature and velocity control for two coannular exhaust streams, and a derivative of this engine, a Variable Cycle Engine that employs a rear flow-inverter valve to vary the bypass ratio of the cycle. Both concepts are based on advanced engine technology and have the potential for significant improvements in jet noise, exhaust emissions and economic characteristics relative to current technology supersonic engines. Extensive research and technology programs are required in several critical areas that are unique to these supersonic Variable Cycle Engines to realize these potential improvements. Parametric cycle and integration studies of conventional and Variable Cycle Engines are reviewed, features of the two most promising engine concepts are described, and critical technology requirements and required programs are summarized.

Howlett, R. A.↗
NASA NTRS2000

CPL Applications on the EOS-TERRA Spacecraft

This presentation reviews the use of Capillary Pumped Loops on the EOS-TERRA spacecraft, It starts with a brief review of the status of CPL technology. On the TERRA spacecraft, CPL's will be used for thermal control of 3 instruments. The document reviews the ground testing, and states that life testing will continue to run for three year, even after the launch.The document has schematic diagrams of the EOS-AM spacecraft, the Advanced Spaceborne Thermal Emission and Reflection Radiometer - Thermal-Infrared Radiometer (ASTER-TIR) CPL configuration, the Advanced Spaceborne Thermal Emission and Reflection Radiometer - Short-Wave-Infrared Radiometer (ASTER-SWIR). The use of Measurements of Pollution In The Troposphere (MOPITTS) Capillary Pumped Heat Transport System (CPHTS) is reviewed, and the performance is summarized in several charts. The use of CPHTS in the ASTER-SWIR is reviewed. The loops in the ASTER-TIR module is also reviewed, and the problems with the second loop temperature control is discussed.

Ku, Jentung↗
NASA NTRS2004

RQL Fuel Shifting Sector Rig Test

The low emissions potential of a Rich-Quench-Lean (RQL) combustor for use in the HIgh Speed Civil transport (HSCT) application was evaluated as part of the NASA Critical Propulsion Components (CPC) Program. Fuel shifting as an approach to combustor control was evaluated in a multiple bank RQL combustor, utilizing reduced scale quench technology implemented in a convoluted linear with quench plate concept.

Holdeman, James D.↗
NASA NTRS1977

Emissions Reduction Technology Program

Combustor concepts having the potential for significantly lower emissions levels were investigated. The combustor emissions reduction was measured in an engine test. Emission characteristics common to all engine classes are shown. Multiple-burning zone combustors, specifically the double-annular and swirl-can combustors were studied. Airblast and air-assist fuel injection techniques were evaluated for emissions control potential. The combustor sceening and refining phases are summarized.

Jones, R. E.↗
NASA NTRS1975

Engine design considerations for 2nd generation supersonic transports

The environmental and economic goals projected for advanced supersonic transports will require revolutionary improvements in propulsion systems. Variable cycle engine concepts that incorporate unique components and advanced technologies show promise in meeting these goals. Pratt & Whitney Aircraft is conducting conceptual design studies of variable cycle engine concepts under NASA sponsorship. This paper reviews some of the design considerations for these engine concepts. Emphasis is placed on jet noise abatement, reduction of emissions, performance improvements, installation considerations, hot-section characteristics and control system requirements. Two representative variable cycle engine concepts that incorporate these basic design considerations are described.

Howlett, R. A.↗
NASA NTRS1977

Vehicle safety telemetry for automated highways

The emphasis in current, automatic vehicle testing and diagnosis is primarily centered on the proper operation of the engine. Lateral and longitudinal guidance technologies, including speed control and headway sensing for collision avoidance, are reviewed. The principal guidance technique remains the buried wire. Speed control and headway sensing, even though they show the same basic elements in braking and fuel systems, are proceeding independently. The applications of on-board electronic and microprocessor techniques were investigated; each application (emission control, spark advance, or anti-slip braking) is being treated as an independent problem is proposed. A unified bus system of distributed processors for accomplishing the various functions and testing required for vehicles equipped to use automated highways.

Hansen, G. R.↗
NASA NTRS2004

Overview of NASA Glenn Seal Developments

Turbine engine studies have shown that reducing high pressure turbine (HPT) blade tip clearances will reduce fuel burn, lower emissions, retain exhaust gas temperature margin and increase range. Dr. Lattime presented the design and development status of a new Active Clearance Control Test rig aimed at demonstrating advanced ACC approaches and sensors. Mr. Melcher presented controls considerations for turbine active clearance control. Mr. Geisheimer of Radatech presented an overview of their microwave blade tip sensor technology. Microwave tip sensors show promise of operation in the extreme gas temperatures present in the HPT location. Mr. Justak presented an overview of non-contacting seal developments at Advanced Technologies Group. Dr. Braun presented investigations into a non-contacting finger seal under development by NASA GRC and University of Akron. Dr. Stango presented analytical assessments of the effects of flow-induced radial loads on brush seal behavior. Mr. Flaherty presented innovative seal and seal fabrication developments at FlowServ. Mr. Chappel presented abradable seal developments at Technetics. Dr. Daniels presented an overview of NASA GRC s acoustic seal developments. NASA is investigating the ability to harness high amplitude acoustic waves, possible through a new field of acoustics called Resonant Macrosonic Synthesis, to effect a non-contacting, low leakage seal. Dr. Daniels presented early results showing the ability to restrict flow via acoustic pressures. Dr. Athavale presented numerical results simulating the flow blocking capability of a pre-prototype acoustic seal.

Steinetz, Bruce M.↗
NASA NTRSDate not supplied

SUbsonic Single Aft eNgine (SUSAN) Power/Propulsion System Hardware-in-the-Loop Test Results

Electrified Aircraft Propulsion (EAP) technology offers a promising path forward for reducing greenhouse gas emissions and other negative environmental effects from the commercial aviation sector. EAP systems can reduce fuel burn and improve performance over state-of the-art designs, however the increased complexity and highly coupled nature of these systems present challenges that require new control approaches. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a concept aircraft developed by NASA as a reference design for a commercial transport aircraft with a highly integrated hybrid-electric powertrain. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test of a control architecture developed for the SUSAN power/propulsion system (PPS). The test was performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at the NASA Glenn Research Center (GRC) and involved a real-time reference model of the SUSAN PPS and control system running with a sub-scale electro-mechanical system replacing one of the PPS subsystems. A side-by-side comparison of the simulated and real systems in the HIL test results shows that the control architecture functions well in both the simulation and the real-time HIL environment. In both cases the controller is able to simultaneously deliver the required thrust response and balance power levels between the electrical and turbomachinery subsystems.

Jonah J Sachs-Wetstone↗
NASA NTRSDate not supplied

SUbsonic Single Aft eNgine (SUSAN) Power/Propulsion System Hardware-in-the-Loop Test Results

Electrified Aircraft Propulsion (EAP) technology offers a promising path forward for reducing greenhouse gas emissions and other negative environmental effects from the commercial aviation sector. EAP systems can reduce fuel burn and improve performance over state-of the-art designs, however the increased complexity and highly coupled nature of these systems present challenges that require new control approaches. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a concept aircraft developed by NASA as a reference design for a commercial transport aircraft with a highly integrated hybrid-electric powertrain. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test of a control architecture developed for the SUSAN power/propulsion system (PPS). The test was performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at the NASA Glenn Research Center (GRC) and involved a real-time reference model of the SUSAN PPS and control system running with a sub-scale electro-mechanical system replacing one of the PPS subsystems. A side-by-side comparison of the simulated and real systems in the HIL test results shows that the control architecture functions well in both the simulation and the real-time HIL environment. In both cases the controller is able to simultaneously deliver the required thrust response and balance power levels between the electrical and turbomachinery subsystems.

EAP↗
NASA NTRS1973

Electromagnetic interference of power conditioners for solar electric propulsion

Electrical, multikilowatt power conditioning (PC) equipment needed on board a spacecraft utilizing solar electric propulsion creates an electromagnetic environment that is potentially deterimental to the science, navigation, and radio communication hardware. Within the scope of the solar electric propulsion system technology program, three lightweight, 2.5-kW PCs were evaluated in terms of their electromagnetic characteristics. It was found that the levels of radiated and conducted interference exceeded the levels anticipated for a solar electric propulsion mission. These noise emissions, however, were the result of deficient interference design in these models, rather than a basic inability to control interference in this type of PC.

Whittlesey, A. C.↗
NASA NTRS1977

Symposium on Combustion /International/, 16th, Massachusetts Institute of Technology, Cambridge, Mass., August 15-20, 1976, Proceedings

Aspects of combustion technology in power systems are considered, taking into account a combustion in large boilers, the control of over-all thermal efficiency of combustion heating systems, a comparison of mathematical models of the radiative behavior of a large-scale experimental furnace, a concentric multiannular swirl burner, and the effects of water introduction on diesel engine combustion and emissions. Attention is also given to combustion and related processes in energy production from coal, spray and droplet combustion, soot formation and growth, the kinetics of elementary reactions, flame structure and chemistry, propellant ignition and combustion, fire and explosion research, mathematical modeling, high output combustion systems, turbulent flames and combustion, and ignition, optical, and electrical properties.

Source record↗
NASA NTRSDate not supplied

CFD Evaluation Of Sustainable Aviation Fuel Blends for Commercial Supersonics Technology

An overview is provided of a CFD study on the impacts of fuel blends on NOx emissions and flame structure in an axially staged combustor operating at a supersonic cruise condition. The Open version of the National Combustion Code (OpenNCC) was used to perform two-phase reacting flow computations with various blending ratios of an ‘average’ Jet-A (A2) and Gevo Alcohol-to-Jet (C1) for RTRC’s Axially Controlled Stoichiometry (ACS) combustor. The predicted flame structures in the ACS combustor with three different blending ratios of the A2 and C1 fuel were very similar. The predicted NOx emissions for all fuel blends were within 10% of the experimentally measured range of NOx emissions for 100% A2 fuel.

gas turbine combustion↗
NASA NTRS1982

Science and technology results from the OSS-1 Payload on the Space Shuttle

The OSS-1 Payload of nine experiments was carried on the STS-3 Space Shuttle flight in March of 1982. The OSS-1 Payload contained four instruments that evaluated specific aspects of the Orbiter's environment, including the levels of particulate, gaseous and electromagnetic emissions given off by the Orbiter, and the interactions between the Orbiter and the surrounding plasma. In addition to these environmental observations, these instruments performed scientific investigations in astronomy and in space plasma physics, including active experiments in electron beam propagation. Other experiments were in the areas of solar physics, plant growth, micrometeorite studies and the technology of actively controlled heat pipes. A description is given of the initial results from these experiments, with some implications of these results for future operation of space experiments from the Shuttle payload bay. One major result was the unexpected discovery of a faint surface-induced optical glow created near the Shuttle surfaces by impacts of ambient atmospheric atoms and molecules.

Chipman, E.↗
NASA NTRS1983

Science and technology results from the OSS-1 payload on the Space Shuttle

The OSS-1 Payload of nine experiments was carried on the STS-3 Space Shuttle flight in March of 1982. The OSS-1 Payload contained four instruments that evaluated specific aspects of the Orbiter's environment, including the levels of particulate, gaseous and electromagnetic emissions given off by the Orbiter, and the interactions between the Orbiter and the surrounding plasma. In addition to these environmental observations, these instruments performed scientific investigations in astronomy and in space plasma physics, including active experiments in electron beam propagation. Other experiments were in the areas of solar physics, plant growth, micrometeorite studies and the technology of actively controlled heat pipes. We present the initial results from these experiments, with some implications of these results for future operation of space experiments from the Shuttle payload bay. One major result was the unexpected discovery of a faint surface-induced optical glow created near the Shuttle surfaces by impacts of ambient atmospheric atoms and molecules.

short duration↗
NASA NTRSDate not supplied

CFD Evaluation of Sustainable Aviation Fuel Blends for Commercial Supersonics Technology

An overview is provided of a CFD assessment with advanced fuel blends to assess fuel impacts on NOx emissions and flame structure in an axially-staged combustor for NASA’s Commercial Supersonic Transport (CST) Program. The National Combustor Code (OpenNCC) was used to perform two-phase reacting flow computations with various blending ratios of two different aviation fuels, ‘average’ Jet-A (A2) and GEVO-ATJ (C1), for UTRC’s Axially Controlled Stoichiometry (ACS) combustor at CST cruise conditions. The predicted flame structures in the ACS combustor with three different blending ratios of A2 and C1 fuel were very similar to each other. The predicted NOx emissions for all fuel blends were within 10% of the experimentally measured NOx emissions for 100% A2 fuel.

Gas Turbine Combustion↗