Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Strain improvement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Imide modified epoxy matrix resins

High char yield epoxy using novel bisimide amines (BIA's) as curing agents with a state of the art epoxy resin was developed. Stoichiometric quantities of the epoxy resin and the BIA's were studied to determine the cure cycle required for preparation of resin specimens. The bisimide cured epoxies were designated IME's (imide modified epoxy). The physical, thermal and mechanical properties of these novel resins were determined. The levels of moisture absorption exhibited by the bisimide amine cured expoxies (IME's) were considerably lower than the state of the art epoxies. The strain-to-failure of the control resin system was improved 25% by replacement of DDS with 6F-DDS. Each BIA containing resin exhibited twice the char yield of the control resin MY 720/DDS. Graphite fiber reinforced control (C) and IME resins were fabricated and characterized. Two of the composite systems showed superior properties compared to the other Celion 6000/IME composite systems and state of the art graphite epoxy systems. The two systems exhibited excellent wet shear and flexural strengths and moduli at 300 and 350 F.

Scola, D. A.↗
NASA NTRS1986

Effects of thermal cycling on graphie-fiber-reinforced 6061 aluminum

Graphite-reinforced aluminum alloy metal-matrix composites are among materials being considered for structural components in dimensionally stable space structures. This application requires materials with low values of thermal expansions and high specific stiffnesses. They must remain stable during exposures to the space environment for periods extending to 20 years. The effects of thermal cycling on the thermal expansion behavior and mechanical properties of Thornel P100 graphite 6061 aluminum composites, as fabricated and after thermal processing to eliminate thermal strain hysteresis, have been investigated. Two groups of composites were studied: one was fabricated by hot roll bonding and the other by diffusion bonding. Processing significantly reduced strain hysteresis during thermal cycling in both groups and improved the ultimate tensile strength and modulus in the diffusion-bonded composites. Thermal cycling stabilized the as-fabricated composites by reducing the residual fabrication stress and increased the matrix strength by metallurgical aging. Thermal expansion behavior of both groups after processing was insensitive to thermal cycling. Data scatter was too large to determine effects of thermal cycling on the mechanical properties. The primary effects of processing and thermal cycling can be attributed to changes in the metallurgical condition and stress state of the matrix.

Dries, G. A.↗
NASA NTRS1988

Stress concentration around circular hole in a composite material specimen representative of the X-29A forward-swept wing aircraft

The theory of anisotropic elasticity was used to evaluate the anisotropic stress concentration factors of a composite laminated plate containing a small circular hole. This advanced composite material was used to manufacture the X-29A forward swept wing. Observe that the usual isotropic material stress concentration factor is three. However, for composite material, it was found that the anisotropic stress concentration factor is no longer constant, and that the locations of maximum tangential stress points could shift by changing the fiber orientation with respect to the loading axis. The analysis showed that through the lamination process, the stress concentration factor could be drastically reduced, and therefore the structural performance could be improved. Both the mixture rule approach and the constant strain approach were used to calculate the stress concentration factor. The results predicted by the mixture rule approach were about 20 percent deviate from the experimental data. However, the results predicted by the constant strain approach matched the testing data very well. This showed the importance of the inplane shear effect on the evaluation of stress concentration factor for the X-29A composite plate.

Yeh, Hsien-Yang↗
NASA NTRS1988

Temperature effect on stress concentration around circular hole in a composite material specimen representative of X-29A forward-swept wing aircraft

The theory of anisotropic elasticity was used to evaluate the anisotropic stress concentration factors of a composite laminated plate containing a small circular hole. This advanced composite was used to manufacture the X-29A forward-swept wing. It was found for composite material, that the anisotropic stress concentration is no longer a constant, and that the locations of maximum tangential stress points could shift by changing the fiber orientation with respect to the loading axis. The analysis showed that through the lamination process, the stress concentration factor could be reduced drastically, and therefore the structural performance could be improved. Both the mixture rule approach and the constant strain approach were used to calculate the stress concentration factor of room temperature. The results predicted by the mixture rule approach were about twenty percent deviate from the experimental data. However, the results predicted by the constant strain approach matched the testing data very well. This showed the importance of the inplane shear effect on the evaluation of the stress concentration factor for the X-29A composite plate.

Yeh, Hsien-Yang↗
NASA NTRS1992

Processing of three-dimensional particle tracking velocimetry data

An interpolation method is presented which allows the accurate evaluation of a three-dimensional velocity field. The method can also be used to directly evaluate the strain rate and vorticity components. The required smoothing to improve accuracy is shown to be robust, and continuity is satisfied. The errors associated with the method are estimated at less than 1 percent for velocity vector data and less than 5 percent for vorticity. The method has application in the analysis of turbulence data from three-dimensional particle imaging velocimetry.

Liburdy, James A.↗
NASA NTRS1994

Modeling time-dependent corrosion fatigue crack propagation in 7000 series aluminum alloys

Stress corrosion cracking and corrosion fatigue experiments were conducted with the susceptible S-L orientation of AA7075-T651, immersed in acidified and inhibited NaCl solution, to provide a basis for incorporating environmental effects into fatigue crack propagation life prediction codes such as NASA FLAGRO. This environment enhances da/dN by five to ten-fold compared to fatigue in moist air. Time-based crack growth rates from quasi-static load experiments are an order of magnitude too small for accurate linear superposition prediction of da/dN for loading frequencies above 0.001 Hz. Alternate methods of establishing da/dt, based on rising-load or ripple-load-enhanced crack tip strain rate, do not increase da/dt and do not improve linear superposition. Corrosion fatigue is characterized by two regimes of frequency dependence; da/dN is proportional to f(exp -1) below 0.001 Hz and to F(exp 0) to F(exp -0.1) for higher frequencies. Da/dN increases mildly both with increasing hold-time at K(sub max) and with increasing rise-time for a range of loading waveforms. The mild time-dependence is due to cycle-time-dependent corrosion fatigue growth. This behavior is identical for S-L nd L-T crack orientations. The frequency response of environmental fatigue in several 7000 series alloys is variable and depends on undefined compositional or microstructural variables. Speculative explanations are based on the effect of Mg on occluded crack chemistry and embritting hydrogen uptake, or on variable hydrogen diffusion in the crack tip process zone. Cracking in the 7075/NaCl system is adequately described for life prediction by linear superposition for prolonged load-cycle periods, and by a time-dependent upper bound relationship between da/dN and delta K for moderate loading times.

Mason, Mark E.↗
NASA NTRS2006

STRANAL-PMC Version 2.0

Version 2.0 of the Strain Rate Dependent Analysis of Polymer Matrix Composites (STRANAL-PMC) software has been released. A prior version was reported in Analyzing Loads and Strains in Polymer- Matrix Composites (LEW-17227), NASA Tech Briefs, Vol. 26, No. 11 (November 2002), page 36. To recapitulate: Modified versions of constitutive equations of viscoplasticity of metals are used to represent deformation of a polymeric matrix. The equations are applied in a micromechanical approach, proceeding upward from slices of unit cells, through the ply level, to the laminate level. The constitutive equations are integrated in time by a Runge- Kutta technique. To predict the ultimate strength of each composite ply, failure criteria are implemented within the micromechanics. The inputs to STRANAL-PMC are the laminate geometry, properties of the fiber and matrix materials, and applied stress or strain versus time. The outputs are time-dependent stresses and strains at the slice, ply, and laminate levels. The improvements in version 2.0 include more rigorous representation of hydrostatic- stress effects in the matrix, refinement and extension of ply failure models, and capabilities to analyze transverse shear stresses. Version 2.0 can be implemented as a material-model code within transient dynamic finite-element codes.

Goldberg, Robert↗
NASA NTRS2015

Compliant Electrode and Composite Material for Piezoelectric Wind and Mechanical Energy Conversions

A thin film device for harvesting energy from wind. The thin film device includes one or more layers of a compliant piezoelectric material formed from a composite of a polymer and an inorganic material, such as a ceramic. Electrodes are disposed on a first side and a second side of the piezoelectric material. The electrodes are formed from a compliant material, such as carbon nanotubes or graphene. The thin film device exhibits improved resistance to structural fatigue upon application of large strains and repeated cyclic loadings.

Chen, Bin↗
NASA NTRS2023

Modeling of Response of Thermoplastic Composites Under High Energy Impact

This work investigates the response of a thermoplastic panel under high energy ballistic impact. The composite material system is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK3). Several high energy dynamic impact tests were performed where an aluminum projectile impacted various panels at different impact velocities. For this work, the test performed at an impact velocity of 73.2 m/s was investigated. The projectile rebounded upon impact, and the damage to the panel was characterized through ultrasonic and CT-scanning. Response of the panel under impact and the associated damage is discussed. Numerical simulation of the impact process was performed using the LS-DYNA® computer code [1] with a new material model MAT_COMPOSITE_DAMAGE_DGD (MAT 299), a modification over MAT 261 material model in terms of an improved representation of damage coupling and additional capability for strain rate effects. Delaminations were modeled using cohesive zone contact formulation in LS-DYNA®, wherein the mixed-mode fracture is captured via the Benzegaggh-Kenane (B-K) mode-dependent fracture energy interpolation law. Simulation of this impact test demonstrates a good match of results in terms of panel deflection and panel-projectile interactions. The overall extent of delaminations was under-predicted by the simulation. This work forms the basis to model tests performed at higher velocities, involving projectile penetration of panel.

Composite Materials↗
NASA NTRS1984

Effect of impact damage and open holes on the compression strength of tough resin/high strain fiber laminates

Structural damage and design-based inclusions such as cutouts can reduce significantly the strength of graphite-epoxy laminates. One composite mechanics research activity at the Langley Research Center is to assess and improve the performance of composite structures in strength are common to both tension and compression loaded laminates; however, the problem associated with compression performance is the most illusive to solve. Compression failure involves both shear crippling and delamination modes. Several graphite-epoxy material systems proposed for improved damage-tolerance were studied. Material parameters included both tough resin formulations and high strain fibers.

Williams, J. G.↗
NASA NTRS1991

Improved compression buckling for rectangular composite plates by stiffness tailoring

Buckling resistance is often a controlling criterion in the design of structural elements. Design concepts that lead to increased buckling loads (or strains) can directly lower the structural cost and/or weight by a number of means. This study quantifies the improvements that can be achieved in compression buckling loads of rectangular composite plates by using a simple stiffness tailoring concept. The approach is to position the unidirectional lamina through the thickness and over the planform of the plate so that the buckling load is increased with no loss in in-plane stiffness or increase in weight. Finite element analyses have been used to determine the effects of tailoring on the buckling load of plates with various boundary conditions, aspect ratios, thicknesses, and membrane stiffnesses. Increases in buckling loads (or strains) of nearly 200 percent over the uniform plate buckling loads are shown possible with this tailoring concept.

Biggers, Sherrill B.↗
NASA NTRS2010

Improvement in the Shape Memory Response of Ti50.5Ni24.5Pd25 High-Temperature Shape Memory Alloy with Scandium Microalloying

A Ti(50.5)Ni(24.5)Pd25 high-temperature shape memory alloy (HTSMA) is microalloyed with 0.5 at. pct scandium (Sc) to enhance its shape-memory characteristics, in particular, dimensional stability under repeated thermomechanical cycles. For both Ti(50.5)Ni(24.5)Pd25 and the Sc-alloyed material, differential scanning calorimetry is conducted for multiple cycles to characterize cyclic stability of the transformation temperatures. The microstructure is evaluated using electron microscopy, X-ray diffractometry, and wavelength dispersive spectroscopy. Isobaric thermal cycling experiments are used to determine transformation temperatures, dimensional stability, and work output as a function of stress. The Sc-doped alloy displays more stable shape memory response with smaller irrecoverable strain and narrower thermal hysteresis than the baseline ternary alloy. This improvement in performance is attributed to the solid solution hardening effect of Sc.

Atli, K. C.↗
NASA NTRS1995

Assessment of microalloying effects on the high temperature fatigue behavior of NiAl

Binary NiAl suffers from a lack of strength and poor creep properties at and above 1000 K. Poor creep resistance in turn affects low cycle fatigue (LCF) lives at low strain ranges due to the additional interactions of creep damage. One approach for improving these properties involved microalloying with either Zr or N. As an integral part of a much larger alloying program the low cycle fatigue behavior of Zr and N doped nickel aluminides produced by extrusion of prealloyed powders has been investigated. Strain controlled LCF tests were performed in air at 1000 K. The influence of these microalloying additions on the fatigue life and cyclic stress response of polycrystalline NiAl are discussed.

Noebe, R. D.↗
NASA NTRS1974

Glass fiber addition strengthens low-density ablative compositions

Approximately 15% of E-glass fibers was added to compositions under test and greatly improved char stability. Use of these fibers also reduced thermal strains which, in turn, minimized char shrinkage and associated cracks, subsurface voids, and disbonds. Increased strength allows honeycomb core reinforcement to be replaced by equivalent amount of glass fibers.

Chandler, H. H.↗
NASA NTRS1975

SSME structural computer program development: BOPACE theoretical manual, addendum

An algorithm developed and incorporated into BOPACE for improving the convergence and accuracy of the inelastic stress-strain calculations is discussed. The implementation of separation of strains in the residual-force iterative procedure is defined. The elastic-plastic quantities used in the strain-space algorithm are defined and compared with previous quantities.

Source record↗
NASA NTRS1983

Critical composite joint subcomponents: Analysis and test results

This program has been conducted to develop the technology for critical structural joints of a composite wing structure meeting design requirements for a 1990 commercial transport aircraft. A prime objective of the program was to demonstrate the ability to reliably predict the strength of large bolted composite joints. Load sharing between bolts in multirow joints was computed by a nonlinear analysis program (A4FJ) which was used both to assess the efficiency of different joint design concepts and to predict the strengths of large test articles representing a section from a wing root chord-wise splice. In most cases, the predictions were accurate to within a few percent of the test results. A highlight of these tests was the consistent ability to achieve gross-section failure strains on the order of 0.005 which represents a considerable improvement over the state of the art. The improvement was attained largely as the result of the better understanding of the load sharing in multirow joints provided by the analysis. The typical load intensity on the structural joints was about 40 to 45 thousand pound per inch in laminates having interspersed 37 1/2-percent 0-degree plies, 50-percent + or - 45-degrees plies and 12 1/2-percent 90-degrees plies. The composite material was Toray 300 fiber and Ciba-Geigy 914 resin, in the form of 0.010-inch thick unidirectional tape.

Bunin, B. L.↗
NASA NTRS2004

Tethers as Debris: Simulating Impacts of Kevlar Tethers on Shuttle Tiles

In a previous paper I examined the effects of impacts of polymer tethers on aluminum plates using the SPHC hydrodynamic code. In this paper I apply tether models to a new target - models of Space Shuttle tiles developed during the STS 107 accident investigation. In this three-dimensional simulation, a short tether fragment strikes a single tile supported on an aluminum backing plate. A tile of the LI-900 material is modeled. Penetration and damage to the tile and the backwall are characterized for three normal impact velocities. The tether is modeled as a bundle of eight 1-mm strands, with the bundle having dimensions 2-mm x 4-mm x 20-cm. The bulk material properties used are those of Kevlar(TradeMark) 49, for which a Mie-Gruneisen multiphase equation of state (eos) is used. In addition, the strength model is applied in a linear sense, such that tensile loads along the strand length are supported, but there is no strength in the lateral directions. Tile models include the various layers making up the tile structure. The outermost layer is a relatively dense borosilicate glass, known as RCG, 0.5-mm thick. The RCG layer is present on the top and four sides of the tile. Below this coating is the bulk of the tile, 1.8- in thick, made of LI-900, a product consisting of rigidized fiberous silica with a density of 9 lWft3. Below the main insulating layer is a bottom layer of the same material that has been treated to increase its density by approximately 69% to improve its strength. This densified layer is bonded to a Strain Isolation Pad (SIP), modeled as a refractory felt fabric. The SIP is bonded to an aluminum 2024 wall 0.1-in thick. The tile and backwall materials use a Me-Gruneisen multiphase eos, with the exception of the SIP felt, which uses a fabric equation of state. Fabrics must be crushed to the full bulk material density before bulk material properties and a Mie-Gruneisen eos are applied. Tether fragment impact speeds of 3,7, and 10 km/s are simulated, with impact velocities normal to the tile face. Damage results are presented in tabular format.

Evans, Steven W.↗
NASA NTRS2014

Theoretical Development of an Orthotropic Elasto-Plastic Generalized Composite Material Model

The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites is becoming critical as these materials are gaining increased usage in the aerospace and automotive industries. While there are several composite material models currently available within LSDYNA (Livermore Software Technology Corporation), there are several features that have been identified that could improve the predictive capability of a composite model. To address these needs, a combined plasticity and damage model suitable for use with both solid and shell elements is being developed and is being implemented into LS-DYNA as MAT_213. A key feature of the improved material model is the use of tabulated stress-strain data in a variety of coordinate directions to fully define the stress-strain response of the material. To date, the model development efforts have focused on creating the plasticity portion of the model. The Tsai-Wu composite failure model has been generalized and extended to a strain-hardening based orthotropic yield function with a nonassociative flow rule. The coefficients of the yield function, and the stresses to be used in both the yield function and the flow rule, are computed based on the input stress-strain curves using the effective plastic strain as the tracking variable. The coefficients in the flow rule are computed based on the obtained stress-strain data. The developed material model is suitable for implementation within LS-DYNA for use in analyzing the nonlinear response of polymer composites.

Polymer Matrix Composites↗