Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Modeling the potential of screen printed front junction CZ silicon solar cell with tunnel oxide passivated back contact

Carrier selective passivated contacts composed of thin oxide, n + polycrystalline Si and metal on top of a n-Si absorber can significantly lower the recombination current density (J orear ≤8 fA/cm 2 ) under the contact while providing excellent specific contact resistance (5–10 mΩ-cm 2 ); 25.1% efficient small area cells with photolithography front contacts on boron doped selective emitter and Fz wafers have been achieved by Fraunhofer ISE using their tunnel oxide passivated contact (TOPCon) approach. This paper shows a methodology to model such passivated contact cells using Sentaurus device model, which involves replacing the TOPCon region by carrier selective electron and hole recombination velocities to match the measured J orear of the TOPCon region as well as all the light IV values of the cell. We first validated the methodology by modeling a 24.9% reference cell. The model was then extended to assess the efficiency potential of large area TOPCon cells on commercial grade n-type Cz material with screen-printed front contacts. To use realistic input parameters, a 21% n-type PERT cell was fabricated on Cz wafer (5 Ω-cm, 1.5-ms lifetime). Modeling showed that the cell efficiency will improve to only 21.6% if the back of this cell is replaced by the above TOPCon, and the performance is limited by the homogenous emitter. Efficiency was then modeled to improve to 22.6% with the implementation of selective emitter (150/20 Ω/sq). Lastly, it is shown that screen printing of 40-µm-wide lines and improved bulk material (10 Ω-cm, 3-ms lifetime) can raise the single side TOPCon Cz cell efficiency to 23.2%.

14 SOLAR ENERGY↗

GaAs/InGaAsN heterostructures for multi-junction solar cells

Solar-cell heterostructures based on GaAs/InGaAsN materials with an InAs/GaAsN superlattice, grown by molecular beam epitaxy, are studied. A p-GaAs/i-(InAs/GaAsN)/n-GaAs p–i–n test solar cell with a 0.9-μm-thick InGaAsN layer has an open-circuit voltage of 0.4 V (1 sun, AM1.5G) and a quantum efficiency of >0.75 at a wavelength of 940 nm (at zero reflection loss), which corresponds to a short-circuit current of 26.58 mA/cm{sup 2} (AM1.5G, 100 mW/cm{sup 2}). The high open-circuit voltage demonstrates that InGaAsN can be used as a material with a band gap of 1 eV in four-cascade solar cells.

36 MATERIALS SCIENCE↗

High external quantum efficiency and fill-factor InGaN/GaN heterojunction solar cells grown by NH 3 -based molecular beam epitaxy

High external quantum efficiency (EQE) p-i-n heterojunction solar cellsgrown by NH 3 -based molecular beam epitaxy are presented. EQE values including optical losses are greater than 50% with fill-factors over 72% when illuminated with a 1 sun AM0 spectrum. Optical absorptionmeasurements in conjunction with EQE measurements indicate an internal quantum efficiency greater than 90% for the InGaN absorbing layer. By adjusting the thickness of the top p-type GaN window contact layer, it is shown that the short-wavelength (<365 nm) quantum efficiency is limited by the minority carrier diffusion length in highly Mg-doped p-GaN.

14 SOLAR ENERGY↗

Solar power satellites - Heat engine or solar cells

A solar power satellite is the energy-converting element of a system that can deliver some 10 GW of power to utilities on the earth's surface. We evaluated heat engines and solar cells for converting sunshine to electric power at the satellite. A potassium Rankine cycle was the best of the heat engines, and 50 microns thick single-crystal silicon cells were the best of the photovoltaic converters. Neither solar cells nor heat engines had a clear advantage when all factors were considered. The potassium-turbine power plant, however, was more difficult to assemble and required a more expensive orbital assembly base. We therefore based our cost analyses on solar-cell energy conversion, concluding that satellite-generated power could be delivered to utilities for around 4 to 5 cents a kWh.

Oman, H.↗

Nanostructured Electrodes For Organic Bulk Heterojunction Solar Cells: Model Study Using Carbon Nanotube Dispersed Polythiophene-fullerene Blend Devices

We test the feasibility of using nanostructured electrodes in organic bulk heterojunction solar cells to improve their photovoltaic performance by enhancing their charge collection efficiency and thereby increasing the optimal active blend layer thickness. As a model system, small concentrations of single wall carbon nanotubes are added to blends of poly(3-hexylthiophene): [6,6]-phenyl-C{sub 61}-butyric acid methyl ester in order to create networks of efficient hole conduction pathways in the device active layer without affecting the light absorption. The nanotube addition leads to a 22% increase in the optimal blend layer thickness from 90 nm to 110 nm, enhancing the short circuit current density and photovoltaic device efficiency by as much as {approx}10%. The associated incident-photon-to-current conversion efficiency for the given thickness also increases by {approx}10% uniformly across the device optical absorption spectrum, corroborating the enhanced charge carrier collection by nanostructured electrodes.

14 SOLAR ENERGY↗

Low-temperature processed high-performance flexible perovskite solar cells via rationally optimized solvent washing treatments

High performance planar-heterojunction (PHJ) perovskite (CH3NH3PbI3) solar cells fabricated through lowtemperature annealing are demonstrated. Simple spin-coating with an optimized solvent washing process readily forms homogeneous and crystalline perovskite thin films. The perovskite films fabricated via this solvent washing process show a low dependence on annealing temperature in achieving high crystallinity and large grain size, prerequisites for high efficiency perovskite solar cells. The solar cell device fabricated by solvent washing and 100 C annealing exhibited a high power conversion efficiency (PCE) over 14% with high short circuit current density (JSC) of 19.3 mA cm 2 and fill factor (FF) of 0.80. More importantly, the device annealed at low temperature (<90 C) also yields high PCEs of over 12%. This enables us to fabricate flexible solar cells at low-temperatures with promising PCE as high as 9.43%. This study demonstrates that this optimized solvent washing process is highly relevant for low-cost rollto-roll (R-2-R) processing of high performance perovskite solar cells.

14 SOLAR ENERGY↗

Light Trapping for High Efficiency Heterojunction Crystalline Si Solar Cells: Preprint

Light trapping plays an important role to achieve high short circuit current density (Jsc) and high efficiency for amorphous/crystalline Si heterojunction solar cells. Si heterojunction uses hydrogenated amorphous Si for emitter and back contact. This structure of solar cell posses highest open circuit voltage of 0.747 V at one sun for c-Si based solar cells. It also suggests that over 25%record-high efficiency is possible with further improvement of Jsc. Light trapping has two important tasks. The first one is to reduce the surface reflectance of light to zero for the solar spectrum that Si has a response. The second one is to increase the effective absorption length to capture all the photon. For Si heterojunction solar cell, surface texturing, anti-reflectance indium tinoxides (ITO) layer at the front and back are the key area to improve the light trapping.

14 SOLAR ENERGY↗

Roll-to-Roll Printing of Perovskite Solar Cells

High efficiency combined with transformative roll-to-roll (R2R) printability makes metal halide perovskite-based solar cells the most promising solar technology to address the terawatt challenge of the future energy demand. However, translation from lab-scale deposition solution processing techniques to large-scale R2R methods has typically led to reduced photovoltaic performance. Here, we demonstrate large-scale, highly crystalline, uniaxially oriented, smooth perovskite films printed at room temperature and in the ambient environment. Confirmed with high speed in situ X-ray diffraction measurements, the perovskite films reach 98% of relative crystallinity at room temperature and display high texture within 1 s of the coating. We demonstrate an all-blade-coated metal halide perovskite cell with power conversion efficiency (PCE) up to 19.6%, a slot-die coated cell with a PCE of 17.3%, and a partially R2R slot-die coated flexible glass-based cell efficiency of 14.1%. As a result the developed printing method can be applied to diverse perovskite compositions, enabling a variety of bandgaps to pave the way for the future R2R printing of highly efficient perovskite–perovskite tandem cells.

14 SOLAR ENERGY↗

Optical and Electronic Losses Arising from Physically Mixed Interfacial Layers in Perovskite Solar Cells

Perovskite solar cell device performance is affected by optical and electronic losses. To minimize these losses in solar cells, it is important to identify their sources. Here, we report the optical and electronic losses arising from physically mixed interfacial layers between the adjacent component materials in highly efficient two terminal (2T) all-perovskite tandem, single junction wide-bandgap, and single junction narrow-bandgap perovskite-based solar cells. Physically mixed interfacial layers as the sources of optical and electronic losses are identified from spectroscopic ellipsometry measurements and data analysis followed by comparisons of simulated and measured external quantum efficiency spectra. Parasitic absorbance in the physically mixed regions between silver metal electrical contacts and electron transport layers (ETLs) near the back contact and a physical mixture of commercial indium tin oxide and hole transport layers (HTL) near the front electrical contact lead to substantial optical loss. Here, a lower-density void + perovskite nucleation layer formed during perovskite deposition at the interface between the perovskite absorber layer and the HTL causes electronic losses due to incomplete collection of photogenerated carriers likely originating from poor coverage and passivation of the initially nucleating grains.

14 SOLAR ENERGY↗

III-nitride core-shell nanowire arrayed solar cells

A solar cell based on a III-nitride hybrid nanowire-film architecture is demonstrated. It consists of a vertically-aligned array of InGaN/GaN multi-quantum well core-shell nanowires, electrically connected by a coalesced p-type InGaN canopy layer. This hybrid structure allows for standard planar device processing, solving an important challenge with nanowire device integration. It also enables various advantages such as higher indium composition InGaN layers via elastic strain relief, efficient carrier collection through thin layers, and enhanced light trapping. This proof-of-concept nanowire-based device presents a path forward for high-efficiency III-nitride solar cells. Fabricated III-nitride nanowire solar cells exhibit a photoresponse out to 2.1eV and short circuit current density of ~1 mA/cm 2 (1 sun AM1.5G).

Wierer Jr., Jonathan J.↗

17.1%-Efficient Multi-Scale-Textured Black Silicon Solar Cells without Dielectric Antireflection Coating: Preprint

In this work we present 17.1%-efficient p-type single crystal Si solar cells with a multi-scale-textured surface and no dielectric antireflection coating. Multi-scale texturing is achieved by a gold-nanoparticle-assisted nanoporous etch after conventional micron scale KOH-based pyramid texturing (pyramid black etching). By incorporating geometric enhancement of antireflection, this multi-scaletexturing reduces the nanoporosity depth required to make silicon 'black' compared to nanoporous planar surfaces. As a result, it improves short-wavelength spectral response (blue response), previously one of the major limiting factors in 'black-Si' solar cells. With multi-scale texturing, the spectrum-weighted average reflectance from 350- to 1000-nm wavelength is below 2% with a 100-nm deepnanoporous layer. In comparison, roughly 250-nm deep nanopores are needed to achieve similar reflectance on planar surface. Here, we characterize surface morphology, reflectivity and solar cell performance of the multi-scale textured solar cells.

14 SOLAR ENERGY↗