Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TATB”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Direct observation of diamond formation in a shock-compressed high explosive

Understanding the formation timescale and structure of carbonaceous reaction products is critical for modeling the high-pressure equation-of-state of organic materials. We use the National Ignition Facility to shock-compress polycrystalline TATB (C 6 H 6 N 6 O 6 ) samples to ~70–130 GPa and ~4000–5500 K, employing in situ nanosecond X-ray diffraction to probe reaction products and velocimetry to measure transmitted compression wave profiles. Our diffraction data is consistent with the formation of diamond over timescales less than ~60 ns. This represents carbon condensation from a molecular explosive on timescales three times faster than previously reported and the earliest observation of diamond produced from reacting TATB. Reactive flow simulations with explicit chemistry reproduce the observed temporal structure within wave profiles to inform the distribution of P-T states. These findings provide direct evidence of ultrafast diamond formation in a reactive system at extreme conditions and provide new constraints for models of shock and detonation chemistry.

Clarke, Samantha M. [Lawrence Livermore National L↗

Temperature of shocked plastic bonded explosive PBX 9502 measured with spontaneous Stokes/anti-Stokes Raman

Raman spectra and velocimetry of shocked PBX 9502 (plastic bonded explosive composed of 95% triaminotrinitrobenzene (TATB) and 5% 3M Company Kel F-800 polymer binder) are reported with the Stokes/anti-Stokes ratio used to determine temperature after the shock reflects from a lithium fluoride window. Final pressures up to 14.5 GPa were tested, but the pressure induced absorption of TATB caused the Raman signal to decrease exponentially with pressure. The reflected shock temperature could be determined to 7 GPa, with an average increase of 14.9 K/GPa. Suggestions to adapt the technique to permit thermometry at higher temperatures are discussed, as are comparisons to a recently proposed equation of state for PBX 9502.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Shock temperature dependent rate law for plastic bonded explosives

A reactive flow model for the tri-amino-tri-nitro-benzene (TATB) based plastic bonded explosive PBX 9502 (95% TATB, 5% polymeric binder Kel-F 800) is presented. This newly devised model is based primarily on the shock temperature of the material, along with local pressure, and accurately models a broader range of detonation and initiation scenarios. Specifically, sensitivity changes to the initial explosive temperature are accounted for naturally and with a single set of parameters. The equation of state forms for the reactants and products, as well as the thermodynamic closure of pressure and temperature equilibration, are carried over from the Wescott-Stewart-Davis (WSD) model [Wescott et al., J. Appl. Phys. 98, 053514 (2005) and “Modeling detonation diffraction and dead zones in PBX-9502,” in Proceedings of the Thirteenth International Detonation Symposium (2006)]. This newly devised model, with Arrhenius state dependence on the shock temperature, based on the WSD equation of states, is denoted by AWSD. In conclusion, modifying an existing implementation of the WSD model to the AWSD model in a hydrocode is a rather straightforward procedure.

36 MATERIALS SCIENCE↗

Comparing the shock sensitivity of insensitive energetic materials

We present a tabletop method to study the shock sensitivity of plastic-bonded explosives that are considered shock insensitive using high dynamic range optical emission spectroscopy with laser-launched km/s flyer plate impacts (2, 3, and 4 km/s), which measures the spectral radiance (the emission spectrum vs a calibrated intensity standard) every 0.8 ns in the nanosecond and microsecond regimes. The explosives were TATB (1,3,5 trinitro, 2,4,6 triamino benzene), FOX-7 (1,1-diamino-2,2-dinitroethylene), LLM-105 (2,6-diamino-3,5-dinitropyrazine-1-oxide), and NTO (nitrotriazolone), all with 20% Sylgard 182 binder. Time resolving emission from shocked explosives produces a unique fingerprint at each shock pressure, and the emission temporal profile can be used to understand each material's shock response and the underlying mechanisms within the framework of the well-known shock ignition and growth models. Ignition was characterized by the emission intensity during nanosecond hot spot ignition. The growth process, which occurs after the shock has unloaded, was characterized by the time derivative of microsecond emission intensity. Singular-value decomposition was used to determine a characteristic spectral radiance over the entire time range, and this radiance was fit to a graybody model to determine a characteristic temperature Tc. Even though these insensitive explosives have similar shock sensitivities, our method can clearly distinguish their shock response. FOX-7 and NTO were the most sensitive, with FOX-7 having the greatest shock ignition sensitivity, growth rate, and Tc. LLM-105 was much less sensitive than FOX-7 and NTO, and TATB consistently showed the lowest sensitivity by any measure.

Akhtar, Meysam (ORCID:0000000243897837)↗

FY2014 LX-21 Blasting Cap Testing

For a new material to qualify as an Extremely Insensitive Substance (EIS), the material must pass the UN Test 7, EIS Cap Test. This test attempts to measure the shock sensitivity of the material to a standard detonator at its nominal shipping density. The standard detonator specified for this test is based upon the historical number eight, #8, blasting cap. The standard detonator must contain a base charge (output charge) greater than or equal to 450mg and have a detonation velocity of at least 7.0 km/s. The Du Pont E-1A blasting cap, which is no longer made by Du Pont, was originally used to qualify TATB-based insensitive materials in the DOE. This detonator met the requirements of the EIS Cap Test. Several other commercial vendors currently sell products that are listed as equivalent to a number eight blasting cap, but have, in several cases, exceeded the original output energy of the historical number eight. By the loose specification that the number eight contain at least 450mg of output explosive, any product containing at least this quantity can be labeled as a number eight. Indeed, for most applications, higher output energy merely means a better, more reliable product. For standards testing, variation the output energy greatly affects the test results. Pantex has maintained a quantity of the original, number eight blasting caps the DOE used to qualify TATB materials (The DOE uses an IHE qualification, which is similar to the HD 1.6 classification, and requires a similar EIS Cap Test.) In FY-13, we acquired blasting caps from the original Pantex supply and from two commercial vendors for characterization and comparison. Our goals were to first characterize each of the three standard detonators with the intention of using a detonator that was as equivalent to the Du Pont number eight blasting cap as possible. Second, to work with a commercial vendor to produce a number eight equivalent that would either be based on a safer initiation technology such as an exploding bridge wire (EBW) or exploding foil initiator (EFI) – most commercial units hot-wire based, which present considerable safety concerns.

42 ENGINEERING↗

Updating Critical Temperature Calculations for Several Secondary High Explosives

In designing experiments where high explosives (HEs) are heated, it is important to have an understanding of where thermal runaway may occur. This determination is often done by using the Frank-Kamenetskii (FK) equation. For several highly-studied HEs, the parameters necessary for FK calculations are typically referenced from decades-old literature, and more recent experimental data have shown that these values require adjustment. For example, some of the legacy parameters dangerously overpredict the critical temperature by tens of degrees relative to more recent observed values. Herein, we first summarize historical results and highlight the importance of insulation effects when estimating critical temperatures for small samples, which is especially relevant to small-scale aging, compatibility, and characterization experiments. Here, we then present updated FK parameters for several common secondary CHNO HEs like RDX, HMX, PETN, and TATB, as well as the first reported values for 2,6-Diamino-3,5-dinitropyrazine-1-oxide (LLM-105). Our updated parameters produce critical-temperature curves that are consistent with both mm-scale differentical scanning calorimetry (DSC) measurements and cm-scale data from the Lawrence Livermore National Laboratory one-dimensional time-to-explosion (ODTX) experiment. In analyzing the critical temperature versus sample size curves derived from the transcendental FK equation, we discovered that these curves are remarkably well described by a simple power-law function with a universal power of 0.142 and a HE-specific scaling factor.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Model for ratchet growth in PBX 9502

Polycrystalline solids composed of crystals with anisotropic thermal expansion coefficients exhibit ratchet growth (RG), a phenomenon characterized by a cumulative and irreversible volume expansion that develops upon exposing the material to cyclic excursions in temperature. We developed a statistical model for RG. The model attributes RG to the formation of intergranular cracks caused by tessellated internal stresses that develop during the thermal excursions. It is postulated that different sets of internal cracks form upon heating and cooling the polycrystalline solid. The model reproduces RG measurements in pressed TATB and PBX 9502 energetic materials and suggests an explanation for why the amplitude of RG generated by a heating excursion is larger than that generated by a subsequent cooling excursion of the same amplitude.

36 MATERIALS SCIENCE↗

Fracture toughness and crack propagation in LX-17 and PBX 9502 insensitive high explosives

High explosive materials, and in particular insensitive high explosive (IHE) materials, are of significant interest. TATB-based LX-17 and PBX 9502 are two IHE’s and mechanical properties are an important metric of performance. In this work we present, for the first time, a study of fracture as a function of temperature and displacement rate and starter crack length on billet pressed IHE materials using a standard three point bend technique. We demonstrated that the technique can yield consistent results over time by measuring samples from the same lots 4 years later and observed that the fracture toughness of LX-17 and PBX 9502 are similar. We also determined the temperature dependence for different starter crack lengths and found that the fracture toughness generally decreases with larger starter crack sizes and temperatures. For the LX-17, where a wide temperature range of -60 C to 50 C was investigated, the impact of temperature on fracture toughness between -20 C and 23 C was less than expected. For the PBX 9502 we observed the difference in fracture toughness values between -20 C and 23 C did depend on the particular lot, and also there was a tendency of the fracture toughness to scale with the tensile strength. We also investigated the effect of a lower displacement rate and observed that while the impact on the fracture toughness was relatively small, the samples surprisingly did not break (fail) after exceeding the peak load. We took advantage of this to perform x-ray computed tomography (CT) of the samples to image crack propagation in the intact samples. We observed that cracks were generally straight and unaffected by the microstructure in the LX-17, in contrast to the PBX 9502 where the direction of the cracks would frequently change and were likely influenced by the underlying microstructure.

36 MATERIALS SCIENCE↗

New self-consistent homogenization for thermo-elastic polycrystals with imperfect interfaces

Here we present a new thermo-elastic self-consistent formulation to calculate the thermo-mechanical response of polycrystalline aggregates with imperfect interfaces. The new model is based on an improved treatment of the effect of imperfect interfaces on the micromechanical response of the grains compared to pre-existing models. New expressions/algorithms are derived for the effective elastic and thermal properties, localization relations, and calculation of intragranular field fluctuations. In addition, derivation of a novel integral equation for the strain field in a heterogeneous elastic medium subjected to arbitrary thermal strain field and displacement jumps is presented. The new model is applied to study the effective thermo-elastic properties and average field fluctuations as a function of the interface properties for imperfectly-bonded triaminotrinitrobenzene (TATB) polycrystalline granular aggregates. The proposed formulation is general in the sense that it can be extended to other material systems and deformation regimes that require a proper consideration of the effect of imperfect interface properties on the material's thermo-mechanical response.

36 MATERIALS SCIENCE↗

Spatial Heterodyne Raman Spectrometer (SHRS) for In Situ Chemical Sensing Using Sapphire and Silica Optical Fiber Raman Probes

A spatial heterodyne Raman spectrometer (SHRS), constructed using a modular optical cage and lens tube system, is described for use with a commercial silica and a custom single-crystal (SC) sapphire fiber Raman probe. The utility of these fiber-coupled SHRS chemical sensors is demonstrated using 532 nm laser excitation for acquiring Raman measurements of solid (sulfur) and liquid (cyclohexane) Raman standards as well as real-world, plastic-bonded explosives (PBX) comprising 1,3,5- triamino- 2,4,6- trinitrobenzene (TATB) and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) energetic materials. The SHRS is a fixed grating-based dispersive interferometer equipped with an array detector. Each Raman spectrum was extracted from its corresponding fringe image (i.e., interferogram) using a Fourier transform method. Raman measurements were acquired with the SHRS Littrow wavelength set at the laser excitation wavelength over a spectral range of ∼1750 cm −1 with a spectral resolution of ∼8 cm −1 for sapphire and ∼10 cm −1 for silica fiber probes. The large aperture of the SHRS allows much larger fiber diameters to be used without degrading spectral resolution as demonstrated with the larger sapphire collection fiber diameter (330 μm) compared to the silica fiber (100 μm). Unlike the dual silica fiber Raman probe, the dual sapphire fiber Raman probe did not include filtering at the fiber probe tip nearest the sample. Even so, SC sapphire fiber probe measurements produced less background than silica fibers allowing Raman measurements as close as ∼85 cm −1 to the excitation laser. Despite the short lengths of sapphire fiber used to construct the sapphire probe, well-defined, sharp sapphire Raman bands at 420, 580, and 750 cm −1 were observed in the SHRS spectra of cyclohexane and the highly fluorescent HMX-based PBX. SHRS measurements of the latter produced low background interference in the extracted Raman spectrum because the broad band fluorescence (i.e., a direct current, or DC, component) does not contribute to the interferogram intensity (i.e., the alternating current, or AC, component). SHRS spectral resolution, throughput, and signal-to-noise ratio are also discussed along with the merits of using sapphire Raman bands as internal performance references and as internal wavelength calibration standards in Raman measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Summary of Booster Development and Qualification Report

This report outlines booster development work done at Los Alamos National Laboratory from 2007 to present. The booster is a critical link in the initiation train of explosive assemblies, from complex devices like nuclear weapons to conventional munitions. The booster bridges the gap from a small, relatively sensitive detonator to an insensitive, but massive, main charge. The movement throughout the explosives development community is to use more and more insensitive explosive components. With that, more energy is needed out of the booster. It has to initiate reliably, promptly, powerfully and safely. This report is divided into four sections. The first provides a summary of a collaborative effort between LANL, LLNL, and AWE to identify candidate materials and uniformly develop a testing plan for new boosters. Important parameters and the tests required to measure them were defined. The nature of the collaboration and the specific goals of the participating partners has changed over time, but the booster development plan stands on its own merit as a complete description of the test protocol necessary to compare and qualify booster materials, and is discussed in its entirety in this report. The second section describes a project, which began in 2009 with the Department of Defense to develop replacement booster formulations for PBXN-7. Replacement of PBXN-7 was necessary because it contained Triaminotrinitrobenzene (TATB), which was becoming unavailable to the DoD and because it contained Cyclotrimethylenetrinitramine (RDX), which was sensitive and toxic. A LANL-developed explosive, Diaminoazoxyfurazan (DAAF), was an important candidate. This project required any replacement formulation be a drop-in replacement in existing munitions. This project was timely, in that it made use of the collaborative booster development project, and had the additional constraint of matching shock sensitivity. Additionally it needed to be a safety improvement, and a performance improvement, especially at cold temperatures. The requirements of this project necessitated novel test development and a different approach to ranking booster qualities. Results of this project have been documented to the DoD and the relevant portions are included within. The third section of this booster report outlines testing related to main charge initiation merit. Initiability can be evaluated by looking at critical diameter, run distance, and shock sensitivity. Once a booster is initiated, it needs to be powerful enough to initiate the main charge symmetrically and evenly. Main charge initiability is evaluated directly by observing detonation wave symmetry, curvature, and first break out over the surface of a charge. Furthermore it must be insensitive to accidents and insults, and safe and reliable across a range of temperatures. These effects, tests, and results will be discussed individually in the context of DAAF and other explosives similarly tested. The last section provides a conclusion and summary of our experimental work and recommendations for the path forward. References and additional supporting documentation and results are provided in the appendices at the end of this report.

36 MATERIALS SCIENCE↗

Initiation and Detonation Physics on Millimeter Scales

The LLNL Detonation Science Project has a major interest in understanding the physics of detonation on a millimeter scale. This report summarizes the rate stick experiment results of two high explosives. The GO/NO-GO threshold between varying diameters of ultra-fine TATB (ufTATB) and LX-16 were recorded on an electronic streak camera and analyzed. This report summarizes the failure diameters of rate sticks for ufTATB and LX-16. Failure diameter for the ufTATB explosive, with densities at 1.80 g/cc, begin at 2.34 mm (not maintaining detonation velocity over the entire length of the rate stick). ufTATB rate sticks at the larger 3.18 mm diameter maintain a constant detonation velocity over the complete length. The PETN based and LLNL developed explosive, LX-16, with densities at 1.7 g/cc, shows detonation failure between 0.318 mm and 0.365 mm. Additional tests would be required to narrow this failure diameter further. Many of the tested rate sticks were machined using a femtosecond laser focused into a firing tank - in case of accidental detonation.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

PBX 9502 Gas-Generation Throughout Long-Duration Thermal Exposure and Cookoff

When energetic materials are subjected to thermal insult, an event may follow in which the explosive exothermically reacts in an undesirable fashion. This event is known as cookoff, or self-ignition, and understanding how different explosives behave during this event is critical for explosives safety. To further our understanding of how PBX 9502 (95% TATB, 5% Kel-F 800) behaves at cookoff, small scale laboratory experiments were conducted to study the pressure rise created by unconfined samples as they were heated to self-ignition. Collected data included high speed video of deflagration, sample temperature, a time-lapse of thermal damage and expansion, quasi-static pressure during heating, and the dynamic pressure during cookoff. These data provide evidence that this composition remains impermeable through thermal evolution, until internal void pressure overcomes the mechanical strength of the material and drives macro-scale cracking. Previous work reported that PBX 9502 exhibits a pressure-dependent cookoff behavior [1], the cause of which is not entirely understood. The results reported here contribute to an understanding of the underlying behavior which gives rise to the observed pressure dependence.

36 MATERIALS SCIENCE↗

Thylakoid-integrated recombinant Hcf106 participates in the chloroplast twin arginine transport system

The chloroplast twin arginine transport (cpTat) system distinguishes itself as a protein transport pathway by translocating fully folded proteins, using the proton-motive force (PMF) as the sole source of energy. The cpTat pathway is evolutionarily conserved with the Tat pathway found in the plasma membrane of many prokaryotes. The cpTat (Escherichia coli) system uses three proteins, Tha4 (TatA),Hcf106 (TatB), and cpTatC (TatC), to form a transient translocase allowing the pas-sage of precursor proteins. Briefly, cpTatC and Hcf106, with Tha4, form the initial receptor complex responsible for precursor protein recognition and binding in an energy-independent manner, while a separate pool of Tha4 assembles with the pre-cursor-bound receptor complex in the presence the PMF. Analysis by blue-native polyacrylamide gel electrophoresis (BN-PAGE) shows that the receptor complex, in the absence of precursor, migrates near 700 kDa and contains cpTatC and Hcf106with little Tha4 remaining after detergent solubilization. To investigate the role thatHcf106 may play in receptor complex oligomerization and/or stability, systematic cysteine substitutions were made in positions from the N-terminal transmembrane domain to the end of the predicted amphipathic helix of the protein. BN-PAGE analysis allowed us to identify the locations of amino acids in Hcf106 that were critical for interacting with cpTatC. Oxidative cross-linking allowed us to map interactions of the transmembrane domain and amphipathic helix region of Hcf106. In addition, we showed that in vitro expressed, integrated Hcf106 can interact with the precursor signal peptide domain and imported cpTatC, strongly suggesting that a subpopulation of the integrated Hcf106 is participating in competent cpTat complexes.

59 BASIC BIOLOGICAL SCIENCES↗

Elasticity of crystalline molecular explosives

Crystalline molecular explosives are key components of engineered explosive formulations. In precision applications a high degree of consistency and predictability is desired under a range of conditions to a variety of stimuli. Prediction of behaviors from mechanical response and failure to detonation initiation and detonation performance of the material is linked to accurate knowledge of the material structure and first stage of deformation: elasticity. The elastic response of pentaerythritol tetranitrate (PETN), cyclotrimethylene trinitramine (RDX), and cyclotetramethylene tetranitramine (HMX), including aspects of material and measurement variability, and computational methods are described in detail. Experimental determinations of elastic tensors are compared, and an evaluation of sources of error is presented. Furthermore, computed elastic constants are also compared for these materials and for triaminotrinitrobenzene (TATB), for which there are no measurements.

36 MATERIALS SCIENCE↗

Tetrazolyl Triazolotriazine: A New Insensitive High Explosive

A triazolotriazine carbonitrile ( 1 ) was formed by diazotization of 3–amino–5–cyano–1,2,4–triazole followed by treatment with nitroacetonitrile. Cyclization of the C≡N bond with sodium azide results in a tetrazolyl triazolotriazine ( 2 ). Formation of the sodium salt of 2 , followed by metathesis with [PPN][Cl] resulted in the organic salt 3 . Compounds 1 , 2 , and 3 were characterized by elemental analysis and infrared, 1 H, and 13 C{ 1 H} NMR spectroscopy and 1 and 3 were characterized by single–crystal X–ray diffraction. Compound 2 has a density of 1.819 g cm –1 , is thermally stable up to 305 °C, and is insensitive to impact, friction, and electrical discharge. The detonation pressure and velocity of 2 are calculated to be 27.04 GPa and 8.312 km s –1 , respectively, making this a 1,3,5–triamino–2,4,6–trinitrobenzene (TATB) replacement candidate.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Synthesis and Evaluation of 3-Picrylamino-1,2,4-Triazole (PATO) Formulations

3–Picrylamino–1,2,4–triazole (PATO) is a thermally stable explosive invented at Los Alamos National Laboratory (LANL) almost half a century ago. Despite a rapid and high yielding synthesis, performance data for this promising explosive are scant. We prepared material using Coburn's synthesis, and discovered that the particle size distribution and morphology leads to difficulty in pressing formulations to high density. Three formulations were made using glycidyl azide polymer (GAP), FK–800, and Estane 5703/nitroplasticizer (NP) as binders. The maximum pressed density of these formulations was 89 % of theoretical maximum density (TMD). We determined detonation velocity and, for the FK–800 formulation, detonation pressure. Furthermore, the performance of PATO is similar to TATB at equivalent pressed density.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Sensitivity of PBX 9502 to Drilling Operations

Polymer-bonded explosive (PBX) 9502 (95% TATB, 5% Kel-F 800 by weight) is dry-drilled on a CNC milling machine and its thermomechanical response to varying feed rates, drilling speeds, and peck depths with 4 mm and 5 mm diameter drill bits is investigated. The tested samples are affixed to a force sensor that enables recording temporally resolved cutting forces and torques, and a drill-embedded thermocouple yields local temperature data. From the data, an empirical relationship between temperature changes and feed per revolution is developed, which reveals reduced temperatures in higher feed per revolution regimes for PBX 9502. The observed relationship allows extrapolating to temperatures for other hole diameters, indicating increased temperature for smaller diameter drilling across the board. Additional testing was performed with PBX 9501 (95% HMX, 2.5% Estane®, 2.5% BDNPA/BDNPF by weight), albeit over a reduced parameter space, which revealed the opposite behavior for the feed per revolution temperature dependence. It is concluded that both PBX 9502 and PBX 9501 can be dry-drilled efficiently beyond the limits of presently applicable US-DOE standards, where cutting interface temperatures remain far below material critical temperatures. Finally, data reveals that coolant usage in the drilling process for these materials provides a wide safety margin.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗