Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1960

Effect of Body-Mounted Lateral Controls and Speed Brakes on the Aerodynamic Load Distribution over a 45 deg Swept Wing at Mach Numbers from 0.80 to 0.98

An investigation has been made in the Langley 16-foot transonic tunnel to determine the effect of body-mounted lateral controls and speed brakes on the aerodynamic load distribution over a swept wing. The lateral controls and speed brakes consisted of flat plates which rotated out of the side of the fuselage, were approximately perpendicular to the wing chord plane, and extended either above or below the chord plane. The wing had 45 deg sweep of the quarter-chord line, an aspect ratio of 3, a taper ratio of0.2, and 4-percent-thick airfoil section. Data were obtained at Mach numbers of 0.80, 0.94, and 0.98 fir angels of attack that usually ranged from about 0 deg to 21 deg. The results show that at the higher angles of attack a lower-surface body-mounted lateral control located along the wing trailing edge had higher effectiveness than a similar upper-surface control. Reduction in span from 0.3 to 0.2 of the wing semispan of an upper-surface body-mounted lateral control located along the wing trailing edge resulted in a less than proportiona1,change in control effectiveness.

West, F. E., Jr.↗
NASA NTRS1993

Application of an Engineering Inviscid-Boundary Layer Method to Slender Three-Dimensional Vehicle Forebodies

An engineering inviscid-boundary layer method has been modified for application to slender three-dimensional (3-D) forebodies which are characteristic of transatmospheric vehicles. An improved shock description in the nose region has been added to the inviscid technique which allows the calculation of a wider range of body geometries. The modified engineering method is applied to the perfect gas solution over a slender 3-D configuration at angle of attack. The method predicts surface pressures and laminar heating rates on the windward side of the vehicle that compare favorably with numerical solutions of the thin-layer Navier-Stokes equations. These improvements extend the 3-D capabilities of the engineering method and significantly increase its design applications.

Riley, Christopher J.↗
NASA NTRS2018

Pterodactyl: Integrated Control Design for Precision Targeting of Deployable Entry Vehicles

Deployable Entry Vehicles (DEVs) enable in-situ scientific exploration at destinations with atmospheres across the solar system. Because they stow in a compact form and deploy only when ready to enter the atmosphere, DEVs relax the volume constraint imposed by rigid aeroshells. This work seeks to do for a DEV what the Wright Brothers did to propel modern day aviation: develop the guidance and control (G&C) methods that will make maneuvering and precision landing of DEV a reality. The Pterodactyl project objective is to deliver an integrated G&C methodology for a DEV, based on a detailed analysis that utilizes a Multi-disciplinary, Design, Analysis and Optimization (MDAO) framework. The current state-of-the-art for blunt body entry, G&C is rooted in the precision landing of vehicles such as Mars Science Laboratory (MSL) and Apollo, which used a propulsive reaction control system (RCS) to steer. Recent research has taken a particular interest in non-propulsive control for DEVs, including direct force control (angle of attack modulation via control surfaces or mass movement) and drag modulation (discrete change in ballistic coefficient). Using the MDAO framework that includes a guidance and control model to explore multiple control concepts for a DEV will shed light on the best design approach for these vehicles. In Pterodactyl, we will complete this study for a novel DEV concept, and then we will fabricate a functional prototype to help validate the design. The project is expected to down-select to a final control architecture by the end of 2018, and complete fabrication of the prototype by the end of 2019.The DEV chosen for detailed study in this project is the Adaptable Deployable Entry and Placement Technology (ADEPT). ADEPT uses a revolutionary 3D-woven carbon fabric that is foldable, can serve as primary structure, and can survive the extreme heating environment of atmospheric entry. The specific configuration of ADEPT under investigation is called Lifting Nano-ADEPT (LNA). LNA is designed for secondary payloads missions that require precision landing either for scientific objectives at a target destination or for payload recovery at Earth.The MDAO framework being created through this research, called COBRA-Pt (Composite Beam Roll-Up Solar Array-Prototype), will combine three critical elements of the system design: a guidance algorithm with Monte Carlo, a parametric control model, and vehicle geometry details. Novel control models being studied are deployable aerodynamic surfaces as well as shape morphing. These concepts will be compared at the system level with a more traditional propulsive RCS by comparing several key performance parameters. Upon completion of the design study, a functional prototype of LNA will be fabricated that will include the integration of guidance software and relevant control actuators. We expect this study will provide critical data that could feed into the development of an Earth-based flight test of LNA. The COBRA-Pt framework will provide a modular system by which to study any DEV concept in any atmosphere.

Smith, Brandon↗
NASA NTRS1997

Analysis of Wind Tunnel Longitudinal Static and Oscillatory Data of the F-16XL Aircraft

Static and oscillatory wind tunnel data are presented for a 10-percent-scale model of an F-16XL aircraft. Static data include the effect of angle of attack, sideslip angle, and control surface deflections on aerodynamic coefficients. Dynamic data from small-amplitude oscillatory tests are presented at nominal values of angle of attack between 20 and 60 degrees. Model oscillations were performed at five frequencies from 0.6 to 2.9 Hz and one amplitude of 5 degrees. A simple harmonic analysis of the oscillatory data provided Fourier coefficients associated with the in-phase and out-of-phase components of the aerodynamic coefficients. A strong dependence of the oscillatory data on frequency led to the development of models with unsteady terms in the form of indicial functions. Two models expressing the variation of the in-phase and out-of-phase components with angle of attack and frequency were proposed and their parameters estimated from measured data.

Klein, Vladislav↗
NASA NTRS1990

Aeolian Removal of Dust Types from Photovoltaic Surfaces on Mars

Dust elevated in local or global dust storms on the Martian surface could settle on photovoltaic (PV) surfaces and seriously hamper their performance. Using a recently developed technique to apply a uniform dust layer, PV surface materials were subjected to simulated Martian winds in an attempt to determine whether natural aeolian processes on Mars would sweep off the settled dust. Three different types of dust were used. The effects of wind velocity, angle of attack, height above the Martian surface, and surface coating material were investigated. It was found that arrays mounted on an angle of attack approaching 45 deg show the most efficient clearing. Although the angular dependence is not sharp, horizontally mounted arrays required much higher wind velocities to clear off the dust. From this test it appears that the arrays may be erected quite near the ground, but previous studies have suggested that saltation effects can be expected to cause such arrays to be covered by soil if they are set up less than about a meter from the ground. Particle size effect appear to dominate over surface chemistry in these experiments, but additional tests are required to confirm this.

Gaier, James R.↗
NASA NTRS1994

A simple analytical aerodynamic model of Langley Winged-Cone Aerospace Plane concept

A simple three DOF analytical aerodynamic model of the Langley Winged-Coned Aerospace Plane concept is presented in a form suitable for simulation, trajectory optimization, and guidance and control studies. The analytical model is especially suitable for methods based on variational calculus. Analytical expressions are presented for lift, drag, and pitching moment coefficients from subsonic to hypersonic Mach numbers and angles of attack up to +/- 20 deg. This analytical model has break points at Mach numbers of 1.0, 1.4, 4.0, and 6.0. Across these Mach number break points, the lift, drag, and pitching moment coefficients are made continuous but their derivatives are not. There are no break points in angle of attack. The effect of control surface deflection is not considered. The present analytical model compares well with the APAS calculations and wind tunnel test data for most angles of attack and Mach numbers.

Pamadi, Bandu N.↗
NASA NTRS1990

Aeolian Removal of Dust Types from Photovoltaic Surfaces on Mars

Dust elevated in local or global dust storms on the Martian surface could settle on photovoltaic (PV) surfaces and seriously hamper their performance. Using a recently developed technique to apply a uniform dust layer, PV surface materials were subjected to simulated Martian winds in an attempt to determine whether natural Aeolian processes on Mars would sweep off the settled dust. Three different types of dust were used; an optical polishing powder, basaltic "trap rock", and iron (III) oxide crystals. The effects of wind velocity, angle of attack, height above the Martian surface, and surface coating material were investigated. It was found that arrays mounted with an angle of attack approaching 45 degrees show the most efficient clearing. Although the angular dependence is not sharp, horizontally mounted arrays required significantly higher wind velocities to clear off the dust. From this test it appears that the arrays may be erected quite near the ground, but previous studies have suggested that saltation effects can be expected to cause such arrays to be covered by soil if they are set up less than about a meter from the ground. Particle size effects appear to dominate over surface chemistry in these experiments, but additional tests are required to confirm this. Providing that the surface chemistry of Martian dusts is not drastically different from simulated dust and that gravity differences have only minor effects, the materials used for protective coatings for photovoltaic arrays may be optimized for other considerations such as transparency, and chemical or abrasion resistance. The static threshold velocity is low enough that there are regions on Mars which experience winds strong enough to clear off a photovoltaic array if it is properly oriented. Turbulence fences proved to be an ineffective strategy to keep dust cleared from the photovoltaic surfaces.

Gaier, James R.↗
NASA NTRS1988

LDV surveys over a fighter model at moderate to high angles of attack

The vortex flowfield over an advanced twin-tailed fighter configuration has been studied in a low-speed wind tunnel at two angles of attack using LDV, along with laser light sheet and surface flow visualizations. At 15 deg angles of attack, the vortices generated by the wing leading edge extension (LEX) were found to be unburst over the model and to pass outboard of the vertical tail. At 25 deg angle of attack, the vortices were shown to burst in the vicinity of the wing-LEX intersection and to impact directly on the vertical tails.

Sellers, William L., III↗
NASA NTRS1933

Tests for the Elimination of Tail Flutter

On various low-wing monoplanes the horizontal tail surfaces flutter in flight at large angles of attack and occasionally in curvilinear flight. This flutter leads to torsional vibrations of the rear end of the fuselage, as manifested by vibrations of the control stick. According to the earlier DVL investigations tail flutter is due to the influence, on horizontal tail surfaces, of eddies or vortices shed at large angles of attack by the upper surface of the wing root. The cause of tail flutter on a low-wing monoplane and the means of preventing it are investigated in the present report.

Biechteler, Curt↗
NASA NTRS1983

An exploratory study of area-efficient vortex flap concepts

The potential of planform modification and hinge-line relocation to improve the thrust efficiency of vortex flaps was experimentally investigated on a 60-deg cropped delta wing model. Spanwise segmentation of the flap, together with chord-tailoring of the segments, allowed the vortex to be maintained on the outboard flap surfaces to higher angles of attack. In addition, location of the flap hinge aft of and underneath the wing leading edge generated substantial thrust from the vortex suction acting on the leading-edge lower surface. A combination of these beneficial effects allowed the flap/wing area to be reduced from 11.4 percent of the continuous flap to 6.3 percent of segmented flap, essentially without detriment to the incremental lift-to-drag ratio due to flap addition in the lift coefficient range 0.5-0.7 based on the basic wing area.

Rao, D. M.↗
NASA NTRS1960

Aerodynamic Characteristics at Low Speed of a Reentry Configuration Having Rigid Retractable Conical Lifting Surfaces

An exploratory investigation has been made in the Langley 300 MPH 7 by 10 foot tunnel to study the low-speed static longitudinal and lateral stability characteristics of a reentry configuration having rigid retractable conical lifting surfaces that unfolded from the surface of a conical fuselage. The model also had curved tail surfaces that unfolded from a cylindrical aft section attached to the cone. Longitudinal tests were made through an angle-of-attack range from -4 deg to 90 deg and limited lateral tests were made through an angle-of-sideslip range from -12 deg to 32 deg at an angle of attack of 0 deg. The tail surface provided longitudinal trim to maximum lift and beyond and up to an angle of attack of 51 deg for a center-of-moment location of 42.9 percent mean aerodynamic chord. For this center-of-moment position the model had a static margin of 12 percent mean aerodynamic chord at the lower lift coefficients and was longitudinally stable up to a lift coefficient between 1.0 and 1.2. Neutral stability occurred from lift coefficient of 1.0 up to near maximum lift coefficient. The maximum value of trimmed lift-drag ratio was 4.85 at a lift coefficient of approximately 0.3 and a trimmed angle of attack of approximately 10 deg. The configuration was directionally stable throughout the test angle of sideslip range for an angle of attack of 0 deg.

Fournier, Paul G.↗
NASA NTRS1990

In-flight flow visualization with pressure measurements at low speeds on the NASA F-18 high alpha research vehicle

In-flight results from surface and off-surface flow visualizations and from extensive pressure distributions document the vortical flow on the leading edge extensions (LEX) and forebody of the NASA F-18 high alpha research vehicle for low speeds and angles of attack up to 50 degs. Surface flow visualization data, obtained using the emitted fluid technique, were used to define separation lines and laminar separation bubbles. Off-surface flow visualization data, obtained by smoke injection, were used to document both the path of the vortex cores and the location of vortex core breakdown. The location of vortex core breakdown correlated well with the loss of suction pressure on the LEX and with the flow visualization results from ground facilities. Surface flow separation lines on the LEX and forebody corresponded well with the end of pressure recovery under the vortical flows. Correlation of the pressures with wind tunnel results show fair to good correlation.

Delfrate, John H.↗
NASA NTRS1990

In-flight flow visualization and pressure measurements at low speeds on the NASA F-18 high alpha research vehicle

Inflight results from surface and off surface flow visualizations and from extensive pressure distributions document the vortical flow on the leading edge extensions (LEXs) and forebody of the NASA F-18 high alpha research vehicle (HARV) for low speeds and angles of attack up to 50 deg. Surface flow visualization data, obtained using the emitted fluid technique, were used to define separation lines and laminar separation bubbles (LSB). Off surface flow visualization data, obtained by smoke injection, were used to document both the path of the vortex cores and the location of vortex core breakdown. The location of vortex core breakdown correlated well with the loss of suction pressure on the LEX and with the flow visualization results from ground facilities. Surface flow separation lines on the LEX and forebody corresponded well with the end of pressure recovery under the vortical flows. Correlation of the pressures with wind tunnel results show fair to good correlation.

John H Del Frate↗
NASA NTRS1975

Results of investigations (OA77 and OA78) on an 0.015-scale 140A/B configuration space shuttle vehicle orbiter model 49-0 in the AEDC VKF B and C wind tunnels, revision A

Aerodynamic data obtained from wind tunnel tests of an 0.015-scale 140A/B configuration SSV Orbiter model in the AEDC VKF B and C wind tunnels are presented. Tests were conducted at Mach numbers of 6 and 8 in the B tunnel and at a Mach number of 10 to in the C tunnel to verify hypersonic stability and control characteristics, determine control surface effectiveness, and investigate Reynolds number effects of the 140A/B configuration. Force data were obtained for various control surface settings and Reynolds numbers in the angle-of-attack range of 15 deg to 45 deg and at angles of sideslip of -5 deg to +10 deg. Data were obtained for a few configurations at angles of attack from -27 deg to 45 deg. Control surface variables included elevon, rudder, speedbrake and bodyflap deflections. The effects of an alternate wing leading edge shape were investigated to determine its hypersonic stability and control characteristics.

Gillins, R. L.↗
NASA NTRS1981

Experimental investigation of vortices shed by various wing fin configurations

Forty-six different fins, which were members of twelve plan-form families, were tested. A two dimensional Boeing single element airfoil at an angle of attack of eight degrees and a sweepback angle of thirty-two was used to simulate a portion of the wing of a generator aircraft. Various free stream velocities were used to test any individual fin at its particular angle of attack. While the fin itself was mounted on the upper surface of the generator model, the angle of attack of each fin was varied until stall was reached and/or passed. The relative fin vortex strengths were measured in two ways. First, the maximum angular velocity of a four blade rotor placed in the fin vortex center was measured with the use of a stroboscope. Second, the maximum rolling moment on a following wing model placed in the fin vortex center was measured by a force balance.

Iversen, J.↗
NASA NTRS1983

Viscous shock-layer predictions of three-dimensional nonequilibrium flows past the space shuttle at high angle of attack

Computational solutions were obtained for chemically reacting flowfields over the entire windward surface of the Space Shuttle at high angle of attack. The recently developed computational method for the Space Shuttle is capable of treating three dimensional viscous nonequilibrium air flow as well as equilibrium air and perfect gas flows. A general nonorthogonal computational grid system is used to treat the nonaxisymmetric geometry. Boundary conditions take into account noncatalytic wall, equilibrium with noncatalytic wall condition are compared to the fully catalytic wall solutions, the equilibrium air solutions, the perfect gas solutions, and also the Shuttle flight heating and pressure data. The comparisons show good agreement and correlations in most cases.

Kim, M. D.↗
NASA NTRS1999

Unstructured Grid Euler Method Assessment for Aerodynamics Performance Prediction of the Complete TCA Configuration at Supersonic Cruise Speed

Unstructured grid Euler computations, performed at supersonic cruise speed, are presented for a proposed high speed civil transport configuration, designated as the Technology Concept Airplane (TCA) within the High Speed Research (HSR) Program. The numerical results are obtained for the complete TCA cruise configuration which includes the wing, fuselage, empennage, diverters, and flow through nacelles at Mach 2.4 for a range of angles-of-attack and sideslip. The computed surface and off-surface flow characteristics are analyzed and the pressure coefficient contours on the wing lower surface are shown to correlate reasonably well with the available pressure sensitive paint results, particularly, for the complex shock wave structures around the nacelles. The predicted longitudinal and lateral/directional performance characteristics are shown to correlate very well with the measured data across the examined range of angles-of-attack and sideslip. The results from the present effort have been documented into a NASA Controlled-Distribution report which is being presently reviewed for publication.

Farhad Ghaffari↗