SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Static force tests have been made at low subsonic speeds for a model of a hypersonic research airplane in the Langley high-speed 7- by 10-foot tunnel to determine the aerodynamic forces and moments up to an angle of attack of 90 deg for a range of Reynolds numbers. The Reynolds numbers, based on the mean aerodynamic chord, ranged from 740,000 to 1,900,000, which correspond to dynamic pressures from 15 to 100 lb/sq ft (Mach numbers from 0.10 to 0.27). The model was tested in the clean configuration with various horizontal-tail settings, horizontal tail off, lower rudder off, fuselage alone, and with various size strakes and slats on the nose of the model. Representative results of the present investigation are presented in plotted form, and a tabulation of all the data obtained is presented in a table. Appreciable effects on side force, yawing moment, and pitching moment are indicated by changes in Reynolds number for angles of attack of 40 to 90 deg.
At the request of the Army Air Corps, an investigation of the pressure distribution over PW-9 wing models was conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. The primary purpose of these tests was to obtain wind-tunnel data on the load distribution on the cellule to be correlated with similar information obtained in flight tests, both to be used for design purposes. Because of the importance of the conditions beyond the stall as affecting the control and stability, this investigation was extended through 90 degree angle of attack. The results for the range of normal flight have been given in NACA Technical Report No. 271. The present paper presents the same results in a different form and includes, in addition, those over the greater range of angle of attack, -18 degrees through 90 degrees. The results show that: (1) at angles of attack above maximum lift, the biplane upper wing pressures are decreased by the shielding action of the lower wing. (2) the burble of the biplane lower wing, with respect to the angle of attack, is delayed, due to the shielding action of the lower wing. (3) the center of pressure of the biplane upper wing (semispan) is, in general, displaced forward and outward with reference to that of the wing as a monoplane, while for the lower wing there is but slight difference for both conditions. (4) the overhanging portion of the upper wing is little affected by the presence of the lower wing.
The High-Lift Common Research Model (CRM-HL) is a product of the NASA Advanced Air Transport Technology (AATT) Project intended to study various high-lift aerodynamic phenomena including enhanced lift, acoustic noise generation, and optimum placement of leading and trailing-edge devices. The current study was conducted in the NASA Langley 14-by 22-Foot Subsonic Tunnel (14x22) for the purpose of evaluating enhanced lift through the use of active flow control (AFC). The current paper documents the effect of sweeping-jet actuation combined with steady blowing on a simplified high-lift configuration using unsteady pressure measurements. The time-series parameters for the measurements are documented as well as the data acquisition system used to acquire the data. An uncertainty analysis will be presented in order to document the system performance and provide an estimate of the data quality. Repeatability of the data will be shown along with trends associated with model angle of attack, and those associated with changes in the nozzle pressure ratio (NPR) of the AFC system.
An electro-optical spin measurement system for a spin model in a spin tunnel includes a radio controlled receiver/transmitter, targets located on the spin model, optical receivers mounted around the perimeter of the spin tunnel and the base of the spin tunnel for receiving data from the targets, and a control system for accumulating data from the radio controlled receiver and receivers. Six targets are employed. The spin model includes a fuselage, wings, nose, and tail. Two targets are located under the fuselage of the spin model at the nose tip and tail. Two targets are located on the side of the fuselage at the nose tip and tail, and a target is located under each wing tip. The targets under the fuselage at the nose tip and tail measure spin rate of the spin model, targets on the side of the fuselage at the nose tip and tail measure angle of attack of the spin model, and the targets under the wing tips measure roll angle of the spin model. Optical receivers are mounted at 90 degree increments around the periphery of the spin tunnel to determine angle of attack and roll angle measurements of the spin model. Optical receivers are also mounted at the base of the spin tunnel to define quadrant and position of the spin model and to determine the spin rate of the spin model.
Film-cooling tests, with water as the coolant, were made on an 80 deg total-angle cone in a Mach number 2 free jet at sea-level pressure. The tests were made at free-stream total temperatures from 1,500 deg R to 3,000 deg R and at free-stream Reynolds numbers per foot from 8 x 10(exp 6) to 3 x 10(exp 6). The tests showed that the downstream end of the model became very hot if the coolant rate was too small to cover the complete model with a water film. This water film was fairly symmetrical when the model was at zero angle of attack but was very asymmetrical when the model was at an angle of attack of 5 deg. A comparison with results of a previous transpiration-cooling test showed that, with water as the coolant, transpiration cooling was at least 2.5 times as efficient as the film cooling of the present tests.
This paper presents a preliminary study for the characterization of collection efficiency from icing tests conducted in the Icing Research Tunnel at NASA Glenn Research Center. A test method previously developed for measuring the attachment line maximum collection efficiency of a swept NACA 0012 airfoil model at zero angle of attack was applied to the leading-edge region of a 65%-scale version of the Common Research Model midspan wing section. A correlation for the stagnation line maximum collection efficiency as a function of the modified inertia parameter was obtained with LEWICE3D simulations utilizing a discrete number of drop diameters. It was then compared with the collection efficiency measurement data obtained in the IRT. For the experimental collection efficiency, two ice shape digitization procedures were utilized to extract 2-D chord-wise ice shape profiles, i.e., the Maximum Combined Cross Section or MCCS, and the Minimum Combined Cross Section or MinCCS, at selected span-wise locations from the 3-D scanned ice shapes. The preliminary result showed that the rime ice thickness method can be used to characterize the collection efficiency distribution, for conditions free of ice erosion, in the main ice shape region. However, a high-order statistical processing of the ice scan is needed for estimating the mean ice thickness in areas where feathers are prevalent. From the limited comparison of the experimental and LEWICE3D collection efficiency data in the CRM65 MS model leading edge area, it was shown that the attachment line maximum collection efficiency is reasonably estimated by the best curve-fit correlation in the range of modified inertia parameter tested. A tighter alignment control of the iced and cold clean model scans as well as the model angle of attack are needed to improve the comparison. Further evaluation of this correlation is recommended to assess its applicability for Common Research Model type swept wing icing scaling analysis.
The effects of wing-lower-surface dive-recovery flaps on the aero- dynamic characteristics of a transonic seaplane model and a transonic transport model having 40 deg swept wings have been investigated in the Langley 16-foot transonic tunnel. The seaplane model had a wing with an aspect ratio of 5.26, a taper ratio of 0.333, and NACA 63A series airfoil sections streamwise. The transport model had a wing with an aspect ratio of 8, a taper ratio of 0.3, and NACA 65A series airfoil sections perpendicular to the quarter-chord line. The effects of flap deflection, flap longitudinal location, and flap sweep were generally investigated for both horizontal-tail-on and horizontal-tail-off configurations. Model force and moment measurements were made for model angles of attack from -5 deg to 14 deg in the Mach number range from 0.70 to 1.075 at Reynolds numbers of 2.95 x 10(exp 6) to 4.35 x 10(exp 6). With proper longitudinal location, wing-lower-surface dive-recovery flaps produced lift and pitching-moment increments that increased with flap deflection. For the transport model a flap located aft on the wing proved to be more effective than one located more forward., both flaps having the same span and approximately the same deflection. For the seaplane model a high horizontal tail provided added effectiveness for the deflected-flap configuration.
The High-Lift Common Research Model (CRM-HL) is a product of the NASA Advanced Air Transport Technology (AATT) Project intended to study various high-lift aerodynamic phenomena including enhanced lift, acoustic noise generation, and optimum placement of leading and trailing-edge devices. The current study was conducted in the NASA Langley 14-by 22-Foot Subsonic Tunnel (14x22) for the purpose of evaluating enhanced lift through the use of active flow control (AFC). The current paper documents the effect of sweeping-jet actuation combined with steady blowing on a simplified high-lift configuration using unsteady pressure measurements. The time-series parameters for the measurements are documented as well as the data acquisition system used to acquire the data. An uncertainty analysis will be presented in order to document the system performance and provide an estimate of the data quality. Repeatability of the data will be shown along with trends associated with model angle of attack, and also those associated with changes in the nozzle pressure ratio (NPR) of the AFC system.
The transitional flight characteristics of a geometrically simplified Short Take-Off Vertical Landing (STOVL) aircraft configuration have been measured in the NASA Ames 7- by 10-Foot Wind Tunnel. The experiment is the first in a sequence of tests designed to provide detailed data for evaluating the capability of computational fluid dynamics methods to predict the important flow parameters for powered lift. The model consists of a 60 deg cropped delta wing platform, blended fuselage and two circular in-line jets that exit perpendicularly from the flat lower surface. The measured flows have a maximum freestream Mach number of 0.2. Model angle of attack is varied between -10 and +20 deg. The flow is ambient temperature in both jet exits and the nozzle pressure ratios are varied between 1 and 3. The data presented includes forces and moments, pressures measured at 281 surface pressure ports and the pressures of the jets. Measurements of the flow are also made in the tunnel test section upstream and downstream of the model and at the jet exits to guide boundary condition selection for the planned computations. Flow visualization and total pressure measurements in the jet plumes provide a description of the three-dimensional jet efflux flowfield.
The circular body configuration is a generic single- or multi-stage reusable Earth-to-orbit transport. A thick clipped-delta wing is the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center fin, wingtip fins, and a nose-mounted fin. The tests were conducted in the Langley Unitary Plan Wind Tunnel. The configuration is longitudinally stable about the estimated center of gravity of 0.72 body length up to a Mach number of about 3.0. Above Mach 3.0, the model is longitudinally unstable at low angles of attack but has a stable secondary trim point at angles of attack above 30 deg. The model has sufficient pitch control authority with elevator and body flap to produce stable trim over the test range. The model with the center fin is directionally stable at low angles of attack up to a Mach number of 3.90. The rudder-like surfaces on the tip fins and the all-movable nose fin are designed as active controls to produce artificial directional stability and are effective in producing yawing moment. The wing trailing-edge aileron surfaces are effective in producing rolling moment, but they also produce large adverse yawing moment.
The performance characteristics of a model VTOL lift-fan simulator installed in a two-dimensional wing are presented. The lift-fan simulator consisted of a 15-inch diameter fan driven by a turbine contained in the fan hub. The performance of the lift-fan simulator was measured in two ways: (1) the calculated momentum thrust of the fan and turbine (total thrust loading), and (2) the axial-force measured on a load cell force balance (axial-force loading). Tests were conducted over a wide range of crossflow velocities, corrected tip speeds, and wing angle of attack. A prediction modeling technique was developed to help in analyzing the performance characteristics of lift-fan simulators. A multiple linear regression analysis technique is presented which calculates prediction model equations for the dependent variables.
The low-speed aerodynamic performance characteristics of two advanced counterrotation pusher-propeller configurations with cruise design Mach numbers of 0.72 were investigated in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. The tests were conducted at Mach number 0.20, which is representative of the aircraft take/off/landing flight regime. The investigation determined the effect of nonuniform inflow on the propeller performance characteristics for several blade angle settings and a range of rotational speeds. The inflow was varied by yawing the propeller mode to angle-of-attack by as much as plus or minus 16 degrees and by installing on the counterrotation propeller test rig near the propeller rotors a model simulator of an aircraft engine support pylon and fuselage. The results of the investigation indicated that the low-speed performance of the counterrotation propeller configurations near the take-off target operating points were reasonable and were fairly insensitive to changes in model angle-of-attack without the aircraft pylon/fuselage simulators installed on the propeller test rig. When the aircraft pylon/fuselage simulators were installed, small changes in propeller performance were seen at zero angle-of-attack, but fairly large changes in total power coefficient and very large changes of aft-to-forward-rotor torque ratio were produced when the propeller model was taken to angle-of-attack. The propeller net efficiency, though, was fairly insensitive to any changes in the propeller flowfield conditions near the take-off target operating points.
The noise generated by supersonic-tip-speed propellers creates a cabin noise problem for future airplanes powered by these propellers. Noise of a number of propeller models were measured in the NASA Lewis 8- by 6-Foot Wind Tunnel with flow parallel to the propeller axis. In flight, as a result of the induced upwash from the airplane wing, the propeller is at an angle of attack with respect to the incoming flow. Therefore, the 10-blade SR-6 propeller was operated at angle of attack to determine its noise behavior. Higher blade passage tones were observed for the propeller operating at angle of attack in a 0.6 axial Mach number flow. The noise increase was not symmetrical, with one wall of the wind tunnel showing a larger noise increase than the other wall. No noise increase was observed at angle of attack in a 0.8 axial Mach number flow. For this propeller the dominance of thickness noise, which does not increase with angle of attack, explains the lack of noise increase at the higher 0.8 Mach number.
Laser-Doppler velocimetry and seven-hole probes were employed to map out the velocity and vorticity field along a plane downstream of a hemisphere-cylinder. Steady flow data were obtained over a fixed model at a range of angles of attack, as well as over a model pitching through ramp motions to a final angle of attack. Attention was focused on the dynamic development of induced vortex asymmetry. It was found that the wake develops first in a symmetric fashion and asymmetry is generated with some time delay.
Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.
Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.
Longitudinal and lateral stability data were obtained with the model out of and in ground effect over a moving ground plane for a range of model angles of attack and sideslip at various thrust coefficients. These data were taken primarily at thrust coefficients which simulate transition speeds on the airplane between hover and 200 knots. Some data, however, represent the effect of thrust deflection at speeds up to 350 knots. Also presented are the effects of control-surface deflections and interference between the jets and free stream.