Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “converter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Revisiting Theoretical Limits for One-Degree-of-Freedom Wave Energy Converters

This work revisits the theoretical limits of one-degree-of-freedom wave energy converters. This paper considers the floating sphere used in the Ocean Energy Systems Task 10 Wave Energy Converter modeling and verification effort for analysis. Analytical equations are derived to determine bounds on the motion amplitude, time-averaged power, and power-take-off (PTO) force. A unique result was found that shows the time-averaged power absorbed by a wave energy converter can be defined solely by the inertial properties and radiation hydrodynamic coefficients. In addition, a unique expression for the PTO force amplitude was derived that has provided upper and lower bounds when resistive control is used to maximize power generation. For complex conjugate control, this same expression can only provide a lower bound, as there is theoretically no upper bound. These bounds are used to compare the performance of a floating sphere if it were to extract energy using surge or heave motion. The analysis shows that because of the differences in hydrodynamic coefficients of each oscillating mode, there will be different frequency ranges that provide better power capture efficiency. The influence of a motion constraint on power absorption while also utilizing a nonideal power take-off is examined and found to reduce the losses associated with bidirectional energy flow. The expression to calculate the time-averaged power with a nonideal PTO is modified by the mechanical-to-electrical efficiency and the ratio of the PTO spring and damping coefficients. The PTO spring and damping coefficients were separated in the expression, which allows for limits to be set on the possible values of PTO coefficients to ensure a net flow of power to the grid.

50 EE - Wind and Water Power Program - Water (EE-4↗
DOE OSTI2022

Power Converter Circuit Design Automation using Parallel Monte Carlo Tree Search

The tidal waves of modern electronic/electrical devices have led to increasing demands for ubiquitous application-specific power converters. A conventional manual design procedure of such power converters is computation- and labor-intensive, which involves selecting and connecting component devices, tuning component-wise parameters and control schemes, and iteratively evaluating and optimizing the design. To automate and speed up this design process, we propose an automatic framework that designs custom power converters from design specifications using Monte Carlo Tree Search. Specifically, the framework embraces the upper-confidence-bound-tree (UCT), a variant of Monte Carlo Tree Search, to automate topology space exploration with circuit design specification-encoded reward signals. Moreover, our UCT-based approach can exploit small offline data via the specially designed default policy and can run in parallel to accelerate topology space exploration. Further, it utilizes a hybrid circuit evaluation strategy to substantially reduce design evaluation costs. Empirically, we demonstrated that our framework could generate energy-efficient circuit topologies for various target voltage conversion ratios. Compared to existing automatic topology optimization strategies, the proposed method is much more computationally efficient --- the sequential version can generate topologies with the same quality while being up to 67% faster. Here, the parallelization schemes can further achieve high speedups compared to the sequential version.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Co-Design of Marine Energy Converters for Autonomous Underwater Vehicle Docking and Recharging - Software and Data

Software and testing data from the OH Hinsdale Wave lab for DOE-funded project on Co-Design of Marine Energy Converters for Autonomous Underwater Vehicle Docking and Recharging. This project will perform foundational research and testing to accelerate the sector-wide development and deployment of marine energy converters to provide Power-At-Sea. Specifically, we seek to overcome known challenges and knowledge gaps for the successful co-design of coupled Wave Energy Converter (WEC)-Autonomous Underwater Vehicles (AUV) systems; systems designed and tested for WEC array system health and environmental monitoring applications. This project brings together an experienced, multi-institution, and multi-disciplinary team to focus on the co-design of marine energy (ME) technologies and AUV docking systems, including multi-body hydrodynamic modeling, active control, autonomy, and hardware interfaces necessary to enable new WEC-focused understanding, and allow for robust and ubiquitous AUV docking and recharging in real-world conditions.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Benchmarking Real-Time Control Platforms Using a Matlab/Simulink Coder with Applications in the Control of DC/AC Switched Power Converters

In the control of DC/AC switched power converters (SPC), one of the most important aspects to be considered is the selection of the real-time control platform. The real-time control platform must be able to meet the high performance efficiency and regulation requirements of the DC/AC SPC, as these typically operate at switching frequencies in the order of kHz to MHz. For this reason, the hardware characteristics of the ADC and PWM, and the processing capacity of the real-time control platform are of vital importance when implementing advanced digital controllers that maintain voltage and current levels within regulatory standards. In this context, we aimed to perform a comparative study of the computation times of different real-time control platforms when implementing different control strategies for DC/AC switched power converters. We also analyzed the impact of the real-time control platforms on the THD of the voltages generated by the DC/AC switched power converters. With the help of this paper, researchers and developers will have criteria to select which real-time control platform to use in real-time control for DC/AC SPC applications.

42 ENGINEERING↗
DOE OSTI2022

Load-Packaged AC/DC and DC/DC Power Electronics Converter Performance Data

This data set contains experimentally characterized performance data from load-packaged alternating current to direct current (AC/DC) and direct current to direct current (DC/DC) power electronics converters associated with lighting devices and miscellaneous electrical loads typically found in commercial buildings in the United States. The data set contains input power, output power, efficiency, and harmonic spectrum data for 58 AC/DC converters and 35 DC/DC converters.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Grid Value Investigation of Medium-Voltage Back-to-Back Converters: Preprint

This paper presents the work which investigates the value that the medium voltage back to back (MVB2B) converter can bring to the grid, through two potential applications: voltage regulation powered by the reactive power adjustment function, and the distributed energy resource (DER) adoption enhancement powered by the quantitative power transfer function. Two groups of distribution systems have been prepared for the value investigation, including IEEE 123-bus system for voltage regulation study and two utility provided realistic distribution systems for DER adoption enhancement study. The analysis results have demonstrated that the MVB2B converter can bring significant value to the grid through the two aforementioned applications. Particularly, with MVB2B converter transferring power between two feeders, a substantial amount of backfeeding solar power can be avoided, and the size of the energy storage which is used to store the extra solar power can be significantly reduced.

28 EE - Advanced Manufacturing Office (EE-5A)↗
DOE OSTI2020

A New Configuration of Paralleled Modular ANPC Multilevel Converter Controlled by an Improved Modulation Method for 1 MHz, 1 MW EV Charger

In this work, a new configuration of the modular multilevel converter (MLC) based on the parallel connection of three-level active-neutral-point-clamped (3L-ANPC) cells as well as its improved modulation method is proposed for 1 MHz, 1 MW electric vehicle (EV) megacharger. In the proposed paralleled modular ANPC-MLC, only six high-frequency silicon carbide (SiC) power switches operating at 333 kHz are required to generate 1 MHz switching frequency spectrum. Moreover, the operating voltage of all power devices is halved, the magnitude of the first switching frequency harmonic cluster is decreased by the factor of five, and the load current is equally distributed between the 3L-ANPC legs by employing the proposed improved modulation method. Hence, the modularity, efficiency, and power density of the proposed converter are notably increased, whereas the value of passive components and the overall switching loss are remarkably decreased. In addition, an optimized design of the one 3L-ANPC cell of the proposed paralleled modular ANPC-MLC for 1 MHz, 1MW EV megacharger using Ansys SIwave, Icepak, and Q3D finite element method platforms is presented and analyzed in detail. The provided experimental results of the down-scaled setup verify the feasibility and viability of the proposed configuration as well as its improved switching pattern.

42 ENGINEERING↗
DOE OSTI2022

Binder-Free Wood Converted Carbon for Enhanced Water Desalination Performance

Here, the design and synthesis of high-performance and economical carbon electrodes play a critical role in developing energy-efficient water desalination technologies. As a sustainable approach, low-cost and abundant biomass materials are promising candidates to prepare porous carbon for capacitive deionization. In this study, binder-free porous carbon sheets are successfully prepared using natural balsa, pine, and basswood by thermal carbonization and treated by chemical activation. The carbon electrode materials converted from balsa and pine exhibit a comparable salt adsorption performance by capacitive deionization due to the extensive surface area, substantial electrical property, and superior hydrophilic performance. The following activation treatment of the balsa-converted carbon further enhances the surface and electrical properties and benefits the desalination performance. The salt adsorption capacity of the activated balsa electrode exhibits 12.45 mg g -1 . Additionally, 19.52 mg g -1 Pb 2+ and 20.06 mg g -1 Cr 3+ heavy metal adsorption capacity is also observed with the activated balsa electrode in 100 mg L -1 PbCl 2 and 50 mg L -1 CrCl 3 , respectively. To the best of authors’ knowledge, this is the highest NaCl adsorption capacity performance reported thus far by using pure wood converted carbon as the electrode, and these promising results indicate that activated balsa is an extraordinary material for water desalination.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of Heave Plate Hydrodynamic Force Parameterization on a Two-Body Wave Energy Converter

Heave plates are one approach to generating the reaction force necessary to harvest energy from ocean waves. In a Morison equation description of the hydrodynamic force, the components of drag and added mass depend primarily on the heave plate oscillation. These terms may be parameterized in three ways: (1) as a single coefficient invariant across sea state, most accurate at the reference sea state, (2) coefficients dependent on the oscillation amplitude, but invariant in phase, that are most accurate for relatively small amplitude motions, and (3) coefficients dependent on both oscillation amplitude and phase, which are accurate for all oscillation amplitudes. We validate a MATLAB model for a two-body point absorber wave energy converter against field data and a dynamical model constructed in ProteusDS. We then use the MATLAB model to evaluate the effect of these parameterizations on estimates of heave plate motion, tension between the float and heave plate, and wave energy converter electrical power output. We find that power predictions using amplitude-dependent coefficients differ by up to 30% from models using invariant coefficients for regular waves ranging in height from 0.5 to 1.9 m. Amplitude- and phase-dependent coefficients, however, yield less than a 5% change when compared with coefficients dependent on amplitude only. This suggests that amplitude-dependent coefficients can be important for accurate wave energy converter modeling, but the added complexity of phase-dependent coefficients yields little further benefit. We show similar, though less pronounced, trends in maximum tether tension, but note that heave plate motion has only a weak dependence on coefficient fidelity. Finally, we emphasize the importance of using experimentally derived added mass over that calculated from boundary element methods, which can lead to substantial under-prediction of power output and peak tether tension.

dynamical model↗
DOE OSTI2025

Converting sWeights to probabilities with density ratios

The use of machine learning approaches continues to have many benefits in experimental nuclear and particle physics. One common issue is generating training data which is sufficiently realistic to give reliable results. Here we advocate using real experimental data as the source of training data and demonstrate how one might subtract background contributions through the use of probabilistic weights which can be readily applied to training data. The sPlot formalism is a common tool used to isolate distributions from different sources. However, the negative sWeights produced by the sPlot technique can cause training problems and poor predictive power. This article demonstrates how density ratio estimation can be applied to convert sWeights to event probabilities, which we call drWeights. The drWeights can then be applied to produce the distributions of interest and are consistent with direct use of the sWeights. This article will also show how decision trees are particularly well suited to convert sWeights, with the benefit of fast prediction rates and adaptability to aspects of experimental data such as the data sample size and proportions of different event sources. We also show that a density ratio product approach in which the initial drWeights are reweighted by an additional converter gives substantially better results.

Glazier, Derek I. [Univ. of Glasgow, Scotland (Uni↗
DOE OSTI2024

Co-design of a wave energy converter for autonomous power

A "bolt-on" wave energy converter is designed to provide power for sensors on an existing oceanographic buoy. The narrow-banded pitch/roll response of the target oceanographic buoy lends itself to a tuned-resonator design, for which we suggest a novel "pitch resonator" wave energy converter concept. Using a pseudo-spectral method, the performance of the proposed wave energy converter is modeled in the range of sea states expected to be present at the target deployment location to study the e

Coe, Ryan Geoffrey↗
DOE OSTI2023

Kinetic simulations of ignited mode cesium vapor thermionic converters

Cesium vapor thermionic converters are an attractive method of converting high-temperature heat directly to electricity, but theoretical descriptions of the systems have been difficult due to the multi-step ionization of Cs through inelastic electron–neutral collisions. This work presents particle-in-cell simulations of these converters, using a direct simulation Monte Carlo collision model to track 52 excited states of Cs. Here, these simulations show the dominant role of multi-step ionization, which also varies significantly based on both the applied voltage bias and pressure. The electron energy distribution functions are shown to be highly non-Maxwellian in the cases analyzed here. A comparison with previous approaches is presented, and large differences are found in ionization rates due especially to the fact that previous approaches have assumed Maxwellian electron distributions. Finally, an open question regarding the nature of the plasma sheaths in the obstructed regime is discussed. The one-dimensional simulations did not produce stable obstructed regime operation and thereby do not support the double-sheath hypothesis.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

A Computational Efficient Space-Vector Modulation Scheme for A Hybrid Seven-Level Converter for Medium Voltage Grid-Tied Applications

In this paper, a fast space-vector modulation (SVM) scheme is proposed for a hybrid 7-level (7-L) converter, i.e., cascaded T-type converter and H-bridge converters, for grid-tied applications. Using oblique coordinate reference, the proposed SVM can quickly locate the switching triangle enclosing the reference vector in the 7-L space vector diagram. Then all available switching sequences and vector duty cycles are acquired by straightforward calculation without using any look-up tables, which significantly reduces the computational cost. The floating capacitor voltages are also stabilized by using the proposed SVM. Experimental studies on a scale-down prototype are presented in this work to validate the effectiveness of the proposed scheme.

Diao, Fei↗
DOE OSTI2021

Efficiency Optimization of Dual Active Bridge Converter Based on dV/dt Snubber Capacitors

This paper presents a lossless regenerative dV/dt snubber circuit for PWM converters to achieve high-efficiency high power-density without significant cost and reliability penalties. The dV/dt snubber employs lossless capacitors for each MOSFET device in a converter to provide an additional path to store the switching energy during turn-off transient and decrease the actual turn-off loss of the MOSFET channel. A novel mathematical turn-off loss model is built to separate the actual turn-off loss of the MOSFET channel and the recycling switching energy stored in the total equivalent output capacitance including Coss, the dV/dt snubber, and etc. Necessary snubber optimization strategy is proposed in order to balance the turn-off loss with ZVS operation range and deadtime conduction loss, and thereby achieving an optimal efficiency performance. To prove the validity and accuracy of the novel turn-off loss model and optimization strategy, the dV/dt snubber has been incorporated into a 1.3kV/200kW DC/DC and a 1kV/70kVA DC/AC PWM converters. Experimental results are given to demonstrate the validity of the proposed dV/dt snubber capacitors and optimization strategy.

Xu, Wei↗
DOE OSTI2021

A Transformer Flux Balancing Scheme Based on Magnetizing Current Harmonic in Dual-Active-Bridge Converters

The Dual-Active-Bridge (DAB) converter transformer flux unbalance, or dc bias, could be a critical issue due to the mismatches of converter circuit parameters and control transients. In this paper, a steady-state flux balancing scheme, based on the second-order harmonic of magnetizing current has been proposed. The relationship between steady-state flux/magnetizing current unbalance and its harmonic contents has been analyzed, with which a new current sensing method and control strategy are introduced. The proposed magnetizing current sensing method can be implemented for both unity and complicated fractional turns ratios, without high sensitivity to dc offset from the analog circuitry. The proposed scheme has been validated with experimental results on 850-V/850-V DAB converters within a system, as well as in an 850-V/6700-V medium voltage DAB unit.

Gao, Zihan↗
DOE OSTI2022

A 20-kW DC Oak Ridge Converter with Integrated AC & DC Sources for Grid Services and Energy Storage Systems

This paper proposes a wireless power transfer (WPT) platform with integrated energy conversion that has the capability for 1) recharging the energy storage systems (ESSs) from the grid systems, including renewable energy sources such as wind, solar, etc., 2) off grid systems recharging the ESSs from dc grid systems, 3) grid recharging of electric vehicles (EVs), and 4) off grid recharging of EVs from ESSs. The unique aspect of the method is the use of multi-interface power electronic converter for the grid and ESSs and EVs that can support a range of applications with ac / dc and dc / dc energy conversion ability in a single converter system. The key enabling technology to achieve these functionalities is Oak Ridge Converter (ORC) with polyphase coupler coil system both developed at ORNL. This new technology enables higher power density WPT systems while allowing the coils to interface from ac grid at 60 Hz frequency or dc source directly merging with 85 kHz operating frequency of switching component. The experimental results of the proposed system are presented for 20 kW output power with the system overall efficiency around 95.4% from dc source and 93% overall efficiency from ac grid achieving 9-10% current total harmonic distortion (THD) and 0.98-0.99 power factor (PF).

Asa, Erdem↗
DOE OSTI2020

Design of 1500V/200kW 99.6% Efficiency Dual Active Bridge Converters Based on 1700V SiC Power MOSFET Module

High efficiency, high density and galvanically isolated power converters are attractive for medium voltage high power applications. This paper presents a 1.5kV/200kW bidirectional Dual Active Bridge (DAB) converter using a newly developed 1.7kV SiC MOSFET module. The intended application is megawatt scale solid state transformer (SST) and 1500V PV inverter application using modular architecture. One novel model to estimate the turn-off loss using snubber capacitors is proposed and experimentally verified. An optimized PCB-based busbar design is introduced to reduce the voltage overshoot across the SiC device, making the design suitable for 1.5kVdc applications. The mechanism of how the optimized PCB-based busbar can reduce the voltage overshoot is quantitatively interpreted and experimentally verified. The DAB converter achieved an efficiency of 98.85% at 200kW and a maximum of 99.53% at 60kW. The maximum efficiency for series-resonant mode is 99.6% at 85kW and 99.3% at 200kW. The power density is 26W/inch3 (1.6MW/m3) which is much higher than traditional industry products.

Xu, Wei↗
DOE OSTI2021

Multiscale Electrothermal Design of a Modular Multilevel Converter for Grid-Tied Applications

As a key feature of modular multilevel converters (MMCs), a large number of semiconductor devices are employed in the converter and distributed over a stack of submodules. Each submodule has a strict temperature limit that imposes constraints on the operating range of the converter. Different loading conditions/losses in the submodules lead to unavoidable temperature variations inside the MMC, which consequently affect the system-level performance and reliability. This paper is focused on the electrothermal analysis and design of a medium-voltage silicon carbide (SiC)-based MMC system, from submodule power semiconductors to the overall MMC system integration of multiple submodules. Loss calculations are performed to estimate the cooling requirements and aid thermal design at different levels. The performance of forced-air cooling approach is analyzed within a numerical modeling framework. Maximum temperature of the SiC power modules is predicted using numerical tools. Thermal design of the MMC cabinet with various arrangement of air inlet(s) and outlet(s) is investigated and compared from a cooling performance perspective.

CFD↗