Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Surface dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Seasat altimeter determination of ocean current variability

An experiment conducted in the Kuroshio Current, east of Japan, has confirmed the ability of radar altimeters of precision on the order of 10 cm, such as that of the Seasat satellite, to measure the small oceanic height variations associated with geostrophic ocean currents. Changes in surface dynamic height were inferred from data gathered by air-expendable barithermographs, which had been dropped to coincide with the Seasat subtrack, for the periods between the flights of September 25 and October 5 and 13, 1978. The changes registered generally agreed to within + or - 10 cm of the height changes observed in the altimeter data.

Bernstein, R. L.↗

Detailed studies of aviation fuel flowability

Six Jet A fuels, with varying compositions, were tested for low temperature flowability in a 190-liter simulator tank that modeled a section of a wing tank of a wide-body commercial airplane. The insulated tank was chilled by circulating coolant through the upper and lower surfaces. Flow-ability was determined as a function of fuel temperature by holdup, the fraction of unflowable fuel remaining in the tank after otherwise complete withdrawal. In static tests with subfreezing tank conditions, hold up varied with temperature and fuel composition. However, a general correlation of two or three classes of fuel type was obtained by plotting holdup as a function of the difference between freezing point and boundary-layer temperature, measured 0.6 cm above the bottom tank surface. Dynamic conditions of vibrations and slosh or rate of fuel withdrawal had very minor effects on holdup. Tests with cooling schedules to represent extreme, cold-day flights showed, at most, slight holdup for any combination of fuel type or dynamic conditions. Tests that superimposed external fuel heating and recirculation during the cooldown period indicates reduced hold up by modification of the low-temperature boundary layer. Fuel heating was just as effective when initiated during the later times of the tests as when applied continuously.

Mehta, H. K.↗

Influence of the Yukon River on the Bering Sea

The relationships between the discharge of the Yukon River to the currents and biological productivity in the northern Bering Sea were studied. Specific objectives were: to develop thermal, sediment, and chlorophyll surface maps using Thematic Mapper (TM) data of the discharge of the Yukon River and the Alaskan Coastal Current during the ice free season; to develop a historical model of the distribution of the Yukon River discharge and the Alaskan Coastal Current using LANDSAT Multispectral band scanner (MSS) and NOAA satellite imagery; and to use high resolution TM data to define the surface dynamics of the front between the Alaskan Coastal Current and the Bering Shelf/Anadyr Current. LANDSAT MSS, TM, and Advanced Very High Resolution Radiometer (AVHRR) data were recorded during the 1985 ice free period. The data coincided with shipboard measurements acquired by Inner Shelf Transfer and Recycling (ISTAR) project scientists. An integrated model of the distribution of turbid water discharged from the Yukon River was compiled. A similar model is also being compiled for the Alaskan Coastal and Bering Shelf/Anadyr water masses based on their thermal expressions seen on AVHRR imagery.

Dean, K.↗

Application of optical interferometry in compressible flows

Interferometry methods were applied to the investigation of steady and unsteady flows in large scale transonic wind tunnels. Holographic interferometry was demonstrated to provide reliable flow visualization and quantitative results for a number of two-dimensional flows. These conclusions were based on extensive comparisons with results obtained by other means. Data obtained on a NACA 64A010 airfoil with an oscillating flap installed in the Ames 11-foot transonic tunnel are presented. Interferograms were recorded at a free stream Mach number of 0.8, flap frequency of 30 Hertz and chord Reynolds numbers of 6.6 x 10 to the 6th and 12.3 x 10 to the 6th. The interferometric results were reduced to dynamic surface pressures, Mach contours and wake flow profiles. A new interferometry method that is capable of providing real-time interferometry data is also discussed.

Bachalo, W. D.↗

Spaceborne imaging radar research in the 90's

The imaging radar experiments on SEASAT and on the space shuttle (SIR-A and SIR-B) have led to a wide interest in the use of spaceborne imaging radars in Earth and planetary sciences. The radar sensors provide unique and complimentary information to what is acquired with visible and infrared imagers. This includes subsurface imaging in arid regions, all weather observation of ocean surface dynamic phenomena, structural mapping, soil moisture mapping, stereo imaging and resulting topographic mapping. However, experiments up to now have exploited only a very limited range of the generic capability of radar sensors. With planned sensor developments in the late 80's and early 90's, a quantum jump will be made in our ability to fully exploit the potential of these sensors. These developments include: multiparameter research sensors such as SIR-C and X-SAR, long-term and global monitoring sensors such as ERS-1, JERS-1, EOS, Radarsat, GLORI and the spaceborne sounder, planetary mapping sensors such as the Magellan and Cassini/Titan mappers, topographic three-dimensional imagers such as the scanning radar altimeter and three-dimensional rain mapping. These sensors and their associated research are briefly described.

Elachi, Charles↗

Influence of the Yukon River on the Bering Sea

The purpose is to use satellite data to study relationships between discharge of the Yukon River to currents and biologic productivity in the northern Bering Sea. Amended specific objectives are: to develop thermal, sediment and chlorophyll surface maps using thematic mapping (TM) data of the discharge of the Yukon River and the Alaska Coastal Current during the ice free season; to develop a historical model of the distribution of the Yukon River discharge and the Alaska Coastal Current using LANDSAT multispectral scanner (MMS) and NOAA satellite imagery; and to use high resolution TM data to define the surface dynamics of the front between the Alaska Coastal Current and the Bering Shelf/Anadyr Current. LANDSAT MSS and TM, and Advanced Very High Resolution Radiometer (AVHRR) data were recorded during the 1985 ice-free period. The satellite data coincided with shipboard measurements acquired by Inner Self Transfer and Recycling scientists. Circumstances were such, that on July 5 and July 22, all three sensors recorded data that has been registered to a common map projection and map base, then contrast stretched, color composited, and density sliced.

Dean, K.↗

One-dimensional wave propagation in rods of variable cross section: A WKBJ solution

As an important step in the characterization of a particular dynamic surface displacement transducer (IQI Model 501), a one-dimensional wave propagation in isotropic nonpiezoelectric and piezoelectric rods of variable cross section are presented. With the use of the Wentzel-Kramers-Brillouin-Jeffreys (WKBJ) approximate solution technique, an approximate formula, which relates the ratio of the amplitudes of a propagating wave observed at any two locations along the rod to the ratio of the cross sectional radii at these respective locations, is derived. The domains of frequency for which the approximate solution is valid are discussed for piezoelectric and nonpiezoelectric materials.

Ochi, Simeon C. U.↗

Analysis of a rotating advanced-technology space station for the year 2025

An analysis is made of several aspects of an advanced-technology rotating space station configuration generated under a previous study. The analysis includes examination of several modifications of the configuration, interface with proposed launch systems, effects of low-gravity environment on human subjects, and the space station assembly sequence. Consideration was given also to some aspects of space station rotational dynamics, surface charging, and the possible application of tethers.

Queijo, M. J.↗

Characterization of noncontact piezoelectric transducer with conically shaped piezoelement

The characterization of a dynamic surface displacement transducer (IQI Model 501) by a noncontact method is presented. The transducer is designed for ultrasonic as well as acoustic emission measurements and, according to the manufacturer, its characteristic features include a flat frequency response range which is from 50 to 1000 kHz and a quality factor Q of less than unity. The characterization is based on the behavior of the transducer as a receiver and involves exciting the transducer directly by transient pulse input stress signals of quasi-electrostatic origin and observing its response in a digital storage oscilloscope. Theoretical models for studying the response of the transducer to pulse input stress signals and for generating pulse stress signals are presented. The characteristic features of the transducer which include the central frequency f sub o, quality factor Q, and flat frequency response range are obtained by this noncontact characterization technique and they compare favorably with those obtained by a tone burst method which are also presented.

Williams, James H., Jr.↗

Modelling the SIR-B image response to partially coherent seas

A mathematical model of transient seas modulated by coherent swells is developed as a Rayleigh-Poisson random process subject to deterministic correlations of scattering sites, as they appear in a time window defined by a SAR's range-Doppler measurements of the surface coordinates. This model of SAR response to sea surface dynamics is discussed as a Fourier domain predictor/corrector of a dynamic motion blur.

Tilley, D. G.↗

Exploratory study of shock reflection near an expansion corner

Experiments were performed at Mach 8 in which a shock was reflected off a low Reynolds number, turbulent boundary layer past an expansion corner. The shock was generated by 2- and 4-deg sharp wedges, and the corner was either 2.5 or 4.25 deg. The inviscid shock reflection was one boundary layer thickness ahead or behind the corner or at the corner itself. All interactions were unseparated. The dynamic surface pressure distributions were examined together with the case of shock reflection on a flat plate. With shock reflection ahead of the corner, the mean surface pressure downstream was attenuated due to the proximity of the corner. With shock reflection downstream of the corner, the surface pressure distribution showed a reduced upstream influence. The highly swept expansion fan produced a surface pressure which rose gently downstream with no minima, unlike in supersonic flows with the same shock-corner separation distance. In many of the interactions, an anomalous pressure peak was found downstream. The surface pressure through the interaction exhibited unsteadiness.

Lu, Frank K.↗

Data assimilation and model evaluation experiment datasets

The Institute for Naval Oceanography, in cooperation with Naval Research Laboratories and universities, executed the Data Assimilation and Model Evaluation Experiment (DAMEE) for the Gulf Stream region during fiscal years 1991-1993. Enormous effort has gone into the preparation of several high-quality and consistent datasets for model initialization and verification. This paper describes the preparation process, the temporal and spatial scopes, the contents, the structure, etc., of these datasets. The goal of DAMEE and the need of data for the four phases of experiment are briefly stated. The preparation of DAMEE datasets consisted of a series of processes: (1) collection of observational data; (2) analysis and interpretation; (3) interpolation using the Optimum Thermal Interpolation System package; (4) quality control and re-analysis; and (5) data archiving and software documentation. The data products from these processes included a time series of 3D fields of temperature and salinity, 2D fields of surface dynamic height and mixed-layer depth, analysis of the Gulf Stream and rings system, and bathythermograph profiles. To date, these are the most detailed and high-quality data for mesoscale ocean modeling, data assimilation, and forecasting research. Feedback from ocean modeling groups who tested this data was incorporated into its refinement. Suggestions for DAMEE data usages include (1) ocean modeling and data assimilation studies, (2) diagnosis and theoretical studies, and (3) comparisons with locally detailed observations.

Lai, Chung-Cheng A.↗

Forced Oscillations of Supported Drops

Oscillations of supported liquid drops are the subject of wide scientific interest, with applications in areas as diverse as liquid-liquid extraction, synthesis of ceramic powders, growing of pure crystals in low gravity, and measurement of dynamic surface tension. In this research, axisymmetric forced oscillations of arbitrary amplitude of viscous liquid drops of fixed volume which are pendant from or sessile on a rod with a fixed or moving contact line and surrounded by an inviscid ambient gas are induced by moving the rod in the vertical direction sinusiodally in time. In this paper, a preliminary report is made on the computational analysis of the oscillations of supported drops that have 'clean' interfaces and whose contact lines remain fixed throughout their motions. The relative importance of forcing to damping can be increased by either increasing the amplitude of rod motion A or Reynolds number Re. It is shown that as the ratio of forcing to damping rises, for drops starting from an initial rest state a sharp increase in deformation can occur when they are forced to oscillate in the vicinity of their resonance frequencies, indicating the incipience of hysteresis. However, it is also shown that the existence of a second stable limit cycle and the occurrence of hysteresis can be observed if the drop is subjected to a so-called frequency sweep, where the forcing frequency is first increased and then decreased over a suitable range. Because the change in drop deformation response is abrupt in the vicinity of the forcing frequencies where hysteresis occurs, it should be possible to exploit the phenomenon to accurately measure the viscosity and surface tension of the drop liquid.

Wilkes, Edward D.↗

Control of Flowing Liquid Films By Electrostatic Fields in Space

A novel type of lightweight space radiator has been proposed which employs internal electrostatic fields to stop coolant leaks from punctures caused by micrometeorites or space debris. Extensive calculations have indicated the feasibility of leak stoppage without film destabilization for both stationary and rotating designs. Solutions of the evolution equation for a liquid-metal film on an inclined plate, using lubrication theory for low Reynolds numbers, Karman-Pohlhausen quadratic velocity profiles for higher Reynolds numbers, and a direct numerical solution are shown. For verification an earth-based falling-film experiment on a precisely-vertical wall with controllable vacuum on either side of a small puncture is proposed. The pressure difference required to start and to stop the leak, in the presence and absence of a strong electric field, will be measured and compared with calculations. Various parameters, such as field strength, film Reynolds number, contact angle, and hole diameter will be examined. A theoretical analysis will be made of the case where the electrode is close enough to the film surface that the electric field equation and the surface dynamics equations are coupled. Preflight design calculations will be made in order to transfer the modified equipment to a flight experiment.

Bankoff, S. George↗

Zonal and Meridional Mass Redistribution in the Tropical Pacific During El Nino Southern Oscillation Events

This note aims at documenting the ENSO-related sea level changes for the whole tropical Pacific, and for the 1979-1996 period which covers numerous El Nino and La Nina events. For this purpose, we rely on (a) 0/450 dbar surface dynamic height anomaly (an alias for sea level) derived from XBT and TOGA-TAO measurements during 1979-1996, (b) TOPEX/Poseidon derived sea level anomaly during 1993-1996, and (c) Murtugudde et al. [1996] model sea level output during 1979-1995.

Delcroix, Thierry↗

Electric Field Induced Interfacial Instabilities

The study of the interface in a charge-free, critical and near-critical binary fluid in the presence of an externally applied electric field is presented. At sufficiently large fields, the interface between the two phases of the binary fluid should become unstable and exhibit an undulation with a predefined wavelength on the order of the capillary length. As the critical point is approached, this wavelength is reduced, potentially approaching length-scales such as the correlation length or critical nucleation radius. At this point the critical properties of the system may be affected. In this paper, the flat interface of a marginally polar binary fluid mixture is stressed by a perpendicular alternating electric field and the resulting instability is characterized by the critical electric field E(sub c) and the pattern observed. The character of the surface dynamics at the onset of instability is found to be strongly dependent on the frequency f of the field applied. The plot of E(sub c) vs. f for a fixed temperature shows a sigmoidal shape, whose low and high frequency limits are well described by a power-law relationship, E(sub c) = epsilon(exp zeta) with zeta = 0.35 and zeta = 0.08, respectively. The low-limit exponent compares well with the value zeta = 4 for a system of conducting and non-conducting fluids. On the other hand, the high-limit exponent coincides with what was first predicted by Onuki. The instability manifests itself as the conducting phase penetrates the non-conducting phase. As the frequency increases, the shape of the pattern changes from an array of bifurcating strings to an array of column-like (or rod-like) protrusions, each of which spans the space between the plane interface and one of the electrodes. For an extremely high frequency, the disturbance quickly grows into a parabolic cone pointing toward the upper plate. As a result, the interface itself changes its shape from that of a plane to that of a high sloping pyramid.

Kusner, Robert E.↗

Measurement of Separated Flow Structures Using a Multiple-Camera DPIV System

A novel multiple-camera system for the recording of digital particle image velocimetry (DPIV) images acquired in a two-dimensional separating/reattaching flow is described. The measurements were performed in the NASA Langley Subsonic Basic Research Tunnel as part of an overall series of experiments involving the simultaneous acquisition of dynamic surface pressures and off-body velocities. The DPIV system utilized two frequency-doubled Nd:YAG lasers to generate two coplanar, orthogonally polarized light sheets directed upstream along the horizontal centerline of the test model. A recording system containing two pairs of matched high resolution, 8-bit cameras was used to separate and capture images of illuminated tracer particles embedded in the flow field. Background image subtraction was used to reduce undesirable flare light emanating from the surface of the model, and custom pixel alignment algorithms were employed to provide accurate registration among the various cameras. Spatial cross correlation analysis with median filter validation was used to determine the instantaneous velocity structure in the separating/reattaching flow region illuminated by the laser light sheets. In operation the DPIV system exhibited a good ability to resolve large-scale separated flow structures with acceptable accuracy over the extended field of view of the cameras. The recording system design provided enhanced performance versus traditional DPIV systems by allowing a variety of standard and non-standard cameras to be easily incorporated into the system.

Humphreys, William M., Jr.↗

Science Issues Associated with the Use of a Microfluidic Chip Designed Specifically for Protein Crystallization

The Iterative Biological Crystallization team in partnership with Caliper Technologies has produced a prototype microfluidic chip for batch crystallization that has been designed and tested. The chip is designed for the mixing and dispensing of up to five solutions with possible variation of the recipe being delivered to two growth wells. Developments that have led to the successful on-chip crystallization of a few model proteins have required investigative insight into many different areas, including fluid mixing dynamics, surface treatments, quantification and fidelity of reagent delivery. This presentation will encompass the ongoing studies and data accumulated toward these efforts.

Holmes, Anna M.↗