Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SCANDIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Cyclotron production of 43Sc and 44gSc from enriched 42CaO, 43CaO, and 44CaO targets

Introduction: 43 Sc and 44g Sc are both positron-emitting radioisotopes of scandium with suitable half-lives and favorable positron energies for clinical positron emission tomography (PET) imaging. Irradiation of isotopically enriched calcium targets has higher cross sections compared to titanium targets and higher radionuclidic purity and cross sections than natural calcium targets for reaction routes possible on small cyclotrons capable of accelerating protons and deuterons. Methods: In this work, we investigate the following production routes via proton and deuteron bombardment on CaCO 3 and CaO target materials: 42 Ca(d,n) 43 Sc, 43 Ca(p,n) 43 Sc, 43 Ca(d,n) 44g Sc, 44 Ca(p,n) 44g Sc, and 44 Ca(p,2n) 43 Sc. Radiochemical isolation of the produced radioscandium was performed with extraction chromatography using branched DGA resin and apparent molar activity was measured with the chelator DOTA. The imaging performance of 43 Sc and 44g Sc was compared with 18 F, 68 Ga, and 64 Cu on two clinical PET/CT scanners. Discussion: The results of this work demonstrate that proton and deuteron bombardment of isotopically enriched CaO targets produce high yield and high radionuclidic purity 43 Sc and 44g Sc. Laboratory capabilities, circumstances, and budgets are likely to dictate which reaction route and radioisotope of scandium is chosen.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vertical and Lateral Etch Survey of Ferroelectric AlN/Al 1-x Sc x N in Aqueous KOH Solutions

Due to their favorable electromechanical properties, such as high sound velocity, low dielectric permittivity and high electromechanical coupling, Aluminum Nitride (AlN) and Aluminum Scandium Nitride (Al 1-x Sc x N) thin films have achieved widespread application in radio frequency (RF) acoustic devices. The resistance to etching at high scandium alloying, however, has inhibited the realization of devices able to exploit the highest electromechanical coupling coefficients. In this work, we investigated the vertical and lateral etch rates of sputtered AlN and Al 1-x Sc x N with Sc concentration x ranging from 0 to 0.42 in aqueous potassium hydroxide (KOH). Etch rates and the sidewall angles were reported at different temperatures and KOH concentrations. We found that the trends of the etch rate were unanimous: while the vertical etch rate decreases with increasing Sc alloying, the lateral etch rate exhibits a V-shaped transition with a minimum etch rate at x = 0.125. By performing an etch on an 800 nm thick Al 0.875 Sc 0.125 N film with 10 wt% KOH at 65 °C for 20 min, a vertical sidewall was formed by exploiting the ratio of the {$10\overline{11}$ planes and {$1\overline{1}00$ planes etch rates. This method does not require preliminary processing and is potentially beneficial for the fabrication of lamb wave resonators (LWRs) or other microelectromechanical systems (MEMS) structures, laser mirrors and Ultraviolet Light-Emitting Diodes (UV-LEDs). It was demonstrated that the sidewall angle tracks the trajectory that follows the {$\overline{1}2\overline{12}$ of the hexagonal crystal structure when different c/a ratios were considered for elevated Sc alloying levels, which may be used as a convenient tool for structure/composition analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A biosorption-based approach for selective extraction of rare earth elements from coal byproducts

Coal byproducts could be a promising feedstock to alleviate the supply risk of critical rare earth elements (REEs) due to their abundance and REE content. Herein, we investigated the economic and environmental potential of producing REEs from coal fly ash and lignite through an integrated process of leaching, biosorption, and oxalic precipitation based on experimental data and modeling results. Two microbe immobilization systems (PEGDA) microbe beads and Si sol-gels) were examined for their efficiency in immobilizing Arthrobacter nicotianae to selectively recover REEs. Techno-economic analysis revealed that North Dakota lignite could be a profitable feedstock when Si sol-gel is used due to its high cell loading and REE adsorption capacity. Life cycle analysis revealed that Si sol-gel based biosorption could be more environmental friendly than the prevailing REE production in China due to use of less toxic chemicals. However, fly ash sourced from Powder River Basin coals was neither profitable or environmentally sustainable, primarily due to low solublity of high-value scandium at an economical pulp density (100 ash/L). To further improve the proposed biotechnology, future research could focus on scandium recovery, leaching efficiency, and microbe carriers.

20 FOSSIL-FUELED POWER PLANTS↗

Synthesis and Characterization of MgCr 2 S 4 Thiospinel as a Potential Magnesium Cathode

Magnesium-ion batteries are a promising energy storage technology because of their higher theoretical energy density and lower cost of raw materials. Among the major challenges has been the identification of cathode materials that demonstrate capacities and voltages similar to lithium-ion systems. Thiospinels represent an attractive choice for new Mg-ion cathode materials owing to their interconnected diffusion pathways and demonstrated high cation mobility in numerous systems. Reported magnesium thiospinels, however, contain redox inactive metals such as scandium or indium, or have low voltages, such as MgTi 2 S 4 . This article describes the direct synthesis and structural and electrochemical characterization of MgCr 2 S 4 , a new thiospinel containing the redox active metal chromium and discusses its physical properties and potential as a magnesium battery cathode. However, as chromium(III) is quite stable against oxidation in sulfides, removing magnesium from the material remains a significant challenge. Finally, early attempts at both chemical and electrochemical demagnesiation are discussed.

25 ENERGY STORAGE↗

Techno-Economic and Life Cycle Assessments for Sustainable Rare Earth Recovery from Coal Byproducts using Biosorption

Coal byproducts could be a promising feedstock to alleviate the supply risk of critical rare earth elements (REEs) due to their abundance and REE content. Herein, we investigated the economic and environmental potential of producing REEs from coal fly ash and lignite through an integrated process of leaching, biosorption, and oxalic precipitation on the basis of experimental data and modeling results. Two microbe immobilization systems (polyethylene glycol diacrylate (PEGDA) microbe beads and Si sol–gels) were examined for their efficiency in immobilizing Arthrobacter nicotianae to selectively recover REEs. Techno-economic analysis revealed that North Dakota lignite could be a profitable feedstock when Si sol–gel is used due to its high cell loading and REE adsorption capacity as well as high reuse cycles. Life cycle analysis revealed that Si sol–gel-based biosorption could be more environmental friendly than the prevailing REE production in China due to the use of less toxic chemicals. However, fly ash sourced from Powder River Basin coals was neither profitable nor environmentally sustainable, primarily due to low solubility of high-value scandium at an economical pulp density (100 g ash/L of acid solution). To further improve the proposed biotechnology, future research could focus on scandium recovery, leaching efficiency at a high pulp density, and reuse cycles of the immobilized microbes.

01 COAL, LIGNITE, AND PEAT↗

Temperature-mediated molecular ladder self-assembly employing Diels–Alder cycloaddition

Dynamic covalent self-assembly processes often exhibit poor capacities for error-correction owing to the relatively low connectivity rearrangement rates of dynamic covalent interactions and the common use of reaction conditions where the equilibrium state remains fixed. Here, we report a dynamic covalent self-assembly technique employing temperature, a conventional, externally-applied stimulus, to mediate the hybridization of peptoid oligomers bearing maleimide- and furan-based pendant groups to afford molecular ladders incorporating Diels–Alder adduct-based rungs. By raising or lowing the reaction temperature, this system enables the equilibrium state to be readily varied without altering reagent concentrations. Both triethylamine and the Lewis acidic scandium triflate were examined as candidate reaction catalysts; however, only scandium triflate increased the rate of single strand conversion. Additionally, as the Diels–Alder cycloaddition reaction does not liberate a small molecule, a registry-dependent mass change was effected by employing a base-catalyzed thiol-Michael addition reaction between any un-reacted maleimide pendant groups and a low molecular weight thiol to enable the number of Diels–Alder adduct rungs to be readily determined by mass spectrometry. Finally, by employing a slow temperature ramp from high to low temperature, approximating the thermal cycle employed for nucleic acid hybridization, sequence-selective hybridization between model, tetra-functional precursor strands was demonstrated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Bonding similarities and differences between Y–Sb–Te and Sc–Sb–Te phase-change memory materials

The scandium (Sc) – alloyed Sb 2 Te 3 phase-change alloy has recently been found to enable ultrafast crystal nucleation due to the formation of Sc-stabilized octahedral motifs in the amorphous phase, rendering cache-type phase-change memory feasible. When yttrium (Y) is added, however, non-octahedral bonding patterns form in the amorphous Sb 2 Te 3 -based network even though Y has a valence electron configuration similar to that of Sc and also forms perfect octahedral bonding environments with tellurium in the YTe crystal. Here we elucidate the origin of this difference between Sc and Y, by carrying out thorough ab initio simulations and orbital-based bonding analyses on amorphous Y–Sb–Te and Sc–Sb–Te compounds. We also demonstrate how the smooth overlap of atomic positions (SOAP) similarity kernel can be used to quantify the structural similarity of local motifs in the amorphous phase with respect to various crystalline yttrium and scandium tellurides, both in the nearest-neighbor shell and beyond. We discover that the bonding contrast of Y- and Sc-centered structural motifs in amorphous Sb 2 Te 3 stems from their parent crystals at high Te concentrations. The larger atomic radius of Y and the weaker charge transfer when bonded with Te is found to allow more Te neighbors and cause a more open bonding environment, leading to higher coordination numbers and non-octahedral environments. We discuss the implications of the different local environments for practical applications in memory devices.

36 MATERIALS SCIENCE↗

First-principles study of hydrogen- and oxygen-related complexes in ScN

Scandium nitride (ScN) is an attractive material for electronic applications due to its high n-type conductivity. Native defects and unintentional impurities may limit its electron concentration and reduce its mobility; therefore, it is important to control their formation and incorporation. Hydrogen and oxygen are unintentional impurities that are commonly present during growth and processing. They act as shallow donors in ScN and hence may be regarded as harmless or even favorable to achieving n-type conductivity. Here we show, using state-of-the-art first-principles calculations, that these impurities can be detrimental because they readily form complexes with scandium vacancies (V Sc ). Isolated V Sc have relatively high formation energies and thus have low concentrations and little impact on electronic properties. However, complexes between V Sc and either hydrogen or oxygen form more readily than the pristine vacancy and will act as both compensating and scattering centers. Our results point to the importance of controlling the incorporation of hydrogen and oxygen in ScN (and AlScN alloys) to avoid degradation of the electronic properties.

36 MATERIALS SCIENCE↗

Low-Temperature Plasma Treatment for Enhanced Recovery of Highly Valued Critical REEs from Coal (Final Report)

The principle objective of this project was to develop a novel process flowsheet using low-temperature plasma treatment (LTP) integrated with conventional hydrometallurgical processes to recover rare earth elements (REEs), especially highly valued REEs (i.e. scandium and critical REEs), from coal and coal byproducts. LTP treatment was used to pretreat the solid feed material prior to leaching in an effort to improve the leaching characteristics of the REEs and potentially reduce acid consumption. Initially, a detailed experimental program was performed on a laboratory LTP furnace to identify a set of process parameter values to be used for assessing the enhanced leaching performance achieved on four specific gravity fractions of West Kentucky No. 13 and Fire Clay coarse coal refuse materials. High-temperature oxidation (HTO)) was also evaluated as a means for improving REE leachability on the same fractions of both coal sources. The lixiviants used to assess leachability improvements included: i) untreated water, ii) 0.1 M ammonium sulfate solution and iii) 1.2 M sulfuric acid solution at a temperature of 75°C. The laboratory data was used to develop multiple process flow sheets using HTO only to produce a rare earth oxide mix concentrate or utilizing both LTP and HTO treatment processes to generate a high purity heavy REO mix concentrate and a light REO mix concentrate. A techno-economic analysis was performed on each circuit. Low-temperature plasma oxidation was found to enhance REE leaching characteristics for all specific gravity (SG) fractions of the West Kentucky No. 13 coarse refuse material. The leaching recovery improvement was preferentially achieved for the heavy REEs with higher values obtained when treating the lower density fraction material. For example, the leaching recovery for the heavy REEs in the untreated 1.6 SG Float fraction material was 8% in a 0.1 M ammonium sulfate solution. After LTP treatment for 32 hours, heavy REE recovery increased to 33%. The corresponding recovery value for the light REEs was 10%. These findings indicate a strong affinity of the heavy REEs with the organic material, which is the component being reduced in content during the LTP treatment. Scanning electron micrographs showed the development of a honeycomb structure with increased LTP treatment with higher surface area as confirmed from BET measurements. Higher surface area promotes improved leaching efficiency due to enhance chemical interactions. When using 1.2 M sulfuric acid, the LTP treatment was found to provide a heavy REE recovery increase from 23% to 53% for the 1.6 SG Float fraction which corresponded to an ash content increase from around 20% to 35%. However, LTP treatment provided no improvement in leaching characteristic for the 2.2 SG sink material in the acid solution, which was likely due to the low organic content. The LTP treatment of the Fire Clay SG fractions provided no improvement in REE leaching characteristic, which may be due to the association with REE minerals such as monazite and REE-associated mineral matter such as clays. High temperature oxidation using temperatures in the range of 600-750OC was found to significantly enhance the leaching characteristics of both the light and heavy REEs for all density fractions in both coarse coal refuse materials. Generally, the increase in light REE recovery for the West Kentucky material was from 15% for the untreated material to 90% for the HTO treated material at 600°C. Recovery values dropped significantly when using temperatures below 600°C and above 750°C. The impact of the excessive temperatures was most likely a result of sintering. For the heavy REEs, HTO significantly improved recovery in the lighter SG fractions, which may be due to an affinity with the organic content. Only limited heavy REE recovery improvement was obtained for the denser SG fractions. Another benefit of HTO is the conversion of calcium-based minerals to a very soluble calcium oxide, which is removable using a mild acid solution, and the conversion of Fe minerals to relatively insoluble minerals such as hematite and magnetite. The pregnant leaching solution produced from the leaching of all SG fractions obtained from both coal sources was treated using two stages of solvent extraction procedurally modeling a rougher-cleaner circuit followed by oxalic acid precipitation. Rare earth oxide products having a purity greater than 97% was produced from nearly all of the SG fractions. A novel process flowsheet was developed based on the selective leaching of heavy REEs that was made possible through LTP treatment of West Kentucky No. 13 coarse refuse followed by salt leaching. In the flowsheet, coal refuse material is ground to a top size of 1mm and then treated by LTP. The treated material is mixed into a 0.1 M ammonium sulfate solution and then filtered to produce a heavy REE enriched pregnant leach solution. The heavy REEs are concentrated by two stages of selective precipitation to produce a heavy REE mix oxalate and then roasted to obtain a heavy REO mix concentrate. The solid residues remaining after salt leaching is dried and then subjected to HTO treatment followed by concentration using selective precipitation and roasting to produce a light REO mix concentrate. An alternative circuit was developed using HTO treatment only to treat 100% of the coarse refuse material followed by selective precipitation and roasting to generate a high purity REO mix product. A techno-economic analysis performed for the treatment of West Kentucky No. 13 and Fire Clay coarse refuse based on a hypothetical 500-tph plant revealed that the net present value for all scenarios was significantly negative. Primary reasons include: i) a substantial decrease in the basket value of the final product relative to the feed and ii) high chemical costs relative to the amount of product generated. The basket value reduction was primarily due to little to no scandium recovery due to poor leaching characteristics when using low acid concentrations as necessitated by the low feed grades. Operating costs were primarily influenced by the chemical costs relative to the kilograms of concentrate produced and feed grade. For the Fire Clay coarse refuse material, the total operating cost was estimated to be $354 per kg of REO produced which was higher than the basket value of the REO product ($276/kg). Approximately 37% of the total cost was the sulfuric acid used during the leaching process. A comparative analysis performed to assess the economic viability of using low-temperature plasma furnaces found that market value enhancement for the generation of both heavy REO and light REO concentrates will be needed in addition to significant technology advancements to reduce the cost of plasma furnaces.

01 COAL, LIGNITE, AND PEAT↗

Unoccupied electronic resonances of Sc adsorbed on W(001) by k-resolved inverse photoemission

Scandium adsorbed on the (001) face of tungsten has been studied using Auger-electron spectroscopy, low-energy electron diffraction, k-resolved inverse photoelectron spectroscopy, work-function measurements, and relativistic-electronic-structure calculations. We find that the work function of W(001) does not decrease monotonically as a function of scandium adsorption but reaches a minimum value of Phi = 3.25 eV at 50% coverage. For a complete monolayer, an order 1 X 1 Sc overlayer is formed. Inverse photoemission in the isochromat mode was used to map the unoccupied energy levels of this overlayer along the bar-Gamma(bar-Mu) symmetry direction of the surface Brillouin zone. Local-density-functional calculations using the muffin-tin orbital method were performed for a 1 X 1 Sc overlayer on W and are compared with the experimental two-dimensional band structure.

Lamouri, A.↗

Phase stable rare earth garnets

A transparent ceramic according to one embodiment includes a rare earth garnet comprising A.sub.hB.sub.iC.sub.jO.sub.12, where h is 3.+-.10%, i is 2.+-.10%, and j is 3.+-.10%. A includes a rare earth element or a mixture of rare earth elements, B includes at least one of aluminum, gallium and scandium, and C includes at least one of aluminum, gallium and scandium, where A is at a dodecahedral site of the garnet, B is at an octahedral site of the garnet, and C is at a tetrahedral site of the garnet. In one embodiment, the rare earth garment has scintillation properties. A radiation detector in one embodiment includes a transparent ceramic as described above and a photo detector optically coupled to the rare earth garnet.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical/Optical Properties of Oliktok Aerosols Field Campaign Report

The arctic environment is changing at an alarming rate. During this time of escalation, it is important to understand the impacts of aerosols, both natural and anthropogenic. To support this effort, an aerosol sampling campaign was conducted at the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility third Mobile Facility (AMF3) at Oliktok Point on the North Slope of Alaska (NSA). The specific objectives of the campaign were to collect aerosol particles as a function of aerodynamic particle size in order to better understand the varying chemical and optical properties of the aerosols in the different particle size modes. A DRUM-style cascading impactor (Davis Rotating-Unit for Monitoring) was deployed at the beginning of March 2017 through the end of May 2017, collecting samples in eight size bins for each 12-hour period, thereby obtaining a diurnal signature. On March 6, a fire burned down the power generation shed at the sampling site. No samples were collected again until March 10. Due to DRUM sampler rotation issues, samples were collected intermittently until March 13. From March 14 through the end of the study, samples were collected with little interference. The size bins of the instrument range from approximately 10 to 0.09 μm; however, deployment at the Oliktok Point facility required an inlet configuration that effectively filtered out the coarsest size bin. Therefore, the reported size bins are 5.0 to 2.5, 2.5 to 1.15, 1.15 to 0.75, 0.75 to 0.56, 0.56 to 0.34, 0.34 to 0.26, and 0.26 to 0.09 μm. It is also possible that ultrafine particles were removed by electrostatic charging of the high-density polyethylene inlet tubing; however, confirmation of this would require further testing. The collected samples were returned to the University of California (UC), Davis for offline analysis. Particle mass concentrations were measured by soft-beta ray attenuation while optical attenuation was determined by broadband transmission spectrometry (10 wavelengths from 349 to 849 nm in 50 nm increments, minus 649 nm). The samples were then taken to the Advanced Light Source facility at Lawrence Berkeley National Laboratory for synchrotron-induced X-ray fluorescence spectrometry (SXRF). Thirty elements were detected, from sodium to molybdenum plus lead. The polarized nature of the synchrotron beam eliminates 97.5% of the primary Compton background, providing approximately a factor of 10 greater sensitivity than unpolarized X-ray instruments (Barberie et al. 2013). The data were reduced using custom software packages and analyzed for any sources of contamination, sample damage, or other potential causes of data invalidation. The interpretation of the final data set is ongoing and only early results will be described in this report. In spite of power and instrumental issues at the start, the field campaign was largely successful. Excluding the first stage that did not receive sample and power/rotational issues, the remaining stages were 99.7% complete (number of valid measurements/total number of measurements made). The percent of measurements below detection were < 30% for all species with the exception of sodium, magnesium, arsenic, and scandium. Sodium and magnesium were expected to be difficult to measure using SXRF due to low sensitivity at that energy range. Scandium is very rare in ambient samples unless near a very strong source. Arsenic is fairly common in urban settings but is not expected in the arctic environment.

54 ENVIRONMENTAL SCIENCES↗

Bixbyite- and anatase-type phases in the system Sc-Ta-O-N

The aim of our study was to modify the basis compound ss-TaON, which crystallizes in the monoclinic baddeleyite-type, by incorporation of appropriate dopant ions, in order to obtain anion-deficient cubic fluorite-type phases, which are of interest as solids with mobile nitrogen ions. For this purpose, scandium-doped tantalum oxide nitrides were prepared by ammonolysis of amorphous oxide precursors. An unexpected variety of phases with different structural features was observed: bixbyite-type phases of general composition Sc{sub x}Ta{sub 1-x}(O,N){sub y} with 0.33{<=}x{<=}1 and 1.7{<=}y{<=}1.9, yellow colored metastable anatase-type phases such as Sc{sub 0.1}Ta{sub 0.9}O{sub 1.2}N{sub 0.8} or Sc{sub 0.15}Ta{sub 0.85}O{sub 1.3}N{sub 0.7} and, additionally, anosovite-type phases Sc{sub x}Ta{sub 3-x}O{sub 2x}N{sub 5-2x} with 0{<=}x{<=}1.05. Selected phases were investigated by UV/vis spectroscopy. Anatase- and anosovite-type compounds show brilliant colors. In the anatase-type phase, a possible anion ordering was examined by theoretical methods. Additionally, energy calculations on phase stability were performed for Sc{sub x}Ta{sub 1-x}O{sub 1+2x}N{sub 1-2x} in the baddeleyite, rutile, and anatase structure types with varying amounts of dopants. - Graphical abstract: New anatase- and bixbyite-type phases obtained as single-phase samples in the system Sc-Ta-O-N.

36 MATERIALS SCIENCE↗

{sup 45}Sc Solid State NMR studies of the silicides ScTSi (T=Co, Ni, Cu, Ru, Rh, Pd, Ir, Pt)

The silicides ScTSi (T=Fe, Co, Ni, Cu, Ru, Rh, Pd, Ir, Pt) were synthesized by arc-melting and characterized by X-ray powder diffraction. The structures of ScCoSi, ScRuSi, ScPdSi, and ScIrSi were refined from single crystal diffractometer data. These silicides crystallize with the TiNiSi type, space group Pnma. No systematic influences of the {sup 45}Sc isotropic magnetic shift and nuclear electric quadrupolar coupling parameters on various structural distortion parameters calculated from the crystal structure data can be detected. {sup 45}Sc MAS-NMR data suggest systematic trends in the local electronic structure probed by the scandium atoms: both the electric field gradients and the isotropic magnetic shifts relative to a 0.2 M aqueous Sc(NO{sub 3}){sub 3} solution decrease with increasing valence electron concentration and within each T group the isotropic magnetic shift decreases monotonically with increasing atomic number. The {sup 45}Sc nuclear electric quadrupolar coupling constants are generally well reproduced by quantum mechanical electric field gradient calculations using the WIEN2k code. Highlights: Black-Right-Pointing-Pointer Arc-melting synthesis of silicides ScTSi. Black-Right-Pointing-Pointer Single crystal X-ray data of ScCoSi, ScRuSi, ScPdSi, and ScIrSi. Black-Right-Pointing-Pointer {sup 45}Sc solid state NMR of silicides ScTSi.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Infrared spectroscopy of Sc{sup +}(H{sub 2}O) and Sc{sup 2+}(H{sub 2}O) via argon complex predissociation: The charge dependence of cation hydration

Singly and doubly charged scandium-water ion-molecule complexes are produced in a supersonic molecular beam by laser vaporization. These ions are mass analyzed and size selected in a specially designed reflectron time-of-flight spectrometer. To probe their structure, vibrational spectroscopy is measured for these complexes in the O-H stretching region using infrared laser photodissociation and the method of rare gas atom predissociation, also known as ''tagging.'' The O-H stretches in these systems are shifted to lower frequency than those for the free water molecule, and the intensity of the symmetric stretch band is strongly enhanced relative to the asymmetric stretch. These effects are more prominent for the doubly charged ions. Partially resolved rotational structure for the Sc{sup +}(H{sub 2}O)Ar complex shows that the H-O-H bond angle is larger than it is in the free water molecule. Fragmentation and spectral patterns indicate that the coordination of the Sc{sup 2+} ion is filled with six ligands (one water and five argons).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Positive effect of Sc and Zr on globular microstructure formation in AA7075 thixoforming feedstock

One of methods of obtaining a fine globular microstructure in a semi-solid range, necessary for thixoforming process, is modifiers additions. For this purpose 0.5 weight percent of modifying elements-scandium and zirconium-was added to 7075 alloy. The microstructure of such alloy consisted of homogeneously distributed globular grains of solid solution with the following chemical composition: Mg - 1.9%, Al - 91.6%, Cu - 1.0%, Zn - 5.5%(all in wt.%). Quantitative metallographic analysis showed that the average grain size was 23.5 {mu}m, much smaller than in the alloy without additions and 3.08% volume fraction of precipitates in the form of a layer between spherical {alpha}(Al) grains. X-ray phase analysis of the 7075 alloy with Sc and Zr additions confirmed the dominant presence of aluminum solid solution and the intermetallic hexagonal phase MgZn{sub 2}. Electron diffraction pattern confirmed location of {eta}MgZn{sub 2} phase at the grain boundaries. EDS chemical analysis of the {eta}MgZn{sub 2} phase showed following content of elements: Mg - 17.2%, Al - 20.4%, Cu - 27.8%, Zn - 34.6%. The larger amount of Cu and Al indicated non-stoichiometry of the {eta} phase, which can be presented with a formula [Mg(Zn,Al,Cu){sub 2}]. Additionally, inside the aluminum solution, small, square-shaped precipitations enriched with Sc and Zr were observed. Electron diffraction pattern allowed identification of the precipitates as cubic Al{sub 3}(Sc,Zr) phase. The average hardness of feedstock was 105 HV5. DSC analysis during heating of the alloy enabled the estimation of a solidus line, at temperature of 548 deg. C and a liquidus line at temperature: 656 deg. C. For cooling, the temperatures for solidus and liquidus were 545 deg. C and 636 deg. C respectively. Additionally, the relation of liquid phase as a function of temperature was determined. Measurements of rheological properties in the semi-solid range, using the Searl system indicated that an increase of a particle size leads to an observable decrease of viscosity during isothermal shearing.

36 MATERIALS SCIENCE↗