SEARCH · Engineering Papers

Results for “ducts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Noise from a Supersonic Round Jet Discharging Into a Duct

In an effort to understand an 'unwanted noise' problem occasionally encountered in ground test facilities, the interaction of a jet flow with a duct is studied in a model scale experiment. While the interaction of subsonic jets was studied earlier, that of supersonic jets is considered in this paper. The effect of the presence of a cylindrical duct in the path of the jet is studied through sound pressure level spectral measurements as well as schlieren flow visualization. When the jet involves screech tones the placement of the duct is found to make only minor effects on the tones themselves as well as on the high frequency noise. However, there is increased energy at low frequencies. The increase in low frequency noise becomes clearer when screech is eliminated from the jet by two small tabs placed at the nozzle exit. It is shown that spectral peaks and increased sound pressure levels occur at frequencies corresponding to the axial acoustic resonance modes of the duct. These peaks persist into the supersonic regime, however, their amplitudes diminish relative to increasing spectral amplitudes at other frequencies with increasing jet Mach number. A wire-mesh screen attached to the end of the duct effectively suppresses such unwanted noise at subsonic as well as supersonic conditions.

Jet Noise↗

NASA NTRS2019

FUN3D and USM3D Analysis of the Propulsion Aerodynamic Workshop 2018 S-Duct Test Case

This work presents the results of Fun3D and USM3D analyses that were performed for the 4th AIAA Propulsion Aerodynamics Workshop (PAW). The PAW workshop is separated into three sections that focus on internal duct flows, nozzle flows and a special topic. This paper focuses on the internal duct flow section of PAW04 while an accompanying paper discusses the analyses performed for the nozzle portion. For the internal duct flow section, the PAW04 participants were provided with the two configurations consisting of an S-duct with and without aerodynamic interface plane (AIP) rake legs modeled. The participants were asked to perform a grid refinement study as well as a turbulence model study for the configuration with the rake legs. The analyses discussed here were performed on custom grids developed under the guidelines of the workshop. Additionally, the paper discusses the development and use of flow controllers for matching the desired flow characteristics. The results show that both solvers do well for predicting internal flow characteristics of the S-duct based on direct comparison with the experimental data. However, the CFD-to-CFD comparison proved to be more challenging due to the localized occurrence of supersonic flow near the rake legs when using the mass flow controller. A turbulence model study was performed to compare the two-equation SST model to the SA-QCR model. The results show that although the turbulence model does affect the solution, it makes a minimal impact on pressure recovery and inlet distortion intensity for this case. Suggestions for future workshops include gridding guidelines similar to those employed for the Drag Prediction Workshop series for the grid refinement study and a time accuracy study.

Carter, Melissa B.↗

NASA NTRS1962

Experimental Research on 4-Duct Tandem VTOL Aircraft Configurations

This paper presents a brief summary of several wind-tunnel investigations conducted at the Langley Research Center of the NASA to study the aerodynamic and stability and control characteristics of several VTOL aircraft configurations powered by four tilting ducted propellers arranged in tandem pairs. Specifically the two rear ducts could be mounted close alongside the upper rear portion of the fuselage with small wing panels attached to the outboard side of the ducts or could be mounted outboard on the tips of a small wing located high on the rear portion of the fuselage. The two front ducts were always mounted close inboard on the forward part of the fuselage and could be mounted either in a high or low position on the fuselage. The results of the investigation indicated that aircraft of this type could have acceptable aerodynamic and static longitudinal and lateral stability and control characteristics in both transition and normal cruise flight except for the possible qualification that the lateral force due to sideslip is abnormally high and might cause the aircraft to be too sensitive to side gusts.

VTOL AIRCRAFT↗

NASA NTRS1972

A study of internal drag of small-scale ducts at Mach number 4

An experimental investigation was made to examine the applicability of methods used to determine internal drag of small ducts and to study some of the problems encountered in assessing momentum losses in such ducts. Test Mach numbers ranged from 3.7 to 4.4 at angles of attack of 0 and 5 degrees and at a constant Reynolds number of 4.3 million per foot. The configurations represented small ducts used to simulate external aerodynamics of air breathing propulsion systems and consisted of wing nacelle models of ducts with circular, square, and rectangular inlets and with a two-dimensional inlet.

Graham, L. A.↗

NASA NTRS1971

On propagation of long waves in curved ducts.

Propagation of waves in curved ducts and pipes belong to the class of motion which is characterized by wave patterns totally different from those known in straight ducts or in unlimited space. The curvilinear boundaries are responsible for the appearance of a continuous standing radial wave which in turn affects the transmitted tangential waves. The purpose of this paper is to solve the problem of propagation of long acoustic waves in slightly and sharply bent ducts. This problem has been only partially analyzed by various authors. In this study two acoustic systems are considered which allow determination of the basic modes of motion and describe the transition and distortion of plane waves as they propagate down the curved channel. A detailed study of the behavior of waves in junctions between straight and curved ducts is also given. Solutions and expressions for principal modes of the wave are obtained by using the linearized equation of motion solved for its characteristic values. This original approach required a novel use of Bessel functions to determine the characteristic values of the steady and the decaying fields of motion.

Rostafinski, W.↗

NASA NTRS1973

Propagation of waves of acoustic frequencies in curved ducts

The propagation of waves of acoustic frequencies in curved ducts is studied for the first four modes. The analysis makes use of Bessel functions to construct curves of wave number in the duct versus imposed wave number. The results apply to ducts of arbitrary width and arbitrary radii of curvature. The characteristics of motion in a bend are compared with propagation of waves in a straight duct, and important differences in the behavior of waves are noted.

Rostafinski, W.↗

NASA NTRS1974

Spinning mode sound propagation in ducts with acoustic treatment

A detailed theoretical study of the acoustic propagation of spinning modes in acoustically treated open circular ducts is described. The suppressor with splitter rings was modeled by using the rectangular approximation to the annular duct. The theoretical models were used to determine optimum impedance and maximum attenuation for several spinning lobe numbers from 0 to 50. Some interesting results of the analysis are that for circular ducts the maximum possible attenuation and the optimum wall impedance are strong functions of the lobe number. For annular ducts the attenuation and optimum wall impedance are insensitive to the spinning lobe number for well cut-on modes. The above results help explain why suppressors with splitter rings were quite effective in spite of the lack of detailed information on the noise source modal structure.

Rice, E. J.↗

NASA NTRS1973

Propagation of plane waves in flow through a variable area duct

Duct geometry is an important factor that influences the transmission of sound in a duct. Nonconstant area produces variations in steady flow quantities through the duct, which can cause reflections of acoustic disturbances and the creation of standing wave patterns, and which can attenuate and disperse propagating waves. To study the problem, a second-order-accurate numerical method has been developed. The method of characteristics is used to solve the acoustic equations with the assumption of quasi-one-dimensional flow in the duct. Numerical results are presented over a broad range of frequencies. Low-frequency results are compared with approximate solutions for compact nozzles and high-frequency calculations are compared with results from the short-wave theory. The numerical results are also compared with an analytical solution of the acoustic equations for exponential horn sections with zero mean flow to further establish the validity of the numerical method.

King, L. S.↗

NASA NTRS1973

Noise generation by ducted combustion systems

Analysis of the interaction between a zone of nonsteady combustion and its confining duct shows that resonant type oscillations occur with resulting noise intensities far greater than from corresponding unconfined flame zones. The blading action on the flow through the compressor and turbine of an engine generates discrete frequency noise which, it is found, is enhanced by the response of the combustion zone in between. Ducted combustor experiments verify the predicted resonant type noise, the amplitude and frequency of which are strongly influenced by the duct dimensions and end impedance. A convergent exit nozzle results in stronger internal resonant noise oscillations but also generates a higher jet velocity, with the attendant jet noise which exceeds noise from inside the duct at jet Mach numbers near unity.-

Chiu, H. H.↗

NASA NTRS1974

Algebraically growing waves in ducts with sheared mean flow

Analysis of the behavior of standing and traveling acoustic waves in a smooth duct with a fluid flow having a sheared mean velocity profile, when the waves grow algebraically as they travel along the duct axis. It is shown that standing waves growing algebraically with the axial distance cannot exist in a smooth duct when the duct wall have a finite resistance. The existence of traveling waves subject to the same law of growth is also dismissed under realistic flow conditions.

Nayfeh, A. H.↗

NASA NTRS1974

Analysis of propagation of waves of acoustic frequencies in curved ducts

The propagation of waves of acoustic frequencies in curved ducts of rectangular cross section is studied for the first four modes. The analysis makes use of Bessel functions of the order (n + 1/2) to construct curves of wavenumber in the duct versus imposed wavenumber and to determine the profile of vibrational velocities. A wide range of duct widths and unrestricted radii of curvature have been considered. The characteristics of motion in a bend are compared with propagation of waves in a straight duct, and important differences in the behavior of waves are noted.

Rostafinski, W.↗

NASA NTRS1975

Spinning mode sound propagation in ducts with acoustic treatment

Recent acoustic data show larger noise attenuations than predicted for acoustically treated aircraft engine inlets without splitter rings. A theoretical study of the acoustic propagation of spinning modes in acoustically treated open circular ducts is presented, and a suppressor with splitter rings was modeled by using the rectangular approximation to the annular duct. Theoretical models were used to determine optimum impedance and maximum attenuation for several spinning lobe numbers from 0 to 50. Results of the analysis indicate that for circular ducts the maximum possible attenuation and the optimum wall impedance are strong functions of the lobe number, and for annular ducts the attenuation and optimum wall impedance are insensitive to the spinning lobe number for well cut-on modes. These results explain why suppressors with splitter rings were quite effective in spite of the lack of detailed information on the noise source modal structure. Conversely, effective use of outer wall treatment alone will require expanded knowledge of the noise source structure. Approximate solutions are presented to help interpret the more exact theoretical results.

Rice, E. J.↗

NASA NTRS1975

Dynamic instability of ducts conveying fluid

A finite element analysis was used to study dynamic instability in ducts conveying high speed fluids. Ducts examined include cantilevered curved, flexibly supported, arbitrarily shaped, and composite duct systems. Partial differential equations were used to study the duct systems.

Yu, Y. Y.↗

NASA NTRS1974

Spinning mode sound propagation in ducts with acoustic treatment

Recent acoustic data have shown larger noise attenuations than predicted for acoustically treated aircraft engine inlets without splitter rings. These data have stimulated a more detailed theoretical study of the acoustic propagation of spinning modes in acoustically treated open circular ducts. In addition, the suppressor with splitter rings was modeled by using the rectangular approximation to the annular duct. The theoretical models were used to determine optimum impedance and maximum attenuation for several spinning lobe numbers from 0 to 50. It is found that for circular ducts the maximum possible attenuation and the optimum wall impedance are strong functions of the lobe number. For annular ducts the attenuation and optimum wall impedance are insensitive to the spinning lobe number for well cut-on modes. The results help explain why suppressors with splitter rings have been quite effective in spite of the lack of detailed information on the noise-source modal structure. Conversely, effective use of outer-wall treatment alone will require expanded knowledge of the noise-source structure. Approximate solutions are presented to help interpret the more exact theoretical results.

Rice, E. J.↗

NASA NTRS1975

Acoustic eigenmodes of corrugated ducts

Acoustic propagation in two-dimensional corrugated ducts is analyzed. A transform is made to a coordinate system that matches the duct walls. The resulting wave equation separates in space and time. The spatial differential equation is then solved by expanding in the eigenfunctions of a flat-walled duct. The prescription for this expansion is given by the appropriate application of time-independent perturbation theory. Calculations of first-order corrections for a periodic duct of both finite and infinite length are presented.

Succi, G. P.↗

NASA NTRS1975

Duct wall impedance control as an advanced concept for acoustic impression

Models and tests on an acoustic duct liner system which has the property of controlled-variable acoustic impedance are described. This is achieved by a novel concept which uses the effect of steady air flow through a multi-layer, locally reacting, resonant-cavity absorber. The scope of this work was limited to a 'proof of concept.' The test of the concept was implemented by means of a small-scale, square-section flow duct facility designed specifically for acoustic measurements, with one side of the duct acoustically lined. The test liners were designed with the aid of previously established duct acoustic theory and a semi-empirical impedance model of the liner system. Over the limited range tested, the liner behaved primarily as predicted, exhibiting significant changes in resistance and reactance, thus providing the necessary concept validation.

Dean, P. D.↗

NASA NTRS1975

Optimization of duct acoustic liners of finite length

Lining design procedures generally ignore the effects of discontinuous impedance changes on reflection and modal redistribution of incident energy. The present study involves identification of the mechanisms of optimal suppression by segmented liners, including impedance discontinuity effects. The mathematical model involves rectangular ducts in the absence of mean flow. Segmented acoustic fields are represented by duct eigenfunction expansions, and mode matching is used to ensure continuity of the total field. Extensive parameter studies were used to identify attenuation mechanisms and to define preliminary liner configurations. These are used as starting values in conjugate-gradient optimization studies. Optimal segmented liners are presented and it is shown that, if the sound source is sufficiently well-defined, conventional infinite duct optimum attenuation rates can be improved upon by taking advantage of wall impedance discontinuities. Finally, follow-on work which will involve experimental verification and extension to the case with mean flow in the duct is described.

Beckemeyer, R. J.↗

NASA NTRS1976

Experimental-analytical correlation of optimum duct acoustic liner performance

Mode matching and segmented duct analytical models have been developed to take advantage of relative placement of liner segments in the design of optimal duct acoustic liners of one, two, and three segments. This paper presents experimental results which were obtained for liners installed in a rectangular duct for the case with no mean airflow through the duct. Excellent correlation is shown between the analytical and experimental data, thus verifying the analytical procedures used to design the optimum segmented lining configurations.

Patterson, J. D.↗