Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “contact pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Pressure distribution for patchlike contact in seals with frictional heating, thermal expansion, and wear

Sliding contact in seals is known to change at high sliding speed from initially uniform pressure to a deformed state where contact is restricted to small patches of the surface. An earlier analysis of such contact was based upon the assumption of uniform pressure on the small patches. The present study draws upon a thermoelastic influence function to provide simultaneous equations for pressure on subdivisions of the patches. The final result is that at high wear rate (and, consequently, high traversal speed of the patch along the surface of the more conductive body of the contacting pair) the pressure distribution becomes roughly triangular with the maximum pressure toward the leading edge of the patch.

Kilaparti, S. R.↗
DOE OSTI2020

Pressure Drop with Moving Contact Lines and Dynamic Contact Angles in a Hydrophobic Round Minichannel: Visualization via Synchrotron X-ray Imaging and Verification of Experimental Correlations

In hydrophobic mini- and microchannels, slug flow with moving contact lines is typically generated under various two-phase flow conditions. There is a significant pressure drop in this flow pattern with moving contact lines, which is closely related to the dynamic contact angles. Researchers have investigated dynamic contact angles experimentally for decades, but due to the limitations of visualization techniques, these experiments have typically been conducted in low Weber number regions (We < 10 –3 ). In this study, we clearly visualized the dynamic contact angles of a liquid slug in high Weber number regions (10 –3 < We <1) via synchrotron X-ray imaging with high temporal (~1000 fps) and spatial (~ 2 μm/pixel) resolutions. We precisely measured the pressure drop with moving contact lines in a hydrophobic minichannel (inner diameter = 1.018 mm). On the basis of our experimental data, we verified previous correlations for dynamic contact angles and explored the relationship between pressure drop with moving contact lines and dynamic contact angles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2009

One-Dimensional Contact Mode Interdigitated Center of Pressure Sensor (CMIPS)

A one dimensional contact mode interdigitated center of pressure sensor (CMIPS) has been developed. The experimental study demonstrated that the CMIPS has the capability to measure the overall pressure as well as the center of pressure in one dimension, simultaneously. A theoretical model for the CMIPS is established here based on the equivalent circuit of the configuration of the CMIPS as well as the material properties of the sensor. The experimental results match well with theoretical modeling predictions. A system mapped with two or more pieces of the CMIPS can be used to obtain information from the pressure distribution in multi-dimensions.

Xu, Tian-Bing↗
DOE OSTI2024

Tunable amorphous carbon films formed on ultralow wear, Pt–Au alloys

The mechanocatalytic formation of carbonaceous films at the interface between sliding metallic contacts is simultaneously advantageous for reducing friction and adhesion in several tribological applications and detrimental for electrical contacts as they can induce device failure by increasing the contact resistance. Yet, remarkably little is still known about the chemistry, structural and mechanical properties, and tunability of these interfacial layers. In this study, we performed contact pressure-dependent tribological experiments in dry nitrogen containing trace organics on four, nanocrystalline Pt–Au alloys ([Au] from 0 at.% to 10 at.%) – a promising class of alloys for ultralow wear and electrical contact applications. The ex-situ, multi-technique characterization results did not only provide insights into the chemical nature and mechanical behavior of the mechanocatalytic, carbon-rich films formed on Pt–Au surfaces, but also revealed the interplay between catalytic and mechanochemical tribofilm formation controlled by the composition-dependent electronic structure of the Pt–Au substrate and the applied contact pressure. The results of this work provide guidelines for tailoring nanocrystalline alloys to control their mechanocatalytic activity on the basis of variations of the alloy mechanical properties and element's electronic structure with the alloy stoichiometry.

AFM↗
NASA NTRS1974

Lubricant pressure rippling in dynamic Hertzian contacts induced by surface roughness

A numerical analysis of the pressure distribution of a lubricant in contact with a rough surface was conducted. The magnitude of the pressures was determined by their root mean square value for the contact of two dimensional cylinders. The pressure was found to vary in the following manner: (1) the location in the contact, (2) the spectrum or frequency content of the surface roughness, (3) the mean plateau film thickness, and (4) the root mean square value of the surface roughness. Mathematical models are developed to show the relationships of the parameters.

Tallian, T. E.↗
NASA NTRS1997

Frictionless Contact of Multilayered Composite Half Planes Containing Layers With Complex Eigenvalues

A previously developed local-global stiffness matrix methodology for the response of a composite half plane, arbitrarily layered with isotropic, orthotropic or monoclinic plies, to indentation by a rigid parabolic punch is further extended to accommodate the presence of layers with complex eigenvalues (e.g., honeycomb or piezoelectric layers). First, a generalized plane deformation solution for the displacement field in an orthotropic layer or half plane characterized by complex eigenvalues is obtained using Fourier transforms. A local stiffness matrix in the transform domain is subsequently constructed for this class of layers and half planes, which is then assembled into a global stiffness matrix for the entire multilayered half plane by enforcing continuity conditions along the interfaces. Application of the mixed boundary condition on the top surface of the half plane indented by a rigid punch results in an integral equation for the unknown pressure in the contact region. The integral possesses a divergent kernel which is decomposed into Cauchy-type and regular parts using the asymptotic properties of the local stiffness matrix and a relationship between Fourier and finite Hilbert transform of the contact pressure. The solution of the resulting singular integral equation is obtained using a collocation technique based on the properties of orthogonal polynomials developed by Erdogan and Gupta. Examples are presented that illustrate the important influence of low transverse properties of layers with complex eigenvalues, such as those exhibited by honeycomb, on the load versus contact length response and contact pressure distributions for half planes containing typical composite materials.

Zhang, Wang↗
NASA NTRS2000

Helical scan recording with a self-acting negative air bearing

A flat head and a tape transport arrangement impart a wrap angle to the tape at the upstream corner of the head. The wrap angle, corner sharpness and tape stiffness are sufficient to cause a moving tape to form a hollow bump at the upstream corner, thereby creating a hollow into which entrained air can expand, causing a subambient pressure within and downstream of the bump. This pressure keeps the tape in contact with the head. It is created without the need for a groove or complex pressure relief slot(s). No contact pressure arises at the signal exchange site due to media wrap. The highest contact pressures are developed at a wrapped upstream corner. For a tape drive, traveling in both forward and reverse, the wrap can be at both the upstream and downstream (which is the reverse upstream) corners. Heads that are not flat can also be used, if the wrap angle relative to a main surface is sufficient and not too large. The wrapped head can also be used with rotating media, such as disks (floppy and hard) and rotating heads, such as helical wound heads for video recording. Multiple flat tape bearing surfaces can be separated by grooves and/or angles. Each flat can carry heads along one or more gap lines. Multiple adjacent narrow tracks can thus be written for extreme high track density recording.

Muftu , Sinan↗
NASA NTRS1976

Influence of surface roughness and waviness on film thickness and pressure distribution in elastohydrodynamic contacts

The Christensen theory of a stochastic model for hydrodynamic lubrication of rough surfaces was extended to elastohydrodynamic lubrication between two rollers. Solutions for the reduced pressure at the entrance as a function of the ratio of the average nominal film thickness to the rms surface roughness, were obtained numerically. Results were obtained for purely transverse as well as purely longitudinal surface roughness for cases with or without slip. The reduced pressure was shown to decrease slightly by considering longitudinal surface roughness. The same approach was used to study the effect of surface roughness on lubrication between rigid rollers and lubrication of an infinitely wide slider bearing. Using the flow balance concept, the perturbed Reynolds equation, was derived and solved for the perturbed pressure distribution. In addition, Cheng's numerical scheme was modified to incorporate a single two-dimensional elastic asperity on the stationary surface. The perturbed pressures obtained by these three different models were compared.

Chow, L. S. H.↗
NASA NTRS2006

Insulator - Insulator Contact Charging as a Function of Pressure

Metal - metal and metal - insulator contact or triboelectric charging are well known phenomena with good theoretical understanding of the charge exchange mechanism. However, insulator - insulator charging is not as well understood. Theoretical and experimental research has been performed that shows that the surface charge on an insulator after triboelectric charging with another insulator is rapidly dissipated with lowered atmospheric pressure. This pressure discharge is consistent with surface ions being evaporated off the surface once their vapor pressure is attained. A two-phase equilibrium model based on an ideal gas of singly charged ions in equilibrium with a submonolayer adsorbed film was developed to describe the pressure dependence of the surface charge on an insulator. The resulting charge density equation is an electrostatic version of the Langmuir isotherm.

Hogue, Michael D.↗
NASA NTRS1970

Contact material for pressure-sintering ferrites

Pressure-sintering, in which the unfired laminated ferrite plane is placed between two flat punches and pressed during firing, reduces lateral firing shrinkage to less than one percent. A decrease in thickness of the laminate produces the required volume shrinkage. Phlogopite is the most suitable contact material investigated.

Wentworth, C.↗
NASA NTRS1982

Experimental stress analysis of a thin-walled pressurized torus loaded by contact with a plane

It is pointed out that pneumatic tires have a large effect on the overall landing characteristics of an aircraft. The dynamic response upon landing and steering are crucial to the safety of the vehicle and the occupants. The present investigation has the objective to compare experimentally determined strains on an inner tube in contact with a flat plate with numerical values obtained on the basis of a finite element prediction, taking into account an employment of the Structural Analysis of General Shells (STAGS). The obtained results suggest that the clamped boundary condition utilized in the STAGS calculation is not exactly simulated by the employed test setup.

Hill, D. E.↗
DOE OSTI2024

Impact of Pressure-Dependent Interfacial Tension and Contact Angle on Capillary Heterogeneity Trapping of CO2 in Storage Aquifers

Summary Carbon dioxide (CO2) capillary trapping increases the total amount of CO2 that can be effectively immobilized in storage aquifers. This trapping, manifesting itself as accumulated CO2 columns at a continuum scale, is because of capillary threshold effects that occur below low-permeability barriers. Considering that capillary pressure is dictated by heterogeneous pore throat size, the trapped CO2 column height and associated CO2 saturation will vary spatially within a storage aquifer. This variation will be influenced by two pressure-dependent interfacial parameters—CO2/brine interfacial tension (IFT) and CO2/brine/rock contact angle. Our objective is to understand how the pressure dependence of these two parameters affects the heterogeneity of capillary trapped CO2 at a continuum scale. Our conceptual model is a 1D two-zone system with the upper zone being a flow barrier (low permeability) and the lower zone being a flow path (high permeability). The inputs to this model include microfacies-dependent capillary pressure vs. saturation curves and permeability values. The input capillary pressure curves were collected in the literature that represents carbonate microfacies (e.g., dolograinstone) in a prevalent formation in the Permian Basin. We then used the Leverett j-function to scale the capillary pressure curve for the two zones that are assigned with the same or different microfacies. During scaling, we considered the influence of pressure on both the IFT and contact angle of CO2/brine/dolomite systems. We varied the zone permeability contrast ratio from 2 to 50. We then assumed capillary gravity equilibriums and calculated the CO2 saturation buildup corresponding to various trapped CO2 column heights. The CO2 saturation buildup is defined as the CO2 saturation in the lower layer minus that in the upper one. We found that the saturation buildup can be doubled when varying pressure in a storage aquifer, after considering pressure-dependent IFT and contact angles. Thus, assuming these two parameters to be constant across such aquifers would cause large errors in the quantification of capillary trapping of CO2. The whole study demonstrates the importance of considering pressure-dependent interfacial properties in predicting the vertical distribution of capillary trapped CO2. It has important implications in developing a better understanding of leakage risks and consequent storage safety.

Engineering↗