Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Two-dimensional material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Two-dimensional Finite Element Modeling for Modeling Tectonic Stress and Strain

Techniques of finite element analysis in two dimensional plane strain were applied to problems of geophysics and tectonics. More specifically, the flexibility of the finite element method was employed to address problems involving geological complexity and fault interactions. The modeling of effective anisotropy in material elastic properties proved useful in describing the deformation of faulted crustal blocks. The applications of this modeling work to problems of actual tectonics in southern California was explored. Preliminary models show encouraging agreement with measured tectonic strain in this region, and modeling work was done to gain an understanding of the stress state in a locked fault region with future seismic potential.

Lyzenga, G. A.↗
NASA NTRS1983

Thermal stresses in bonded solar cells - The effect of the adhesive layer

A two-dimensional, rectangular model of a proposed solar cell structure is analyzed as two plate elements bonded with an elastic continuum. The governing equations are formulated using the principle of minimum potential energy, with displacement components that vary linearly through the thickness of the adhesive layer. An approximate solution is constructed for a particular class of material properties and is characterized by a boundary layer near the unloaded edge. Both interface stress components achieve their largest values at the edge, and the maximum shear stress is independent of the Young's Modulus of the substrate.

Williams, H. E.↗
NASA NTRS1985

Onset of solar flares as predicted by two-dimensional MHD-models of quiescent prominences

The close connection between the sudden disapperance (disparition brusque) of the quiescent prominences and the two-ribbon flares are well known. During this dynamic phase the prominence ascends rapidly (typically with a velocity about 100 Km/sec) and disappears. In another later stage is observed material falling back into the chromosphere. The impact of this downfalling matter on the chromosphere produces the H brightening, which shows the symmetric double pattern. The occurence of the disparition brusque is thought to be a consequence of a plasma instability of magnetohydrostatic (MHD) structures. By means of the MHD-energy principle, the stability properties of four prominence models are analyzed. It is shown that all considered models undergo instabilities for parameters outside of the observed range at quiescent prominences. The possibility that such instabilities in the flare parameter range may indicate just the onset of a flare is considered.

Galindotrejo, J.↗
NASA NTRS1986

Hyperspectral Infrared Images of Terrain

Images at 128 wavelengths allow direct identification of many earth surface materials. Two reports describe advanced airborne spectrometer that creates images of terrain at many wavelengths. Airborne imaging spectrometer (AIS) produces two-dimensional images in 128 spectral bands in 1.2-to-2.4-micrometer wavelength region. Images created by 32-by-32 array of mercury cadmium telluride detector elements. Array views swath of Earth below moving aircraft. Used for agricultural, geological, and other surveys.

Vane, G.↗
NASA NTRS1985

Engineering and programming manual: Two-dimensional kinetic reference computer program (TDK)

The Two Dimensional Kinetics (TDK) computer program is a primary tool in applying the JANNAF liquid rocket thrust chamber performance prediction methodology. The development of a methodology that includes all aspects of rocket engine performance from analytical calculation to test measurements, that is physically accurate and consistent, and that serves as an industry and government reference is presented. Recent interest in rocket engines that operate at high expansion ratio, such as most Orbit Transfer Vehicle (OTV) engine designs, has required an extension of the analytical methods used by the TDK computer program. Thus, the version of TDK that is described in this manual is in many respects different from the 1973 version of the program. This new material reflects the new capabilities of the TDK computer program, the most important of which are described.

Nickerson, G. R.↗
NASA NTRS1987

Strain-energy-release rate analysis of the end-notched flexure specimen using the finite-element method

Two-dimensional finite-element analysis of the end-notched flexure specimen was performed using 8-node isoparametric, parabolic elements to evaluate compliance and mode II strain energy release rates, G sub II. The G sub II values were computed using two different techniques: the virtural crack-closure technique (VCCT) and the rate of change of compliance with crack length (compliance derivative method). The analysis was performed for various crack-length-to-semi-span (a/L) ratios ranging from 0.2 to 0.9. Three material systems representing a wide range of material properties were analyzed. The compliance and strain energy release rates of the specimen calculated with the present finite-element analysis agree very well with beam theory equations including transverse shear. The G sub II values calculated using the compliance derivative method compared extremely well with those calculated using the VCCT. The G sub II values obtained by the compliance derivative method using the top or bottom beam deflections agreed closely with each other. The strain energy release rates from a plane-stress analysis were higher than the plane-strain values by only a small percentage, indicating that either assumption may be used in the analysis. The G sub II values for one material system calculated from the finite-element analysis agreed with one solution in the literature and disagreed with the other solution in the literature.

Salpekar, S. A.↗
NASA NTRS1989

Predicting The Propagation Of Cracks

Advanced Crack Propagation Predictive Analysis Program, FLAGR04, developed as aid in predicting growth of preexisting flaws and cracks in structural components. Provides fracture-mechanics analyst with computerized method of evaluation of "safe crack-growth life" capabilities of structural components. Also used to evaluate tolerance-to-damage aspects of given structural design. Predicts growth of crack by use of two-dimensional model independently predicting growth of flaw in two directions based on calculation of stress-intensity factors. Input to FLAGR04 consists of initial definition of crack, type of rate solution, type and geometry of flaw, properties of material, data on load spectrum, load-stress functions, and design-limit stress levels. Output includes echo of input with any error or warning message and history of propagation of crack. Written in FORTRAN IV.

Tianlai, HU↗
NASA NTRS1989

Implementation of equivalent domain integral method in the two-dimensional analysis of mixed mode problems

An equivalent domain integral (EDI) method for calculating J-intergrals for two-dimensional cracked elastic bodies is presented. The details of the method and its implementation are presented for isoparametric elements. The total and product integrals consist of the sum of an area of domain integral and line integrals on the crack faces. The line integrals vanish only when the crack faces are traction free and the loading is either pure mode 1 or pure mode 2 or a combination of both with only the square-root singular term in the stress field. The EDI method gave accurate values of the J-integrals for two mode I and two mixed mode problems. Numerical studies showed that domains consisting of one layer of elements are sufficient to obtain accurate J-integral values. Two procedures for separating the individual modes from the domain integrals are presented. The procedure that uses the symmetric and antisymmetric components of the stress and displacement fields to calculate the individual modes gave accurate values of the integrals for all problems analyzed. The EDI method when applied to a problem of an interface crack in two different materials showed that the mode 1 and mode 2 components are domain dependent while the total integral is not. This behavior is caused by the presence of the oscillatory part of the singularity in bimaterial crack problems. The EDI method, thus, shows behavior similar to the virtual crack closure method for bimaterial problems.

Raju, I. S.↗
NASA NTRS1988

Space Shuttle Main Engine High Pressure Fuel Turbopump Turbine Blade Cracking

The analytical results from two-dimensional (2D) and three-dimensional (3D) finite element model investigations into the cracking of Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) first- and second-stage turbine blades are presented. Specifically, the initiation causes for transverse cracks on the pressure side of the firststage blade fir tree lobes and face/corner cracks on the downstream fir tree face of the second-state blade are evaluated. Because the blade material, MAR-M-246 Hf (DS), is highly susceptible to hydrogen embrittlement in the -100 F to 400 F thermal environment, a steady-state condition (full power level = 109 percent) rather than a start-up or shut-down transient was considered to be the most likely candidate for generating a high-strain state in the fir tree areas. Results of the analyses yielded strain levels on both first- and second-stage blade fir tree regions that are of a magnitude to cause hydrogen assisted low cycle fatigue cracking. Also evident from the analysis is that a positive margin against fir tree cracking exists for the planned design modifications, which include shot peening for both first- and second-stage blade fir tree areas.

Lee, Henry↗
NASA NTRS1988

Infrared systems and components II; Proceedings of the Meeting, Los Angeles, CA, Jan. 14, 15, 1988

The present conference on the development status of IR electrooptics technologies discusses topics concerning such systems' materials and architectures, their modeling and data processing requirements, and advancements in IR automatic target recognition. Attention is given to active multispectral three-dimensional vision sensor image evaluation, a VHSIC processor-based real-time image tracker, the use of Al-alloy castings as diamond machining substrates for optical surfaces, a two-dimensional recognition range model, calculations of the optical blurring in IR systems, synthetic IR scene generation, and automatic target recognition evaluation.

Liaw, H. M.↗
NASA NTRS1988

Strain energy release rate analysis of the end-notched flexure specimen using the finite-element method

Two-dimensional finite-element analysis of the end-notched flexure specimen was performed using 8-node isoparametric, parabolic elements to evaluate compliance and mode II strain energy release rates, G sub II. The G sub II values were computed using two different techniques: the virtual crack-closure technique (VCCT) and the rate of change of compliance with crack length (compliance derivative method). The analysis was performed for various crack-length-to-semi-span (a/L) ratios ranging from 0.2 to 0.9. Three material systems representing a wide range of material properties were analyzed. The compliance and strain energy release rates of the specimen calculated with the present finite-element analysis agree very well with beam theory equations including transverse shear. The G sub II values calculated using the compliance derivative method compared extremely well with those calculated using the VCCT. The G sub II values obtained by the compliance derivative method using the top or bottom beam deflections agreed closely with each other. The strain energy release rates from a plane-stress analysis were higher than the plane-strain values by only a small percentage, indicating that either assumption may be used in the analysis. The G sub II values for one material system calculated from the finte-element analysis agreed with one solution in the literature and disagreed with the other solution in the literature.

Salpekar, S. A.↗
NASA NTRS1989

Extension-torsion coupling behavior of advanced composite tilt-rotor blades

An analytic model was developed to study the extension-bend-twist coupling behavior of an advanced composite helicopter or tilt-rotor blade. The outer surface of the blade is defined by rotating an arbitrary cross section about an initial twist axis. The cross section can be nonhomogeneous and composed of generally anisotropic materials. The model is developed based upon a three dimensional elasticity approach that is recast as a coupled two-dimensional boundary value problem defined in a curvilinear coordinate system. Displacement solutions are written in terms of known functions that represent extension, bending, and twisting and unknown functions for local cross section deformations. The unknown local deformation functions are determined by applying the principle of minimum potential energy to the discretized two-dimensional cross section. This is an application of the Ritz method, where the trial function family is the displacement field associated with a finite element (8-node isoparametric quadrilaterals) representation of the section. A computer program was written where the cross section is discretized into 8-node quadrilateral subregions. Initially the program was verified using previously published results (both three-dimensional elasticity and technical beam theory) for pretwisted isotropic bars with an elliptical cross section. In addition, solid and thin-wall multi-cell NACA-0012 airfoil sections were analyzed to illustrate the pronounced effects that pretwist, initial twist axis location, and spar location has on coupled behavior. Currently, a series of advanced composite airfoils are being modeled in order to assess how the use of laminated composite materials interacts with pretwist to alter the coupling behavior of the blade. These studies will investigate the use of different ply angle orientations and the use of symmetric versus unsymmetric laminates.

Kosmatka, J. B.↗
NASA NTRS1990

The structure and evolution of radiatively cooling jets

The two-dimensional simulations presently used to characterize the structure and evolution of radiatively cooling supersonic jets reveal that cooling jet morphologies resemble those of adiabatic outflows, but with the fundamental difference that a dense, cold shell will condense out of the shocked gas at the head of the jet when the cooling distance behind either of the two principal shocks is smaller than the jet radius. For very high cooling rates, the material that accumulates at the head of the jet forms an extended plug of cold gas resembling the 'nose cone' observed in numerical simulations of strongly magnetized adiabatic jets. An investigation is made of the dependence of jet properties on the density ratio between the beam and the ambient medium, as well as on the strength of radiative cooling.

Blondin, John M.↗
NASA NTRS1990

Users manual for AUTOMESH-2D: A program of automatic mesh generation for two-dimensional scattering analysis by the finite element method

AUTOMESH-2D is a computer program specifically designed as a preprocessor for the scattering analysis of two dimensional bodies by the finite element method. This program was developed due to a need for reproducing the effort required to define and check the geometry data, element topology, and material properties. There are six modules in the program: (1) Parameter Specification; (2) Data Input; (3) Node Generation; (4) Element Generation; (5) Mesh Smoothing; and (5) Data File Generation.

Hua, Chongyu↗
NASA NTRS1990

Edge delamination of composite laminates subject to combined tension and torsional loading

Delamination is a common failure mode of laminated composite materials. Edge delamination is important since it results in reduced stiffness and strength of the laminate. The tension/torsion load condition is of particular significance to the structural integrity of composite helicopter rotor systems. Material coupons can easily be tested under this type of loading in servo-hydraulic tension/torsion test stands using techniques very similar to those used for the Edge Delamination Tensile Test (EDT) delamination specimen. Edge delamination of specimens loaded in tension was successfully analyzed by several investigators using both classical laminate theory and quasi-three dimensional (Q3D) finite element techniques. The former analysis technique can be used to predict the total strain energy release rate, while the latter technique enables the calculation of the mixed-mode strain energy release rates. The Q3D analysis is very efficient since it produces a three-dimensional solution to a two-dimensional domain. A computer program was developed which generates PATRAN commands to generate the finite element model. PATRAN is a pre- and post-processor which is commonly used with a variety of finite element programs such as MCS/NASTRAN. The program creates a sufficiently dense mesh at the delamination crack tips to support a mixed-mode fracture mechanics analysis. The program creates a coarse mesh in those regions where the gradients in the stress field are low (away from the delamination regions). A transition mesh is defined between these regions. This program is capable of generating a mesh for an arbitrarily oriented matrix crack. This program significantly reduces the modeling time required to generate these finite element meshes, thus providing a realistic tool with which to investigate the tension torsion problem.

Hooper, Steven J.↗
NASA NTRS1990

MBE HgCdTe heterostructure detectors

HgCdTe has been the mainstay for medium (3 to 5 micron) and long (10 to 14 micron) wavelength infrared detectors in recent years. Conventional growth and processing techniques are continuing to improve the material. However, the additional ability to tailor composition and placement of doped layers on the tens of angstroms scale using molecular beam epitaxy (MBE) provides the opportunity for new device physics and concepts to be utilized. MBE-based device structures to be discussed here can be grouped into two categories: tailored conventional structures and quantum structures. The tailored conventional structures are improvements on familiar devices, but make use of the ability to create layers of varying composition, and thus band gap, at will. The heterostructure junction can be positioned independently of doping p-n junctions. This allows the small band gap region in which the absorption occurs to be separated from a larger band gap region in which the electric field is large and where unwanted tunneling can occur. Data from hybrid MBE/liquid phase epitaxy (LPE)/bulk structures are given. Quantum structures include the HgTe-CdTe superlattice, in which the band gap and transport can be controlled by alternating thin layers (tens of angstroms thick) of HgTe and CdTe. The superlattice has been shown to exhibit behavior which is non-alloy like, including very high hole mobilities, two-dimensional structure in the absorption coefficient, resonant tunneling, and anisotropic transport.

Schulman, Joel N.↗
NASA NTRS1991

Imaging of molecular hydrogen and oxygen by single and two-photon fluorescence using laser and flashlamp sources

Two flow visualization techniques, i.e., simultaneous two-dimensional fluorescence imaging of H2 and O2 in a diffusion flame, and quasi-linear fluorescence imaging of O2, are presented. The first uses an injection-locked argon-fluoride excimer laser and a partial overlap of a two-photon ground state absorption in H2 with a single photon absorption from a vibrational level in O2. The second uses a simple, high-intensity ultraviolet flashlamp which provides a flux of photons in the 180-195 nm range, sufficient to produce a quasi-one-dimensional fluorescence image of hot/room temperature oxygen. Both techniques do not require that a seed material be introduced into the flow, they can image major flow constituents, and provide an instantaneous snapshot of the flow.

Diskin, Glenn S.↗
NASA NTRS1956

Theoretical investigation of flutter of two-dimensional flat panels with one surface exposed to supersonic potential flow

A Rayleigh type analysis involving chosen modes of the panel as degrees of freedom is used to treat the flutter of a two-dimensional flat panel supported at its leading and trailing edges and subjected to a middle-plane tensile force. The panel has a supersonic stream passing over its upper surface and still air below. The aerodynamic forces due to the supersonic stream are obtained from the theory for linearized two-dimensional unsteady flow and the forces due to the still air are obtained from acoustical theory. In order to study the effect of increasing the number of modes in the analysis, two and then four modes are employed. The modes used are the first four natural modes of the panel in a vacuum with no tensile force acting. The analysis includes these variables: Mach number, structural damping, tensile force, density of the still air, and edge fixity (clamped and pinned). For certain combinations of these variables, stability boundaries are obtained which can be used to determine the panel thickness required to prevent flutter for any panel material and altitude.

Nelson, Herbert C↗