The Beam Plasma Interactions Experiment: An Active Experiment Using Pulsed Electron Beams
Not Available
79 ASTRONOMY AND ASTROPHYSICS↗
SEARCH · Engineering Papers
Results for “electron beams”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effects of a 4.3T superconducting wiggler on the electron beam optics and dynamics at NSLS-II
A superconducting wiggler (SCW) with a peak field of 4.3 T has recently been installed at NSLS-II. The wiggler generates a high-flux X-ray beam with a photon energy range from 20 keV to 200 keV for the High Energy Engineering X-ray Scattering beamline. This device induces significant distortions in the electron beam orbit and optics. Here, we have corrected these adverse effects using feed-forward tables. The effects of the SCW on the electron beam emittance, energy spread, and bunch length were calculated and measured. The beam-induced heating of the cryogenic vacuum chamber was also studied. Finally, the superconducting wiggler has been commissioned for user operations.
36 MATERIALS SCIENCE↗
Probing potential energy landscapes via electron-beam-induced single atom dynamics
Structure, bonding, and chemical dynamics of reactions at surfaces and interfaces, and therefore most material properties are intrinsically tied to the energetic landscape in which each atom resides. Here, we demonstrate that a moving atom under electron beam excitation can be used to probe the energy landscape along (confined) step edges, providing information about atomic-scale potentials. In conclusion, the techniques for experimentally exploring atomic potentials holds promise for predictive atom-by-atom fabrication using electron beams.
36 MATERIALS SCIENCE↗
Electron Beam Treatment of Ballast Water
Members from the Great Waters Research Collaborative (GWRC), a project of the University of Wisconsin-Superior (UWS) Lake Superior Research Institute (LSRI), will be bringing two water types to simulate the electron beam removal process for ballast waters. These two types are named low challenge and high challenge. The Low Challenge water is highly transparent water with very low concentration of total suspended solids and dissolved organic carbon. The High Challenge water is like Duluth-Superior Harbor water with low transparency and higher concentration of total suspended solids and dissolved organic carbon. Both water types will undergo a series of applied electron beam radiations and analysis to meet ballast water discharge standards. For the analysis there are standard test organisms that will be evaluated for mortality. Heterotrophic bacteria (E. coli) along with Selenastrum capricornutum will be used and then Eucyclops spp. (or Hyalella azteca) and Daphnia magna will also be evaluated.
43 PARTICLE ACCELERATORS↗
Electron Beam Longitudinal Tracking (EBLT) v1.0
It is a serial/parallel code for fast electron beam longitudinal forward or backward tracking through an electron linear accelerator. This codes includes longitudinal space-charge effect, structure and resistive wall wakefields, and longitudinal coherent synchrotron radiation effect. To use it as a parallel code, please comment out the "use mpistub" in BeamBunch.f90, rename mpif.h as mpif.hh, and use the Makefile_parallel as Makefile.
Qiang, Ji↗
Thin-Foil Heating with Intense Relativistic Electron Beams
Thin-metal foils are used in intense relativistic beam experiments for various purposes. In planning these experiments and analyzing the results it is often desirable to have an estimate of the temperature reached during the beam pulse. This can be deduced from an estimate of the energy deposited by the beam, and the specific heat capacity of the material, which depends on the temperature. The methodology for doing this is explained herein, and a metric for foil survivability under heating by an intense relativistic electron beam is suggested.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
Fatigue crack growth resistance of a mesoscale composite microstructure Haynes 282 fabricated via electron beam melting additive manufacturing
Materials synthesis via additive manufacturing gives unprecedented control over the solidified microstructure. While a number of studies have demonstrated the ability to produce spatially varying microstructures, little work exists to understand the behavior of such “composite” materials. In this work, we utilized electron beam melting to process Ni-based superalloy Haynes 282 and produce compact tension samples with a spatially varying mesoscale structure. Fatigue crack growth experiments reveal that the crack growth rate is dependent on the degree of microstructural heterogeneity. This work demonstrates that the crack growth resistance can be tailored within a component using electron beam melting additive manufacturing.
36 MATERIALS SCIENCE↗
Transport of kJ-laser-driven relativistic electron beams in cold and shock-heated vitreous carbon and diamond
We report experimental results on relativistic electron beam (REB) transport in a set of cold and shock-heated carbon samples using the high-intensity kilojoule-class OMEGA EP laser. The REB energy distribution and transport were diagnosed using an electron spectrometer and x-ray fluorescence measurements from aCu tracer buried at the rear side of the samples. The measured rear REB density shows brighter and narrower signals when the targets were shock-heated. Hybrid PIC simulations using advanced resistivity models in the target warm-dense-matter (WDM) conditions confirm this observation. We show that the resistivity response of the media, which governs the self generated resistive fields, is of paramount importance to understand and correctly predict the REB transport.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Degradation of Poly- and Perfluoroalkyl Substances (PFAS) in Water via High Power, Energy-Efficient Electron Beam Accelerator
The goal of the 2-year workplan was to see if electron beam (EB) could be used to break down a sub-set of the larger chemical family of per and polyfluoroalkylated substances (PFAS) in an energy efficient and economical manner when compared to conventional water treatment technologies. Year one (Y1) work focused on sample EB treatment work in the Fermi National Accelerator Laboratory’s (FNALs) Accelerator Applications Demonstration and Development (A2D2) EB accelerator. While there are reportedly thousands of types of PFAS, for the point of most of the work herein, a small subset was examined, typically perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA). PFOA and PFOS are two of the most well studied PFAS and are studied for baseline evaluations and are considered most useful. The work from Y1 provided information about the optimal operating parameters and additives to use when treating PFOS and PFOA via EB. The data were then used to see where in a water treatment system an EB accelerator would be best suited to treat PFAS. A conventional water treatment technology, GAC, was then compared to e-beam treatment technology with respect to energy and costs for treatment. In year two (Y2), several conventional e-beam accelerator designs, and FNAL’s developmental compact SRF accelerator design, were evaluated for their suitability in PFAS treatment, from an energy efficiency and cost standpoint. Several EB parameters were evaluated and optimized for the removal of PFOA and PFOS from water at normal pressure and temperature, measured as total PFAS removal. Under the optimized test conditions both PFOA showed complete destruction to inorganic fluoride, and PFOS to inorganic fluoride and sulfate, with mass balance. The effect on PFAS removal relative to solution pH, total EB dose, EB dose rate, dissolved oxygen concentration (DO), temperature, and initial PFAS concentration were evaluated. In general, PFOA was easier to destroy than PFOS. Degradation products, typically observed under less-than-optimal EB conditions, provided insight to degradation mechanisms. Products were identified to rule out possible deleterious biproduct formation. The water radiolysis radical reaction kinetics with PFOS and PFOA were not dependent on the initial concentration over 5-orders of magnitude from 2 μg/L to 20 mg/L. This is thought to be because there was an overabundance of the reactive water radiolysis radicals relative to PFAS molecules and largely attributed to aqueous electrons. The reaction rates appeared to be diffusion limited. Testing at higher concentrations (100-200 mg/L) showed a decrease in removal efficiency, suggesting alternative kinetics, possibly second order rates, at higher concentrations. In all, we successfully defined a set of optimal EB parameters to treat PFOA and PFOS at concentrations of 20 mg/L in water with destruction efficiencies near 100%. We further tested the optimized EB parameters with other types of PFAS, including shorter and longer fluorocarbon chain homologs of PFOA and PFOS, and PFAS with alternative functional groups such as sulfonamides. Based on our results EB can be optimized as an effective destructive technology for removing PFAS from water. The conditions optimized for PFOA and PFOS were less effective with ultra-short fluorocarbon compounds like TFMS, PFES, PFPS and PFBS, and likely require re-optimization of parameters to them. In all, it was determined that from a cost and energy efficiency standpoint, EB would be best applied to waste streams with relatively high concentrations of PFOS and PFOA and is not as cost effective as GAC treatment for removing low concentrations of PFAS from water. Higher concentrations of PFAS can be found in the wastewater of conventional treatment processes such as RO and IE and therefore EB may be used to supplement such treatment technologies. Some real-world IE regeneration wash water and RO reject water containing higher concentrations of PFAS and obtained from pilot scale industrial wastewater treatment system at a fluorochemical manufacturing facility, showed that EB could remove PFAS from such types of wastewaters. The IE regenerant wash water appeared to be the most efficient of the two types of wastewaters tested. However, some further optimization of the EB parameters for the specific PFAS types present in those wastewaters may be required. Also, the effects of co-present TOC and mineral salts should be considered during such optimization efforts. From the experimental Y1 results it was seen that the aqueous electron drives degradation of the PFAS. In a hypothetical water treatment skid using EB for PFAS destruction the parameters of the system should be optimized to promote aqueous electron production. Before EB treatment, the PFAS should be preconcentrated when possible, the pH should be raised to pH 10 or higher to enhance aqueous electron production, and the water should be nitrogen purged to remove dissolved oxygen to minimize aqueous electron scavenging. An excel spreadsheet was created that calculates optimal conditions based on inlet PFAS concentration and desired outlet concentration, by optimizing the accelerator power, dose rate, water treatment rate, pH and dissolved oxygen levels to reach the desired endpoint. Given this information on accelerator operating conditions five different EB accelerator systems were compared. One EB system was a continuous-wave, linear superconducting accelerator being designed at Fermilab. Three other EB systems (IMPELA at 5% and 25% duty factor and the ILU-14) were normal conducting pulsed linear accelerators. The fifth system was an IBA Rhodotron which is a normal conducting, circular, continuous-wave accelerator. The accelerator efficiency (% of the incoming power that is used in water treatment) was the dominating factor in accelerator choice. The radio frequency (RF) power supply and the accelerator design (superconducting versus warm technology) drive the accelerator efficiency. The IBA Rhodotron was seen to be the most energy efficient commercially available technology with a wall-plug (total) power efficiency of 43% at 400 kW. The Fermilab design, with a prototype for a different application currently being fabricated, was the most energy efficient at 55% when driven by a Klystron RF power supply and as high as 77% when powered by a magnetron. As the Fermilab design was the most energy efficient by approximately 10-30%, further design work was done on the accelerator and beam delivery system specific to the destruction of PFAS in water. The Fermilab design is unique from industrial accelerators in that is superconducting. Superconducting technology allows for the acceleration of electrons without losses. The accelerator must be cooled to below the point where it is superconducting and is operated around 4 degrees Kelvin. The bulk of the design work for the accelerator is on making the accelerator as energy efficient as possible so that it does not require liquid helium and can be cooled with conduction cooling via cryocoolers. Final design work resulted in an EB accelerator that would operate at minimally 200 kW and 10 MeV. Prototype construction would cost $\$ $7.8 million dollars when driven by a Klystron power supply. A second version of the same accelerator would cost $\$ $5.5 million dollars when driven by a magnetron that is still under development. The commercially available 300 kW IBA Rhodotron cost was estimated at approximately $\$ $9 million. While it is hard to directly compare, an operational GAC system used by 3M for groundwater treatment capital cost (2022 dollars) was estimated to cost $\$ $3.3 million. While the capital expense of the EB accelerator systems was higher than GAC, the accelerator EB treatment would result in destruction of the PFAS and not just sequestration of PFAS to form a new waste stream that requires further treatment or disposal. The operating cost to destroy the PFAS via 400 kw EB system was less than $\$ $1000/kg of PFAS destroyed when treating at a 20 mg/L PFAS concentration, compared to GAC with operating costs that calculated at $\$ $27,530 per kg of PFAS sequestered when treating 100 μg/L PFOA and PFOS combined concentration.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Electron beam characterization via quantum coherent electric field imaging
We demonstrate an all-optical, minimally invasive electron beam (𝑒−beam) characterization using Rydberg electrometry. An 𝑒-beam passes through a localized detector volume containing thermal Rb atoms that are optically excited in a quantum superposition of ground and Rydberg states. The 𝑒-beam's electric field perturbs atomic coherence and modifies resonance fluorescence in a narrow spectral region near the two-photon optical transition. Imaging Rb fluorescence provides a map of the electric field from the 𝑒-beam via Rydberg state Stark shifts and allows us to reconstruct the 𝑒-beam width, centroid position, and current. For an 𝑒-beam of 20 keV and electron currents of 20–40 µA, we measured the centroid position with an accuracy of ≤ 8 µm and width to within 100 µm, limited by the experimental sensitivity of electric field reconstruction of ∼0.02 V/cm. This method is suitable for a wide range of electron energies and currents, and can be adopted for nuclear and high-energy experiments for minimally invasive real-time diagnostics and profiling of charged particle beams.
Behary, Rob [College of William and Mary, Williams↗
Investigation of CrMnV and CrMnTiV multi principal element alloys thin films for use as exit windows of electron beam accelerators
Here, this study explores CrMnV and CrMnTiV multi principal element alloy (MPEA) films as candidates for electron beam exit windows in industrial, high-power accelerators. Films were deposited via magnetron sputtering on various substrates and exposed to 66 kGy of 10 MeV e-beam irradiation. Structural and mechanical properties were analyzed using FESEM, XRD, and nanoindentation. CrMnTiV films exhibited superior grain uniformity and hardness, regardless of the substrate type. Compared to bulk materials, both MPEA films demonstrated higher hardness and excellent radiation resistance. These results highlight the potential of MPEA films as durable, radiation-tolerant materials for high-performance accelerator exit window applications.
Electron Beam Irradiation↗
Reversible Electron-Beam Patterning of Colloidal Nanoparticles at Fluid Interfaces
The directed self-assembly of colloidal nanoparticles (NPs) using external fields guides the formation of sophisticated hierarchical materials but becomes less effective with decreasing particle size. As an alternative, electron-beam-driven assembly offers a potential avenue for targeted nanoscale manipulation, yet remains poorly controlled due to the variety and complexity of beam interaction mechanisms. Here, we investigate the beam–particle interaction of silica NPs pinned to the fluid–vacuum interface of ionic liquid droplets. In these experiments, scanning electron microscopy of the droplet surface resolves NP trajectories over space and time while simultaneously driving their reorganization. With this platform, we demonstrate the ability to direct particle transport and create transient, reversible colloidal patterns on the droplet surface. By tuning the beam voltage, we achieve precise control over both the strength and sign of the beam–particle interaction, with low voltages repelling particles and high voltages attracting them. This response stems from the formation of well-defined solvent flow fields generated from trace radiolysis of the ionic liquid, as determined through statistical analysis of single-particle trajectories under varying solvent composition. Altogether, electron-beam-guided assembly introduces a versatile strategy for nanoscale colloidal manipulation, offering new possibilities for the design of dynamic, reconfigurable systems with applications in adaptive photonics and catalysis.
36 MATERIALS SCIENCE↗
Electron Beam Powder Bed Fusion Additive Manufacturing of Refractory Metals
The processing of refractory metals via additive manufacturing (AM) presents an opportunity to fabricatecomponents not possible through traditional powder metallurgy techniques. However, processing via AM isextremely challenging and there exist a host of technological limitations still unaddressed. Molybdenumand tungsten are two materials of particular interest for nuclear energy generation applications. Themajority of existing work on the processing of these materials is focused on laser powder bed fusion whereasa smaller body of work exists for electron beam melting AM. In general, material with acceptable densitycan be obtained via both routes however cracking is much more difficult to mitigate against. Strongcrystallographic fiber textures have been observed across a range of refractory systems. In this work wepresent our recent findings on electron beam melting AM of pure tungsten and molybdenum. Wedemonstrate that defect-free material can be obtained in both systems with appropriate processing. Strongbuild direction crystallographic texture fibers are observed in both systems. In molybdenum the fibertexture has direct impact on the resulting tensile behavior. These results demonstrate that electron beamAM is a suitable technology for processing these difficult to fabricate materials.
Fernandez-Zelaia, Patxi↗
Manipulating ferroelectric behaviors via electron-beam induced crystalline defects
Ferroelectric nanoplates are attractive for applications in nanoelectronic devices. Defect engineering has been an effective way to control and manipulate ferroelectric properties in nanoscale devices. Defects can act as pinning centers for ferroelectric domain wall motion, altering the switching properties and domain dynamics of ferroelectrics. However, there is a lack of detailed investigation on the interactions between defects and domain walls in ferroelectric nanoplates due to the limitation of previous characterization techniques, which impedes the development of defect engineering in ferroelectric nanodevices. In this study, we applied in situ biasing transmission electron microscopy to explore how dislocation loops, which were judiciously introduced into barium titanate nanoplates via electron beam irradiation, affect the motion of ferroelectric domain walls. The results show that the motion was dramatically suppressed by these localized defects, because of the local strain fields induced by the defects. Additionally, the pinning effect can be further enhanced by multiple domain walls embedded with defect arrays. These results indicate the possibility of manipulating domain switching in ferroelectric nanoplates via the electron beam.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
Electron Modulational Instability in the Strong Turbulent Regime for an Electron Beam Propagating in a Background Plasma
We study collective processes for an electron beam propagating through a background plasma using simulations and analytical theory. A new regime where the instability of a Langmuir wave packet can grow locally much faster than ion frequency is clearly identified. The key feature of this new regime is an electron modulational instability that rapidly creates a local Langmuir wave packet, which in its turn produces local charge separation and strong ion density perturbations because of the action of the ponderomotive force, such that the beam-plasma wave interaction stops being resonant. Three evolution stages of the process and observed periodic burst features are discussed. In conclusion, different physical regimes in the plasma and beam parameter space are demonstrated for the first time.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Ultrafast quantum dynamics driven by the strong space-charge field of a relativistic electron beam
Here, we illustrate how the Coulomb field of a highly relativistic electron beam can be shaped into a broadband pulse suitable for driving ultrafast and strong-field physics. In contrast to a solid-state laser, the Coulomb field creates a pulse which can be intrinsically synchronized with an x-ray free electron laser (XFEL), can have a cutoff frequency which is broadly tunable from THz to EUV, and which acts on target systems as a “half-cycle” impulse. Explicit examples are presented to emphasize how the unique features of this excitation can be a tool for novel science at XFEL facilities like the LCLS.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
Corrosion evaluation of Ti–6Al–4V manufactured by electron beam melting in Ringer’s physiological solution: an in vitro study of the passive film
We report that electrochemical characteristics and semiconducting behavior of additively manufactured electron beam melted (EBM) and wrought (WR) Ti–6Al–4V (Ti-G5) are compared in Ringer’s physiological solution. X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM) confirmed the α+β structure of the tested materials, with two different microstructure types of “bimodal” and “basket-weave” for WR and EBM, respectively. Potentiodynamic polarization (PDP) revealed that the corrosion current density for EBM (i corr =0.27±0.06 μA cm -2 ) is less than the WR (i corr =0.70±0.05 μA cm -2 ). Moreover, potentiostatic polarization (PS) that was employed to form the passive layers at three different potentials of 300, 500, and 700 mV Ag/AgCl , showed that the passive films on the EBM sample are thinner. This finding was confirmed by electrochemical impedance spectroscopy (EIS). Furthermore, through Mott–Schottky (M–S) analysis, donor densities on WR passive films were found to be ~1.5 times larger than EBM. Although PS and EIS confirmed that the passive layer on EBM is thinner, it provides higher corrosion resistance than WR. The passive layer on both samples were found to have n-type characteristics with a duplex structure.
36 MATERIALS SCIENCE↗
An examination of different representations of the electrostatic field and potential of an intense relativistic electron beam in a cylindrical conductor and their implications on foil focusing of an elliptical beam
Knowledge of the electrostatic field and potential of an intense relativistic electron beam (IREB) in a cylindrical conductor is essential for understanding the transport of IREBs including the interaction of a grounded conducting foil with the beam. Different representations of the electrostatic field or potential exist in the literature. The different representations are compared and an extension to foil focusing of elliptical beams is discussed.
43 PARTICLE ACCELERATORS↗