Procedure Guide for the Multifunction Arc Jet Instrumentation and Computation (MAJIC) System
This document describes the policies and procedures that govern Multifunction Arc Jet Instrumentation and Computation (MAJIC) system.
S Eddlemon↗
SEARCH · Engineering Papers
Results for “arc jet”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Arc-jet tests of coated carbon-carbon materials
The testing of coated carbon-carbon materials at high temperature in a nonequilibrium arc-driven environment is examined. Material specimens were exposed to high energy supersonic air exhausting from the NASA-Ames Research Center's 20-MW arc-jet facility. The materials were heated to required temperatures with arc-heated air for specified lengths of time. A total of 23 models were tested in two groups. In the first group of 19 samples, there were several samples that survived low test conditions and several more that survived intermediate test conditions that provided surface temperatures up to 3850 deg Rankine, but none survived when the surface temperature exceeded 4000 deg Rankine. The last four test samples with their higher surface temperatures did not fully survive either if the survival criterion is that the material must be reusable after the test.
Sheldahl, Robert E.↗
Experimental ablation data obtained from MSC one megawatt arc jet tests on the Stanford Research Institute - NASA round robin ablation program
Ablation study data from various arc jet facilities
Tillian, D. J.↗
Arc Jet Screening Tests Of Phase 1 Orbiter Tile Repair Materials and Uncoated RSI High Temperature Emittance Measurements
Arc jet tests of candidate tile repair materials and baseline Orbiter uncoated reusable surface insulation (RSI) were performed in the Johnson Space Center's (JSC) Atmospheric Reentry Materials and Structures Evaluation Facility (ARMSEF) from June 23, 2003, through August 19, 2003. These tests were performed to screen candidate tile repair materials by verifying the high temperature performance and determining the thermal stability. In addition, tests to determine the surface emissivity at high temperatures and the geometric shrinkage of bare RSI were performed. In addition, tests were performed to determine the surface emissivity at high temperatures and the geometric shrinkage of uncoated RSI.
DelPapa, Steven V.↗
Simulation of the AFE mission heating in an arc-jet wind tunnel
A technique is presented for simulating a time-varying heating profile in an arc-jet wind tunnel and its application to the testing of a sapphire radiometer window assembly for the Aeroassist Flight Experiment (AFE). The AFE is an experimental mission designed to obtain as much data as possible relative to the aerodynamic and aerothermodynamic phenomena associated with aeroassisted maneuvering. The developed test procedure ensures satisfactory simulation by avoiding the thermal gradients of a step-function heat exposure by matching the heating/time values and by matching the integrated heat load. Furthermore, this is accomplished in a plasma stream in which enthalpy and pressure ensure a close approximation to the real flight environment.
Terrazas-Salinas, Imelda↗
Development of Langmuir and Spatially Resolved OES Diagnostics for Arc Jet Shock and Boundary Layer Measurements Relevant to Atmospheric Re-Entry Environments
The second-generation miniature Arc Jet Research Chamber (mARC) ground testing facility at NASA Ames requires physical characterization of its supersonic plasma flow to verify numerical models and material sample testing. Two types of plasma diagnostics will be utilized: Langmuir probes and optical emission spectroscopy (OES). Several single and triple Langmuir probes have been constructed and will be inserted parallel to the flow via a sweep arm to measure post-shock electron temperature and number density along radial profiles at different axial distances. Due to the high heat flux (200-3000 W/cm2) sweep durations are necessarily short (< 0.1 s). Measuring these properties near the probe surface provide characterization of the post-shock environment. This is an important metric for validating coupled CFD-material codes, and will provide insight into longstanding thermocouple anomalies attributed to charging of heatshield surfaces. An OES system has also been assembled to obtain spatially resolved density and temperature for various flow species. The system consists of a convex lens that forms an image of the plasma onto a 16-channel linear fiber array, which will simultaneously capture the spectra from sixteen different locations. The light emission from the plasma is then focused by a spherical mirror into a spectrometer and recorded with a camera. These measurements non-intrusively provide a new spatially resolved flow characterization capability. This will initially be used to resolve issues with shock radiation interference in pyrometer measurements of material surface temperature. The design of each diagnostic and any initial results will be discussed.
Ethan Main-Loam Leong↗
Demonstration of the feasibility of laser induced fluorescence for arc jet flow diagnostics
Laser Induced Fluorescence (LIF) studies are carried out on nitric oxide and oxygen molecules in the arc jet flows at the NASA Johnson Space Center Reentry Testing Facility. Measurements are taken in the free stream and from a blunt body shock layer. Tests are performed under different flow conditions to determine the feasibility and sensitivity of the LIF technique for various species. This is developed as a part of high enthalpy flow diagnostics and will be useful to elucidate the rotational and vibrational temperatures. Adequate sensitivity for the detection of O(2) and NO is demonstrated. Proposed improvements of the existing system are presented.
Arepalli, Sivaram↗
Application of Laser Induced Fluorescence for flow diagnostics in arc jets
Laser Induced Fluorescence (LIF) studies are carried out on copper atoms, nitric oxide and oxygen molecules in the arc jet flows at the NASA Johnson Space Center Reentry Simulation Testing Facility. Measurements are taken in the free stream and from a blunt body shock layer. Tests are performed under different flow conditions to determine the feasibility and sensitivity of the LIF technique for various species. The LIF technique is developed as a part of high enthalpy flow diagnostics and will be useful to elucidate the rotational and vibrational temperatures. Adequate sensitivity for the detection of O2 and NO is demonstrated. Preliminary experiments for temperature and velocity measurements using copper as a tracer material are shown to be a useful new application of the laser resonant Doppler scattering technique.
Arepalli, Sivaram↗
Measured and calculated spectral radiation from a blunt body shock layer in an arc-jet wind tunnel
Spectra of the shock layer radiation incident on the stagnation point of a blunt body placed in an arc-jet wind tunnel were measured over the wavelength range from 600 nm to 880 nm. The test gas was a mixture of 80 percent air and 20 percent argon by mass, and the run was made in a highly nonequilibrium environment. The observed spectra contained contributions from atomic lines of nitrogen, oxygen, and argon, of bound-free and free-free continua, and band systems of N2 and N2(+). The measured spectra were compared with the synthetic spectra, which were obtained through four steps: the calculation of the arc-heater characteristics, of the nozzle flow, of the blunt-body flow, and the nonequilibrium radiation processes. The results show that the atomic lines are predicted approximately correctly, but all other sources are underpredicted by orders of magnitude. A possible explanation for the discrepancy is presented.
Babikian, Dikran S.↗
Spectroscopic Diagnostics and an Arc Jet Heated Air Plasma
Spectral radiation measurements were made in the range of 200 to 900 nm across a section of the plenum of an arc jet wind tunnel using a series of optical fibers. The spectra contained line radiation from Oxygen and Nitrogen atoms and molecular radiation from N2(+), N2, and NO. Abel inversion technique is used to obtain radial distribution of the spectra. The analysis yielded radial profiles of the electronic excitation, vibrational and rotational temperatures of the flow field. Spectral fitting yielded branching ratios for different vibrational and rotational bands. Relatively mild flow conditions, i.e. enthalpy and mass flow rate, were used for prolonged measurements of up to and over two hours to establish the best experimental methods of temperature determinations. Signal to noise was improved by at least an order of magnitude enabling the molecular vibrational band heads of N2(+) (first negative system), N2 (second positive system), and NO (beta, gamma, delta, and epsilon systems) to be resolved in the lower ultraviolet wavelength regions. The increased signal to noise ratio also enabled partial resolution of the rotational lines of N2(+) and N2 in certain regions of minimal overlap. Comparison of the spectra with theoretical models such as the NEQAIR2 code are presented and show potential for fitting the spectra when reliable calibration is performed for the complete wavelength range.
Mack, Larry Howard, Jr.↗
Emission Spectroscopy and Radiometric Measurements in the NASA Ames IHF Arc Jet Facility
Plasma diagnostic measurement campaigns in the NASA Ames Interaction Heating Facility (IHF) have been conducted over the last several years with a view towards characterizing the flow in the arc jet facility by providing data necessary for modeling and simulation. Optical emission spectroscopy has been used in the plenum and in the free jet of the nozzle. Radiation incident over a probe surface has also been measured using radiometry. Plenum measurements have shown distinct radial profiles of temperature over a range of operating conditions. For cases where large amounts of cold air are added radially to the main arc-heated stream, the temperature profiles are higher by as much as 1500 K than the profiles assumed in flow simulations. Optical measurements perpendicular to the flow direction in the free jet showed significant contributions to the molecule emission through inverse pre-dissociation, thus allowing determination of atom number densities from molecular emission. This has been preliminarily demonstrated with the N2 1st Positive System. Despite the use of older rate coefficients, the resulting atom densities are reasonable and surprisingly close to flow predictions.
Winter, Michael W.↗
Big-data Efficient and Automated Science Transfer (BEAST): An Open-Source Software Architecture for Arc Jet Data Management, Modeling, and Automation
Big-data Efficient and Automated Science Transfer (BEAST) is a facility data management application developed for the NASA Ames arc jet facilities. The current decentralized data management practices limit statistical tracking, synchronization between video/time series, search capability, data throughput, and data processing speed/efficiency. Consequently, BEAST was developed to provide a new data infrastructure with streamlined data collection, processing, transfer, and analysis. This new framework also seeks to implement the FAIR principles of data stewardship: Findable, Accessible, Interoperable, and Reusable. The BEAST framework is based on a combination of the Python Django web framework and the Python data stack to provide a monolithic, open-source platform for data management, automation, and machine learning. This architecture was chosen for maintainability and scalability for a small, in-house development team. This paper will describe the application framework, deployment, and discuss the benefits and future plans for the system.
Data management↗
Ablation of carbonaceous materials in a hydrogen-helium arc-jet flow
The stagnation-point ablation rates of a graphite, a carbon-carbon composite, and four carbon-phenolic materials are measured in an arc-jet wind tunnel with a 50% hydrogen-50% helium mixture as the test gas. Flow environments are determined through measurements of static and impact pressures, heat-transfer rates to a calorimeter, and radiation spectra, and through numerical calculation of the flow through the wind tunnel, spectra, and heat-transfer rates. The environments so determined are: impact pressure approx. 3 atm, Mach number approx. 2.1, convective heat-transfer rate approx. 14 kw/sq cm, and radiative heat-transfer rate approx. 7 kw/sq cm in the absence of ablation. Ablation rates are determined from the measured rates of mass loss and recession of the ablation specimens. Compared with the predicted ablation rates obtained by running RASLE and CMA codes, the measured rates are higher by about 15% for all tested materials.
Park, C.↗
Ablation of carbonaceous materials in a hydrogen-helium arc-jet flow
The stagnation-point ablation rates of a graphite, a carbon-carbon composite, and four carbon-phenolic materials are measured in an arc-jet wind tunnel with a 50 percent hydrogen-50 percent helium mixture as the test gas. Flow environments are determined through measurements of static and impact pressures, heat-transfer rates to a calorimeter, and radiation spectra, and through numerical calculation of the flow through the wind tunnel, spectra, and heat-transfer rates. The environments so determined are: impact pressure approximately equal to 3 atm, Mach number approximately equal to 2.1, convective heat-transfer rate approximately equal to 14 kW/sq cm, and radiative heat-transfer rate approximately equal to 7 kW/sq cm in the absence of ablation. Ablation rates are determined from the measured rates of mass loss and recession of the ablation specimens. Compared with the predicted ablation rates obtained by running RASLE and CMA codes, the measured rates are higher by about 15 percent for all tested materials.
Park, C.↗
Validating Arc-jet Condition Targets Using Inverse 1D Material Response Models
Experiments were conducted using both the Interaction Heating Facility (IHF) and Aerodynamic Heating Facility (AHF), two hypersonic arc-jet facilities at NASA Ames. These tests were run to understand the material response of ablative thermal protection system materials by exposing them to high-enthalpy flows. Using thermocouple data from the materials, test conditions were inversely determined and compared with expected results from a one-dimensional model using facility target conditions; this allowed an approximate environmental scale factor to be determined and applied to more accurately predict material response in additional tests.
material response↗
Processing, Properties and Arc Jet Testing of HfB2/SiC
Contents include the following: Background on Ultra High Temperature Ceramics - UHTCs. Summary UNTC processing: power processing, scale-up. Preliminary material properties: mechanical, thermal. Arc jet testing: flat face models, cone models. Summary.
Johnson, Sylvia M.↗
Arc Jet Test and Analysis of Asbestos Free Solid Rocket Motor Nozzle Dome Ablative Materials
Asbestos free solid motor internal insulation samples were recently tested at the MSFC Hyperthermal Arc Jet Facility. Objectives of the test were to gather data for solid rocket motor analog characterization of ablative and in-depth thermal performance of rubber materials subject to high enthalpy/pressure flow conditions. Tests were conducted over a range of convective heat fluxes for both inert and chemically reactive sub-sonic free stream gas flow. Active instrumentation included use of total calorimeters, in-depth thermocouples, and a surface pyrometer for in-situ surface temperature measurement. Post-test sample forensics involved determination of eroded depth, charred depth, total sample weight loss, and documentation of the general condition of the eroded profile. A complete Charring Material Ablator (CMA) style aero thermal analysis was conducted for the test matrix and results compared to the measured data. In general, comparisons were possible for a number of the cases and the results show a limited predictive ability to model accurately both the ablative response and the in-depth temperature profiles. Lessons learned and modeling recommendations are made regarding future testing and modeling improvements that will increase understanding of the basic chemistry/physics associated with the complicated material ablation process of rubber materials.
Clayton, J. Louie↗
Radial Profiles of the Plasma Electron Characteristics in a 30 kW Arc Jet
The present effort aims to strengthen modeling work conducted at the NASA Ames Research Center by measuring the critical plasma electron characteristics within and slightly outside of an arc jet plasma column. These characteristics are intended to give physical insights while assisting in the formulation of boundary conditions to validate full scale simulations. Single and triple Langmuir probes have been used to achieve estimates of the electron temperature (T(sub e)), electron number density (n(sub e)) and plasma potential (outside of the plasma column) as probing location is varied radially from the flow centerline. Both the electron temperature and electron number density measurements show a large dependence on radial distance from the plasma column centerline with T(sub e) approx. = (3 - 12 eV and n(sub e) approx. = 10(exp 12) - 10(exp 14)/cu cm.
Codron, Douglas A.↗