Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “complex oxide interfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Impact of metal diffusion, lattice distortions, native defects, and ambient on dielectric breakdown in Ni–Ga 2 O 3 Schottky diodes

Ga 2 O 3 unipolar devices are of high interest due to their ~8 MV/cm predicted breakdown fields, which have not yet been achieved due to premature device failure. Pre- and post-failure defect analysis of Ni–Ga 2 O 3 Schottky diodes in ultrahigh vacuum (UHV) and air were performed using depth-resolved cathodoluminescence, high angle annular dark field scanning transmission electron microscopy, and energy dispersive x-ray analysis to understand the physical mechanisms that precede premature breakdown. The breakdown voltage in UHV was dramatically reduced by nearly 40% compared with the breakdown in air. This reduction in the breakdown voltage correlated with post-breakdown differences in Ni distribution, indicating that the coordination and bonding of Ni contribute strongly to electrical behavior in Ni–Ga 2 O 3 Schottky diodes. Breakdown studies in UHV revealed that Ni diffuses away more from the metal–semiconductor interface than with air breakdown, where Ni localizes more near the interface, indicative of the preferential formation of a Ni oxide under O-poor conditions. These measurements also identified the formation of divacancy-interstitial complexes and their characteristic luminescence signature ~150 nm from the interface, the densities of which correlated with breakdown fields. These findings show that electric-field-induced degradation occurs via the rearrangement of native point defects, which act as an additional precursor to device failure. Macroscopically, they show the impact of both vacuum conditions and metal reactivity on Ga 2 O 3 device fabrication.

36 MATERIALS SCIENCE↗

Controlled Generation of TiO x –Au Interface Using Titanium Molecular Complex Bearing Pyridyl Anchors: Synthesis, Characterization and Catalysis

Interfacial perimeter sites between metal and support are often important for catalysis. A mononuclear titanium siloxy complex III, Ti(acac) 2 [OSiC 6 H 5 N(OCH 3 ) 2 ] 2 was synthesized to generate TiOx units of different degrees of clustering to decorate Au nanoparticles. Two different methods of preparation were examined; one was to deposit III onto Au/SiO 2 and the other was to form III-covered Au nanoparticle first before deposition onto SiO 2 . The former method generated more highly dispersed TiO x units, while larger domains of TiO 2 were formed with the latter method, as deduced by UV–vis and XAS characterization. A model was proposed to explain how TiO x dispersity could be related to the preparative procedures. These samples were further tested as catalysts in selective oxidation of propane in a stream of O 2 and H 2 . They exhibited different product selectivities. The sample with more dispersed TiO x units were more selective for acetone formation versus propene formation. The results confirmed the important role of both the Au–TiO x interface at the perimeter and the extent of Ti isolation in the TiO x phase in the reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Element redistributions during early stages of oxidation in a Ni38Cr22Fe20Mn10Co10 multi-principal element alloy

Element redistributions after initial gaseous oxidation of a Ni38Cr22Fe20Mn10Co10 (at%) multi-principle element alloy at 120°C and 300°C is captured via psuedo in situ atom probe tomography. All cations contribute to the oxide in both conditions, consisting of a Cr-rich inner oxide and Fe, Mn, Co and Ni-rich outer oxide. At the lower temperature, Ni tends to be trapped at the outer/inner oxide interface, while Ni enriches at the oxide/metal interface at higher temperature in tandem with Cr metal depletion. These observations confirm oxidation of complex alloys involves the formation of metastable, multi-layered oxide films, with a distinct tendency for solute trapping.

multi-principal element alloy, oxidation mechanism↗

Probing the active sites of oxide encapsulated electrocatalysts with controllable oxygen evolution selectivity

Electrocatalysts encapsulated by nanoscopic overlayers can control the rate of redox reactions at the outer surface of the overlayer or at the buried interface between the overlayer and the active catalyst, leading to complex behavior in the presence of two competing electrochemical reactions. This study investigated oxide encapsulated electrocatalysts (OECs) comprised of iridium (Ir) thin films coated with an ultrathin (2–10 nm thick) silicon oxide (SiO x ) or titanium oxide (TiO x ) overlayer. The performance of SiO x |Ir and TiO x |Ir thin film electrodes towards the oxygen evolution reaction (OER) and Fe(II)/Fe(III) redox reactions were evaluated. An improvement in selectivity towards the OER was observed for all OECs. Overlayer properties, namely ionic and electronic conductivity, were assessed using a combination of electroanalytical methods and molecular dynamics simulations. SiO x and TiO x overlayers were found to be permeable to H 2 O and O 2 such that the OER can occur at the MO x |Ir (M = Ti, Si) buried interface, which was further supported with molecular dynamics simulations of model SiO 2 coatings. In contrast, Fe(II)/Fe(III) redox reactions occur to the same degree with TiO x overlayers having thicknesses less than 4 nm as bare electrocatalyst, while SiO x overlayers inhibit redox reactions at all thicknesses. This observation is attributed to differences in electronic transport between the buried interface and outer overlayer surface, as measured with through-plane conductivity measurements of wetted overlayer materials. These findings reveal the influence of oxide overlayer properties on the activity and selectivity of OECs and suggest opportunities to tune these properties for a wide range of electrochemical reactions.

08 HYDROGEN↗

Oxide Epitaxy with Large Symmetry Mismatch: Bronze-phase VO 2 on SrTiO 3

Epitaxial synthesis of complex oxides has stimulated considerable interest in creating novel functionalities and physical properties by controlling the interplay among the order parameters, i.e. lattice, spin, charge, and orbital order. Furthermore, heterostructures of oxide materials allow for well defined interfaces at which electronic and/or magnetic order can be coupled or tuned, as well as giving rise to emergent behavior distinct from the bulk properties of either material. Most studies on the epitaxial growth of complex oxides have focused on isostructural materials, e.g. perovskites on perovskites. While many binary oxides, such as TiO 2 and VO 2 , also offer intriguing physical properties, there are no substrates available with similar structures (lattice parameters and crystal symmetry). Thus, the ability to grow epitaxial thin films of binary oxides on lattice- and symmetry-mismatched substrates is of vital importance for exploring their unprecedented potential.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tuning Selectivity of CO 2 Hydrogenation Reactions at the Metal/Oxide Interface

The chemical transformation of CO 2 not only mitigates the anthropogenic CO 2 emission into the Earth’s atmosphere but also produces carbon compounds that can be used as precursors for the production of chemicals and fuels. The activation and conversion of CO 2 can be achieved on multifunctional catalytic sites available at the metal/oxide interface by taking advantage of the synergy between the metal nanoparticles and oxide support. In this paper, we look at the recent progress in mechanistic studies of CO 2 hydrogenation to C1 (CO, CH 3 OH, and CH 4 ) compounds on metal/oxide catalysts. On this basis, we are able to provide a better understanding of the complex reaction network, grasp the capability of manipulating structure and combination of metal and oxide at the interface in tuning selectivity, and identify the key descriptors to control the activity and, in particular, the selectivity of catalysts. In conclusion, we also discuss challenges and future research opportunities for tuning the selective conversion of CO 2 on metal/oxide catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface Hydration and Hydroxyl Configurations of Gibbsite and Boehmite Nanoplates

Discontinuation of the bulk structure at the interface between metal oxide particles and water leads to altered bonding characteristics and unique facet-dependent molecular environments. Surface hydration and consequent hydroxylation adds further complexity to the interface, details that for metal (oxy)hydroxides are especially difficult to isolate from the background signal of bulk structural hydroxyls. Here we probe for the first time the hydroxylation and hydration structures on basal surfaces of gibbsite (?-Al(OH)3) and boehmite (?-AlOOH) nanoplates at ambient conditions, using the interface-sensitive technique vibrational sum frequency generation spectroscopy (VSFG). Hydroxyl stretching modes at the interfaces with adsorbed water layers compared directly to Raman and infrared bulk modes show that while gibbsite surface frequencies were sharp and nearly identical to those in the bulk, boehmite surface hydroxyls displayed a very different broad spectrum of states. Ab initio molecular dynamics simulations of both basal surfaces with and without hydration waters reveal that gibbsite surface hydroxyls interact only weakly with overlying hydration waters remaining essentially unperturbed, whereasthose on boehmite can interact more strongly facilitated by higher configurational degrees of freedom at the interface. The findings clearly unveil substantial differences in the hydrated interfacial dynamics of these two otherwise similar materials, with implications for their interfacial chemistry and wettability.

Sassi, Michel JPC↗

Mechanisms of interfacial reactivity in near surface and extreme environments

The local water structure surrounding ions in aqueous solutions greatly affects their chemical properties such as reaction rates, ion association, and proton and electron transport. These properties result in the behavior of ions in natural aqueous environments. For example ore transport is facilitated by chloride ion pair formation and the reaction of ions in an interface is strongly dependent on the dehydration of the ion hydration shell. We are developing the use of high-­resolution XAFS observations and 1st principles based MD-­XAFS analysis (spectra simulated using 1st principle methods with no adjustable parameters, AIMD) to interpret the solution properties of strongly interacting aqueous solutes under arbitrary pressure and temperature conditions. In the 1st principle MD-­XAFS method density functional theory (DFT) based MD simulations(Car and Parrinello, 1985) are used to generate a large ensemble of structural snap shots of the hydration region. These are then used to generate scattering intensities. I emphasize three points about this novel approach to analyzing XAFS data. 1st: As illustrated in Figure 1, the level of agreement between the calculated and observed intensities is considerably higher than has been obtained by any XAFS analysis to date (note 2nd shell region, R> 2 Å). 2nd: This result was obtained from a parameter free simulation with no fitting of the interaction potentials to any data. This supports the use of these methods for more difficult environments and more complex solutes (polyions). 3rd: New information about the shell structure (Figure 1) is now available because of this more detailed agreement. We note also that both multiple scattering and second shell features are well represented in the analysis. As far as we know this is the 1st analysis of second shell structure and multiple scattering. Excellent agreement has been obtained for most of the third row metal ions: Ca 2+ , Zn 2+ , Cu 2+ , Ni 2+ , Co 2+ , Mn 2+ , Fe 3+ , Cr 3+ . Calculations on these systems are demanding because of their open electronic shells, and high ionic charge. Principal Investigator: Professor John Weare (University of California, San Diego) The prediction of the interactions of geochemical fluids with minerals, nanoparticles, and colloids under extreme near surface conditions of temperature (T) and pressure (P) is a grand challenge research need in geosciences (U.S. DOE 2007, Basic Research Needs for Geosciences: Facilitating the 21st Energy Systems.). To evaluate the impact of these processes on energy production and management strategies it is necessary to have a high level of understanding of the interaction between complex natural fluids and mineral formations. This program emphasizes 1st principle parameter free simulations of complex chemical processes in solutions, in the mineral phase, and in the interfaces between these phases The development of new computational tools (with emphasis on oxide materials and reaction dynamics) tailored to treat wide range of conditions and time scales experienced in such geochemical applications is has been developed. Because of the sensitivity of the interaction in these systems to electronic structure and local bonding environments, and of the need to describe bond breaking/formation, our simulations are based on interactions calculated at the electronic structure level (ab-initio molecular dynamics, AIMD). The progress in the computational aspects of program may be summarized in terms of the following themes (objectives); Development of efficient parameter free dynamical simulation technology based on 1st principles force and energy calculations especially adapted for geochemical applications (e.g., mineral, interfaces and aqueous solutions) (continuing program); Calculation of the dynamics of water structure of in the surface-water interface of transition metal oxides and oxihydroxides; and Development of improved (beyond DFT+GGA) electronic structure calculations for minerals and the interface region that more accurately calculate electron correlation, spin density, and localization. The focus of the program is also on the iron oxide and oxihydroxide minerals and Fe 2+ (aq)/Fe 3+ (cr) oxidation in the mineral solution interface region. These methods included the development of model Hamilitonian methods that can be solved to near convergence for single site models (DMFT) and many-body perturbation methods (MP2, GW); Development of time decomposition methods to extend time scales of molecular dynamics (MD) simulations and support the use of high complexity electronic structure calculations (MP2, CCSD(T)) of forces for use in dynamical simulations where very high chemical accuracy is required (microsolvated reactions in absorbed surface layers); and The development of a new linear scaling finite element solver for eigenvalue problem that supports solution of quantum problems with unusual potential and boundary values. Application progress of the above new simulation technology to problems of geochemical interests includes; The prediction of metal oxide surface structure and the reduction/oxidation of Fe 3+ (cr)/Fe 2+ (aq) in metal oxide (hematite, goethite)/solution interfaces. Result: water interacts strongly with the 001 Hematite surface; interaction of water with the 100 goethite is weak; The study of ion solvation and the composition of ion hydration shells under extreme conditions (focus on Fe 3+/2+ , Al 3+ and Mg 2+ and their hydroxide speciation). Result: Ion association in water solutions can be calculated from 1st principle methods. Efficient sampling of the free energy requires more development; The continued development of new high resolution analysis of XAFS scattering of disordered systems (particularly Al, Mg) and of XANES calculations for aqueous ions. Result: EXAFS spectra can be calculated to high accuracy with DFT level dynamic simulations; The exploration of electron localization and electron transport in metal oxides (highly correlated materials). Result: Proper description of electron localization requires levels of calculation beyond DFT; and Localization of electrons in DFT type Hamiltonians was studied. Result: For very Dirac high exchange new solutions (New unphysical bifrucations) to the eigenvalue problem are found. The program was highly collaborative involving faculty and students in mathematics, physics and computer science departments as well as coworkers at the Pacific Northwest National Laboratories (PNNL). The students in this program had the opportunity to develop skills in the development of methods, the implementation of method on high performance parallel computers and the application of these methods to problem in geochemical science. Much of the software that was developed was incorporated in the NWchem software package maintained by PNNL.

58 GEOSCIENCES↗

Computer-Aided Molecular Design of Bis-phosphine Oxide Lanthanide Extractants

Computer-aided molecular design and high-throughput screening of viable host architectures can significantly reduce the efforts in the design of novel ligands for efficient extraction of rare earth elements. This paper presents a computational approach to the deliberate design of bis-phosphine oxide host architectures that are structurally organized for complexation of trivalent lanthanides. Molecule building software, HostDesigner, was interfaced with molecular mechanics software, PCModel, providing a tool for generating and screening millions of potential R 2 (O)P-link-P(O)R 2 ligand geometries. The molecular mechanics ranking of ligand structures is consistent with both the solution-phase free energies of complexation obtained with density functional theory and the performance of known bis-phosphine oxide extractants. For the case where link is -CH 2 -, evaluation of the ligand geometry provides the first characterization of a steric origin for the ‘anomalous aryl strengthening’ effect. The design approach has identified a number of novel bis-phosphine oxide ligands that are better organized for lanthanide complexation than previously studied examples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Heterogeneous Integration of Flipped Oxide Heterostructure Membranes for Nanoelectronics

Freestanding complex oxide membranes enable the release and transfer of epitaxial films, offering new design freedoms for next‐generation electronics. While the LaAlO 3 /SrTiO 3 (LAO/STO) heterostructure exhibits remarkable tunable conductivity at its interface, the active interface remains buried beneath the substrate, limiting access to this functionality. Here, we demonstrate how the LAO/STO heterostructure, in membrane form, can be flipped and precisely positioned on silicon and other platforms using polymer‐free micromanipulation. The transferred membranes preserve atomically smooth surfaces, high crystallinity, and key electronic properties. Through the 44‐nm insulating STO layer, ultra‐low‐voltage electron‐beam lithography (ULV‐EBL) writes conductive nanostructures at the now‐accessible STO/LAO interface, offering the potential to function as programmable local gates that modulate charge carriers in the underlying silicon. The platform establishes a general strategy for integrating complex oxide heterostructures with semiconductors, quantum materials, and flexible substrates, enabling new architectures for reprogrammable nanoelectronic devices.

36 MATERIALS SCIENCE↗

Interfacial Magnetism in Complex Oxide Heterostructures Probed by Neutrons and X-rays

Magnetic complex-oxide heterostructures are of keen interest because a wealth of phenomena at the interface of dissimilar materials can give rise to fundamentally new physics and potentially valuable functionalities. Altered magnetization, novel magnetic coupling and emergent interfacial magnetism at the epitaxial layered-oxide interfaces have all been intensively investigated, which shapes our understanding on how to utilize those materials, particularly for spintronics. Neutron and x-ray based techniques have played a decisive role in characterizing interfacial magnetic structures and clarifying the underlying physics in this rapidly developing field. Here we review some recent experimental results, with an emphasis on those studied via polarized neutron reflectometery and polarized x-ray absorption spectroscopy. We conclude with some perspectives.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Toward Photochemical Water Splitting Using Band-Gap-Narrowed Semiconductors and Transition-Metal Based Molecular Catalysts

We are carrying out coordinated theoretical and experimental studies of toward photochemical water splitting using band-gap-narrowed semiconductors (BGNSCs) with attached multi-electron molecular water oxidation and hydrogen production catalysts. We focus on the coupling between the materials properties and the H{sub 2}O redox chemistry, with an emphasis on attaining a fundamental understanding of the individual elementary steps in the following four processes: (1) Light-harvesting and charge-separation of stable oxide or oxide-derived semiconductors for solar-driven water splitting, including the discovery and characterization of the behavior of such materials at the aqueous interface; (2) The catalysis of the four-electron water oxidation by dinuclear hydroxo transition-metal complexes with quinonoid ligands, and the rational search for improved catalysts; (3) Transfer of the design principles learned from the elucidation of the DuBois-type hydrogenase model catalysts in acetonitrile to the rational design of two-electron hydrogen production catalysts for aqueous solution; (4) Combining these three elements to examine the function of oxidation catalysts on BGNSC photoanode surfaces and hydrogen production catalysts on cathode surfaces at the aqueous interface to understand the challenges to the efficient coupling of the materials functions.

08 HYDROGEN↗

Identification of donor deactivation centers in heavily As-doped Si using time-of-flight medium-energy ion scattering spectroscopy

Electrically-inactive arsenic (As) complexes in silicon are investigated using time-of-flight medium-energy ion scattering spectroscopy. In heavily As-doped Si, the As atoms that are segregated in the Si interface region just below the SiO{sub 2} are found to be in interstitial forms (As{sub i}), while the As atoms in the bulk Si region are found to be in the substitutional form (As{sub Si}). Despite the substitutional form of As, most of the As are found to be electrically inactive in the bulk region, and we identify the As to be in the form of a 〈111〉-oriented As{sub Si}-Si-vacancy (As{sub Si}-V{sub Si}) complex. The As{sub i} atoms in the interface Si region are found to exist together with Si-interstitial atoms (Si{sub i}), suggesting that the As{sub i} atoms in the interface Si region accompany the Si{sub i} atoms.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Field-dependent magnetization of BiFeO 3 in ultrathin La 0.7 Sr 0.3 MnO 3 /BiFeO 3 superlattice

We report the observation of field-induced magnetization of BiFeO 3 (BFO) in an ultrathin La 0.7 Sr 0.3 MnO 3 (LSMO)/BFO superlattice using polarized neutron reflectivity (PNR). The depth dependent structure and magnetic characterization of subnano layer thick (thickness ~ 0.7 nm each) LSMO/BFO hetrostructure is carried out using X-ray reflectivity and PNR techniques. Our PNR results indicate parallel alignment of magnetization as well as enhancement in magnetic moment across LSMO/BFO interfaces. The study showed an increase in average magnetization on increasing applied magnetic field at 10K. As a result, we observed a saturation magnetization of 110 ± 15 kA/m (~0.8 μ B /Fe) for ultrathin BFO layer (~2 unit cell) sandwiched between ultrathin LSMO layers (~ 2 unit cell).

74 ATOMIC AND MOLECULAR PHYSICS↗

In Situ Electrochemistry of Buried Interfaces in Metal Halide Perovskites: Probing Energy Bands, Halide Redox Activity, and Kinetics

Control over charge injection and extraction processes across buried interfaces is fundamental for all (opto)electronic multilayer device platforms, necessitating detailed understanding of local structural and chemical differences that promote defect formation, distort energetic band-edge alignments, and alter charge transport processes. Herein, the implementation of a low-cost electroanalytical methodologies’ tool suite is described to quantitatively characterize buried interfaces and redox reactions in printable, mixed electrical–ionic, and redox-active metal halide perovskites and a prototypical hole-transporting nickel oxide (NiO x ) thin film. The objective is to demonstrate the power of electrochemical methodologies to improve the nanoscale understanding of complex interfaces within optoelectronic devices by providing case studies on how to: i) differentiate between electronic and chemical properties in NiO x contacts; ii) measure changes in reversibility of halide redox reactions via NiO x surface states; iii) assess energy alignment and charge transport across (modified) buried interfaces; and iv) quantify defects at buried interfaces that change with modifiers and differences in perovskite processing, including increasing defect concentrations when films are slot-die-coated versus spin-cast. The collective approach addresses major challenges in understanding the precise energy landscape and interface reactivity under relevant electric fields that mimic operando conditions (away from equilibrium) and across length scales in thin film device formats.

(spectro)electrochemistry↗

Interface engineering of phase separation in SrRuO 3 /SrTiO 3 hybrid superlattices

Most observed phase separation phenomena in complex oxides occur in systems with chemical dopants or structural defects, and theories have established the strong connection between phase separation and the random distribution of chemical dopants. Recent experiments on fabricated high-quality oxide superlattices also confirmed that the phase separation is suppressed in the clean systems without chemical disorders. Thus far, phase separation in strongly correlated oxides without the need of chemical dopants or structural defects has not been fully demonstrated. Here, we have built chemically ordered hybrid superlattices using prototypical SrRuO 3 and SrTiO 3 perovskite oxides. Contrary to previous understandings, we observe phase separation of two magnetic phases with different spin easy axes. We elucidate this phenomenon through first-principles calculations that the hybrid superlattices have a spontaneous structural instability, leading to a coexistence of ferromagnetic and antiferromagnetic phases. In this work, our findings provide an alternative pathway other than chemical doping to introduce phase separation in correlated oxides and imply that phase separation can exist in clean systems without the need of chemical disorders.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Role of scaffold network in controlling strain and functionalities of nanocomposite films

One novel approach to manipulating functionalities in correlated complex oxides is strain. However, significant epitaxial strain can only be achieved in ultrathin layers. We show that, under direct lattice matching framework, large and uniform vertical strain up to 2% can be achieved to significantly modify the magnetic anisotropy, magnetism, and magnetotransport properties in heteroepitaxial nanoscaffold films, over a few hundred nanometers in thickness. Comprehensive designing principles of large vertical strain have been proposed. Phase-field simulations not only reveal the strain distribution but also suggest that the ultimate strain is related to the vertical interfacial area and interfacial dislocation density. Moreover, by changing the nanoscaffold density and dimension, the strain and the magnetic properties can be tuned. The established correlation among the vertical interface—strain—properties in nanoscaffold films can consequently be used to tune other functionalities in a broad range of complex oxide films far beyond critical thickness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

La-doped BaTiO{sub 3} heterostructures: Compensating the polarization discontinuity

We demonstrate a route to manipulate the polarization and internal electric field of a complex oxide heterostructure using a layering sequence based on the LaAlO{sub 3}-SrTiO{sub 3} interface. By combining sensitive atomic-level mapping of the structure using direct x-ray phase-retrieval methods with theoretical modeling of the electrostatic charge and polarization, we have devised a novel single-domain polar heterostructure. We find that ionic rearrangement results in strain and free energy minimization, and eliminates the polarization discontinuity leading to a two-fold increase of the spontaneous polarization towards the surface of an ultra-thin single-domain BaTiO{sub 3} film.

36 MATERIALS SCIENCE↗