Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VIBRATION TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Vibration Testing of Electrical Cables to Quantify Loads at Tie-Down Locations

The standard method for defining static equivalent structural load factors for components is based on Mile s equation. Unless test data is available, 5% critical damping is assumed for all components when calculating loads. Application of this method to electrical cable tie-down hardware often results in high loads, which often exceed the capability of typical tie-down options such as cable ties and P-clamps. Random vibration testing of electrical cables was used to better understand the factors that influence component loads: natural frequency, damping, and mass participation. An initial round of vibration testing successfully identified variables of interest, checked out the test fixture and instrumentation, and provided justification for removing some conservatism in the standard method. Additional testing is planned that will include a larger range of cable sizes for the most significant contributors to load as variables to further refine loads at cable tie-down points. Completed testing has provided justification to reduce loads at cable tie-downs by 45% with additional refinement based on measured cable natural frequencies.

Dutson, Joseph D.↗
NASA NTRS2000

Force limit specifications vs. design limit loads in vibration testing

The purpose of the work presented herein is to discuss the results of force limit notching during vibration testing with respect to the traditional limit load design criteria. By using a single-degree-of-freedom (SDOF) system approach, this work shows that with an appropriate force specification the notched response due to force limiting will result in loads comparable with the structural design limit criteria.

force limiting vibration testing flight limit load↗
NASA NTRS2020

Multiple Shaker Placement for Ground Vibration Test of X-59 Aircraft Using Topology Optimization

A multiple shaker placement methodology is developed and tested using a topology optimization technique. Current multiple shaker placement methodology requires optimum accelerometer placement and optimum single-shaker placement techniques. The proposed methodology is tested using a finite element model of the X-59 Low Boom Flight Demonstrator aircraft. The effective independence and the driving point acceleration transfer function (DPATF) methods are used for the accelerometer placement study. In this study, four shakers are used to excite each mode more effectively during the ground vibration test; all the modes of interest thus are separated into four groups. Each shaker takes care of a separate group of modes. Grouping the modes of interest is performed utilizing topology optimization. The number of modes for each group therefore will be automatically decided during grouping. For each group of modes, perform the following two steps to determine optimal location of four shakers: 1) At each accelerometer location, compare the magnitude of DPATF values at natural frequencies, select the minimum value, and make a vector with these minimum values of the DPATF magnitudes for each group; and 2) Select the degrees of freedom corresponding to the maximum value of this vector. The objective function value is the maximum value of the vector with minimum value of the magnitude of the superposed acceleration transfer function. This objective function value is maximized by changing the modes for each group. Forty accelerometers are enough to have good correlation between mode shapes obtained from the reduced order model and the simulated ground vibration test.

Optimization Analysis↗
NASA NTRSDate not supplied

Are We Shaking Too Much? An Inquiry into Environmental Random Vibration Testing Margins

Problem Statement: The conventional, MIL-STD-810 approach to vibration environment derivation is perhaps too conservative, leading to unnecessary failures during acceptance & qualification vibration testing of Armstrong’s one-off flight equipment. Objective: This presentation explores some alternative understandings of the distributions of vibration severity in nonstationary environments. Proposed methods of sorting and adding appropriate margin are explored.

Scott L. Stebbins↗
NASA NTRSDate not supplied

All-Electric X-Plane, X-57 Mod II Ground Vibration Test

As part of the National Aeronautics and Space Administration New Aviation Horizons initiative to demonstrate and validate future high-impact concepts and technologies, the X-57 Maxwell airplane--the first all-electric X-plane--was conceived to advance research in the area of electric propulsion to show the feasibility of minimizing fuel use, reducing emissions, and lowering noise during flight. Through several configuration modifications to the X-57 airplane, validation of electrical-powered flight with increasing efficiency between each modification when compared to the baseline original airplane is anticipated. In the case of the X-57 Modification II airplane, a ground vibration test was needed to identify the airplane structural modes and use them to update and validate the finite element model. To determine the airworthiness of the airplane the updated finite element model will be utilized to investigate both classical and whirl flutter. The X-57ModificationII ground vibration test was performed by the National Aeronautics and Space Administration Armstrong Flight Research Center Flight Loads Laboratory. This paper will highlight the testing performed to acquire the modal data as well as the results.

Natalie Dawn Spivey↗
NASA NTRS1984

Ground vibration test of F-16 airplane with initial decoupler pylon

A ground vibration test was conducted on an F-16 airplane loaded on each wing with a 370-gal tank mounted on a standard pylon, a GBU-8 store mounted on a decoupler pylon, and an AIM-9J missile mounted on a wing-tip launcher. The decoupler pylon is a passive wing/store flutter-suppression device. The test was conducted prior to initial flight tests to determine the modal frequencies, mode shapes, and structural damping coefficients. The data presented include frequency response plots, force effect plots, and limited mode shape data.

Cazier, F. W., Jr.↗
NASA NTRS1998

A Magnetic Suspension and Excitation System for Spin Vibration Testing of Turbomachinery Blades

The Dynamic Spin Rig (DSR) is used to perform vibration tests of turbomachinery blades and components under spinning conditions in a vacuum. A heteropolar radial active magnetic bearing was integrated into the DSR to provide non-contact magnetic suspension and mechanical excitation of the rotor to induce turbomachinery blade vibrations. The magnetic bearing replaces one of the two existing conventional radial ball bearings. Prior operation of the DSR used two voice-coil type linear electromagnetic shakers which provided axial excitation of the rotor. The new magnetic suspension and excitation system has provided enhanced testing capabilities. Tests were performed at high rotational speeds for longer duration and higher vibration amplitudes. Some characteristics of the system include magnetic bearing stiffness values up to 60,000 lb./in., closed loop control bandwidth around 500 Hz, and multi-directional radial excitation of the rotor. This paper reports on the implementation and operation of this system and presents some test results using this system.

Johnson, Dexter↗
NASA NTRS2002

Structural loads prediction in force-limited vibration testing

The purpose of this paper is to study whether the force limiting has accomplished the notching requirement to limit the equipment structural response in low frequency vibration tests to something less than the design load.

force limiting vibration testing flight limit load↗
NASA NTRS1974

Workmanship vibration test of the SAS-B spacecraft

The occurrence of a technical problem made it necessary to remove the transmitter from the SAS-B spacecraft. The transmitter was repaired and reinstalled in the spacecraft. After this operation it was necessary to test the mechanical properties of the reassembled spacecraft in a vibration test to be conducted near the spacecraft launching place on the San Marco Range in the Indian Ocean. A vibration system was, therefore, sent to San Marco. The design of the vibration system is discussed, giving attention also to alternative solutions for conducting the required tests.

Demas, L. J.↗
NASA NTRS1972

Shock and vibration tests of uranium mononitride fuel pellets for a space power nuclear reactor

Shock and vibration tests were conducted on cylindrically shaped, depleted, uranium mononitride (UN) fuel pellets. The structural capabilities of the pellets were determined under exposure to shock and vibration loading which a nuclear reactor may encounter during launching into space. Various combinations of diametral and axial clearances between the pellets and their enclosing structures were tested. The results of these tests indicate that for present fabrication of UN pellets, a diametral clearance of 0.254 millimeter and an axial clearance of 0.025 millimeter are tolerable when subjected to launch-induced loads.

Adams, D. W.↗
NASA NTRS1994

Vibration Test Force Limits Derived From Frequency Shift Method

The two-degree-of-freedom system (TDFS) method used to derive force specifications for force limited vibration tests at JPL is reviewed and some of the limitations of the method and of the simple TDFS model are discussed. A new improved frequency shift force prediction method is developed and applied to a more complex model where the load and source have both residual and modal masses.

force↗
NASA NTRS2001

Vibration Test Demonstrated Dynamic Capability of an Operating Stirling Convertor

The NASA Glenn Research Center and the U.S. Department of Energy are currently developing a high-efficiency, long-life, free piston Stirling convertor for use as an advanced spacecraft power system for future NASA missions. As part of this development, a Stirling Technology Demonstrator Converter (TDC), developed by Stirling Technology Company for the Department of Energy, was vibration tested at Glenn's Structural Dynamics Laboratory in November and December 1999. This testing demonstrated that the Stirling TDC is able to withstand the harsh random vibration (20 to 2000 Hz) seen during a typical spacecraft launch and to survive with no structural damage or functional power performance degradation, thereby enabling its use in future spacecraft power systems. Glenn and Stirling personnel conducted tests on a single 55 We TDC. The purpose was to characterize the TDC's structural response to vibration and to determine if the TDC could survive the vibration criteria established by the Jet Propulsion Laboratory for launch environments. The TDC was operated at full-stroke and full power conditions during the vibration testing.

Hughes, William O.↗
NASA NTRS1987

Small-scale rotor test rig capabilities for testing vibration alleviation algorithms

A test was conducted to assess the capabilities of a small scale rotor test rig for implementing higher harmonic control and stability augmentation algorithms. The test rig uses three high speed actuators to excite the swashplate over a range of frequencies. The actuator position signals were monitored to measure the response amplitudes at several frequencies. The ratio of response amplitude to excitation amplitude was plotted as a function of frequency. In addition to actuator performance, acceleration from six accelerometers placed on the test rig was monitored to determine whether a linear relationship exists between the harmonics of N/Rev control input and the least square error (LSE) identification technique was used to identify local and global transfer matrices for two rotor speeds at two batch sizes each. It was determined that the multicyclic control computer system interfaced very well with the rotor system and kept track of the input accelerometer signals and their phase angles. However, the current high speed actuators were found to be incapable of providing sufficient control authority at the higher excitation frequencies.

Jacklin, Stephen A.↗
NASA NTRS1982

The development and verification of shuttle orbiter random vibration test requirements

The unique space shuttle vehicle size, weight, and configuration gave rise to problems in determining vibration requirements and in verifying structural integrity for anticipated mission environments. The applications of large-scale vibration testing played a prominent part in qualifying the shuttle for its intended missions. Severe vibration excitation from rocket engines, aerodynamic noise, and onboard equipment are expected on each shuttle flight. Scale-model wind tunnel and rocket firing tests, as well as full-size rocket engine tests were relied on to define the random forcing functions. The determination of structural response to these environments is described as well as evaluations of measured flight data and comparison with predicted design and test criteria.

Coody, M. C.↗
NASA NTRS1990

Three-dimensional random vibration testing definition and simulation

An approach is presented for the definition of 3D random vibration test requirements for multiaxial shaker systems. In particular, it is shown that, by utilizing coherence functions for cross-correlation effects, test requirements can be defined in a simple way and provide a more realistic environmental simulation. The method is applicable to the simulation of all field environments and can be similarly employed to develop laboratory test requirements based on field data. Example problems are presented to demonstrate the approach.

Chang, Kurng Y.↗