Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Room temperature ionic conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Electrochemical performance of ionic polymer metal composite under tensile loading

Abstract Cracks in polymer composites can lead to premature failure, which can be disastrous for polymer-based energy storage devices. Detecting these cracks is essential to guarantee the reliability and safety of such devices. However, detecting cracks in composite polymers such as ionic polymer metal composites (IPMCs) is a challenging task, which makes it difficult to ensure their performance and safety. The overall goal of this study is to investigate the effect of cracks or damage caused by tensile loading on the mechanical properties and electrochemical characteristics of IPMC based capacitors. During tensile testing, the deformation of the IPMC strips causes changes in the ion distribution and concentration in the polymer matrix, influencing the performance of the material. The measurements were conducted utilizing electrochemical impedance spectroscopy at a room temperature ( 21 ∘ C ) and frequency range of 10 KHz to 1 Hz. The method utilized in this study proved to be easy and quick with consistent results. The IPMC capacitor was found to increase its capacitance after major cracking in the Pt electrodes from high tensile mechanical loads. Furthermore, at lower frequency range (<100 Hz), the real ( ε ′ ) and imaginary ( ε ′ ′ ) part of permittivity increase with the addition of loads. This displays that the dielectric property of the material is affected due to the increasing of the loads. It is concluded that, at frequencies above 100 Hz, the permittivity is weakly load dependent.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A room temperature rechargeable Li 2 O-based lithium-air battery enabled by a solid electrolyte

Lithium-air batteries have scope to compete with gasoline in terms of energy density. However, in most systems, the reaction pathways either involve one- or two-electron transfer, leading to lithium peroxide (Li 2 O 2 ) or lithium superoxide (LiO 2 ), respectively. Kondori et al. investigated a lithium-air battery that uses a ceramic-polyethylene oxide–based composite solid electrolyte and found that it can undergo a four-electron redox reaction through lithium oxide (Li 2 O) formation and decomposition (see the Perspective by Dong and Lu). The composite electrolyte embedded with Li 10 GeP 2 S 12 nanoparticles shows high ionic conductivity and stability and high cycle stability through a four-electron transfer process.

25 ENERGY STORAGE↗
DOE OSTI2024

Exploring the Nature of f-Element Soft Donor Interactions Using Electronically Tunable Azolate Ionic Liquids

This project was undertaken to advance the understanding of how f-elements interact with moderately soft donors, a heavily investigated yet open question which is of prime importance in spent nuclear fuel processing and fundamental inorganic chemistry. During the course of the project, based on exciting results, a stretch goal was developed to study the hydrolysis products of transuranic actinide metals, a somewhat understudied field even with its significance in nuclear fuel cycle and impacts in environmental chemistry. The stretch goal was to take our serendipitous discovery of an easy route to isolation of crystalline multinuclear ƒ-element hydrolysis products, and apply it to gaining a mechanistic understanding of Pu(III/IV) colloid formation. The simplicity of our techniques should lend themselves to the remote handling required for study of many transuranic elements. We developed several methodologies using azolium azolate chemistry to overcome ƒ-element hydrolysis problems that prohibit the isolation of ƒ-element soft donor complexes and to build a crystallographic library of ƒ-element N-donor complexes as a means to understand the fundamental differences between actinide and lanthanide interactions with moderately soft donor ligands. Our next major endeavor will be to transfer this chemistry from 4ƒ elements to transuranic elements, particularly in the study of hydrolysis of Pu(III/IV). While our work is fundamental in nature, applications of the knowledge we are generating should be felt in such diverse fields as catalysis, separations in general, nuclear waste remediation specifically, and many other applications in f-element magnetic and luminescent properties. The potential ramifications of the consistent and robust formation of hydrolysis controlled hexanuclear lanthanide structures are enormous, with future uses being catalyst formation, higher-nuclearity structure synthesis using our hexanuclear motif as a fundamental building block, Pu waste remediation, separations, and many other potential applications resulting from characteristic magnetic and luminescent properties of lanthanide polynuclear structures. Three synthetic methodologies (direct mixing with variable stoichiometries, use of volatile solvent, metathesis) were developed starting with 7 acidic and 6 basic azoles to obtain ionic liquids suitable for f-element coordination. Proton transfer by acidic/basic azole combination led to suitable low melting salts and two cocrystals. Acid/base reaction of azoles with soft-donor permanent cations of ([X 4444 ][OH] (where [X 4444 ] + = tetrabutylammonium [N 4444 ] + or tetrabutylphosphonium [P 4444 ] + ) with weakly acidic azoles including imidazole, 1,2,3-triazole, 1,2,4-triazole, 5-aminotetrazole, 4,5-dicyanoimidazole, and 2-amino-4,5-dicyanoimidazole) revealed several suitable low-melting salts. Metathesis reactions of Na(azolate) were conducted by first using weakly acidic azoles including 4,5-dicyanoimidazole, 2-amino-4,5-dicyanoimidazole, 5-aminotetrazole, and 1,2,4-triazole to form sodium or lithium salts using group(I) hydroxides in methanolic solutions. The best results were obtained by reacting the basic and acidic azoles directly in 1:1 or 3:1 ratios at elevated temperatures. Twenty-two azole mixtures were identified which are either low melting solids or room temperature liquids. Each of the low melting solids was confirmed to be a new solid phase, each of which is being further characterized. The liquids and solids are anticipated to be ILs, eutectics, or partially ionized systems, all of which will be suitable for the dissolution of f-element salts. Five new synthetic methodologies were developed to finding suitable crystallization conditions for f-element complexation with the goal of finding simple one pot reaction syntheses and crystallization strategies that could be used under the demanding conditions of transuranic chemistries. These synthetic methods yield many new crystalline phases which were studied by single crystal X-ray diffraction.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Composite Cathode Architectures Made By Freeze-Casting for All Solid State Lithium Batteries (CRADA Final Report)

As part of a Battery 500 seedling project, MBRDNA partnered with LBNL and Montana State University (MSU) to develop solid-state batteries based on an Al-substituted LLZO (Li 7 La 3 Zr 2 O 12 ) ceramic ion-conductor. All solid-state lithium batteries are attractive contenders for use as power sources for electric vehicles because of their potential for better safety and higher energy density than state-of-the-art lithium-ion batteries, although they are still at early stages of development. Al-substituted LLZO is one of the most promising solid electrolytes for battery applications based on high ionic conductivity, a wide operating voltage window, and apparent stability vs. reduction by lithium. However, difficulties with processing thin (< 20 $\textit{um}$ and dense LLZO membranes have hampered development of devices based on this material. It is non-compressible and must be sintered at high temperatures to densify components. It is also difficult to maintain contact between the active cathode material and LLZO in the composite cathodes, which is critical for successful operation. This research project aimed to use novel processing methods to overcome these issues. The end result was the first ever-reported truly all solid-state battery based on LLZO operating at room temperature without application of exogenous pressure. During the course of the project, we also identified a number of issues that need to be addressed to improve the technology readiness level of this battery.

25 ENERGY STORAGE↗
DOE OSTI2021

Polymer-ceramic composite electrolytes for all-solid-state lithium batteries: Ionic conductivity and chemical interaction enhanced by oxygen vacancy in ceramic nanofibers

Perovskite Li 3x La 2/3-x TiO3 (LLTO) nanofibers have been heat-treated in the hydrogen-containing atmosphere and then incorporated with the poly(vinylidene fluoride)-co-hexafluoropropylene (PVDF-HFP) polymer to form a composite electrolyte. Hydrogen treatment has created oxygen vacancies in the LLTO nanofibers, which has reduced the activation energy of Li ion transport along intra-grains and inter-grains, leading to improvement in the ion conductivity of LLTO nanofibers. Hydrogen treatment of the LLTO nanofibers has also enhanced the chemical interaction between the LLTO nanofibers and the polymer matrix in the composite electrolyte, and favored the Li ion transport at the nanofiber/polymer interface, improving the ion conductivity of the composite electrolyte to 3.4×10- 4 S/cm at room temperature. As a result, the Li|composite-electrolyte|Li half-cell exhibits good stability during lithium plating/stripping cycling at room temperature, showing an overpotential of ~91 mV at a constant current density of 0.5 mA/cm 2 . Finally, the full-cell battery with the composite electrolyte, lithium metal anode and lithium iron phosphate cathode shows excellent rate capacity and cycling performance.

25 ENERGY STORAGE↗
DOE OSTI2025

Atomistic Mechanisms of the Crystallographic Orientation‐Dependent Cu 1.8 S Conductive Channel Formation in Cu 2 S‐Based Memristors

Achieving multiple types of resistive switching in a single material with controlled ionic motion is a key challenge in neuromorphic computing, traditionally addressed by combining materials with distinct switching behaviors. Here, Cu 2-x S is identified as a promising candidate to overcome this limitation due to its hierarchical phase transitions. Using in situ biasing experiments, reversible and non-reversible phase transitions (and resistive switching) are demonstrated in γ-Cu 2 S by controlling the compliance current. The formation of parallel high-digenite Cu 1.8 S channels, orientated along the γ-Cu 2 S [201] crystallographic direction, drives the nonvolatile resistive switching. These channels emerge via an intermediate δ-Cu 2 S phase and are stabilized at room temperature by residual strains, alongside β-Cu 2 S phase. In conclusion, the work clarifies the complex, electrically triggered phase transformations in γ-Cu 2 S, and highlights the potential of Cu 2-x S as a versatile material for neuromorphic computing.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

High areal capacity, long cycle life 4 V ceramic all-solid-state Li-ion batteries enabled by chloride solid electrolytes

All-solid-state Li batteries (ASSBs) employing inorganic solid electrolytes offer improved safety and are exciting candidates for next-generation energy storage. Herein, we report a family of lithium mixed-metal chlorospinels, Li 2 In x Sc 0.666-x Cl 4 (0 ≤ x ≤ 0.666), with high ionic conductivity (up to 2.0 mS cm -1 ) owing to a highly disordered Li-ion distribution, and low electronic conductivity (4.7 × 10-10 S cm -1 ), which are implemented for high-performance ASSBs. Owing to the excellent interfacial stability of the SE against uncoated high-voltage cathode materials, ASSBs utilizing LiCoO 2 or LiNi 0.85 Co 0.1 Mn 0.05 O 2 exhibit superior rate capability and long-term cycling (up to 4.8 V versus Li+/Li) compared to state-of-the-art ASSBs. In particular, the ASSB with LiNi 0.85 Co 0.1 Mn 0.05 O 2 exhibits a long life of >3,000 cycles with 80% capacity retention at room temperature. Additionally, high cathode loadings are also demonstrated in ASSBs with stable capacity retention of >4 mAh cm -2 (~190 mAh g -1 ).

25 ENERGY STORAGE↗
DOE OSTI2020

Semiconducting High-Entropy Chalcogenide Alloys with Ambi-ionic Entropy Stabilization and Ambipolar Doping

Entropy stabilization is a novel materials-design paradigm to realize new compounds with widely tunable properties. However, almost all entropy-stabilized materials so far are either conducting metals or insulating ceramics, with a clear dearth in the semiconducting regime. Here, a new class of the multi-cationic and -anionic entropy-stabilized chalcogenide alloys based on the (Ge,Sn,Pb)(S,Se,Te) formula are synthesized and characterized experimentally. The con-figurational entropy from the disorder of both the anion and the cation sublattices reaches a record value of ~2.2 R mol -1 for the equimolar composition and stabilizes the single-phase solid solution. Theoretical calculations and experiments both show that the synthesized alloys are thermodynamically stable at the growth temperature and kinetically metastable at room temperature, segregating by spinodal decomposition at moderate temperatures. In conclusion, doping and electronic transport measurements verify that the synthesized materials are ambipolarly dopable semiconductors, which paves the way for the wider adoption of entropy-stabilized chalcogenide alloys in functional applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synthesis of Fluorine-Doped Lithium Argyrodite Solid Electrolytes for Solid-State Lithium Metal Batteries

Solid-state lithium metal batteries (SSLMBs) that utilize novel solid electrolytes (SEs) have garnered much attention because of their potential to yield safe and high-energy-density batteries. Sulfide-based argyrodite-class SEs are an attractive option because of their impressive ionic conductivity. Recent studies have shown that LiF at the interface between Li and SE enhances electrochemical stability. However, the synthesis of F-doped argyrodites has remained challenging because of the high temperatures used in the state-of-the-art solid-state synthesis methods. In this work, for the f irst time, we report F-doped Li 5+y PS 5 F y argyrodites with a tunable doping content and dual dopants (F-/Cl- and F-/Br-) that were synthesized through a solvent-based approach. Among all compositions, Li 6 PS 5 F 0.5 C l0.5 exhibits the highest Li-ion conductivity of 3.5 x 10 -4 S cm -1 at room temperature (RT). Furthermore, Li symmetric cells using Li 6 PS 5 F 0.5 Cl 0.5 show the best cycling performance among the tested cells. X-ray photoelectron spectroscopy and ab initio molecular dynamics simulations revealed that the enhanced interfacial stability of Li 6 PS 5 F 0.5 C l0.5 SE against Li metal can be attributed to the formation of a stable solid electrolyte interphase (SEI)-containing conductive species (Li 3 P), alongside LiCl and LiF. These findings open new opportunities to develop high-performance SSLMBs using a novel class of F-doped argyrodite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2022

Highly Loaded Sulfur Cathode, Coated Separator and Gel Electrolyte for High Rate Li-Sulfur Batteries

As one of DOE Battery 500 Seedling projects, Cornell University and EIC Labs investigated and developed i) highly loaded sulfur cathodes (> 3 mg/cm 2 ), ii) hybrid separators, and iii) gel ceramic electrolytes (GCE) to mitigate the low rate capability, shuttling effect and limited cycle life in high performance Li-Sulfur batteries. Scalable nanomanufacturing processes such as air-controlled electrospray (ACES) and gas-assisted electrospinning (GAES) have been utilized to develop directly deposited electrodes and polymer/ceramic hybrid separators. First, in the development of highly loaded cathodes, alternating layers of sulfur impregnated mesoporous carbon and graphene were fabricated via ACES and the resulting layered cathodes and coated separators exhibit higher capacity and capacity retention (about 1,000 mAh/g capacity with less than 0.02% fade/cycles) than single layer cathode or cathode prepared by conventional slurry cast. Alternating layer approach via ACES has been applied to high loading systems (3 - 5 mg S/cm 2 ), demonstrating the potential to increase sulfur utilization and capacity retention. We have also incorporated iron oxides (Fe 3 O 4 ) into S/mesoporous carbon/graphene cathodes to enhance sulfur utilization and mitigation of polysulfide shuttling. and the effect of Fe 3 O 4 in mesoporous carbon and Gr is highly pronounced at high C rates of 1C and 2C cycling performance. To further improve the cathodes at high rates, graphene nanoribbons (GNR) which can promote ion transport were incorporated in the cathode, resulting in 550 mAh/g at 5C/5C rates. Hybrid Li-ion/Li-S cathodes has also been explored to better engage unreacted polysulfides during charge/discharge. S/LFP hybrid cathodes offer higher sulfur utilization and enhanced rate capability, as well as higher areal loading. This study suggests inclusion of iron phosphide (Fe2P) which can chemically interact with polysulfides can further enhance sulfur utilization and mitigation of soluble polysulfides at high rates. Secondly, in the development of hybrid separators, we first employed graphene coating on the commercial polyolefin separators, which exhibits higher capability, better capacity retention and enhanced rate capability. To improve the rate capability with enhanced safety features such as thermal stability and nonflammability, we developed polymer/ceramic hybrids based on thermally stable polyimide (PI) and room temperature curable ceramic precursors such as organopolysilazane (OPSZ) or polysilsesquioxanes (PSSQ), which exhibit no shrinkages up to 300 ºC and non-flammability. To improve mechanical properties and electrochemical stability, polybenzimidazole (PBI) and alumina have been incorporated in polymer/ceramic hybrid separator, replacing PI and OPSZ/PSSQ, respectively. Finally, the gel ceramic electrolyte (GCE) based on ceramic cross linkers have been applied to make Li-S cells even safer and also to mitigate the polysulfide shuttling further. The resulting gel ceramic electrolyte offers improved capacity retention and rate capability, and also effectively mitigates polysulfide shuttling which was also confirmed by modeling. Inclusion of high ion conducting additives into GCE together with polymer/ceramic hybrid separators exhibit the higher ionic conductivity than liquid electrolyte with commercial polyolefin separator. We demonstrated that the developed highly loaded sulfur cathodes, polymer/ceramic hybrid separators and gel ceramic electrolyte can effectively mitigate the low rate capability, shuttling effect and limited cycle life in high performance Li-Sulfur batteries with improved safety.

25 ENERGY STORAGE↗
DOE OSTI2021

Proton switching molecular magnetoelectricity

Abstract The convergence of proton conduction and multiferroics is generating a compelling opportunity to achieve strong magnetoelectric coupling and magneto-ionics, offering a versatile platform to realize molecular magnetoelectrics. Here we describe machine learning coupled with additive manufacturing to accelerate the design strategy for hydrogen-bonded multiferroic macromolecules accompanied by strong proton dependence of magnetic properties. The proton switching magnetoelectricity occurs in three-dimensional molecular heterogeneous solids. It consists of a molecular magnet network as proton reservoir to modulate ferroelectric polarization, while molecular ferroelectrics charging proton transfer to reversibly manipulate magnetism. The magnetoelectric coupling induces a reversible 29% magnetization control at ferroelectric phase transition with a broad thermal hysteresis width of 160 K (192 K to 352 K), while a room-temperature reversible magnetic modulation is realized at a low electric field stimulus of 1 kV cm −1 . The findings of electrostatic proton transfer provide a pathway of proton mediated magnetization control in hierarchical molecular multiferroics.

36 MATERIALS SCIENCE↗
NASA NTRS2017

Aerogels: Overview and Outlook for Future Space and Terrestrial Applications at NASA

Aerogels are a class of porous solids which exhibit many extreme properties originating from a nanoporous skeletal architecture. One class of aerogel, polyimide-based, possesses low dielectric constants, low thermal conductivities, high porosity, flexibility and low densities with outstanding mechanical properties. Due to their wide array of interesting and useful material properties, they are being employed in many new applications as an enabling technology. In this presentation, I will be giving an overview into the history, properties, and synthesis of aerogels along with a few successful projects at NASA involving the synthesis of novel aerogel formulations.

Nanoporous↗
DOE OSTI2021

Computational study of Li 3 BO 3 and Li 3 BN 2 II: Stability analysis of pure phases and of model interfaces with Li anodes

Both Li 3 BO 3 and Li 3 BN 2 materials have promising properties for use in all solid-state batteries and other technologies dependent on electrolytes with significant ionic conductivity. As the second of a two-part study, the structural properties of Li 3 BO 3 and three reported phases of Li 3 BN 2 are investigated using first-principles modeling techniques. For alpha- Li 3 BN 2 , the tetragonal P4 2 / mnm structure reported in the literature is found to be unstable as evidenced by imaginary phonon modes near the M point of its Brillouin zone. Our simulations within the harmonic approximation suggest that the real α phase has the orthorhombic space group symmetry Pmmn formed with twice as many formula units and tiny adjustments of the equivalent lattice parameters and fractional coordinates. Extending the analysis of the Pmmn α- Li 3 BN 2 structure to the quasiharmonic approximation improves the agreement between the room-temperature x-ray pattern reported in the literature and the corresponding simulation results. In anticipation of the use of the monoclinic phases of Li 3 BO 3 and Li 3 BN 2 in Li ion conducting applications, chemical stability is investigated in terms of free-energy differences of possible decomposition and Li reaction processes, finding encouraging results. As further investigations of Li 3 BO 3 and β- Li 3 BN 2 as electrolyte or coating materials, particularly for use with Li metal anodes, idealized electrolyte/Li interfaces were investigated in terms of their geometric, energetic, and electronic properties. The results find the electrolyte/Li interfaces to be quite favorable, perhaps comparable to the pioneering LiPON/Li system.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Low-Temperature Structural Transition in Canfieldite, Ag 8 SnS 6 , Single Crystals

Canfieldite, Ag 8 SnS 6 , is a semiconducting mineral notable for its high ionic conductivity, photosensitivity, and low thermal conductivity. In this paper, we report the solution growth of large single crystals of Ag 8 SnS 6 of mass up to 1 g from a ternary Ag–Sn–S melt. On cooling from high temperature, Ag 8 SnS 6 undergoes a known cubic ($F\bar{4}3m$) to orthorhombic ($Pna2_1$) phase transition at ≈460 K. By studying the magnetization and thermal expansion between 5–300 K, we discover a second structural transition at ≈120 K. Single crystal X-ray diffraction reveals the low-temperature phase adopts a different orthorhombic structure with space group $Pmn2_1$ ($\textit{a}$ = 7.662 9(5) Å, $\textit{b}$ = 7.539 6(5) Å, $\textit{c}$ = 10.630 0(5) Å, Z = 2 at 90 K) that is isostructural to the room-temperature forms of the related Se-based compounds Ag 8 SnSe 6 and Ag 8 GeSe 6 . The 120 K transition is first-order and has a large thermal hysteresis. On the basis of the magnetization and thermal expansion data, the room-temperature polymorph can be kinetically arrested into a metastable state by rapidly cooling to temperatures below 40 K. We last compare the room- and low-temperature forms of Ag8SnS6 with its argyrodite analogues, Ag 8 TQ 6 ($\textit{T}$ = Si, Ge, Sn; $\textit{Q}$ = S, Se), and identify a trend relating the preferred structures to the unit cell volume, suggesting smaller phase volume favors the $Pna2_1$ arrangement. We support this picture by showing that the transition to the $Pmn2_1$ phase is avoided in Ge alloyed Ag 8 Sn 1–x Ge x S 6 samples as well as in pure Ag 8 GeS 6 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Facile Room-Temperature Electrodeposition of Rare Earth Metals in a Fluorine-Free Task-Specific Electrolyte

Electrochemical deposition of rare earth metals at room temperature has attracted increasing interest due to its advantage in energy efficiency over traditional hydrometallurgical and pyrometallurgical processes. Recent progress has been made with fluorinated electrolyte systems; however, the formation of an electrode-passivating fluoride layer by electrolyte decomposition is often overlooked. Such a passivation layer causes significant and rapid decay of the deposition current and significantly hinders practical application. To address this issue, we demonstrate a fluorine (F)-free task-specific electrolyte utilizing the borohydride anion for the efficient electrodeposition of rare earth metals. By eliminating the passivation effect, the deposition process exhibits a stable current and accumulates a thick neodymium deposit on the electrode. Raman spectroscopy of the electrolyte reveals a synergetic effect between rare earth borohydride and lithium borohydride which promotes the dissociation of both borohydride salts, resulting in significantly increased ionic conductivity and electrochemical performance. Cyclic voltammetry and in-depth X-ray photoelectron spectroscopy of the deposits suggest that the electrodeposition of rare earth metals could undergo a Li-mediated reduction process. Finally, quantitative analysis of the deposits reveals that the overall concentration of the rare earth elements reaches 75% which contains 40–48% metallic phase.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Interconnected cathode-electrolyte double-layer enabling continuous Li-ion conduction throughout solid-state Li-S battery

All-solid-state lithium (Li) batteries with high energy density are a promising solution for the next-generation energy storage systems in large-scale devices. To simultaneously overcome the challenges of poor ionic conduction of solid electrolytes and shuttling of active materials, here we introduce a functional electrolyte-cathode bilayer framework with interconnected LLAZO channels from the electrolyte into the cathode for advanced solid-state Li-S batteries. Differing from the traditional solid-state batteries with separated layer compositions, the introduced bilayer framework provides ultrafast and continuous ion/electron conduction. Instead of transferring Li+ across the polymer and garnet phases which involve huge interfacial resistance, Li+ is directly conducted through the LLAZO channels created continuously from the cathode layer to the solid electrolyte layer, significantly shortening the diffusion distance and facilitating the redox reaction of sulfur and sulfides. A stable cycle life is demonstrated in the prototype Li-S solid-state batteries assembled with the introduced LLAZO-LLAZO@CNF interconnected bilayer framework. High capacity is obtained at room temperature, indicating the superior electrochemical properties of the bilayer framework that result from the unique design of the interconnected LLAZO garnet phase.

25 ENERGY STORAGE↗
DOE OSTI2022

Impact of modifier-rich coatings on the ionic transport of glasses [Poster]

Ionic conduction in silicate glasses is mainly influenced by the nature, concentration, and mobility of the network-modifying (NWM) cations. The electrical conduction in SLS is dominated by the ionic migration of sodium moving from the anode to the cathode. An activation energy for this conduction process was calculated to be 0.82eV and in good agreement with values previously reported. The conduction process associated to the leakage current and relaxation peak in TSDC for HPFS is attributed to conduction between nonbridging oxygen hole centers (NBOHC). It is suggested that ≡Si-OH = ≡Si-O - + H 0 under thermo-electric poling, promoting hole or proton injection from the anode and responsible for the 1.5eV relaxation peak. No previous TSDC data have been found to corroborate this mechanism. The higher activation energy and lower current intensity for the coated HPFS might be attributed to a lower concentration of NBOHC after heat treatment (Si-OH + OH-Si = SiO-Si + H 2 O). This could explain the TSDC signal around room temperature for the coated HPFS. Another possible explanation could be a redox reaction at the anode region dominating the current response.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Study on the Synthesis and Proton Transport Behavior of Multilayered ZSM-5 Zeolite Nanosheet Membranes Laminated on Polymer Substrates

Single crystalline ZSM-5 ZNs with thicknesses around 6 nm were obtained by secondary growth of silicalite nanoparticles using diquaternary bis-1,5(tripropyl ammonium) pentamethylene diiodide (dC5) as a structure-directing agent (SDA). The dC5 could be effectively removed from the ZN pores by either high-temperature calcination or UV irradiation in air at room temperature but not by the piranha solution treatment. Ultrathin ZN-laminated membranes (ZNLMs) were fabricated by sandwiching a UV-activated multilayered ZN film between two recast Nafion® layers (ZNLM-Nafion) and by filtration coating from a suspension of thermally activated ZNs on a nonionic porous PVDF (ZNLM-PVDF). The ZNLMs on both supports demonstrated the ability of highly proton-selective ion conduction with low resistances in aqueous electrolyte solutions. The ZNLM-PVDF with PVDF binder was structurally stable, and it achieved a comparably low ASR but much higher proton selectivity compared with a Nafion membrane of same overall thickness. However, detachment between the ZNLM and Nafion layers occurred when the ZNLM-Nafion operated in aqueous electrolyte solutions. Results of this study show the potential for developing ZNLMs as efficient proton-conducting membranes without using expensive ionic polymer matrices. However, the development of polymer-supported ZNLMs is hindered by the current inefficiency in preparing well-dispersed suspensions of open-pore ZNs. Future development of efficient methods for synthesizing open-pore ZNs in dispersed states is key to realizing high-performance ZNLMs on polymers.

36 MATERIALS SCIENCE↗