Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rep”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

160 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1942

Comparison of Aileron Control Characteristics as Determined in Flight Tests of P-36, P-40, Spitfire, and Hurricane Pursuit Airplanes

The Army Air Force has made available several pursuit-type airplanes for quantitative investigation of their flying and handling qualities. One Item of special interest obtained from the results of the investigation is a comparison of the aileron control characteristics of the P-36, P-40, Hawker Hurricane, and Supermarine Spitfire airplanes. Figure 1 shows the design characteristics of the ailerons and the control sticks of the four airplanes. Aileron effectiveness may be expressed in terms of the helix angle generated by the wing tip in a steady roll. This angle is given by the expression pb/2V, where p is the rolling velocity, b the wing span, and V the true airspeed, expressed in consistent units. This quantity is convenient to use because, although it does not rep resent directly the rolling velocity of airplanes of different spans or airplanes operating at different speeds, it provides a satisfactory basis for computing the rate of roll and the time required to bank a given amount under any given set of conditions. The ratio of pb/2V obtained in any roll to the maximum value reached with full aileron deflection indicates the fraction of the maximum aileron travel that was reached. A complete discussion of this criterion for aileron effectiveness is given in reference 1. The aileron effectiveness of the various airplanes is compared in the following table on the basis of the response obtained with stick forces of 30 and 5 pounds. A force of 30 pounds is somewhat less than the greatest stick force exerted by the pilot. Repeated flight measurements have shown, however, that this force is a reasonable upper limit for maneuvering at high speeds.

Phillips, William H.↗
NASA NTRS2017

Oriented Mineral Transformation in a Dark Inclusion from the Leoville Meteorite

Dark inclusions (DIs) in chondrites and achondrites are dark gray to black fragments that include a wide variety of materials that have experienced very different petrologic histories. Based on the law of inclusions, they are rocks that accreted prior to and are older than their host meteorites and possibly rep-resent an earlier generation of material. The origin of these inclusions and their relationship to their host meteorites is not always clear. They are interesting in that they represent lithologies that experienced different parent body histories than their host meteorites and are either exotic components or originated from different regions of the meteorite parent body. In many cases, DIs in CV chondrites have been altered to greater degrees than their host meteorites suggesting pre accretionary alteration [e.g., 1,2,3]. There is debate concerning whether or not these DIs record an earlier era of aqueous alteration and subsequent thermal metamorphism, and how these processes may have also affected the host CV materials. The present study is a description of a dark inclusion found in the Leoville meteorite (specifically, thin section USNM 3535-1). This inclusion has some interesting features that have considerable relevance for this discussion.

Buchanan, P. C.↗
NASA NTRS2017

Diffusivities of Redox-Sensitive Elements in Basalt vs. Oxygen Fugacity Determined by LA-ICP-MS

Several diffusion experiments were conducted in a piston cylinder device across a range of oxygen fugacities (FMQ-3 FMQ-1.2, FMQ+6) at 1 GPa and 1300 C. This was done to explore the effects of oxygen fugacity (fO2) on diffusivity of redox sensitive trace elements. This allows investigation of how these elements diffuse across the fO2 range encountered in different reservoirs on planets and moons in our solar system. The University of Rochester LA-ICP-MS system was used for analysis of samples. Analyses were conducted using an Agilent 7900 quadrupole mass spectrometer connected to a Photon Machines 193 nm G2 laser ablation (LA) system equipped with a HelEx 2-volume sample chamber. Spots used were 35 micrometers circles spaced at 65 micrometers intervals. Laser fluence was 7.81 J/cm^2 with a rep rate of 10 Hz. The iolite software package was used to reduce data collected from laser ablation analysis of experiments with Si-29 used as the internal standard isotope. Iolite's global fit module was used to simultaneously fit elements' diffusivities in each experiment while keeping the Matano interface constant. Elements analysed include V, Nb, W, Mo, La, Ce, Pr, Sm, Eu, Gd, Ta, and W. Figures

Szumila, Ian↗
NASA NTRS2017

Effects of Martian Surface Materials on the Thermal Decomposition of Hydrogen Peroxide

While hydrogen peroxide (H2O2) has been detected in the martian atmosphere, it has not been detected in surface materials. Since the Viking lander mission, we have sent instruments to Mars with the capability to detect H2O2. The Sample Analysis at Mars (SAM) instrument onboard the Curiosity Rover and Thermal and Evolved Gas Analyzer (TEGA) instrument on the Phoenix lander both detected water and oxygen releases from analyzed sediments but whether or not peroxide could be the source of these gases has not been investigated. We are investigating the possible presence of H2O2 in martian materials by analyzing Mars-relevant minerals that have been mixed with hydrogen peroxide using lab instruments configured as analogs to Mars mission instruments. The object of this research is to use lab instruments to find the effects of Mars analog minerals on hydrogen peroxide gas release temperatures, specifically gas releases of water and oxygen and also determine the effect of the peroxide on the minerals. Data that we get from the lab can then be compared to the data collected from Mars. The minerals hematite, siderite, San Carlos olivine, magnetite and nontronite were chosen as our Mars analog minerals. ~20 mg of analog Mars minerals with 5μl of 50% H2O2, and were either run immediately or placed in a sealed tube for 2, 4, or 9 days to look for changes over time with two reps being done at each time step to determine repeatability. Each sample was heated from -60 degC to 500 degC at 20 degC/min and the evolved gases were monitored with a mass spectrometer. Each sample was also analyzed with an X-ray diffraction instrument to look for changes in mineralogy. Preliminary results show three potential outcomes: 1) peroxide has no effect on the sample (e.g., hematite), 2) the mineral is unaffected but catalyzes peroxide decomposition (magnetite, siderite), or 3) peroxide alters the mineral (pyrrhotite, San Carlos olivine).

Archer, P. D., Jr.↗
NASA NTRSDate not supplied

Thermodynamic and Diffusion Model Estimates on Metamorphic Temperatures and Timescales for Basaltic Eucrite GRA 98098

Introduction: HED meteorites are thought to rep-resent igneous rocks from Vesta’s basaltic crust and preserve evidence of early crustal metamorphism. Determining the temperatures and timescales of thermal metamorphism is important for reconstructing crustal evolution in the early solar system. Here, we study basaltic eucrite Graves Nunataks (GRA) 98098, which has been identified as a highly metamorphosed eucrite [1]. We present new estimates on metamorphic temperatures determined via thermodynamic modeling as well as the initial results from diffusion models constraining timescales of thermal metamorphism. Sample Description: GRA 98098 is an unbrecciated eucrite with a granoblastic plagioclase and pyroxene mineralogy. Millimeter to cm-long lathes of tridymite cross-cut and poikilitically enclose plagioclase and pyroxene [1,this work]. Pyroxene grains have exsolved into Ca-rich (~Wo38En29Fs33) and Ca-poor (~Wo4.5En36Fs59.5) lamellae. Both unzoned and zoned plagioclase grains are observed. Unzoned plagioclase grains are found solely with tridymite laths. These grains have ~An92 compositions. The cores of the zoned plagioclase grains have the same composition and thin, relatively sodic rims (~An67), (Fig. 1). The bulk sample is unusually enriched in highly in-compatible elements and has one of the most fractionated REE patterns reported [1]. Maximum metamorphic temperatures of 985±78°C have been estimated using two-pyroxene thermometry [2]. Methods: Thermodynamic modeling. Thermodynamic models were constructed using the software Perple_X, which employs a Gibbs free energy minimization in order to determine the most stable phase assemblage for a given bulk rock composition [3]. Bulk composition was calculated using mineral com-positions acquired via EMPA (this study) and the observed abundancies present in the thin section. Two bulk compositions were estimated; 1) includes all phases present in the thin section, (assumes that all phases are present during metamorphism), 2) excludes tridymite from the bulk calculation (assumes that tridymite was not present during metamorphism). In order to determine whether metamorphic equilibria was achieved and estimate temperatures of metamorphism, we compared measured pyroxene compositions with thermodynamically predicted compositions [4, Fig. 2]. Diffusion Modeling. Several time-temperature de-pendent diffusion profiles were calculated in order to determine the best match for XAn chemical profiles observed at the edges of the zoned plagioclase (Fig. 3). We assumed that the start condition was a stepwise gradient at the plagioclase/pyroxene interface. We also assumed an average diffusion coefficient (D) and a constant temperature using the equation in [5]. D was determined for two temperatures (T = 1060ºC; near eucrite solidus [6] and T = 985ºC; metamorphism reported in [4]) and then XAn was calculated as a function of distance from plagioclase core to rim using an error function solution to Fick’s second law. Results: Thermodynamic model results are summarized in Fig. 2. For a bulk composition that includes all phases in the thin section, pyroxene endmember compositions plot in the following temperature ranges: Fs ~660-860ºC, En~1000ºC & 1150ºC, and Wo~760-900ºC (Fig. 2a). For a bulk composition that excludes tridymite from the peak metamorphic assemblage (i.e., the bulk composition minus the contribution from tridymite), a temperature range could not be determined for the Fs component of pyroxene. For Wo, T~760-900ºC and En, T~1000ºC & 1150ºC (Fig. 2b). Fig. 3 summarizes the diffusion model results. For T = 1060°C & 985°C, the most appropriate time interval was estimated based on which diffusion curve most matched (solid lines, Fig. 3) the EMPA data. For T = 1060°C, the best looking match was t = 500 ka. For T = 985°C, the best match was t = 7 Ma. Discussion and future work: Temperature estimates from thermodynamic models are not conclusive because the temperature ranges determined for pyroxene endmember stability do not overlap (colored fields in Fig. 2), thus implying that there is disequilibrium between pyroxene crystals and the bulk composition considered [4]. Thus, additional exploration is needed to define a metamorphically equilibrated do-main that accurately records peak temperature. The utility of defining metamorphically equilibrated do-mains to improve the accuracy and level of detail elucidated regarding the petrogenetic history of metamorphose samples has been demonstrated previously [4,7]. We suggest that in the case of Fig. 2a, the thin section composition is not representative of the length scales over which metamorphic equilibrium was achieve and in the case of Fig. 2b, the assumption that tridymite was not present during metamorphism was incorrect. However, results from thermodynamic models can provide insight into the relative timing of mineral and compositional textures. For example from texture alone, it is unclear whether tridymite was igneous in origin and represents the last bits of melt in a crystallizing magma chamber, or if it formed during (and possibly initiated) open system thermal metamorphism. The latter could be consistent with a partial melt hypothesis [8,9] while the former implies that simple fractional crystallization can yield the textures present in GRA 98098. The lack of coincidence be-tween pyroxene endmember compositions in Fig. 2b suggest that the bulk composition minus tridymite was not the assemblage in equilibrium with the pyroxene, suggesting that tridymite was present during metamorphism and formed during igneous crystallization. We conclude that the development of the Na-rich plagioclase rims likely occurred during or immediately after peak thermal metamorphism, because eucrites of similar metamorphic grade and texture have unzoned plagioclase (~An92) [2,4,8], and Na zoning is only observed in the plagioclase not included in the tridymite. This suggests that the zoning formed after tridymite formation, and therefore after igneous crystallization. Thus, the timescales calculated via diffusion modeling possibly represent the time interval over which thermal metamorphism occurred. Cooling rates approximated for the Vestan crust predict that the crust cooled below 300°C around 35-40 Ma after formation[10]. This is consistent with our modeling results that predict formation of the Na rich plagioclase rims occurring at higher temperatures over a period of 0.5 to 7 Ma years. Future work. Additional thermodynamic modeling work will focus on selecting an equilibrated bulk rock domain in which to elucidate metamorphic conditions. Diffusion models currently provide a minimum time-scale, since diffusion slows down as the system cools. Future work with will focus on integrating cooling into the diffusion models and constraining the depth at which thermal metamorphism occurs because it could be used to determine whether the range of time-scales calculated for thermal metamorphism are consistent with the geologic environment.

J S Gorce↗
NASA NTRSDate not supplied

Enumeration and Fluorescence In Situ Hybridization of Microbial Bioburden on Cleanroom Surfaces

Introduction: Microorganisms are everywhere on Earth, even in the cleanest of places. Spacecraft assembly cleanrooms can harbor low levels of living and dead microbial cells (e.g., [1,2]), and cleanroom bioburden can also include organic molecules from industrial sources and in situ biomass. Life detection missions require careful attention to avoid contaminants that can be easily convoluted with analytical targets. We are evaluating epifluorescent microscopy and fluorescence in situ hybridization (FISH) as methods to complement organic contamination detection techniques. Epifluorescent cell counting offers an accurate and cost-effective way to quantify low levels of surface biomass. FISH could allow for the identification of residual organisms, and can be targeted to detect active populations of specific organisms such as bacteria known to resist cleaning procedures. This effort is part of a larger study that is concentrated on characterizing the surface and airborne molecular organic contamination background in Johnson Space Center (JSC) Astromaterials curation laboratories and Goddard Space Flight Center (GSFC) spacecraft assembly rooms, and understanding contaminants in the context of cleaning procedures and residual bioburden. Methods: Samples were collected by swabbing surfaces in ISO 5 and ISO 7 equivalent cleanrooms at JSC. Swabs for FISH were fixed in 4% paraformaldehyde (PFA) for 3 hours and then stored in 1:1 ethanol:PBS, while swabs for cell counting were stored in 4% PFA until analysis to avoid any cell loss during centrifugation that could impact quantification of very low biomass samples. Cell counting was performed with SYBR Gold as in [3], but adapted for very low biomass. FISH was performed as in [4], using DAPI as a counterstain for all DNA-containing cells. Negative controls included wells with no probe applied, to test for natural fluorescence, as well as the nonsense probe NONEUB (reverse complement of EUB338) to evaluate non-specific probe binding. Results and Discussion: Cleanroom surfaces had 102-103 cells cm-2. The extremely low biomass of these samples was challenging for enumeration, and required careful and routine use of “field” and laboratory blanks. FISH was performed with the general archaeal and bacterial probes ARCH915 and EUB338 (EUBMIX, [4]), probe GAMBET ([4]), and PSE227, which targets the genus Pseudomonas [5]). The latter two probes were selected because Pseudomonas spp. and other Gammaproteobacteria have not been isolated from cleanroom surfaces but do appear frequently in rRNA gene libraries from these surfaces. While some active bacteria were identified (Fig. 1c), most cells detectable by DAPI did not have a strong or any fluorescent signal (e.g., Fig. 1d), indicating that the vast majority of cells are dead or inactive. This suggests that cleaning protocols are effective at inactivating microbial contaminants, but that dead or inactive cells can remain on surfaces. Cells were often clumped in a weakly autofluorescent matrix, possibly biofilm material (Fig. 1c,d). We also observed other particulate material that was collected by the swabs, including apparent textile fibers (Fig. 1b). Our results are consistent with other studies that show that the bioburden present in clean rooms includes active, dormant, and dead cells. We will discuss how FISH and epifluorescent cell counting could be applied in planetary protection protocols, including the advantages and disadvantages of FISH and cell counting for routine use, as well as different possible applications for more specialized FISH procedures. References: [1] Moissl-Eichinger et al. (2015) Sci Rep, 5, 9156 [2] Hendrickson et al. (2021) Microbiome, 9, 238 [3] Jones et al. (2017) Appl Environ Microbiol, 83, e00909-17 [4] Jones et al. (2015) Appl Environ Microbiol, 81, 1242-1250. [5] Watt et al. (2006) Environ Microbiol, 8, 871-884

C J Huff↗
NASA NTRSDate not supplied

Spaceflight Associated Neuro-Ocular Syndrome: A Brief for Astronaut Candidates

INTRODUCTION: Spaceflight Associated Neuro-ocular Syndrome (SANS) was first described in 2011 as a clinical process involving degradation of visual acuity and structural changes of the eye when exposed to microgravity. This syndrome poses a risk to astronaut vision, safety, and mission performance, especially during extended-duration missions. The modern astronaut cohort is a diverse group of men and women including scientists, engineers, teachers, pilots, business professionals, and artists. Given their diverse backgrounds, it is imperative all crews are educated on SANS risks and potential countermeasures. This education must be comprehensive and easily understood, regardless of academic background or specific expertise. TOPIC: A PowerPoint was created to serve as a presentation and stand-alone educational aid for all astronaut candidates (ASCANS). This medium was chosen as it can be updated dynamically as new information emerges. The brief was split into sections to facilitate organized delivery of complex content in easy-to-understand components. Sections included descriptive statistics, signs and symptoms, outcomes, myths and ongoing research, countermeasures, ongoing surveillance, and unknown and future directions. More research is necessary in order to understand this syndrome, and without continued ASCAN participation in research, acquisition of data will not be possible. These efforts will become increasingly critical with deep space and exploration missions. APPLICATION: We recommend regular use of this brief for all ASCANS, and potentially veteran crewmembers, given the high risks and potentially poor outcomes associated with SANS. For ASCANS, recommendations include that this brief be provided at the start of their training, with a bi-annual refresher course for all astronauts. This ensures they are current on SANS information, given the dynamic nature of this syndrome. Additionally, this brief will be made available to all as a self-study aid, utilized as a refresher immediately prior to launch. It is anticipated that this brief will promote the health, safety, and wellbeing of professional and private crews alike, during and after long-duration spaceflight. RESOURCES: Brunstetter, T., Tarver, B., & Tsung, A. (2022, October). Spaceflight Associated Neuro-ocular Syndrome (Sans) and its Risk to Nasa Astronauts. JSC Aerospace Medicine Clerkship. Houston, TX; Lyndon B. Johnson Space Center. Laurie, S. S., Macias, B. R., Pardon, L. P., Brunstetter, T., Tarver, W. J., Gibson, C. R., Greenwald, S. H., Jasien, K. V., Mason, S., & Tsung, A. (2022). (rep.). Evidence Report: Risk of Spaceflight Associated Neuro-ocular Syndrome (SANS). Houston, TX: National Aeronautics and Space Administration. Mader, T. H., Gibson, C. R., Pass, A. F., Kramer, L. A., Lee, A. G., Fogarty, J., ... & Polk, J. D. (2011). Optic disc edema, globe flattening, choroidal folds, and hyperopic shifts observed in astronauts after long-duration space flight. Ophthalmology, 118(10), 2058-2069. LEARNING OBJECTIVES: • The audience will be able to describe current Spaceflight Associated Neuro-ocular Syndrome (SANS) findings, significance, and countermeasures. • The audience will understand the importance of astronauts’ familiarity with SANS prior to flying and the large risks associated with this syndrome. CME QUESTIONS (3 QUESTIONS, MULTIPLE CHOICE A-D): 1. What is the approximate prevalence rate of SANS in astronauts? A. 22% B. 50% C. 66% D. 80% Answer: C. 2. Which of the ocular findings are NOT associated with SANS? A. Optic disc edema B. Retinal detachment C. Globe flattening D. Chorioretinal folds Answer: B. 3. Which of the following diagnostic technologies are NOT available in-flight? A. Ocular ultrasound B. Retinal photography C. MRI Orbit D. Optical Coherence Tomography (OCT) Answer: C.

Sara Stroble Mason↗
NASA NTRSDate not supplied

The Global Water Monitor: Wetland surface height dynamics for Ecology, Conservation, and Resource Management

The Global Water Monitor (GWM) offers surface water-related products for lakes, river reaches and wetland zones. The surface elevation change products are derived from satellite radar altimeters, such as the Jason/Sentinel series, and can span multiple decades. While the current instruments are profiling, they offer surface water height at specific locations, thus contributing to parallel observation of wetland surface water extent. GWM wetland products are “operational” with routine updates within 1-2days of satellite overpass. There is also assurance of product continuity to at least the end of 2030. Currently, the GWM holds products for a small selection (~40) of diverse wetlands for objectives that focus on conservation and water/fisheries resource monitoring. These sites have been requested by various organizations also looking to the effects of climate change and anthropogenic influences. Many of the current GWM wetland regions are in National Parks such as the Everglades (USA), the Wasur (Rep. Indonesia), and the Kakadu marshes (Australia). They also include coastal river deltas of the Danube, Mekong, Amazon, Orinoco and Ganges Rivers, and the internal Okavango Delta in Botswana. The preliminary set also ensures a diverse range of wetlands e.g., the shallow pot-hole lake region of the Sand Hills and the coastal Black Swamp of the USA, the peat fields of Malaysia and rice growing fields of Yilinzhen in China. Extensive wetlands in Brazil (the Pantanal), South Sudan (the Sudd Marshes) and Belarus (the Pinsk) are also featured, as are the mangrove regions of the Sundarbans (India) and the Laguna Terminos (Mexico). The Usangu wetland (Tanzania) is also included, a focus region where wetland ecology strongly competes with demands from irrigation, livestock, and the needs of downstream hydro-electric power. The nadir-pointing altimeter instruments record height variations regardless of vegetation or canopy cover, and height dynamics at 10-day or monthly resolution reveal seasonal and inter-annual variations as well as longer-term declining or re-charging trends. These products provide a unique, multi-decadal data set that can stand-alone or serve with cross-validation or image-fusion efforts.

Charon Birkett↗
NASA NTRS2024

Spacecraft Modeling, Attitude Determination, and Control: Quaternion-Based Approach

Spacecraft attitude determination and control is an important part of a spacecraft to achieve its designed mission. As of today, many spacecrafts have been successfully launched, and most of them have performed well as they were designed. Many research papers have been published to address the attitude determination and control design problems. Several text books are available for students to learn the technology and for engineers to use as references. The most popular spacecraft models for attitude determination algorithms and control design methods are the Euler angle models and the quaternion models . The Euler angle models have been proved very efficient as the linearized models are controllable, and all standard linear control system design methods are directly applicable. The drawbacks related to the Euler angle methods are (a) the designs based on linearized models may not globally stabilize the original nonlinear spacecraft, i.e., the design may not work when the attitude of the spacecraft is far away from the point where the linearization is performed; (b) the models depend on the rotational sequences, this can be error prone if several teams work on the same project and they use different rotational sequences; (c) for any rotational sequence, there is a singular point where the model is not applicable; and (d) since most attitude determination methods use quaternion to represent the spacecraft attitude, there is a need to transform quaternion into Euler angles. On the other hand, for quaternion models, people have found controllers that can globally stabilize nonlinear spacecraft systems; the models do not depend on rotational sequences and they have no singular point; and the quaternion is provided by attitude determination system and ready to use. The main problem with the quaternion model based control system design is that the linearized quaternion model is not controllable. Therefore, most published design methods heavily rely on Lyapunov functions for the nonlinear spacecraft system. But there is no systematic way to obtain a desired Lyapunov functions. Moreover, the Lyapunov function based designs focus on the closed-loop system stability but pay little attention to the closed-loop system performance. In a series of papers, the author proposed some reduced quaternion models which lead to some controllable linearized spacecraft models. Therefore, all standard linear system theory can be directly applied to analyze and design the spacecraft control systems. We showed that, in some cases, the designed control system is not only optimal for the linearized system, but also globally stabilize the original nonlinear system . Clearly, the reduced quaternion models do not depend on rotational sequences. Due to the special structure of the linearized spacecraft model, some most important design methods, such as LQR design and robust pole assignment design are very simple, enjoy the analytical solutions for some problems, have direct connection to the performance measures, such as settling time, rising time , and percentage of overshoot . All these features are attractive for high quality control system designs. The idea mentioned above is then extended to more spacecraft control problems using specific actuators such as magnetic torque bars and control momentum gyroscopes. These types of actuators may not provide exactly desired torques. Most existing methods use different conversions to get approximate solutions, meaning that these actuators may generate a torque close to but not equal to the desired one. Using the reduced quaternion models that incorporate the actuators into the system model, the control inputs are not torques but the operational parameters. The main benefit of this idea is that the control actions are not approximate but accurate. As all actuators have their operational limit, design with input constraints are also considered in this book by using recently developed interior-point optimization techniques. This book grows up from my research on the spacecraft attitude determination and control design methods in more than a decade which is focused on using reduced quaternion models because of their merits stated above. The book provides all necessary background materials on orbital dynamics, rotations and quaternion, frequently used reference frames, transformations between reference frames, space environment and disturbance torques, ephemeris astronomical vector calculations and measurement instruments, spacecraft control actuators and their models, so that the readers will get a global picture and can apply all these information into the spacecraft system modeling, attitude determination, and spacecraft control system designs, which is the main purpose of this book. This book is different from existing books in that we focus on quaternion based spacecraft control system designs and we consider only attitude control system design related problems, from spacecraft modeling, to attitude determination and estimation, to control system design method selection, to control algorithm development, and to the simulation of the control system designs. Moreover, this book addresses different attitude control tasks in the spacecraft life cycle, including spacecraft maneuver, orbit raising, attitude control, and rendezvous. Finally, this book emphasizes the state space design methods rather than the classical frequency design methods.

Attitude determination and control↗
DOE OSTI2020

Subtask 1.3 – Integrated Carbon Capture and Storage for North Dakota Ethanol Production

The Energy & Environmental Research Center (EERC), in partnership with Red Trail Energy, LLC (RTE), a North Dakota ethanol producer; the North Dakota Industrial Commission (NDIC) Renewable Energy Program (REP); and the U.S. Department of Energy (DOE), conducted a feasibility and implementation study for a commercial carbon capture and storage (CCS) effort. This subtask provided technical support and developed recommended practices of how small-scale industrial CO2 emitters (<1,000,000 tonnes of CO2 emitted annually) may economically deploy CCS. The 64-million-gallon dry mill RTE ethanol facility, emitting an average 180,000 tonnes of CO2 annually, was the subject of the case study. The positive outcome of this research, which shows technical and economic potential for ethanol–CCS in North Dakota, has resulted in RTE acquiring an approved Permit to Drill on December 2, 2019, for a stratigraphic test well in early 2020, a necessary step toward a North Dakota CO2 Storage Facility Permit (SFP) for the RTE CCS effort. Outcomes include 1) validating the Broom Creek Formation as a regional target for CCS, 2) determining the full carbon life cycle of an industrial fuel production facility with CCS, 3) developing a field implementation plan (FIP) for small-scale CCS, and 4) determining the validity and pathway for using CCS to meet low-carbon fuel (LCF) standards. The technical team included the EERC, RTE, Trimeric Corporation, Schlumberger Carbon Services, and Computer Modelling Group (CMG). Findings from activities conducted November 2016 – May 2020 are summarized as follows. Several key steps have been accomplished toward validating the Broom Creek Formation as a CO2 injection and storage target at the RTE CCS site, including verification of the presence and structure of sandstone layers that may comprise the potential CO2 storage reservoir and the several thousand feet of overlying confining zone. Work included site characterization using existing data, interpretation of seismic data within the study area, and geologic modeling simulation of CO2 injection. Interpreted results estimate 3000 feet of confining zone between the Broom Creek Formation (storage target) and the lowermost underground source of drinking water (e.g., the Fox Hills Formation). The thickness of the Broom Creek injection target varies 230–420 ft within the survey area. Results were used to inform the location of a stratigraphic test well and associated characterization test program. No impediments were identified within the targeted CO2 storage complex that would prevent the project from moving forward. A stratigraphic test well is the next step to validate these results and to acquire remaining data necessary to develop a North Dakota CO2 SFP application. The EERC generated full carbon life cycle estimates for CCS integration with the RTE ethanol facility. Results indicated that an average 40% reduction in CO2 emissions is possible through CCS implementation. Approximately half of the carbon in the overall life cycle for a dry mill ethanol plant is generated through the fermentation process and emitted to the atmosphere; this is the CO2 stream targeted for CCS. The remaining carbon is attributed to corn feedstock farming (diesel, fertilizer), energy for fuel processing (natural gas, electricity), and transportation (diesel) of the fuel product. Life cycle carbon estimates are also affected by the anticipated energy consumption of a potential capture facility, which depend on the type of CO2 product generated. For example, a 30%–40% net CO2 emission reduction is estimated if a liquefied CO2 facility were incorporated compared to a 40%–50% net CO2 reduction if a supercritical “injection-grade” CO2 product is generated; i.e., more energy is required to further refine the CO2 stream, affecting the full carbon life cycle estimates. A CCS FIP was developed and initiated at the RTE CCS site, resulting in the development of several guidance documents: a CO2 Capture Process Design Package, a North Dakota CO2 geologic Storage Permits Template, and a Public Outreach Package for CCS in North Dakota. General FIP components include CO2 capture system, pipeline and well designs; monitoring, verification, and accounting (MVA) plans; geologic characterization and testing programs; and permitting and outreach plans. Vendor bids were also acquired for the CO2 liquefaction facility. Near-surface characterization (groundwater and soil gas sampling) and geologic characterization (seismic survey) were initiated to inform development of a UIC Class VI-compliant MVA plan compliant with a North Dakota CO2 SFP. Designs (well and geologic testing) were completed for a stratigraphic test well compliant with a North Dakota CO2 SFP. In addition, the outreach plan was executed, including community open houses, meetings with city/county/state officials, and development of public materials. Although other entities continued to mature incentive programs in 2019–2020, California and the Internal Revenue Service (IRS) currently provide the most advanced economic opportunities for CCS integrated with fuel production. The California Low-Carbon Fuel Standard (LCFS) adopted a CCS Protocol in January 2019, allowing submittal of a design-based pathway (DBP) application for an approved temporary (not certified) carbon intensity value for a fully engineered facility. An ethanol–CCS DBP application to the California LCFS Program (officially approved February 28, 2020) was developed to show that the RTE CCS effort meets LCFS requirements. The approved DBP provides confidence to advance the project and supports potential investments. Other entities continue to mature incentive programs. The IRS issued guidance in February 2020 that addresses the definition of beginning of construction and revenue procedure on partnerships for the Enhancement of Carbon Dioxide Sequestration Credit (a.k.a. Section 45Q) CCS tax credit program; the IRS anticipates issuing further guidance on issues such as secure geologic storage, utilization qualifications, and recapture of claimed credits. Maturing incentive programs coupled with workable permitting regulations provide confidence to advance CCS projects in North Dakota and support financial investment to proceed with designing, constructing, and implementing CCS projects at small-scale fuel production facilities. The largest hurdles for CCS implementation at small-scale industrial systems are often business/economic-related (i.e., not technical). Market uncertainty already exists for agriculture-based alternative fuels such as corn ethanol, for which production has increased by ~33%, and prices have correspondingly lowered since 2015. Passing the Section 45Q tax credit program improves economic feasibility for CCS but may require external investors for a small business to achieve maximum benefits. Public–private partnerships with NDIC and DOE have resulted in foundational technical and regulatory knowledge, growing stakeholder confidence, and a pathway to implementation that enables similar industrial CCS projects in the region to advance. This subtask was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by NDIC and RTE. The authors would also like to thank CMG, ESRI, IHS, Neuralog, and Schlumberger for allowing the use of their software packages in support of this work.

42 ENGINEERING↗
DOE OSTI2021

Technoeconomic Benefits of Film-Forming Amine Products Applied to Steam Surface Condensers

In a conventional Rankine cycle, the majority of power plants employ surface condensers that use pumped cooling water to reject heat from the cycle. In such cases, heat rejection occurs in a shell and tube heat exchanger by film-wise condensation of low-pressure steam on stainless steel, titanium, brass, or copper-nickel tubing. To improve the thermal performance of steam surface condensers, a replenishable film-forming substance (FFS) can be ap-plied to the condenser tubing to promote efficient dropwise condensation. Conventionally, film-forming amine prod-uct (FFAP) coatings protect boiler surfaces from oxidative corrosion, which substantially reduces the operation and maintenance costs. To quantify the technical and economic benefits of FFAP coatings applied to condenser tubing due to the promotion of dropwise condensation, a thermal resistance network model was established. Using a rep-resentative steam surface condenser, the improvements in thermal performance (overall heat transfer coefficient) and process parameters (net plant efficiency, cooling water flowrate, and turbine backpressure) were determined due to the enhancement in the condensation heat transfer coefficient. Experimentally measured condensation heat transfer coefficients for common condenser materials were compared with the modeling results and were found to be within attainable bounds. Lastly, the trend in total heat exchanger cost reduction is generalized to understand the trade-off between reduced surface area for heat rejection and increase in coating application costs for a re-plenishable coating system.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Localization and reduction of superconducting quantum coherent circuit losses

Quantum sensing and computation can be realized with superconducting microwave circuits. Qubits are engineered quantum systems of capacitors and inductors with non-linear Josephson junctions. They operate in the single-excitation quantum regime, photons of $27 \mu$eV at 6.5 GHz. Quantum coherence is fundamentally limited by materials defects, in particular atomic-scale parasitic two-level systems (TLS) in amorphous dielectrics at circuit interfaces.[1] The electric fields driving oscillating charges in quantum circuits resonantly couple to TLS, producing phase noise and dissipation. We use coplanar niobium-on-silicon superconducting resonators to probe decoherence in quantum circuits. By selectively modifying interface dielectrics, we show that most TLS losses come from the silicon surface oxide, and most non-TLS losses are distributed throughout the niobium surface oxide. Through post-fabrication interface modification we reduced TLS losses by 85% and non-TLS losses by 72%, obtaining record single-photon resonator quality factors above 5 million and approaching a regime where non-TLS losses are dominant. [1]M\"uller, C., Cole, J. H. & Lisenfeld, J. Towards understanding two-level-systems in amorphous solids: insights from quantum circuits. Rep. Prog. Phys. 82, 124501 (2019)

Altoé, M Virginia P↗
DOE OSTI2021

The Fast Modular Reactor (FMR) Pre-Application Regulatory Engagement Plan

The Fast Modular Reactor (FMR) is a 50 MWe Gascooled Fast Reactor (GFR) being developed by General Atomics Electromagnetic Systems (GA-EMS) under U.S. Department of Energy’s (DOE’s) Advanced Reactor Demonstration Program (ARDP), specifically Advanced Reactor Concepts 2020 (ARC-20). The 3-year conceptual design of the FMR is being conducted with verifications of key metrics in fuel, safety, and operational performance. GAEMS is pursuing design, licensing, and commercialization of the proposed reactor, with demonstration by 2030 and deployment by the mid-2030s. The U.S. Nuclear Regulatory Commission (NRC) recommends the pre-application regulatory engagement to provide for early identification of regulatory requirements for advanced reactors and to provide all interested parties with a timely, independent assessment of the safety and security characteristics of advanced reactor designs. As such, GAEMS is developing a pre-application regulatory engagement plan (REP) of the FMR.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

SERPENT 2 and TRIPOLI-4 neutronics benchmarking of the Jules Horowitz reactor

Jules Horowitz Reactor (JHR) is a future center for nuclear material testing in Europe, currently under construction at CEA Cadarache in southern France. It has been modelled extensively with CEA's HORUS3D/N neutron calculation package, that includes a Monte-Carlo neutron transport code TRIPOLI-4. In order to support the future computational analyses on the reactor core physics, VTT's Monte Carlo neutronics code SERPENT 2 has been used to create an alternative model of the JHR, taking advantage of the pre-existing Constructive Solid Geometry (CSG) structures on which the TRIPOLI-4 model was built. This work describes a benchmark, in which two JHR core configurations were analyzed using both of these models. The first configuration is a fresh fuel core at the beginning of life, in which aluminum based dummy-devices are installed in the reactor test positions. The second configuration represents the end-of-cycle equilibrium core with a heterogeneous burnup distribution, in which CALIPSO devices containing cladding material samples are installed at the in-core experimental positions, while the reflector positions are occupied by DEN-REP devices containing UO{sub 2} fuel. Neutron flux spectra and heat deposition are the parameters of interest in this study, due to their high importance in creating the desired experimental irradiation environment. The impact of delayed gamma energy deposition will be studied in detail, since the two models account for it with different methods. This work aims to establish a SERPENT 2 model of JHR, understanding its differences and agreements with TRIPOLI-4, and discussing its potential future applications. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Porewater chemistry in Typha-dominated brackish tidal marsh, PIE LTER, Plum Island Sound, MA, July 2022–September 2024

This dataset contains profile measurements of porewater constituents taken on 3-4 days across the growing seasons in 2022, 2023, and 2024 in a tidal brackish marsh within the Plum Island Ecosystems Long Term Ecological Research site (PIE LTER), located in the Plum Island Sound, Massachusetts (MA). Measurements were taken to monitor changes in porewater chemistry induced by seasonal saltwater intrusion at the site. Samples were taken in two locations: one was close to the creek bank and the other in the marsh interior. Water was sampled from 2-5 depths between the surface to 50cm using a sipper consisting of a hollow stainless steel rod with an opening at the end similar to that described in (Berg & McGlathery, 2001). The rod was pushed into the sediment to the desired depth, typically every 10cm, and water samples were taken by syringe. Water was not obtained at all depths. Samples were preserved and analyzed in the lab. Metadata files Typha_porewater_sipper_dd.csv and Typha_porewater_sipper_flmd.csv contain detailed information on data variables, sampling and QA/QC methods, and site location.

54 ENVIRONMENTAL SCIENCES↗