Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conductive ink”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

162 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Power assist EVA glove development

Structural modeling of the EVA glove indicates that flexibility in the metacarpophalangeal (MCP) joint can be improved by selectively lowering the elasticity of the glove fabric. Two strategies are used to accomplish this. One method uses coil springs on the back of the glove to carry the tension in the glove skin due to pressurization. These springs carry the loads normally borne by the glove fabric, but are more easily deformed. An active system was also designed for the same purpose and uses gas filled bladders attached to the back of the EVA glove that change the dimensions of the back of the glove and allow the glove to bend at the MCP joint, thus providing greater flexibility at this joint. A threshold control scheme was devised to control the action of the joint actuators. Input to the controller was provided by thin resistive pressure sensors placed between the hand and the pressurized glove. The pressure sensors consist of a layer of polyester film that has a thin layer of ink screened on the surface. The resistivity of the ink is pressure dependent, so an extremely thin pressure sensor can be fabricated by covering the ink patch with another layer of polyester film and measuring the changing resistance of the ink with a bridge circuit. In order to sense the force between the hand and the glove at the MCP joint, a sensor was placed on the palmar face of the middle finger. The resultant signal was used by the controller to decide whether to fill or exhaust the bladder actuators on the back of the glove. The information from the sensor can also be used to evaluate the effectiveness of a given control scheme or glove design since the magnitude of the measured pressures gives some idea of the torque required to bend a glove finger at the MCP joint. Tests of this actuator, sensor, and control system were conducted in an 57.2 kPa glove box by performing a series of 90 degree finger bends with a glove without an MCP joint assembly, a glove with the coil spring assembly, and with the four fingered actuated glove. The tests of these three glove designs confirm the validity of the model.

Main, John A.↗
DOE OSTI2020

Novel Ionomers and electrode structures for improved PEMFC electrode performance at low PGM loadings (Final Report)

In this project, the objective is to develop new ORR electrocatalysts on optimized supports which can exceed all of the Department of Energy (DOE) 2020 targets listed in DE-FOA-0001412 directly relevant to the subtopic. This project’s approach is to develop novel, electrode-specific ionomers, and integrate them with state-of-the-art NSTF electrocatalyst powder to develop a cathode electrode achieving >= 044 A/mg PGM mass activity, <=30% mass activity loss during metal cycling, and <=0.125 g PGM /kW performance under DOE testing protocols. Ionomer O 2 permeability and proton conductivity will be increased by up to 1.5X over the baseline 3M800 perfluorosulfonate (PFSA) ionomer to enhance cathode electrode performance. Integration of cathode NSTF powder into an ionomer-containing electrode will increase the surface enhancement factor (SEF) to >=40 cm 2 PGM /cm 2 GEO allowing NSTF containing cathodes to exceed DOE MEA robustness targets. This report summarizes this project’s progress towards meeting the stated objectives and includes a summary of significant findings, conclusions, and developments over the entire project period from Oct. 1 st 2016 – Jan. 31 st 2020. This work has overcome key operation robustness issues with classic NSTF electrodes, identified pathways to improved dispersed and dispersed NSTF cathode performance, developed novel ionomers with high bulk conductivity and oxygen permeability, demonstrated exceptional support-independent electrode activity, and significantly increased metal and support stability through ionomer development. At this point, Tufts, MTU and all 5 FCPAD national labs have been involved, and contributed to, the improvements, learning and achievements of this work. Over the course of this project, more than 50 grams of dispersed NSTF powder in 15 different configurations have been generated, paving the way for scaleup within 3M. These whiskers have been processed in multiple ways, including acid leaching, powder-annealed, and sonicated by various means. For Task 2, 27 different types of ionomers were tested, 19 of which were made for the first time during the course of this project. 377 electrode inks with both NSTF and metal-on-carbon catalysts with I/C ratios from 0.2 to 1.2 were generated and mostly coated on a 3M pilot manufacturing line resulting in more than 700 different electrode types.

08 HYDROGEN↗
DOE OSTI2025

Unveiling the Role of In Situ Al 2 O 3 Passivation in Molecular-Ink-Processed CuIn(S,Se) 2 Photovoltaics

Here, we report on the optimization of in situ passivation of ink-based CuIn(S,Se) 2 thin-film solar cells via controlled incorporation of Al 2 O 3 in CuIn(S,Se) 2 films by the addition of Al(NO 3 ) 3 to the molecular ink precursor. For this purpose, the Al/(Al + In) (AAI) metal ratio was varied from 0.05 to 0.30. We observe that the efficiency of the cells made of Al 2 O 3 -incorporated CuIn(S,Se) 2 is consistently higher than those without Al 2 O 3 , especially due to an improvement in open-circuit voltage (V OC ) and fill factor (FF), for all tested AAI ratios. With an AAI of 0.05, a maximum efficiency of 11.2% and an average efficiency of 8.5% (measured across 18 cells) was achieved, compared to 8.5% maximum efficiency and 6.5% average efficiency for Al-free CuIn(S,Se) 2 . Furthermore, we find that cells made of Al 2 O 3 -incorporated CuIn(S,Se) 2 with an AAI of 0.2 show a narrow distribution in the photovoltaic performance, indicating higher reproducibility and higher FF. Energy-dispersive X-ray spectroscopy shows that, at AAI = 0.2, Al 2 O 3 is distributed more homogeneously at the surface of the Al 2 O 3 -incorporated CISSe. Capacitance-voltage measurements reveal a reduced defect density by incorporation of Al 2 O 3 , which could be partly responsible for the higher V OC . Furthermore, using detailed surface analysis with various X-ray and electron spectroscopy methods, we derive chemical and electronic structure information from the surface. With ultraviolet photoelectron (UPS) and inverse photoemission spectroscopies (IPES), the electronic band gap of the CuIn(S,Se) 2 thin-film surface is found to increase from 1.22 to 1.88 eV (+-0.12 eV) with Al 2 O 3 incorporation. This is accompanied by a clear reduction of the conduction band spike at the CdS/CISSe interface due to Al 2 O 3 addition, as derived by both UPS and IPES as well as temperature-dependent V OC measurements.

14 SOLAR ENERGY↗
DOE OSTI2022

Performance of Lithium-Ion Batteries with 3D Printed Anodes and Compressible Carbon Structures

Carbon scaffolds have been shown to improve the performance of Li metal anodes in Li-ion batteries by acting as conductive hosts for Li metal plating and stripping. The scaffolds provide a more uniform electric field, and their 3D geometry enables smaller diffusion paths for the Li ions. In this project, several different types of carbon lattices were 3D printed, mechanically tested, and analyzed in coin cells. Planar and 3D printed graphite coatings were evaluated as the baseline, since graphite is a common anode material. The results showed that implementing a 3D graphite lattice into a coin cell improved the Li plating and stripping efficiency compared to the planar coating. However, since graphite can intercalate Li ions, other carbon materials were also explored that should act as better hosts for Li plating/stripping. To improve the compressibility of these non-graphite carbon scaffolds, five different carbon ink formulations were 3D printed in lattice configurations. SEM imaging and compression testing showed that both the final dimensions and the compressibility of the carbon lattices depended on the type of carbon precursors used. The two most suitable compositions were found to be those made with graphene oxide-resorcinol formaldehyde and graphene oxide-ammonium hydroxide. In the future, these formulations will be further refined to increase their mechanical strength, and their performance as scaffold hosts for Li metal anodes will be evaluated in coin cells.

25 ENERGY STORAGE↗
DOE OSTI2025

Toward Fullerene-Free PIN Perovskite Solar Cells

We highlight opportunities for a transformative shift in perovskite solar cell design by expanding electron transport layers (ETLs) beyond fullerenes. Fullerenes have known limitations, including constraints on open-circuit voltage, stability, and mechanical integrity. Recently, fullerene-free p-i-n cells with power conversion efficiencies exceeding 25% have been demonstrated via both naphthalene diimide-SnO x bilayers and nonfullerene acceptor-based ETLs. Despite successes, fullerenes remain the de facto ETLs for perovskites. Drawing lessons from organic photovoltaics, where it took decades to transition from fullerenes to more broadly available and efficient materials, we explore pathways to accelerate the development and adoption of fullerene-free ETLs. This requires understanding the similarities and differences between organic and perovskite solar cells, which will necessitate carefully designing fullerene replacements with both, high efficiency and also, critically, durability under operation. Here, we incorporate literature data to facilitate comparisons, and independently conduct fracture energy measurements for alternative ETL configurations to motivate their adoption.

14 SOLAR ENERGY↗
NASA NTRSDate not supplied

Print-Consistency and Process-Interaction for Inkjet-Printed Copper on Flexible Substrate

Printed electronics is a fastest growing and emerging technology that have shown much potential in several industries including automotive, wearables, healthcare, and aerospace. Its applications can be found not only in flexible but also in large area electronics. The technology provides an effective and convenient method to additively deposit conductive and insulating materials on any type of substrate. Comparing with traditional manufacturing processes, which involves chemical etching, this technology also comes to be relatively environmental friendly. Despite its status, it is not without its challenges. Starting from the material being compatible in the printer equipment to the point of achieving fine resolutions, and with excellent properties are some of the challenges that printed electronics face. Among the myriad of printing technologies such as Aerosol Jet, micro-dispensing, gravure printing, screen printing, Inkjet printing, Inkjet has gained much attention due to its low-cost, low material consumption, and roll-to-roll capability for mass manufacturing. The technology has been widely used in home and office, but recently gained interest in printed electronics in a research and development setting. Conductive materials used in Inkjet printing generally comprises of metal Nanoparticles that need to be thermally sintered for it to be conductive. The preferred metal of choice has been mostly silver due to its excellent electrical properties and ease in sintering. However, silver comes to be expensive than its counterpart copper. Since copper is prone to oxidation, much focus has been given towards photonic sintering that involves sudden burst of pulsed light at certain energy to sinter the copper Nanoparticles. With this technique, only the printed material gets sintered in a matter of seconds without having a great impact on its substrate, due to which it is also preferred in low temperature applications. With all the knowledge, there is still a large gap in the process side with copper where it is important to look how the print process affects the resolution of the print along with the effect of post-print processes on electrical and mechanical properties. In this paper, a copper Inkjet ink is utilized for understanding the effect of Inkjet print parameters on the ejected droplet and its resolution. Post-print process is also quantified using a photonic sintering equipment for excellent electrical and mechanical properties. To demonstrate the complete process, commercial-off-the-shelf components will also be mounted on the additively printed pads via Inkjet. Statistically, control charting technique will be utilized to understand the capability of the Inkjet process.

printed electronics↗
DOE OSTI2026

Solution-Processed Oxide Thin Films for Perovskite Photovoltaics (Final Report)

The overarching goal of the voucher project is to evaluate the suitability of NexTC materials as functional layers in perovskite photovoltaic technology. There are several different perovskite device configurations that are being pursued for commercialization. Most are superstrate configuration (light enters the device through the glass substrate) and can be subdivided into two categories: PIN and NIP. At minimum, PIN devices have a transparent conductor (typically Indium Tin Dioxide [ITO] or Fluorine-Doped Tin Oxide [FTO]) and hole transport layer (HTL) deposited on glass before the perovskite is deposited. Alternatively, NIP devices have a transparent conductor and electron transport layer (ETL) deposited before the perovskite is deposited. NexTC produces several inks that can be deposited to replace or modify the transparent conductor and/or the ETL or HTL, depending on the device. NLR will produce PIN and NIP perovskite devices on substrates that have been coated by NexTC and compare to NLR-standard devices that perform among the best for research labs across the world. The work will ultimately expose NexTC products to the up-and-coming perovskite PV industry.

14 SOLAR ENERGY↗
DOE OSTI2022

Carbon Electrodes from Powder River Basin Coal Development of Competitive Supercapacitor Electrodes of Diverse Compositions from Coal Extract

Recent demand for coal as a thermal energy source has decreased significantly and will likely continue to decrease as renewable sources of energy become more available and environmental concern and cost from burning coal makes it more costly than renewables. Given that Powder River Basin (PRB) coal in Wyoming has relatively low thermal energy, it is critical for Wyoming to employ coal in other capacities at the current energy transition period in history. Among many potential non-thermal applications, PRB coal can be utilized for membrane and electrode applications through the formation of carbon fibers. Coal-derived membranes can become low-cost, conductive membranes for use in electrodialysis separation processes. Carbon fiber derived electrodes have been shown be a cost-effective alternative to typical electrode materials that can meet or exceed the performance of current carbon electrode materials. In this talk, we demonstrate the manufacture of supercapacitor electrodes from Powder River Basin (PRB) coal-derived precursors. Specifically, PRB coal was treated in cheap solvents, partitioned into liquid extract and solid residue. An electropinning process has been developed that can convert either the liquid extract or the solid residue into carbon fiber mats. The electrospinning process is versatile with many tunable process parameters to achieve desirable physiochemical properties. For example, the coal residue can be manipulated by additional heat treatment, or by adding binders, salts, or surfactants to create a solution that can be electrospun into advanced carbon electrodes with desirable structural and surface properties. Similarly, some of the liquid extract (tar fraction) can be subsequently reacted with toluene diisocyanate to create resinous coal-derived polyurethane (PUs) as a spinnable ink. Carbon nanofiber mats made from our proprietary electrospinning process were further carbonized at temperature ranging from 700°C to 900°C before they are used as electrodes in supercapacitors. Galvanostatic charge-discharge (GCD) results show that the best performing PU fiber mats can deliver a specific capacitance of 604 F g -1 at the current density of 1 A g -1 . A carbon fiber mat from a different solvent extraction residue also delivered the specific capacitance of 508 F g -1 . These specific capacitance values are comparable to or better than commercial activated carbons, demonstrating the viability of manufacturing carbon nanofiber electrodes from coal without the use of a commercial polymer as binder in the spinning ink.

Cincotta, Robert↗
DOE OSTI2022

3D Printed Carbon Aerogels for Polymer-Electrolyte Fuel Cells

Carbon aerogels (CA) are known for ultra-low density, very high surface area, fine porous structure, and excellent electrical conductivity. Recent advances in high resolution 3D printing at LLNL enable the manufacturing of complex structured CA electrodes which have been demonstrated in electrolysis, flow battery, and supercapacitor applications. Polymer-electrolyte fuel cells (PEFC) may be an excellent candidate for these materials/methods as designers seek to optimize membrane-electrode assemblies to achieve higher efficiencies. A major challenge to PEFC design is two-phase flow due to water production which causes pore flooding and leads to cell instability and degradation. To mitigate these effects, groups have investigated the creation of liquid specific pathways in the porous layers to alleviate liquid buildup and enhance gas diffusion. While some progress has been made, traditionally manufactured GDLs, which consist of randomly distributed carbon fibers, are limiting. 3D printed CAs are a promising solution as complex macroporous electrode structures can be manufactured out of micro and nano porous filaments with a high level of control. Additionally, the process may allow for the consolidation of multiple layers (MPL, GDL, & flow channels) into a single printed architecture. In this work various CA lattice structures were printed using a direct ink write (DIW) method and liquid breakthrough pressures were measured to demonstrate the ability to tune the water pathways to achieve specific pressure thresholds. Furthermore, a discussion of the prospects for printed CA electrodes in PEFC will focus on material properties, synthesis techniques, and current challenges.

36 MATERIALS SCIENCE↗
DOE OSTI2025

15-minute Parker River gap-filled tide height and salinity data, PIE LTER, Plum Island Sound, MA (2014–2023), for ELM PFLOTRAN modeling

This dataset contains 15-minute tide height and salinity data from the Typha site along the Parker River, part of the Plum Island Ecosystems Long Term Ecological Research (PIE LTER) site in Plum Island Sound, Massachusetts (MA) 2014-2023. Tide height (in NAVD88) was compiled from measurements conducted at the mouth of Plum Island Sound and corrected for time lags. Gap-filling of missing periods were done by fitting tidal constituents to the time series. Salinity was measured (and is stored on ESS DIVE ) in 2022 and 2023 using HOBO U24-002 conductivity loggers. River discharge is the most important control on tidal river water salinity at the location (Vallino & Hopkinson, 1998). An artificial neural network was trained to predict river water salinity at the location using Parker River discharge (USGS station 01101000, Parker River at Byfield, MA) and gap-filled salinity observations from a long-term monitoring station ca. 3km downstream from the Typha site (LTER station ‘Middle Road’) as input variables to create continuous time series information. The data set was used in the spin up and simulations of a land surface model coupled to a biogeochemical reaction network (ELM PFLOTRAN) assessing impacts of hydrology and salinity input on methane fluxes in 2022 and 2023 (Sulman et al., 2024). Metadata files ELMPFLOTRAN_tide_salinity_dd.csv and ELMPFLOTRAN_tide_salinity_flmd.csv provide details on site location, data variables, and QA/QC methods .

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Meso-Structured Polymer Electrolyte Fuel Cell Electrode

Increasing the utilization of Pt and Pt alloy catalysts in polymer electrolyte fuel cell cathodes is critical to improving the high power density operation, particularly at low Pt loadings. State of the art electrodes are fabricated in an ink deposition process that leads to uncontrolled electrode architecture with random aggregates of functional domains (catalyst, ionomer, and pore volume) (1). The randomness in the domains induces high tortuosity transport pathways for ions and fluids, which cause severe transport resistance during high current density operation. Thin ionomer films cause additional transport resistance and poisoning of the Pt catalyst, which becomes more significant at low Pt loadings. Reducing the amount of ionomer in the catalyst domain without affecting the ionic transport resistance is key to improving the utilization of the Pt and reducing the transport resistance at low Pt loading. Rational design of the electrode structure with controlled low tortuous ionic transport pathways could improve performance. The introduction of the ionomer pathways could also enable reduction of the ionomer volume in the catalyst domain, reducing the transport resistance. Middelmen et al. proposed electrode structures consisting of aligned components in a low tortuosity configuration to improve performance (2). In this work, we present an alternative electrode structure based on a vertically aligned array of Nafion pillars in the cathode catalyst layer, as shown in Figure 1a. Figure 1b shows the SEM image of the Nafion pillars. Furthermore, Pt supported on carbon catalyst was deposited on the Nafion pillars to fabricate a meso-structured electrode. Nafion pillars provide high conductive and low tortuous pathways for protons, reducing the effective transport distance, and enabling reduction of the ionomer binder in the catalyst domain.

25 ENERGY STORAGE↗
DOE OSTI2025

Data for Machado-Silva et al. (2024), "Short-Term Groundwater Level Fluctuations Drive Subsurface Redox Variability"

This dataset contains the analytical data reported in Machado-Silva et al. (2024) as part of the COMPASS-FME project, which seeks to advance a scalable, predictive understanding of the fundamental biogeochemical processes, ecological structure, and ecosystem dynamics that distinguish coastal terrestrial-aquatic interfaces from the purely terrestrial or aquatic systems to which they are coupled. The dataset consists of water quality parameters as well as redox potential, water content, and electrical conductivity. These data were collected in 2022 in Crane Creek (CRC), Portage River (PTR), and Old Woman Creek (OWC). Each of these sites included uplands (UP), transitions (TR), wetland-transition edge (WTE), and wetland (W) zones. The sites represent replicates of the Lake Erie terrestrial-aquatic interface under fluctuating water levels and are located in well-preserved areas with natural or restored marsh and forest cover.This dataset consists of a single data file (Machado_Silva_et_al_2024_EST_data.csv) that is in comma-separated value (CSV) format. No special software is required to read it.This dataset uses the ESS-DIVE Hydrologic Monitoring Reporting Format 1.0.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

AOI [1]: Passive Wireless Sensor Systems Fabricated by Direct-Writing for Temperature and Health Monitoring of Energy Systems in Harsh-Environments (Final Report)

Researchers at West Virginia University (WVU) propose to demonstrate a wireless, high-temperature sensor system for monitoring the temperature and health of energy-system components. The active sensor and electronics for wireless communication will be composed entirely of an electroceramic materials (conductive ceramics) which are capable of withstanding the harsh-environments required for fossil energy-based technologies. This work will focus primarily on the fabrication and testing of temperature (thermocouples and thermistors) and health (strain/stress and crack propagation sensors) that function at extreme temperatures (up to 700-1700ºC). The electronics will accompany the high-temperature sensor, which will include a passive wireless communication circuit that allows the transmission of the data based on the LCR resonance principle to a near-by reader antenna. This passive transmission of data will reduce the need for interconnect wires near the active, and possibly rotating, energy-system component. The research will include process development to permit the 2D/3D direct-writing of the entire sensor and communication circuit onto the energy-system component. The direct-writing will be facilitated by using silicon-based polymer-derived precursors to form the high-temperature, stable electroceramic compositions. In addition, methods for direct-writing the circuit onto a fugitive carrier substrate will be completed, which will permit a “peel-and-stick”-like transfer of the sensor circuit to the energy-system component. This feature will allow the economical and precise placement of the sensor circuit onto components of various shapes and locations, without altering the geometry and active features of the manufactured component, or the removal (or decommissioning) of the component for installation. The proposed work will be directed at the following areas: 1) Investigation of phase formation, sintering/grain growth, and electrical properties of polymer-derived electroceramic composites; 2) Definition of processes to direct-write through ink-jet and robo-casting the polymer-derived electroceramic composites onto oxide and polymer surfaces; 3) Development of methods to form monolithic "peel-and-stick" preforms that will efficiently transfer the sensor circuit to ceramic surfaces after thermal treatment; 4) Design of passive wireless LCR circuits and receiver (reader) antennas for communication and testing at high temperatures; 5) Investigation of the passive wireless sensor system developed (and method of transferring sensor system) for temperature and stress/strain measurements on a SOFC repeat unit and a singular gas turbine blade prototype as example applications.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

ELM model simulations of Plum Island Ecosystems LTER low marsh site 2018-2020

Model simulations using the Department of Energy's Energy Exascale Earth System Model (E3SM) land model (ELM) with improved capabilities to represent vegetation response to salinity and inundation. The simulations were conducted for a tidal salt marsh at Plum Island Ecosystems Long Term Ecological Research (LTER) site near Rowley, Massachusetts, USA; the site is a low marsh dominated by Spartina alterniflora. The model was forced with site-specific meteorology, salinity and tidal cycles from 2018-2020. Four sets of model simulations are included and described below:1. Parameterization of the salinity response function. These simulations tested different combinations of values for optimal salinity and salinity tolerance.2. Model evaluation. This comparison conducted simulations using the default model, the salinity function only, the submergence function only, and both the salinity and submergence functions. 3. Salinity scenarios. These simulations used the 2018 salinity input data varied by -5 to +10 ppt salinity.4. Water level scenarios. These simulations used the tide height varied by -10 to +50 cm. These simulations were used to demonstrate how the salinity and submergence functions better represent carbon uptake by tidal salt marshes.The data package includes netCDF files used as forcing files for tide height and salinity, one for each year 2018-2020 at observed salinity concentrations, and an additional three forcing files in which salinity concentrations were varied 5 ppt lower, 5 ppt higher, and 10 ppt higher than the measured 2018 time series. Also included are python scripts for creating forcing files, plain text parameter and command files for running simulations, model outputs in netCDF format, and python scripts for visualizing outputs. Code for the modified E3SM model is archived in Sulman et al 2023 at doi:10.15485/1991625. More detail about files is provided in the README.md file.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Rising Water Levels and Vegetation Shifts Drive Substantial Reductions in Methane Emissions and Carbon Dioxide Uptake in a Great Lakes Coastal Freshwater Wetland

ABSTRACT Coastal freshwater wetlands are critical ecosystems for both local and global carbon cycles, sequestering substantial carbon while also emitting methane (CH 4 ) due to anoxic conditions. Estuarine freshwater wetlands face unique challenges from fluctuating water levels, which influence water quality, vegetation, and carbon cycling. However, the response of CH 4 fluxes and their drivers to altered hydrology and vegetation remains unclear, hindering mechanistic modeling. To address these knowledge gaps, we studied an estuarine freshwater wetland in the Great Lakes region, where rising water levels led to a vegetation shift from emergent Typha dominance in 2015–2016 to floating‐leaved species in 2020–2022. Using eddy covariance flux measurements during the peak growing season (June–September) of both periods, we observed a 60% decrease in CH 4 emissions, from 81 ± 4 g C m −2 in 2015–2016 to 31 ± 3 g C m −2 in 2020–2022. This decline was driven by two main factors: (1) higher water levels, which suppressed ebullitive fluxes via increased hydrostatic pressure and extended CH 4 residence time, enhancing oxidation potential in the water column; and (2) reduced CH 4 conductance through plants. Net carbon dioxide (CO 2 ) uptake decreased by 90%, from −267 ± 26 g C m −2 in 2015–2016 to −27 ± 49 g C m −2 in 2020–2022. Additionally, diel CH 4 flux patterns shifted, with a distinct morning peak observed in 2015–2016 but absent in 2020–2022, suggesting changes in plant‐mediated transport and a potential decoupling from photosynthesis. The dominant factors influencing CH 4 fluxes shifted from water temperature and gross primary productivity in 2015–2016 to atmospheric pressure in 2020–2022, suggesting an increased role of ebullition as a primary transport pathway. Our results demonstrate that changes in water levels and vegetation can substantially alter CH 4 and CO 2 fluxes in coastal freshwater wetlands, underscoring the critical role of hydrological shifts in driving carbon dynamics in these ecosystems.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Dataset for scientific paper "Simulated plant‑mediated oxygen input has strong impacts on fine‑scale porewater biogeochemistry and weak impacts on integrated methane fluxes in coastal wetlands", a modeling study based on field observation at the tidal salt marshes of the Parker River Estuary, Massachusetts, United States

This dataset is the raw and processed data for the paper "Simulated plant ‑ mediated oxygen input has strong impacts on fine ‑ scale porewater biogeochemistry and weak impacts on integrated methane fluxes in coastal wetlands". This study investigated how plant-mediated oxygen input affects subsurface biogeochemical reactions of organic carbon degradation and the resulting methane emissions of coastal wetlands by model simulation. We used the subsurface geochemical simulator PFLOTRAN for the modeling, which produced the simulated changes in porewater chemical substances and methane emissions over 10 days under different scenarios of plant-mediated oxygen input.Specifically, this dataset contains: 1) the input files for PFLOTRAN of all simulation runs conducted in this study. Those files are with an extension of ".in", containing information of the biogeochemical reaction network (stoichiometry, reaction rate, Monod constants, etc), fluid flow rate and oxygen concentration in the fluid which together simulated the plant-mediated oxygen input, the configuration of artificial reactions that simulated the methane fluxes, etc. The PFLOTRAN input files are text files, which can be opened by NotePad, but running these input files will require proper installation of PFLOTRAN (instruction: https://documentation.pflotran.org/user_guide/how_to/installation/installation.html). 2) the raw and processed model output from PFLOTRAN of all simulation runs, and 3) the python scripts used to process the raw model output, including random allocation of root cells, converting raw data into organized formats, calculating the methane fluxes based on the model output, data visualization, etc. The raw and processed model output from PFLOTRAN are in .spydata format, which can be viewed with Python. and 3) the python scripts for data processing and analysis are programming scripts, which can be opened with Python.This modeling work, in particular the model parameterization of root density and initial conditions of porewater concentrations of biogeochemical substances, was based on field measurements at the salt marsh of the Upper Parker River Estuary, Massachusetts, United States.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Model simulations of Plum Island Ecosystems LTER low marsh site using ELM-PFLOTRAN

Model simulations using the E3SM Land Model (ELM) coupled to the PFLOTRAN reactive transport model via the Alquimia interface. The simulations were conducted for a tidal salt marsh at the Plum Island Ecosystems LTER near Rowley, Massachusetts, USA. Model simulations were forced using site-specific tidal cycles and salinity, and the simulations used a biogeochemical reaction network including aerobic decomposition, sulfate reduction, iron reduction, and methanogenesis. Model outputs include simulated carbon stocks, carbon dioxide and methane fluxes, and porewater concentrations of key solutes related to sulfur, iron, and carbon cycling. The model simulations included a saline simulation (with tidal sulfate inputs), a fresh simulation (with low salinity and low sulfate inputs), and a saline simulation with lower vegetation productivity to represent the effect of salinity on vegetation. These simulations were conducted to demonstrate that a new model framework incorporating subsurface redox and biogeochemical interactions into a land surface model could reproduce measured surface greenhouse gas fluxes and biogeochemical dynamics in tidal marsh ecosystems, and to test whether including redox interactions in a land surface model would allow the model to resolve contrasts in biogeochemical cycling and greenhouse gas production between saline and freshwater wetlands.The data package includes gzipped tar archives (which can be expanded using standard tar and gzip utilities) of model outputs from three model configurations: saline subsurface and reduced vegetation productivity related to salinity; saline subsurface with vegetation productivity not reduced; and freshwater. Also included are code for the modified E3SM model, Alquimia interface, and PFLOTRAN reactive transport simulator in gzipped tar format; plain text parameter and configuration files; python code files for visualizing model output and defining model configurations; and model output, tide and salinity forcing, and configuration files in netCDF format. See the README.md file in the data package for a detailed description of all files contained in the package. All files are in netCDF (.nc), gzipped tar archive (.tar.gz or .tgz), or text (all other files).Updated: May 13, 2024. Model output, E3SM code, PFLOTRAN input files, and python codes for visualizing results were updated to reflect changes made for the manuscript revision. The updated archive reflects the code and model output from the final accepted manuscript. Changes included updated reaction parameters reflecting improved parameterization and additional comparisons with field measurements. E3SM code changes included better support for multiple grid cells and improved flow and transport parameterization.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Laboratory-Scale Coal-Derived Graphene Process (Final Report)

The Energy & Environmental Research Center (EERC) conducted a laboratory-scale coal-derived graphene (CDG) project focused on developing a technological process for making graphene from four U.S. domestic coal or coal wastes, including lignite from North Dakota, subbituminous coal from Wyoming, bituminous coal from Utah, and anthracite from Pennsylvania. The project was divided into two performance or budget periods (BPs), with BP1 comprising the up-front laboratory experiments to make graphene materials from coal beginning on May 1, 2020, to April 30, 2022. BP2 was conducted from May 1, 2022, to April 30, 2023, and was focused on analyzing the CDG process economic feasibility and the technical gaps for technological scale-up and commercialization. During this project, a few different coal-derived high-value products have been demonstrated, including graphite, graphene oxide (GO), reduced graphene oxide (rGO), and graphene quantum dots (GQDs). A new graphite microstructure was discovered and named “croissant graphite” because of the exterior morphological and textural resemblance to croissant food items sold in commercial groceries stores. The new graphite structure and the associated preparation from coal or coal waste feedstocks has been the subject of a U.S. patent application. The systematic experimental processes involving coal cleaning, upgrading, and conversion to high-value carbon products culminated into a developed upgraded coal-to-products (UCP) technology that is being pursued for potential fast-track commercialization, if funding is available. It is envisioned that commercialization of the UCP technology would increase consumption of U.S. domestic coals or coal wastes to make environmentally sustainable high-value products for the electronics industry, high-energy-storage applications, and clean energy technologies such as electric vehicle (EV) lithium-ion batteries (LIBs), for which graphite has become a critical mineral commodity. Croissant graphite microstructures, when observed by field emission scanning electron microscopy (FESEM), display wavy surface morphology and often grow from a base that is made of graphitized particles with honeycomb-like layers, which are believed to be graphene layers. While more studies are needed to fully ascertain the mechanisms of the croissant graphite microstructure formation, it is postulated that their growth may begin from curling of the graphene sheets into ribbon-like structures, and continuous growth and densification of the ribbon-like structures forms croissant microstructures. Additional studies are ongoing to evaluate the electrochemical performance of croissant graphite for LIB applications and to determine the experimental conditions necessary to tune on/off croissant formation so that it can be either optimized or suppressed depending on performance evaluation results. In addition to the discovery of croissant graphite, the graphitization process from the four coal ranks in general was successful. X-ray diffraction (XRD) analysis showed that the degree of graphitization (DoG) ranged from 12% to 80% in an early sample set, and further optimization on lignite coal produces a DoG of about 92%, which was spectacular to see as lignite is the lowest-rank coal. Thus, it is expected that the graphitization performance for higher-rank coals will be similar or better when optimized as well. The coal-derived graphite was used to make GO and rGO. Analytical characterization, e.g., by methods such as Raman spectroscopy, XRD, Fourier transform infrared (FTIR) spectroscopy and FESEM, showed that the sequence of converting the coal to graphite, exfoliating it to GO, and then chemically reducing the GO to rGO was successful. Although coal naturally contains aromatic compounds and some relatively small-sized condensed aromatic units, it does not contain graphene sheets. In the UCP process, the aromatic domains in the coals, particularly low-rank coals, are concentrated and condensed further into graphene sheets, which are ordered into a 3D stack during graphitization. The synthesized graphite is then unpacked by methods such as exfoliation to various graphene products. GQDs were synthesized from all four coal types, and their optical properties were demonstrated to be tunable by the coal precursor preprocessing treatments. In all four coal types, enhanced optical properties were observed for the produced GDQs with incremental improvements made to the coal precursors. GQDs produced from raw coal samples displayed lower ultraviolet–visible (UV–Vis) spectroscopy absorbance intensity compared to those obtained from cleaned and upgraded coal residues. The photoluminescence (PL) intensities also varied with pretreatment conditions and with the concentration of GQDs in aqueous solutions. GQDs obtained from anthracite show longer emission wavelengths and can be excited by visible light as opposed to GQDs derived from the other coal ranks. UV fluorescence 3D maps and spectra revealed that the emission wavelength at which the GQDs solutions display the highest intensity was slightly redshifted based on the coal precursor pretreatments. In low-rank coal (lignite and subbituminous) samples, two clusters were observed in the maps for GQDs, which may suggest that there are potentially two types of fluorophores in solution or two main size populations. The ability to tune the properties of GQDs based on processing methods can be exploited to make GQDs for various optical display or optoelectronics applications. The results also highlight the importance of removing coal-borne impurities to improve the quality of the coal precursor for preparation of graphene products. Coal and/or coal wastes preprocessing methods were developed and applied to clean and upgrade the coal precursors prior to graphitization and subsequent conversion to graphene products. The preprocessing methods involve high specific-gravity separations, mineral acid cleaning (no hydrofluoric acid), and subsequent upgrading by reducing the coal-borne heteroatom (nitrogen, sulfur, and oxygen) content using proprietary chemical agents. Analytical characterization revealed that the preprocessing steps were successful, with ash reductions that range from 38% to 80% and residual ash content that was below the 5 wt% initial target. Based on proximate and ultimate analysis, the heteroatom reduction reactions produced upgraded coal residues with the oxygen content reduced by 8% to 24%, with additional reductions in the nitrogen and sulfur contents. An initial assessment of the waste streams from the UCP process shows very small to negligible environmental impact due to CO 2 , NO x , and SO x because most process steps are performed under inert atmosphere with argon. Consequently, reactive oxygen environments that tend to create these species are avoided. The inorganic and potentially hazardous species are released into aqueous waste streams that are easy to handle for proper disposal. The liquid waste streams were found to contain low-level concentrations of rare-earth elements (REEs), which could be concentrated and recovered as value-added by-products. Additionally, the volatile and gaseous fractions from carbonization and heat treatment contain useful organic compounds that can also be recovered as potential valuable by-products. Thus, the UCP technology is considered an environmentally sustainable and promising emerging technology for making high-value products from coal and coal wastes, with potential additional value-added by-products. Analysis of potential markets for the coal-derived carbon products shows a strong demand in both niche market sectors and across a wide variety of other industrial sectors. Graphite is currently considered a critical mineral commodity that has a large and growing demand in the LIB industry for EV applications. Based on data from Fortune Business Insights (2022) and Marketwatch (2023) reports, the average global graphite market is projected to reach about 33 billion by 2028, growing at a compound annual growth rate (CAGR) of about 7%, with much of this growth expected to be in the LIB industry. GO and rGO have strong market potentials in various application areas, such as coatings for anticorrosion, anti-icing, and antimicrobial protection, thermal barriers, wear resistance, sensors, additive manufacturing such as 3D inks, and others. GQDs are the emerging key player in the bioimaging, photovoltaics, and light-emitting diodes (LEDs) applications, with the potential to replace traditional semiconductor quantum dots (SQDs), which are based on metallic systems that are more toxic and more expensive. Biomedical applications of GQDs are becoming more attractive because of low to no toxicity and extremely low cost compared to SQDs. The major challenges for scale-up and commercialization of coal-derived carbon products such as graphene vary from the inherent attributes of graphene itself to reluctance to accept graphene in new manufacturing processes because of the uncertainty of the unknown. The 2D nature of graphene materials with a thickness of one atom presents significant challenges to proper handling/processing, and process scale-up becomes difficult because it requires high-end, expensive equipment, even for routine handling and analysis for quality assurance and control. Pristine graphene can also be extremely difficult to work into other matrices, thus hindering downstream processibility, especially at large scale. Currently, the cost of graphene and graphene products is still high and presents an economic risk that tends to slow down investment in scaling up emerging technologies. The lack of a standard for graphene materials for quality assurance and quality control poses a great challenge not only for the markets but also for commercialization efforts. A first-look economic feasibility analysis of the UCP technology provided valuable information that suggests the UCP process would be feasible, especially when it is scaled to a pilot scale and could be more competitive at the full scale. Graphitization was found to be the most energy-consuming and most capital-intensive step in the overall process. In small laboratory- and bench-scale experiments, labor is a significant contributor to the total process costs. Although these energy, capital, and labor constraints contribute to a higher selling price for the product, a preliminary economic model suggests that the process would be feasible at large scale when the process is fully integrated, optimized, and automated.

01 COAL, LIGNITE, AND PEAT↗