Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “angle control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Low-speed wind tunnel experiments have been conducted to define methods for the manipulation of a generic fighter forebody's vortices in order to generate controlled yawing moments at high alpha. Attention is given to two vortex-control schemes: one involving independently controlled forebody tip strakes, and the other individually controlled blowing ports on the forebody. The most effective methods for forebody yawing-moment control were found to be the minimization of natural asymmetry with a pair of symmetrically mounted tip strakes, and the perturbation of the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗
NASA NTRSDate not supplied

Numerical Predictor-Corrector Based Guidance Scheme For Aero-Gravity Assist at Titan For Enceladus Missions

Aero-gravity assist is a spacecraft maneuver than can enable a vehicle to insert into an orbit of one planetary body using the atmosphere and gravity field of a secondary body, reducing the required propellant mass relative to a fully-propulsive orbit insertion. The Fully Numerical Predictor-Corrector Aerocapture Guidance algorithm was modified to work with a direct force control blunt body vehicle, executing an aero-gravity assist at Titan to enter a Saturnian orbit and conduct fly-by at Enceladus. Additionally, a proportional-integral-derivative controller was implemented to command sideslip angles for control of the orbital inclination. Numerical simulation showed the developed guidance scheme was capable of minimizing the energy and inclination error at atmospheric exit, allowing Saturnian moon tour trajectories and Enceladus exploration at a small delta-V cost, on the order of 100 m/s, in the nominal case.

Daniel Louis Engel↗
NASA NTRSDate not supplied

Numerical Predictor-Corrector Based Guidance Scheme For Aero-Gravity Assist at Titan For Enceladus Missions

Aero-gravity assist is a spacecraft maneuver than can enable a vehicle to insert into an orbit of one planetary body using the atmosphere and gravity field of a secondary body, reducing the required propellant mass relative to a fully-propulsive orbit insertion. The Fully Numerical Predictor-Corrector Aerocapture Guidance algorithm was modified to work with a direct force control blunt body vehicle, executing an aero-gravity assist at Titan to enter a Saturnian orbit and conduct fly-by at Enceladus. Additionally, a proportional-integral-derivative controller was implemented to command sideslip angles for control of the orbital inclination. Numerical simulation showed the developed guidance scheme was capable of minimizing the energy and inclination error at atmospheric exit, allowing Saturnian moon tour trajectories and Enceladus exploration at a small delta-V cost, on the order of 100 m/s, in the nominal case.

Daniel L. Engel↗
NASA NTRS1957

Flight Investigation at Low Angles of Attack to Determine the Longitudinal Stability and Control Characteristics of a Cruciform Canard Missile Configuration with a Low-Aspect-Ratio Wing and Blunt Nose at Mach Numbers from 1.2 to 2.1

A full- scale rocket-powered model of a cruciform canard missile configuration with a low- aspect - ratio wing and blunt nose has been flight tested by the Langley Pilotless Aircraft Research Division. Static and dynamic longitudinal stability and control derivatives of this interdigitated canard-wing missile configuration were determined by using the pulsed- control technique at low angles of attack and for a Mach number range of 1.2 to 2.1. The lift - curve slope showed only small nonlinearities with changes in control deflection or angle of attack but indicated a difference in lift- .curve slope of approximately 7 percent for the two control deflections of delta = 3.0 deg and delta= -0.3 deg . The large tail length of the missile tested was effective in producing damping in pitch throughout the Mach number range tested. The aerodynamic- center location was nearly constant with Mach number for the two control deflections but was shown to be less stable with the larger control deflection. The increment of lift produced by the controls was small and positive throughout the Mach number range tested, whereas the pitching moment produced by the controls exhibited a normal trend of reduced effectiveness with increasing Mach number.The effectiveness of the controls in producing angle of attack, lift, and pitching moment was good at all Mach numbers tested.

Brown, Clarence A , Jr↗
NASA NTRS1957

Flight Investigation at Low Angles of Attack to Determine the Longitudinal Stability and Control Characteristics of a Cruciform Canard Missile Configuration with a Low-Aspect-Ratio Wing and Blunt Nose at Mach Numbers from 1.2 to 2.1

A full-scale rocket-powered model of a cruciform canard missile configuration with a low-aspect-ratio wing and blunt nose has been flight tested by the Langley Pilotless Aircraft Research Division. Static and dynamic longitudinal stability and control derivatives of this interdigitated canard-wing missile configuration were determined by using the pulsed-control technique at low angles of attack and for a Mach number range of 1.2 to 2.1. The lift-curve slope showed only small nonlinearities with changes in control deflection or angle of attack but indicated a difference in lift-curve slope of approximately 7 percent for the two control deflections of delta = 3.0 deg and delta = -0.3 deg. The large tail length of the missile tested was effective in producing damping in pitch throughout the Mach number range tested. The aerodynamic-center location was nearly constant with Mach number for the two control deflections but was shown to be less stable with the larger control deflection. The increment of lift produced by the controls was small and positive throughout the Mach number range tested, whereas the pitching moment produced by the controls exhibited a normal trend of reduced effectiveness with increasing Mach number. The effectiveness of the controls in producing angle of attack, lift, and pitching moment was good at all Mach numbers tested.

Brown, C. A., Jr.↗
NASA NTRS1992

Approaches to control of the large angle magnetic suspension test fixture

The Large Angle Magnetic Suspension Test Fixture is a five degree-of-freedom system, developed and built at NASA Langley Research Center. It is intended for study of control techniques in magnetic suspension systems with large angular capabilities. In this study, steps have been taken to prove the system in practice, using the existing hardware. A classical control approach, using dual phase advance compensators, is applied in simulation and hardware. A single decoupled degree-of-freedom of the system is stabilized and controlled in simulation. The procedure is then employed for all five degrees-of-freedom. The design and implementation of an analog and a digital controller are described. Results from simulation and the actual system are compared and analyzed. The ability to the system to sustain suspension over a large angular range has been proven in hardware.

Ghofrani, Mehran↗
NASA NTRS1986

Elastic robot control - Nonlinear inversion and linear stabilization

An approach to the control of elastic robot systems for space applications using inversion, servocompensation, and feedback stabilization is presented. For simplicity, a robot arm (PUMA type) with three rotational joints is considered. The third link is assumed to be elastic. Using an inversion algorithm, a nonlinear decoupling control law u(d) is derived such that in the closed-loop system independent control of joint angles by the three joint torquers is accomplished. For the stabilization of elastic oscillations, a linear feedback torquer control law u(s) is obtained applying linear quadratic optimization to the linearized arm model augmented with a servocompensator about the terminal state. Simulation results show that in spite of uncertainties in the payload and vehicle angular velocity, good joint angle control and damping of elastic oscillations are obtained with the torquer control law u = u(d) + u(s).

Singh, S. N.↗
NASA NTRS1985

Robust torque control of an elastic robotic arm based on invertibility and feedback stabilization

An approach to the control of elastic robotic systems for space applications using inversion, servocompensation, and feedback stabilization is presented. For simplicity, a robot arm (PUMA-type) with three rotational joints is considered. The third link is assumed to be elastic. Using an inversion algorithm, a nonlinear decoupling control law, u sub d, is derived such that in the closed loop system, independent control of joint angles by the three joint torquers is accomplished. For the stabilization of elastic oscillations, a linear feedback torquer control law, u sub s, is obtained applying linear quadratic optimization to the linearized arm model augmented with a servocompensator about the terminal state. Simulation results show that, in spite of uncertainties in the payload and vehicle angular velocity, good joint angle control and damping of elastic oscillations are obtained with the torquer control law u = u sub d + u sub s.

Singh, S. N.↗
NASA NTRS1992

Pitch Control Margin at High Angle of Attack - Quantitative Requirements (Flight Test Correlation With Simulation Predictions)

Aircraft designs that employ relaxed static stability (RSS) have the following problem: reduced pitching moments associated with RSS at high angle of attack (AOA) require a minimum pitch recovery moment or margin to guarantee a safe return from high AOA maneuvers at the most aft center of gravity (CG) encountered during a mission. Recent incidents and mishaps on Class IV aircraft have demonstrated a need for establishing quantitative longitudinal high AOA pitch control margin design guidelines for future aircraft. The Naval Air Warfare Center - Aircraft Division (NA WC-AD) is currently supporting an effort in conjunction with NASA Langley Research Center (NASA LaRC) to quantify such requirements. NASA LaRC has conducted a series of extensive simulation evaluations to define these design guidelines. The purpose of flight tests were to validate the overall research test methodology by comparing pilot comments, pilot ratings, and aircraft response characteristics gathered during inflight recoveries from high AOA conditions to those gathered during the fixed-base simulation sessions. Tests were completed on an F/A-18A in six flights for a total of 9.8 flight hours using an AOA and CG buildup sequence. Flight test results have validated the simulation studies in that pilot rating of high AOA nose-down recoveries were based on the short-term response interval in the forms of pitch acceleration and rate. In addition, flight test has demonstrated that high AOA pitch control margin can be evaluated using a stabilized pushover method.

Flight Testing↗
NASA NTRS1990

Experimental study on direct adaptive control of a PUMA 560 industrial robot

The implementation and experimental validation of a direct adaptive control scheme on a PUMA 560 industrial robot is discussed. The design theory for direct adaptive control of manipulators is outlined and the test facility and software are described. Results are presented from the experiments on the simultaneous control of all of the six joint angles and control of the end-effector position and orientation of the robot. Also, the possible applications of the direct adaptive control scheme are considered.

Seraji, H.↗
NASA NTRS2009

Axial and Centrifugal Compressor Mean Line Flow Analysis Method

This paper describes a method to estimate key aerodynamic parameters of single and multistage axial and centrifugal compressors. This mean-line compressor code COMDES provides the capability of sizing single and multistage compressors quickly during the conceptual design process. Based on the compressible fluid flow equations and the Euler equation, the code can estimate rotor inlet and exit blade angles when run in the design mode. The design point rotor efficiency and stator losses are inputs to the code, and are modeled at off design. When run in the off-design analysis mode, it can be used to generate performance maps based on simple models for losses due to rotor incidence and inlet guide vane reset angle. The code can provide an improved understanding of basic aerodynamic parameters such as diffusion factor, loading levels and incidence, when matching multistage compressor blade rows at design and at part-speed operation. Rotor loading levels and relative velocity ratio are correlated to the onset of compressor surge. NASA Stage 37 and the three-stage NASA 74-A axial compressors were analyzed and the results compared to test data. The code has been used to generate the performance map for the NASA 76-B three-stage axial compressor featuring variable geometry. The compressor stages were aerodynamically matched at off-design speeds by adjusting the variable inlet guide vane and variable stator geometry angles to control the rotor diffusion factor and incidence angles.

Veres, Joseph P.↗
NASA NTRS1984

Low-speed wind-tunnel study of the high-angle-of-attack stability and control characteristics of a cranked-arrow-wing fighter configuration

The low-speed, high-angle-of-attack stability and control characteristics of a fighter configuration incorporating a cranked arrow wing were investigated in the Langley 30- by 60-foot tunnel as part of a NASA/General Dynamics cooperative research program to investigate the application of advanced wing designs to combat aircraft. Tests were conducted on a baseline configuration and on several modified configurations. The results show that the baseline configuration exhibited a high level of maximum lift but displayed undesirable longitudinal and lateral-directional stability characteristics at high angles of attack. Various wing modifications were made which improved the longitudinal and lateral-directional stability characteristics of the configuration at high angles of attack. However, most of the modifications were detrimental to maximum lift.

Grafton, S. B.↗
NASA NTRS1994

Some further developments in the dynamic modelling and control of the large angle magnetic suspension test fixture

A small-scale laboratory magnetic suspension system, the Large Angle Magnetic Suspension Test Fixture (LAMSTF) has been constructed at NASA Langley Research Center. This paper first presents some recent developments in the mathematical modelling of the system, particularly in the area of eddy current effects. It is shown that these effects are significant, but may be amenable to modelling and measurement. Next, a theoretical framework is presented, together with a comparison of computed and experimental data. Finally, some control aspects are discussed, together with illustration that the major design objective of LAMSTF - a controlled 360 deg rotation about the vertical axis, has been accomplished.

Britcher, Colin P.↗
DOE OSTI2024

Select Proliferation Studies on TRISO-fueled, Heat-Pipe-cooled Microreactors

Nuclear microreactors carry the potential to open up new markets for the nuclear industry, as their expected cost competitiveness in non-traditional market segments (e.g., mines, military bases, extraterrestrial surfaces, and remote areas), and their inherent safety features make them deployable when other power sources are unavailable or difficult to exploit. For countries that have not traditionally participated in nuclear power, microreactors represent a clean energy solution [1]. However, their use, especially in non-weapons states, may entail challenges in terms of maintaining international nuclear safeguards [2]. Furthermore, the deployment locations where microreactors may prove most cost competitive would be difficult to access by state and International Atomic Energy Agency (IAEA) inspectors [3]. In addition to the isolated nature of potential deployment sites, the low-power characteristic of microreactors suggests that numerous microreactors would need to be deployed to meet energy demands. That, coupled with the unique physics of many current microreactor designs, opens up a new area of research with respect to nonproliferation and safeguards concerns [2]. Whereas traditional facilities are inspected as isolated cases when looking for signs of diversion or misuse; microreactors may need to be assessed in the context of the entire fleet to which they belong. International safeguards necessitate timely detection of any significant quantities (SQs) of material that are being diverted (e.g., 1 SQ of special nuclear material diverted over the course of a 1-year period) [4]. For low-enriched uranium, the IAEA defines 1 SQ as corresponding to 75 kg of 235U. The purpose of the present paper is to explore the detectability threshold for material diversion in microreactors by relying on critical control drum angles, excess reactivity, and the reactor lifetime as the selected operational parameters. For this assessment, a heat-pipe-cooled microreactor was regarded as the base design. While the conclusions reached in this paper are not readily extendable to the design of actual microreactors, the analysis herein enables conclusions to be drawn regarding the level of accuracy needed for reference calculations in order to detect diversion scenarios by utilizing the selected operational parameters (i.e., mainly control drum angles, critical insertion angle, and the reactor lifetime).

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1978

Control of wind turbine generators connected to power systems

A unique simulation model based on a Mode-O wind turbine is developed for simulating both speed and power control. An analytical representation for a wind turbine that employs blade pitch angle feedback control is presented, and a mathematical model is formulated. For Mode-O serving as a practical case study, results of a computer simulation of the model as applied to the problems of synchronization and dynamic stability are provided. It is shown that the speed and output of a wind turbine can be satisfactorily controlled within reasonable limits by employing the existing blade pitch control system under specified conditions. For power control, an additional excitation control is required so that the terminal voltage, output power factor, and armature current can be held within narrow limits. As a result, the variation of torque angle is limited even if speed control is not implemented simultaneously with power control. Design features of the ERDA/NASA 100-kW Mode-O wind turbine are included.

Hwang, H. H.↗
NASA NTRS1933

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack V : spoilers and ailerons on rectangular wings

This report covers the fifth of a series of systematic investigations in which lateral control devices are compared with particular reference to their effectiveness at high angles of attack. The present report deals with tests of spoilers and ordinary ailerons on rectangular Clark y wing models. In an effort to obtain satisfactory control throughout the entire angle-of-attack range that can be maintained in flight, various spoilers were tested in combination with two sizes of previously tested ordinary ailerons - one of average proportions and the other short and wide. In addition, one large spoiler was tested alone. It was found that when ailerons and spoilers are used together the full effect of both is not obtained if the spoilers are located directly in front of the ailerons. With the proper combination of spoiler and aileron, however, it is possible to obtain satisfactory rolling control up to high angles of attack (15 degrees to 20 degrees), together with favorable yawing moments and small control forces. A moderate amount of rolling control with favorable yawing moments and small control forces was obtained with the large spoiler alone.

Weick, Fred E↗
NASA NTRS1994

Flight validation of ground-based assessment for control power requirements at high angles of attack

A review is presented in viewgraph format of an ongoing NASA/U.S. Navy study to determine control power requirements at high angles of attack for the next generation high-performance aircraft. This paper focuses on recent flight test activities using the NASA High Alpha Research Vehicle (HARV), which are intended to validate results of previous ground-based simulation studies. The purpose of this study is discussed, and the overall program structure, approach, and objectives are described. Results from two areas of investigation are presented: (1) nose-down control power requirements and (2) lateral-directional control power requirements. Selected results which illustrate issues and challenges that are being addressed in the study are discussed including test methodology, comparisons between simulation and flight, and general lessons learned.

Ogburn, Marilyn E.↗