Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “absorption coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Thickness-dependent dispersion parameters, energy gap and nonlinear refractive index of ZnSe thin films

Highlights: • Combined experimental and theoretical researches on ZnSe Thin Films. • The film thickness and refractive index were determined using envelope method. • The absorption coefficient and the energy gap were calculated. • Dispersion parameters were determined using Wemple-DiDomenico relation. • The third order susceptibility and nonlinear refractive index were calculated. - Abstract: Zinc selenide (ZnSe) thin films with different thicknesses were evaporated onto glass substrates using the thermal evaporation technique. X-ray diffraction analysis confirmed that both the film and powder have cubic zinc-blende structure. The fundamental optical parameters like absorption coefficient, extinction coefficient and band gap were evaluated in transparent region of transmittance and reflectance spectrum. The optical transition of the films was found to be allowed, where the energy gap increased from 2.576 to 2.702 eV with increasing film thickness. Also, the refractive index value increase with increasing film thickness. The refractive indices evaluated through envelope method were extrapolated by Cauchy dispersion relationship over the whole spectra range. Additionally, the dispersion of refractive index was determined in terms of Wemple-DiDomenico single oscillator model. Third order susceptibility and nonlinear refractive index were determined for different thickness of ZnSe thin films.

36 MATERIALS SCIENCE↗

Gamma ray irradiation-induced variations in structure and optical properties of cerium/titanium-doped oxyfluoride transparent glass-ceramics

Highlights: • CeO{sub 2} favors CaF{sub 2} crystallization while TiO{sub 2} suppresses CaF{sub 2} crystallization. • Doping TiO{sub 2} helps reduce intrinsic coloring caused by CeO{sub 2}. • Doping CeO{sub 2} and/or TiO{sub 2} improves defects saturation over irradiation does. • Doping CeO{sub 2} allows lower radiation induced absorption coefficient than co-doping CeO{sub 2}/TiO{sub 2}. - Abstract: CeO{sub 2}/TiO{sub 2}-doped oxyfluoride transparent glass ceramics with a composition of 45SiO{sub 2}–20Al{sub 2}O{sub 3}–10CaO–25CaF{sub 2} were synthesized and irradiated by gamma ray. The effects of CeO{sub 2}/TiO{sub 2} on the structure and optical properties of the samples before and after irradiation were investigated. Doping with CeO{sub 2} causes network depolymerization and conversion of [AlO{sub 6}] to [AlO{sub 4}], enlarging the percolation region and promoting CaF{sub 2} crystallization. Co-doping with CeO{sub 2}/TiO{sub 2} helps reduce the intrinsic coloring of transparent glass ceramics containing only CeO{sub 2}, and the addition of TiO{sub 2} enhances network interconnectivity, suppressing CaF{sub 2} crystallization. Doping with CeO{sub 2} and/or TiO{sub 2} improves the structural stability of transparent glass ceramics upon irradiation and maintains the optical band gap and Urbach energy constant due to the defect saturation over the irradiation dose. Doping solely with CeO{sub 2} allows for a lower radiation-induced absorption coefficient than co-doping CeO{sub 2}/TiO{sub 2} because of the enhanced crystallization induced by CeO{sub 2} and balanceable light absorption of polyvalent cerium ions.

36 MATERIALS SCIENCE↗

Dynamics of Electronic States and Magnetoabsorption in 3D Topological Insulators in a Quantizing Magnetic Field

Quantum states have been calculated analytically; the dynamics of a wave packet in a magnetic field has been investigated, and the optical absorption coefficient has been calculated for surface states in 3D topological insulators of the Bi{sub 2}Te{sub 3} family. We have detected a qualitative effect of the hexagonal warping of the spectrum on the structure of wavefunctions at the Landau levels, its manifestation in the features of the wave packet dynamics in a quantizing magnetic field, as well as in the frequency dependence of the optical absorption coefficient, in which new peaks that are absent in the isotropic model of the spectrum appear depending on the polarization of the incident wave. The effects considered here can be manifested in the optical and transport experiments with topological insulators, which makes it possible to determine the parameters of their band structure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Light Absorption by Brown Carbon over the South-East Atlantic Ocean

Biomass burning emissions often contain brown carbon (BrC), which represents a large family of light-absorbing organics that is chemically complex and therefore difficult to estimate their absorption of incoming solar radiation, resulting in large uncertainties in the estimation of the global direct radiative effect of aerosols. Here we investigate the contribution of BrC to the total light absorption of biomass burning aerosols over the South-East Atlantic Ocean with different optical models utilizing a suite of airborne measurements from the ORACLES 2018 campaign by introducing an effective refractive index of black carbon (BC), m eBC = n eBC +ik eBC , that accounts for all possible absorbing components at 660 nm wavelength to facilitate the attribution of absorption at shorter wavelengths. Most values of the imaginary part of the refractive index, k eBC , were larger than those commonly used for BC from biomass burning emissions, suggesting contributions from absorbers beyond BC at 660 nm. The TEM-EDX single particle analysis further suggests that these long-wavelength absorbers might include iron oxides, as iron is found to be present only when large values of k eBC are derived. Using this effective BC refractive index, we find that the contribution of BrC to the total absorption at 470 nm (R BrC,470 ) ranges from ~5–15 %, with the organic aerosol mass absorption coefficient (MAC OA,470 ) at this wavelength ranging from 0.25 ± 0.34 m 2 g -1 to 0.43 ± 0.12 m 2 g -1 . The core-shell model yielded much higher estimates of MAC OA,470 and R BrC,470 than homogeneous mixing models, underscoring the importance of model treatment. Another key finding was that estimates of the BrC contribution at 470 nm from the commonly used AAE (absorption Ångström exponent) attribution method (< 5 %) are much lower than the BrC contribution estimates (R BrC,470 ) using our new methodology that accounts for contributions from both BrC and non-carbonaceous, long-wavelength absorbers, such as magnetite. Thus, it is recommended that application of any optical properties-based attribution method use absorption coefficients at the longest possible wavelength to minimize the influence of BrC at the long wavelength and to account for potential contributions from other absorbing materials.

54 ENVIRONMENTAL SCIENCES↗

Optical anisotropy of InAs/GaSb broken-gap quantum wells

We investigate in detail the optical anisotropy of absorption of linearly polarized light in InAs/GaSb quantum wells grown on GaSb along the [001] direction, which can be used as an active region of different laser structures. The energy level positions, the wave functions, the optical matrix elements, and the absorption coefficients are calculated using the eight-band k {center_dot} p model and the Burt-Foreman envelope function theory. In these calculations, the Schroedinger and Poisson equations are solved self-consistently taking the lattice-mismatched strain into account. We find that a realistic Hamiltonian, which has the C{sub 2v} symmetry, results in considerable anisotropy of optical matrix elements for different directions of light polarization and different directions of the initial-state in-plane wave vector, including low-symmetry directions. We trace how the optical matrix elements and absorption are modified when spin-orbit interaction and important symmetry breaking mechanisms are taken into account (structural inversion asymmetry, bulk inversion asymmetry, and interface Hamiltonian). These mechanisms result in an almost 100% anisotropy of the absorption coefficients as the light polarization vector rotates in the plane of the structure and in a plane normal to the interfaces.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Low-temperature atomic layer deposition of CuSbS 2 for thin-film photovoltaics

Copper antimony sulfide (CuSbS 2 ) has been gaining traction as an earth-abundant absorber for thin-film photovoltaics given its near ideal band gap for solar energy conversion (~1.5 eV), large absorption coefficient (>10 4 cm –1 ), and elemental abundance. Through careful in situ analysis of the deposition conditions, a low-temperature route to CuSbS 2 thin films via atomic layer deposition has been developed. After a short (15 min) post process anneal at 225 °C, the ALD-grown CuSbS 2 films were crystalline with micron-sized grains, exhibited a band gap of 1.6 eV and an absorption coefficient >10 4 cm –1 , as well as a hole concentration of 10 15 cm –3 . Finally, the ALD-grown CuSbS 2 films were paired with ALD-grown TiO 2 to form a photovoltaic device. This photovoltaic device architecture represents one of a very limited number of Cd-free CuSbS 2 PV device stacks reported to date, and it is the first to demonstrate an open-circuit voltage on par with CuSbS 2 /CdS heterojunction PV devices. As a result, while far from optimized, this work demonstrates the potential for ALD-grown CuSbS 2 thin films in environmentally benign photovoltaics.

36 MATERIALS SCIENCE↗

AlSb as a material for high index contrast nanophotonics

High contrast materials, i.e., materials with a high refractive index and low optical loss, are of wide interest for nanophotonics and metasurface designs at optical and near infrared wavelengths. We explore aluminum antimonide (AlSb) as a high contrast nanophotonic material, using the design of high contrast gratings (HCGs) for low loss dielectric mirrors as an example. The high index of refraction and low absorption coefficient of AlSb in the visible wavelength range enable designs of HCGs that can be effectively optimized to form mirrors with 93.5% reflectivity at red visible wavelengths. We detail a co-sputtering synthesis method for AlSb films, and achieve our target high index of refraction of 3.5 for 635 nm light. We also find that the high sensitivity of AlSb oxidation requires specific handling procedures in developing deposition processes to yield a near zero absorption coefficient.

Bauser, Haley C.↗

Crystal-field effects in fluoride crystals for optical refrigeration

The field of optical refrigeration of rare-earth-doped solids has recently seen an important breakthrough. The cooling of a YLiF{sub 4} (YLF) crystal doped with 5 mol% Yb3+ to 155 K by Seletskiy et al [NPhot] has surpassed the lowest temperatures ({approx}170 K for {approx}100 mW cooling capacity) that are practical with commercial multi-stage thermoelectric coolers (TEC) [Glaister]. This record performance has advanced laser cooling into an application relevant regime and has put first practical optical cryocoolers within reach. The result is also relevant from a material perspective since for the first time, an Yb3+-doped crystal has outperformed an Yb3+-doped glass. The record temperature of 208 K was held by the Yb3+-doped fluorozirconate glass ZBLAN. Advanced purification and glass fabrication methods currently under development are expected to also advance ZBLAN:Yb3+ to sub-TEC temperatures. However, recent achievements with YLF:Yb3+ illustrate that crystalline materials may have two potentially game-changing advantajes over glassy materials. First, the crystalline environment reduces the inhomogeneous broadening of the Yb3+ electronic transitions as compared to a glassy matrix. The respective sharpening of the crystal-field transitions increases the peak absorption cross section at the laser excitation wavelength and allows for more efficient pumping of the Yb3+ ions, particularly at low temperatures. Second, many detrimental impurities present in the starting materials tend to be excluded from the crystal during its slow growth process, in contrast to a glass where all impurities present in the starting materials are included in the glass when it is formed by temperature quenching a melt. The ultra high purity required for laser cooling materials [PRB] therefore may be easier to realize in crystals than in glasses. Laser cooling occurs by laser excitation of a rare-earth ion followed by anti-Stokes luminescence. Each such laser-cooling cycle extracts thermal energy from the solid and carries it away as high-entropy light, thereby cooling the material. In the ideal case, the respective laser-cooling power is given by the pump wavelength ({lambda}{sub p}), the mean fluorescence wavelength ({bar {lambda}}{sub L}), and the absorption coefficient (a{sub r}) of the pumped transition. These quantities are solely determined by crystal field interactions. On one hand, a large crystal-field splitting offers a favorably large difference of {lambda}{sub p} - {bar {lambda}}{sub L} and thus a high cooling efficiency {eta}{sub cool} = ({lambda}{sub p} - {bar {lambda}}{sub L})/{bar {lambda}}{sub L}. On the other hand, a small crystal-field splitting offers a high thermal population (n{sub i}) of the initial state of the pumped transition, giving a high pump absorption coefficient and thus high laser cooling power, particularly at low temperatures. A quantitative description of crystal-field interactions is therefore critical to the understanding and optimization of optical refrigeration. In the case of Yb3+ as the laser cooling ion, however, development of a crystal-field model is met with substantial difficulties. First, Yb3+ has only two 4/multiplets, {sup 2}F{sub 7/2} and {sup 2}F{sub 5/2}, which lead to at most 7 crystal-field levels. This makes it difficult, and in some cases impossible, to evaluate the crystal-field Hamiltonian, which has at least 4 parameters for any Yb3+ point symmety lower than cubic. Second, {sup 2}F{sub 7/2}{leftrightarrow}{sup 2}F{sub 5/2} transitions exhibit an exceptionally strong electron-phonon coupling compared to 4f transitions of other rare earths. This makes it difficult to distinguish electronic from vibronic transitions in the absorption and luminescence spectra and to reliably identify the crystal-field levels. Yb3+ crystal-field splittings reported in the literature should thus generally be viewed with caution. This paper explores the effects of crystal-field interactions on the laser cooling performance of Yb3+-doped fluoride crystals. It is shown that the total crystal-field splitting of the {sup 2}F{sub 7/2} and {sup 2}F{sub 5/2} multiplets of Yb3+ can be estimated from crystal-field splittings of other rare-earth-doped fluoride crystals. This approach takes advantage of an extensive body of experimental work from which Yb3+ doped fluoride crystals with favorable laser cooling properties might be identified. Section 2 reviews the crystal-field splitting of the 4f electronic states and introduces the crystal-field strength as a means to predict the total crystal-field splitting of the {sup 2}F{sub 7/2} and {sup 2}F{sub 5/2} multiplets. Section 3 illustrates the effect of the total {sup 2}F{sub 7/2} crystal field splitting on the laser cooling power. Finally, Section 4 compiles literature data on crystal-field splittings in fluoride crystals from which the {sup 2}F{sub 7/2} splitting is predicted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimal absorber thickness in long-wave multiple-stage detector

The detectivity characteristics of interband cascade infrared type-II superlattice detectors for long-wave infrared detection (λ{sub cut-off} = 8 μm at room temperature) are discussed. We present comparison of two superlattices: InAs/GaSb and InAs/InAsSb, assuming the characteristic parameters—absorption coefficients α and carrier lifetimes τ published in literature. Dependence of the Johnson-noise limited detectivity on the absorber thickness for a different number of stages is reported. Higher detectivity D{sup *} value can be achieved by increasing the carrier lifetime. However, for detectors based on type-II InAs/GaSb superlattice increasing the carrier lifetime up to 25 ns leads to a situation in which one stage is preferred, i.e. for detector with a single absorber, we obtain the highest detectivity value. In the case of InAs/InAsSb material, the situation is similar for τ ≥ 80 ns. We have shown that the optimal absorber thickness at which the highest detectivity values are obtained depends not only on the absorption coefficient α and the number of stages N{sub S}, but also on the carrier diffusion length L. According to a calculations, cascade detectors based on Ga-free material should have much higher optimal absorber thicknesses than materials based on InAs/GaSb.

42 ENGINEERING↗

Validating plastic scintillation detectors for photon dosimetry in the radiologic energy range

Purpose: Photon dosimetry in the kilovolt (kV) energy range represents a major challenge for diagnostic and interventional radiology and superficial therapy. Plastic scintillation detectors (PSDs) are potentially good candidates for this task. This study proposes a simple way to obtain accurate correction factors to compensate for the response of PSDs to photon energies between 80 and 150 kVp. The performance of PSDs is also investigated to determine their potential usefulness in the diagnostic energy range. Methods: A 1-mm-diameter, 10-mm-long PSD was irradiated by a Therapax SXT 150 unit using five different beam qualities made of tube potentials ranging from 80 to 150 kVp and filtration thickness ranging from 0.8 to 0.2 mmAl + 1.0 mmCu. The light emitted by the detector was collected using an 8-m-long optical fiber and a polychromatic photodiode, which converted the scintillation photons to an electrical current. The PSD response was compared with the reference free air dose rate measured with a calibrated Farmer NE2571 ionization chamber. PSD measurements were corrected using spectra-weighted corrections, accounting for mass energy-absorption coefficient differences between the sensitive volumes of the ionization chamber and the PSD, as suggested by large cavity theory (LCT). Beam spectra were obtained from x-ray simulation software and validated experimentally using a CdTe spectrometer. Correction factors were also obtained using Monte Carlo (MC) simulations. Percent depth dose (PDD) measurements were compensated for beam hardening using the LCT correction method. These PDD measurements were compared with uncorrected PSD data, PDD measurements obtained using Gafchromic films, Monte Carlo simulations, and previous data. Results: For each beam quality used, the authors observed an increase of the energy response with effective energy when no correction was applied to the PSD response. Using the LCT correction, the PSD response was almost energy independent, with a residual 2.1% coefficient of variation (COV) over the 80-150-kVp energy range. Monte Carlo corrections reduced the COV to 1.4% over this energy range. All PDD measurements were in good agreement with one another except for the uncorrected PSD data, in which an over-response was observed with depth (13% at 10 cm with a 100 kVp beam), showing that beam hardening had a non-negligible effect on the PSD response. A correction based on LCT compensated very well for this effect, reducing the over-response to 3%.Conclusion: In the diagnostic energy range, PSDs show high-energy dependence, which can be corrected using spectra-weighted mass energy-absorption coefficients, showing no considerable sign of quenching between these energies. Correction factors obtained by Monte Carlo simulations confirm that the approximations made by LCT corrections are valid. Thus, PSDs could be useful for real-time dosimetry in radiology applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Te-doped perovskite NaTaO3 as a promising photocatalytic material for hydrogen production from water splitting driven by visible light

Highlights: • S, Se and Te-doped NaTaO{sub 3} is a promising material for photocatalytic water splitting. • Enhanced absorption coefficient in the visible light range is identified for Te-doped NaTaO{sub 3}. • Te-doped NaTaO{sub 3} exhibits higher electron and hole mobility than pristine NaTaO{sub 3}. - Abstract: The photocatalytic hydrogen production from water splitting can be achieved by using the pristine NaTaO{sub 3} experimentally, but the reaction cannot be driven by the visible light because of the wide band gap of NaTaO{sub 3}. The present work focuses on tuning the photocatalytic performance of NaTaO{sub 3} into the visible light range by doping S, Se, and Te elements. The obvious decrease in band energy gaps (E{sub g}s) and noticeable red-shift of the absorption edges are observed for the doped structures. The valence band maximum and conduction band minimum of the doped structures satisfy the requirement of the water splitting. Moreover, a significant enhancement of absorption coefficient in the visible light range is observed for the doped structure of Te@O. The calculated carrier mobility is used to evaluate the charge spatial separation of Te@O and the unusual increases and the obvious differences of the mobility of the electrons and holes are observed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

First principle study of structural, electronic, optical, and transport properties of ternary compounds NaGaX{sub 2} (X = S, Se, and Te) in tetragonal chalcopyrite phase

Eemploying the all electron full potential linearized augmented plane wave plus local orbital (FP-LAPW + lo) method based on density functional theory (DFT) structural, electronic, optical, and transport properties of compounds NaGaX{sub 2} (X = S, Se, and Te) in tetragonal phase have been investigated at ground state. The exchange-correlation effects have been included using the Wu Cohen (WC) generalized gradient approximation (GGA) and modified Becke–Johnson (mBJ) exchange potentials. Enthalpy of formation values ensure that crystal structures are stable in tetragonal chalcopyrite phase. Total and partial density of states, and band structures have been plotted to calculate electronic properties which exhibits direct band gap for all compounds. The electronic band gap of NaGaS{sub 2} (2.1 eV) is found to be higher than the electronic band gaps of NaGaSe{sub 2} (1.7 eV) and NaGaTe{sub 2} (1.2 eV) compounds. Using real and imaginary parts of the dielectric function, optical properties such as refractive index (n), extinction coefficient (k), reflectivity (R), absorption coefficient (α), and energy loss spectrum (L) were determined. Transport properties like Seebeck coefficient, thermal and electrical conductivities, figure of merit, and power factors have also been reported by combining the results from DFT and Boltzmann transport theory. The high absorption peaks in visible and ultraviolet regions of the energy spectrum and direct band gaps of these compounds ensure that three compounds are promising materials for photovoltaic applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A novel energy balance approach for a verifiable and accurate solution of radiation extinction in purely absorbing particle clouds

Here we consider the problem of radiation transport through purely absorbing particle clouds. The gold-standard solution of particle-resolved Monte Carlo ray-tracing method to this problem is computationally expensive and therefore solving the radiation transport equation (specifically, the Beer-Bouguer law (BB-law)) on a Eulerian mesh is often preferred. While the absorption coefficient in the real problem is infinite, the BB-law approximates it to be a finite number in the form of number density through a set of assumptions. For particle clouds that do not obey these assumptions, the BB-law predicts an incorrect exponential decay. Also, when the number density is computed using the nearest-neighbor approach, the BB-law solution diverges when the Eulerian mesh size becomes closer to or smaller than the particle size. This numerical divergence is due to the homogenization error. Although the filtering strategy for number density minimizes the homogenization error, it still converges to an incorrect exponential decay for particle clouds that break the BB-law constraints and the cost of the filtering is equivalent to that of the gold-standard solution. In this study, we develop a novel, highly accurate, verifiable and cost-effective solution to the radiation transport equation on a Eulerian domain using an energy balance approach where we derive an expression for the absorption coefficient as a function of particle and Eulerian mesh sizes. We apply our new method to Poisson and turbulent particle clouds that violate all the BB-law constraints and show that the solution is converging upon the mesh refinement, and eventually, we recover the same gold-standard solution for a much cheaper computational cost.

42 ENGINEERING↗

Crystalline Silicon Solar Cells

Most solar cells are fabricated from crystalline or semicrystalline silicon since they are relatively inexpensive starting materials and the resulting solar cells are very efficient. As a result, the optical properties of silicon are extremely important in many aspects of solar cell manufacture, and have been determined by many groups using several techniques. The most reliable values of the optical functions of silicon have been determined using spectroscopic ellipsometry, augmented by optical transmission measurements of the absorption coefficient for wavelengths greater than 700 nm. Obviously, these optical functions depend on the wavelength of light, but they also depend significantly on temperature and morphology. Several thin films are very important to solar cell manufacture, including silicon nitride, silicon dioxide, and aluminum oxide. While the optical properties of these thin films are strong functions of deposition conditions, spectroscopic ellipsometry is ideal for characterizing them. This work will present recent spectroscopic ellipsometry data and optical transmission data from which the optical functions of silicon are obtained. The optical transmission data have been fit from 700 to 1200 nm to a modification of Macfarlane’s et al. formula [Phys. Rev. 111, (1958) 759], resulting in a reduced χ2 of 0.84. This formulation is particularly valuable in that it gives the optical absorption coefficient from 700 to 1200 nm as a function of both wavelength and temperature.

Jellison Jr, Gerald Earle↗

Phase identification and control of thin films deposited by co-evaporation of elemental Cu, Zn, Sn, and Se

Kesterite thin films [(i.e., Cu{sub 2}ZnSn(S,Se){sub 4} and related alloys] have been the subject of recent interest for use as an absorber layer for thin film photovoltaics due to their high absorption coefficient (>10{sup 4} cm{sup -1}), their similarity to successful chalcopyrites (like CuInxGa{sub 1-x}Se{sub 2}) in structure, and their earth-abundance. The process window for growing a single-phase kesterite film is narrow. In this work, we have documented, for our 9.15%-efficient kesterite co-evaporation process, (1) how appearance of certain undesirable phases are controlled via choice of processing conditions, (2) several techniques for identification of phases in these films with resolution adequate to discern changes that are important to device performance, and (3) reference measurements for those performing such phase identification. Data from x-ray diffraction, x-ray fluorescence, Raman scattering, scanning electron microscopy, energy dispersive spectroscopy, and current-voltage characterization are presented.

36 MATERIALS SCIENCE↗

Optical properties of InAsBi and optimal designs of lattice-matched and strain-balanced III-V semiconductor superlattices

The optical properties of bulk InAs{sub 0.936}Bi{sub 0.064} grown by molecular beam epitaxy on a (100)-oriented GaSb substrate are measured using spectroscopic ellipsometry. The index of refraction and absorption coefficient are measured over photon energies ranging from 44 meV to 4.4 eV and are used to identify the room temperature bandgap energy of bulk InAs{sub 0.936}Bi{sub 0.064} as 60.6 meV. The bandgap of InAsBi is expressed as a function of Bi mole fraction using the band anticrossing model and a characteristic coupling strength of 1.529 eV between the Bi impurity state and the InAs valence band. These results are programmed into a software tool that calculates the miniband structure of semiconductor superlattices and identifies optimal designs in terms of maximizing the electron-hole wavefunction overlap as a function of transition energy. These functionalities are demonstrated by mapping the design spaces of lattice-matched GaSb/InAs{sub 0.911}Sb{sub 0.089} and GaSb/InAs{sub 0.932}Bi{sub 0.068} and strain-balanced InAs/InAsSb, InAs/GaInSb, and InAs/InAsBi superlattices on GaSb. The absorption properties of each of these material systems are directly compared by relating the wavefunction overlap square to the absorption coefficient of each optimized design. Optimal design criteria are provided for key detector wavelengths for each superlattice system. The optimal design mid-wave infrared InAs/InAsSb superlattice is grown using molecular beam epitaxy, and its optical properties are evaluated using spectroscopic ellipsometry and photoluminescence spectroscopy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A review of Sb 2 Se 3 photovoltaic absorber materials and thin-film solar cells

Energy generated from environmentally friendly, cost-effective solar cells is a key aspect for developing a clean renewable-energy economy. Non-toxic and Earth-abundant materials with high absorption coefficient (>10 5 cm -1 ) and optimal bandgap (1-1.5 eV) have received great attention as photovoltaic (PV) absorber layers during the last few decades. Among them, antimony selenide (Sb 2 Se 3 ) has been a promising PV absorber, with steadily increasing power-conversion efficiency (PCE) compared to other emerging compounds. Very recent studies showed that high-quality ZnO:Al/ZnO/CdS/TiO 2 /Sb 2 Se 3 /MoSe 2 /Mo devices with PCE of 9.2% can be fabricated using cost-effective novel compounds. Considering these recent advances, this article provides an overview of the material properties of Sb2Se3 thin films and the recent progress made with Sb 2 Se 3 -based solar cells. Furthermore, analysis of Sb 2 Se 3 -based thin-film solar cells has also shown that the devices have relatively good light management due to their suitable bandgap and high absorption coefficient, whereas carrier management, i.e. collection efficiency of photo-generated carriers, needs significant improvement. Overall, this study provides background knowledge on material properties and device performance and suggests main research directions to overcome the limiting factors of solar cell performance.

14 SOLAR ENERGY↗

Assessing the link between aerosol mixing state, structure and composition and their optical properties: Ascension Island as a testbed for the South‐East Atlantic aerosol regimes

Forest and savanna fires are a major source of pollution over the globe. Such fire events emit to the atmosphere a considerable amount of “fluffy” fractal black looking particles that are often referred to as black carbon (BC) or soot aerosols. In fact, BC particles (aerosols) emitted from savanna and agricultural fires over the African continent play an important role in the region’s and the global climate. These fires occur each year between July and October, which is referred to as the biomass burning (BB) season and are considered among the globe's largest man-made emission sources of BC particles. However, during these fire events, not only BC particles are emitted, but also other types of particles and gases that can interact with each other to create new particles, generating a slew of particles often generally referred to as BB aerosols. Although the majority of the fire emissions occur inland in the sub-Saharan part of Africa, their effect reaches far beyond the continent due to the prevailing easterly winds, which transport those aerosols over the South-East Atlantic (SEA) ocean, off the west-coast of Africa. The reason why these particles are so important to the regional and global climate is that they absorb sunlight radiation, which overall warms the climate. However, the magnitude of this warming effect is highly uncertain and depends upon a multitude of aspects. Our overarching goal for this project was to better understand the changes in the aerosol properties as they transport from fire sources downstream toward the ocean and how this can eventually affect the earth's radiative budget in terms of warming or cooling. Following the above, our work here was focused on the investigation of the African BB aerosol plumes mixing state (mixing of BB aerosols and other aerosol types), composition and size distribution as they transport from the African continent towards the SEA ocean, and their link with some of the commonly measurable bulk optical properties such as mass absorption coefficient (MAC) and single scattering albedo (SSA). We utilized three field missions that were conducted over the SEA ocean between 2016 and 2018. Specifically, we used (1) ground-based measurements from the DOE ARM Mobile Facility (AMF1), which was deployed at Ascension Island (ASI) for the LASIC (Layered Atlantic Smoke Interactions with Clouds) campaign between June 2016 and October 2017, (2) airborne measurements from the UK CLARIFY (Clouds and Aerosol Radiative impacts and Forcing) campaign during Aug-Sep-2017, and (3) airborne measurements from the ORACLES (Observations of Aerosols above Clouds and their interactions) campaign during Aug-2017, and Sep-Oct-2018. The three campaigns cover a relatively large region, from the western African coast on the east towards Ascension Island in the middle of the SEA to the west. We used the data gathered by these campaigns to find how BB properties and composition change from near emission sources (the ORACLES campaign flights) downstream (the CLARIFY flights and the ground based LASIC measurements). We used particle trajectory following methodologies to connect the measurements from the different campaigns, which allowed us to follow a certain aerosol plume (airmass) from near-source towards Ascension Island. We found out that atmospheric aging processes governed by the UV light from the sun (photochemistry) and cloud processes (aqueous chemistry) govern the changes seen in the particle composition during the transport were more dominant in dictating aerosol composition than specific emission composition or source types. We assessed how aerosol optical properties change during the BB season and what are the main drivers of this change. We found that the enhanced ratio of BC to CO is well correlated with single scattering albedo (SSA) and mass absorption coefficient (MACBC), providing a simple way to estimate the aerosol optical characteristics in the south-eastern Atlantic Ocean. From the analysis of the location of BB, the primary source fuel, the water content in the fuel, combined with the mean cloud cover and precipitation in the transport areas of the BB plume, we conclude that the increase in BC/CO from June to August is likely to be caused by burning becoming more flaming (hot fires), and the decrease in BC/CO in September and October may be caused by smoldering (colder) fires. We found that aerosol hygroscopicity increases with decreasing altitude below 2km, and that enhanced BB hygroscopicity at lower altitudes is mainly due to a lower organic aerosol (OA) fraction, increased sulfate fraction, and greater hygroscopicity parameter of OA at lower altitudes.

54 ENVIRONMENTAL SCIENCES↗