Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “civil engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗
DOE OSTI2023

On the convergence of statistics in simulations of stationary incompressible turbulent flows

When reporting statistics from simulations of statistically stationary chaotic phenomenon, it is important to verify that the simulations are time-converged. This condition is connected with the statistical error or number of digits with which statistics can be reliably reported. In this work we consider numerical experiments of low Reynolds number incompressible homogeneous and isotropic turbulence as a model problem to investigate statistical convergence over finite simulation times. Specifically, we investigate the time integration requirements that allow meaningful reporting of the statistical error associated with finiteness of the temporal domain. We address two key questions: (1) How long should a simulation be performed in terms of large eddy time, and (2) How should the simulation time be divided among temporal windows over which a quantity of interest is estimated so that its statistical error could be reliably reported? We find that reliable reporting of statistical errors requires simulations on the order of 10 4 large eddy times, which is orders of magnitude longer than typically performed. Additionally, data post-processing should employ windows of at least ten times the large eddy time scale, with the most robust computation of statistical error of the mean requiring window sizes of an additional factor of ten. For practical simulations, we demonstrate that it is possible to estimate the statistical error within a factor of two under a less stringent condition in which a minimum of four windows with size at least ten large eddy times are used. In conclusion, our observations for homogeneous isotropic turbulence are also shown to hold in turbulent channel flow.

42 ENGINEERING↗
DOE OSTI2025

Adaptive Interface-PINNs (AdaI-PINNs) for transient diffusion: Applications to forward and inverse problems in heterogeneous media

We model transient diffusion in heterogeneous materials using a novel physics-informed neural networks framework (PINNs) termed Adaptive interface physics-informed neural networks or AdaI-PINNs (Roy et al. arXiv preprint arXiv:2406.04626, 2024). AdaI-PINNs utilize different activation functions with trainable slopes tailored to each material region within the computational domain, allowing for a fully automated and adaptive PINNs approach to model interface problems with strongly and weakly discontinuous solutions. To enhance its performance in highly heterogeneous transient diffusion systems, we prescribe a suite of robust practices, including appropriate non-dimensionalization of equations, a biased sampling method, Glorot initialization, and the hard enforcement of boundary and initial conditions. Here we evaluate the efficacy of the proposed method on several benchmark forward and inverse problems. Comparative studies on one-dimensional and two-dimensional benchmark problems reveal that the modified AdaI-PINNs outperform its unmodified counterpart, achieving root-mean-square errors that are at least two orders of magnitude better in forward problems. For inverse problems, the maximum errors in the approximated diffusion coefficients by modified AdaI-PINNs are four orders of magnitude better than those of the unmodified version. Additionally, modified AdaI-PINNs demonstrate improved stability in problems with large material mismatches.

42 ENGINEERING↗
DOE OSTI2026

Capturing the fractocohesive length scale in elastomers through a statistical mechanics-based gradient enhanced damage model

Here, this study aims to examine modeling flaw sensitivity in elastomers. The direct incorporation of polymer chain statistical mechanics considerations into a continuum stretch-based gradient-enhanced damage formulation, in turn, allows a representation of diffuse chain damage and fracture events that align with known micromechanical mechanisms. Through a series of numerical experiments, we simulate crack propagation and extract the fracture energy as an output of the model, while keeping track of the micromechanical signatures of diffuse chain damage that accommodate fracture propagation and eventually influence flaw sensitivity. Finally, by combining the fracture toughness and the work to rupture, we identify a fractocohesive length of the material, corresponding to the full width of the damage process zone. As the damage-to-fracture cascade in the proposed GED model is influenced by the introduction of a length scale associated with network imperfection and long-range load transfer, the emerging relationship of the two length scales is discussed, providing a potential link between microscopic damage mechanisms and the observed macroscopic fracture response.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Dynamic crushing of metal lattice metamaterials: Shock mode diagrams and transition to topology-independent compaction regime

Additively manufactured lattice metamaterials offer design versatility in strength and energy absorption and provide an additional degree of freedom through the selection of the lattice topology. Under quasistatic loading, the unit cell structure can strongly affect the stiffness, yield, and post-yield behavior, but whether and to what degree the effect of lattice topology persists into dynamic loading scenarios, up to the compaction shock regime, has not been established. LLNL’ s ALE3D hydrocode was used to perform a computational investigation of dynamic loading in multiple lattice types, including the gyroid, octet, Schwarz D, and rhombic dodecahedron, under impact velocities from 0.25 to 2.25 km/s. Shock Hugoniots for each lattice topology are generated and compared, suggesting that above a critical velocity, distinctions between architectures may not persevere and compacted lattices behave similarly. Here, to investigate the transition between topology-dependent quasistatic compression and the topology-independent regime above the critical velocity, a one-dimensional elastic-linear hardening plasticity-densified solid (E-LHP-DS) shock model for lattice materials was developed that relies upon confined compression to link the quasistatic and shock mechanics. Unlike similar works, the model does not assume rigid behavior prior to yield or locking behavior at densification, allowing a richer exploration of lattice mechanics. With only six parameters, the analytical model simultaneously fit quasistatic confined compression simulations for relative densities 0.1 $≤ \bar{ρ} ≤$ 0.9 and predicted dynamic compaction behavior to traverse several distinct shock modes, each defined by a critical impact speed (equivalently, critical stresses). Comparing the numerical results to the one-dimensional E-LHP-DS shock model predictions suggests that the topology-independence under strong shocks is linked to the onset of densification, which can be predicted based on quasistatic confined compression results.

Cellular material↗
DOE OSTI2025

Direct sensitivity analysis on the parameterization of crystal plasticity models

Various methods for calibrating crystal plasticity finite element (CPFE) models lead to non-unique input parameter values, which subsequently introduce uncertainty in the predicted mechanical response. Sensitivity analysis (SA) conducted on crystal plasticity models is used to identify how variability in these parameters contribute to output uncertainty. Traditional SA on CPFE parameters uses simplified surrogate models to save computational time. However, the accuracy of the surrogate models depends on the quantity of training data used, and any modeling error can propagate into the SA results, potentially affecting their reliability. In this work, the elementary effects test (EET) method, a global SA technique using direct CPFE simulations was employed, and the results obtained were compared with the First Order Second Moment (FOSM) method. ExaConstit, an open-source GPU-enabled CPFE code, was used to perform the simulations and direct SA. The EET method was accurately able to capture the non-linear effects of all the input parameters on the output and is a valuable approach for reliably attributing parameter sensitivities in CPFE models. Based on the results, efficient strategies to perform future parameter calibration and SA are discussed. Additionally, the SA trends observed in different single crystal orientations closely mirrored the activity of the slip systems.

Elementary Effects Test↗
DOE OSTI2025

Elucidating texture and grain morphology contributions to the micromechanical response of additively manufactured Inconel 625

Microstructural variation of additively manufactured (AM) metal components in comparison to wrought counterparts makes certification for critical applications a challenge. Microscale simulations leveraging modern computational tools may be used to supplement testing of AM microstructures, thus accelerating certification by reducing the number of experiments needed. However, as micromechanical response is closely tied to critical properties like fatigue-life and fracture, utilization of these simulations with macroscale experimental data alone is insufficient. One means to attain microscale experimental data is in situ diffraction data collected from synchrotron X-ray sources. In this work, such data were collected during in situ compression of AM Inconel 625 superalloy. Interpretation of experimental results was assisted by massive (8M element) complementary micromechanical simulations performed on sets of virtual microstructures generated using cellular automata. Together, micromechanical data from diffraction experiments and simulations were used to probe the effects of textured “track” microstructures generated during laser powder bed fusion and directional strength-to-stiffness on micromechanical response. Though fiber-averaged directional strength-to-stiffness ratios were expected to dominate given the high elastic anisotropy of the material, the combination of small variations in texture and specific grain configurations unique to AM microstructures lead to significant variability in micromechanical response after yield. The findings emphasize the importance of high-fidelity microstructural representation that captures key texture components and AM-specific morphology for property prediction of AM metals.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High strain-rate strength response of single crystal tantalum through in-situ hole closure imaging experiments

The properties of crystalline materials often depend on directionality and operating conditions. Specifically, the strength of materials can depend anisotropically on crystal direction and the loading condition. To probe these effects, a preliminary series of high strain-rate (> 105/s) strength plate-impact hole closure experiments were performed on high purity single crystal Tantalum cubes. The orientation of the single crystals with respect to impact/loading were varied to provide data to inform crystal plasticity modeling efforts. The experiments consist of in-situ high-resolution X-ray radiographic imaging of the hole collapse under dynamic compression conditions to infer the material strength via its resistance to closure at increasing levels of plastic strain. The experiments are compared against hydrocode simulation predictions. Here, a comparison with simple elastic perfectly plastic strength model predictions is presented to elucidate the response of the different crystal orientations at high strain-rate and large plastic strains.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Stochastic modal velocity field in rough-wall turbulence

Stochastically generated instantaneous velocity profiles are used to reproduce the outer region of rough-wall turbulent boundary layers in a range of Reynolds numbers extending from the wind tunnel to field conditions. Each profile consists in a sequence of steps, defined by the modal velocities and representing uniform momentum zones (UMZs), separated by velocity jumps representing the internal shear layers. Height-dependent UMZ is described by a minimal set of attributes: thickness, mid-height elevation, and streamwise (modal) and vertical velocities. These are informed by experimental observations and reproducing the statistical behaviour of rough-wall turbulence and attached eddy scaling, consistent with the corresponding experimental datasets. Sets of independently generated profiles are reorganized in the streamwise direction to form a spatially consistent modal velocity field, starting from any randomly selected profile. The operation allows one to stretch or compress the velocity field in space, increases the size of the domain and adjusts the size of the largest emerging structures to the Reynolds number of the simulated flow. By imposing the autocorrelation function of the modal velocity field to be anchored on the experimental measurements, we obtain a physically based spatial resolution, which is employed in the computation of the velocity spectrum, and second-order structure functions. The results reproduce the Kolmogorov inertial range extending from the UMZ and their attached-eddy vertical organization to the very-large-scale motions (VLSMs) introduced with the reordering process. The dynamic role of VLSM is confirmed in the –u'w' co-spectra and in their vertical derivative, representing a scale-dependent pressure gradient contribution.

42 ENGINEERING↗
DOE OSTI2024

Direct numerical simulations of three-component Rayleigh–Taylor mixing and an improved model for multicomponent reacting mixtures

We present direct numerical simulations of a three-layer Rayleigh–Taylor instability (RTI) problem with a configuration based on the experiments of Suchandra & Ranjan ( J. Fluid Mech. , vol. 974, 2023, A35) and Jacobs & Dalziel ( J. Fluid Mech. , vol. 542, 2005, pp. 251–279). The problem consists of a layer of light fluid between two layers of heavy fluid with an Atwood number of 0.3. These simulations are first validated through comparison with available experimental data. The validated simulations are then utilized to analyse statistics in this three-component flow. First, length scales are examined utilizing spectra and two-point spatial correlations of velocity and species concentration fluctuations. Next, joint probability density functions (p.d.f.s) of species concentration are compared against several model p.d.f.s representing generalizations of the bivariate beta distribution. Notably, the joint p.d.f.s do not appear to be accurately described by a Dirichlet distribution, indicating the marginal distributions do not conform to a beta distribution. Finally, similarity of the present configuration to three-component mixing found in inertial confinement fusion (ICF) applications is exploited to develop and validate an improved model for the impact of multicomponent mixing on thermonuclear (TN) reaction rates. A single time instant from the present simulations is chosen for a TN burn calculation under the hypothetical assumption of ICF materials and temperatures. Total TN output from this second calculation is then compared against the prediction of the improved model. The new model is found to accurately predict TN reaction rates in both premixed and non-premixed configurations.

42 ENGINEERING↗
DOE OSTI2024

Parameters and surrounding rock control of gob-side driving under double key stratum after roof cutting

Taking the return-airway 4204 with roof cutting in Longquan Coal Mine as the engineering background, roof structure, key parameters, and deviatoric stress evolution were studied. Conclusion: The Key Stratum within a 4–8 times mining height is considered as Near Key Stratum. Cutting the roof makes it possible to form a cantilever structure of the Key Stratum on the solid coal side, which is more conducive to the stability of gob-side roadway. During cutting angle of 90–55°, the deviatoric stress increases linearly, and the increase rate is coal pillar > solid coal > roof > floor. While cutting length from 0 to 35 m, the deviatoric stress decreases linearly, and the decreasing range: coal pillar > solid coal > roof > floor. When coal pillar width is from 30 to 4 m, the deviatoric stress of left side and floor presents a “single peak” distribution. The deviatoric stress of coal pillar changes from an asymmetric “double peak” to a bell-shaped distribution, and the deviatoric stress of roof changes from a “single peak” to an asymmetric “double peak” distribution. Under same coal pillar width, the deviatoric stress of left, coal pillar and roof after roof cutting decreases most obviously, followed by the floor. Finally, the coal pillar width is 8 m, the cutting angle is 75°, the cutting length is 20 m, and the hole spacing is 1.0 m. The support scheme is bolt + metal mesh + steel belt + anchor cable combined support. The stable period of roadway is about 10 days.

42 ENGINEERING↗
DOE OSTI2024

Spatial modeling algorithms for reactions and transport in biological cells

Biological cells rely on precise spatiotemporal coordination of biochemical reactions to control their functions. Such cell signaling networks have been a common focus for mathematical models, but they remain challenging to simulate, particularly in realistic cell geometries. Here we present Spatial Modeling Algorithms for Reactions and Transport (SMART), a software package that takes in high-level user specifications about cell signaling networks and then assembles and solves the associated mathematical systems. SMART uses state-of-the-art finite element analysis, via the FEniCS Project software, to efficiently and accurately resolve cell signaling events over discretized cellular and subcellular geometries. We demonstrate its application to several different biological systems, including yes-associated protein (YAP)/PDZ-binding motif (TAZ) mechanotransduction, calcium signaling in neurons and cardiomyocytes, and ATP generation in mitochondria. Throughout, we utilize experimentally derived realistic cellular geometries represented by well-conditioned tetrahedral meshes. These scenarios demonstrate the applicability, flexibility, accuracy and efficiency of SMART across a range of temporal and spatial scales.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Simultaneous inference of the compressibility and inelastic response of tantalum under extreme loading

We study the deformation of tantalum under extreme loading conditions. Experimental velocity data are drawn from both ramp loading experiments on Sandia’s Z-machine and gas gun compression experiments. The drive conditions enable the study of materials under pressures greater than 100 GPa. We provide a detailed forward model of the experiments including a model of the magnetic drive for the Z-machine. Utilizing these experiments, we simultaneously infer several different types of physically motivated parameters describing equation of state, plasticity, and anelasticity via the computational device of Bayesian model calibration. Characteristics of the resulting calculated posterior distributions illustrate relationships among the parameters of interest via the degree of cross correlation. The calibrated velocity traces display good agreement with the experiments up to experimental uncertainty as well as improvement over previous calibrations. Examining the Z-shots and gun-shots together and separately reveals a trade-off between accuracy and transferability across different experimental conditions. Implications for model calibration, limitations from model form, and suggestions for improvements are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

An enrichment wall modeling framework for spectral element methods

In the present work, a first-of-its-kind enrichment wall-model is developed within the spectral element method (SEM) framework for large-eddy simulations (LES) of wall-bounded turbulent flows. The method augments the polynomial solution in the wall-adjacent elements with an analytical law-of-the-wall enrichment function representing the mean velocity near the wall. In the solution representation, this enrichment function captures the large gradients in the boundary layer, which allows the polynomial modes to represent the turbulent fluctuations. The enriched solution is able to resolve the shear stress at the wall without any modification to the no-slip wall boundary conditions, which allows for greater accuracy in the near-wall region compared to traditional methods. The enrichment wall modeling approach is implemented in a high-order SEM computational fluid dynamics solver, Nek5000, and its performance is assessed in turbulent channel flow wall-modeled LES for a range of Reynolds numbers. It is demonstrated that the enrichment wall-model improves solution accuracy on under-resolved near-wall grids as compared to traditional shear stress wall-models.

42 ENGINEERING↗
DOE OSTI2026

The effect of dogbone sample size in the tensile testing of TATB-based plastic‑bonded explosive materials

Mechanical properties are of interest for many plastic‑bonded explosive (PBX) materials with tensile properties being of particular interest. Direct tensile measurements using dogbone-shaped samples are considered the gold standard, but they are fairly large, making testing more costly and less desirable from a safety perspective. We investigated whether the measured tensile strength depends on the dogbone specimen size, which to our knowledge, has not been reported in the literature for PBX materials. Understanding this should inform the feasibility of employing smaller samples and how sample size should be considered when comparing PBX dogbone values in the literature. The TATB-based PBX dogbone sample size was varied by (a) scaling all dimensions proportionally and (b) varying only the length of the samples. It was observed that the measured tensile peak stress (strength) was a function of the sample size, and was more dependent on the diameter (cross-sectional area) than the length of the samples. Since peak stress is calculated as peak force normalized to the diameter of the sample, one might not expect an explicit diameter dependence for the peak stress. Therefore, these results suggest there may be an additional strengthening effect as the sample diameter is increased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Vibrational processing of a dynamic structural flight system: A multichannel spectral estimation approach

Dynamic testing of large flight vehicles (rockets) is not only complex, but also can be very costly. These flights are infrequent and can lead to disastrous effects if something were to fail during the flight. The development of sensors coupled to internal components offers a great challenge in reducing their size, yet still maintaining their precision. Sounding rockets provide both a viable and convenient alternative to the more costly vehicular flights. Some of the major objectives are to test various types of sensors for monitoring components of high interest as well as investigating real-time processing techniques. Signal processing presents an extreme challenge in this noisy multichannel environment. The estimation and tracking of modal frequencies from vibrating structures is an important set of features that can provide information about the components under test; therefore, high resolution multichannel spectral processing is required. Finally, the application of both single channel and multichannel techniques capable of producing reliable modal frequency estimates of a vibrating structure from uncertain accelerometer measurements is discussed.

42 ENGINEERING↗