Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESIDUAL STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Photoluminescence Spectroscopy to Determine Residual Stresses in Glass-to-Metal Seals

In components with two materials, such as glass-to-metal (GtM) seals, residual stress can reduce long-term reliability. Therefore, it is important to be able to accurately measure residual stress within these components. The residual stress can be from a large strain due to the mismatch of thermo-physical response of the two materials or a small strain due to stress and/or structural relaxation. Both modeling and experimental measurements were conducted on multiple GtM seals constructed with CGI 930 glass with purposely added alumina particles. The alumina particles have an established Cr fluorescence pattern and the shift in position of these peaks can accurately measure the strain of the alumina crystals. Photoluminescence spectroscopy (PLS) technique was utilized due to its non-destructive nature and high spatial resolution. PLS scans of these components were analyzed and compared to the models developed previously.

36 MATERIALS SCIENCE↗

NEUTRON DIFFRACTION MEASUREMENT OF RESIDUAL STRESSES IN FRICTION STIR PROCESSED NANOCOMPOSITE SURFACE LAYER

Friction stir processing (FSP) was successfully used to stir and mix nano-sized Al2O3 particles into a Al6061-T6 aluminum plate to form a nanocomposite layer up to 3 mm thick. This nanocomposite surface has demonstrated significantly improved surface hardness, yield strength, and wear-resistance without sacrificing the substrate ductility and conductivity. Neutron diffraction analysis was conducted to determine the residual stress distribution in the nanocomposite surface layer. For comparison, the residual stress of the aluminum surface that was processed similarly but had no particle involved was also measured. Results showed that the macro-level residual stresses in the FSP zone without particles are low due to the annealing effect induced by the long heating time and large heat input. The macro-level residual stresses in the FSP-processed Al-Al2O3 nanocomposite zone are tensile up to 100 MPa in all three directions. The details of the results will be further discussed in the paper.

36 MATERIALS SCIENCE↗

Evaluation of a thermomechanical model for prediction of residual stress during laser powder bed fusion of Ti-6Al-4V

The build-up of residual stresses in a part during laser powder bed fusion provides a significant limitation to the adoption of this process. These residuals stresses may cause a part to fail during a build or fall outside the specified tolerances after fabrication. In the present work a thermomechanical model is used to simulate the build process and calculate the residual stress state for Ti–6Al–4V specimens built with continuous and island scan strategies. A layer agglomeration, or lumping, approach is used to speed up the computations. A material model is developed to naturally capture the strain-rate dependence and annealing behavior of Ti–6Al–4V at elevated temperatures. Conclusions from the thermomechanical simulations showed good agreement with synchrotron X-ray diffraction measurements used to determine the residual elastic strains in these parts. Yet, the experimental measurements showed higher residual strains for the specimen built with an island scan strategy; a trend not fully captured by the simulations. Parameter studies were performed to fully understand the advantages and limitations of the current simulation methodology. Reasons for both the computational and experimental findings are discussed.

36 MATERIALS SCIENCE↗

Forging And Milling Contribution On Residual Stresses For A Textured Biphasic Titanium Alloy

Ti-10V-2Fe-3Al is a biphasic titanium alloy ({alpha}+{beta}) used in aeronautical applications for its mechanical properties, such as its yield strength of 1200 MPa and it weighs 40% less than steel. This alloy is particularly useful for vital parts with complex geometry, because of its high forging capability. In order to predict the capability for fatigue lifetime, the designers need to know the residual stresses. X-Ray diffraction is the main experimental technique used to determine residual stresses on the surface. In this case, stress levels are primarily influenced by the complex forging and milling process. On this alloy in particular, it may be difficult to characterize stress due to modification of the microstructure close to the surface. Results obtained by x-ray analysis depend on the correct definition of the shape of the diffraction peaks. The more precisely defined the position of the peak, the more accurately the stresses are evaluated. This paper presents a method to detect if residual stresses can be characterized by x-ray diffraction. The characterization of hardness seems to be a relevant technique to quickly analyze the capability of x-ray diffraction to determine residual stresses.

36 MATERIALS SCIENCE↗

Neutron residual stress measurement and numerical modeling in a curved thin-walled structure by laser powder bed fusion additive manufacturing

Severe residual stresses in metal parts made by laser powder bed fusion additive manufacturing processes (LPBFAM) can cause both distortion and cracking during the fabrication processes. Limited data is currently available for both iterating through process conditions and design, and in particular, for validating numerical models to accelerate process certification. In this work, residual stresses of a curved thin-walled structure, made of Ni-based superalloy Inconel 625™ and fabricated by LPBFAM, were resolved by neutron diffraction without measuring the stress-free lattices along both the build and the transverse directions. The stresses of the entire part during fabrication and after cooling down were predicted by a simplified layer-by-layer finite element based numerical model. The simulated and measured stresses were found in good quantitative agreement. The validated simplified simulation methodology will allow to assess residual stresses in more complex structures and to significantly reduce manufacturing cycle time.

36 MATERIALS SCIENCE↗

MOOSE Optimization Module Overview: Application to Residual Stress Inversion in Nuclear Fuel Plates

Manufacturing methods, material selections and unique plate geometries used in low enriched uranium plate fuels for the High Performance Research Reactor (HPRR) have led to concerns about the residual stresses effect on bond strength of the fuel/cladding interfaces and overall fuel performance under irradiation. The current HPRR plate fuel test program performed residual stress calculations using the contour method with experimental displacement data obtained by incrementally cutting the plate fuel. In this work, we use a gradient based inverse optimization module developed within the MOOSE framework to estimate normal and shear residual stresses within the plate fuels using displacement data taken from a cut placed in the HPRR fuel plate. These results are verified against residual stress calculations obtained from the contour method. The inversion protocol used in this work utilizes two meshes to separately discretize the physics and parameter space. This allows a fine mesh to be used to fully resolve the physics and geometry of the forward problem. A coarser mesh is used to resolve the parameter space with spatially varying mesh density determined from a sensitivity analysis. The adaptive resolution of the parameter space essentially has the effect of regularization as it is designed to achieve the bias-variance tradeoff.

42 ENGINEERING↗

Neutron Residual Stress Mapping of Repaired Spent Nuclear Fuel Welded Stainless-Steel Canisters

Stress corrosion cracking (SCC) caused by atmospheric deposition and deliquescence of aggressive compounds such as chloride-containing salts or oxidized sulfur species may pose a potential issue to the extended service life of spent nuclear fuel (SNF) storage canisters. When a chemically susceptible material is exposed to a hostile environment (e.g., coastal salt air) for a sufficient length of time, SCC may occur at locations on the canister which have undergone high tensile residual stress. These locations are often found in weld zones and the heat-affected zones (HAZ) of welded joints. Ideally, these cracks could be repaired by traditional fusion welding techniques, but the highly localized heat input of the repair welding may introduce additional high tensile residual stress and could increase the risk for future SCCs. This paper presents the results of neutron residual stress mapping of as-welded and repaired stainless steel specimens. The as-welded specimens were provided by Sandia National Laboratories from a canister mock-up manufactured using procedures similar to those used for actual canister production. ASME-qualified gas-tungsten arc welding (GTAW) was used to repair the specimens, and post-repair residual stresses were measured using neutron diffraction at the Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR). As-welded and repaired specimen residual stress distributions are evaluated and compared.

Chatzidakis, Stylianos↗

3D mapping of residual stresses in growing grains of partially recrystallized Gum Metal

The crystallographic orientations and residual stresses within recrystallizing grains in partially recrystallized beta titanium-Gum Metal-were examined non-destructively in 3D using synchrotron Differential Aperture X-ray Microscopy. Contrary to common assumptions, significant local stresses and stress variations are observed within the recrystallizing grains. The results reveal that the development of these local residual stresses depends on the plastic deformation mode and material's elastic constants, rather than grain properties such as size and orientation, or even the material's yield stress. This work provides insights valuable for the design of advanced materials with heterogeneous microstructures.

36 MATERIALS SCIENCE↗

Residual-stress-induced grain growth of twinned grains and its effect on formability of magnesium alloy sheet at room temperature

A magnesium alloy sheet was subjected to in-plane compression along with a vertical load to avoid buckling during compression. Pre-compressed specimens machined from the sheet were annealed at different temperatures and the changes in microstructure and texture were observed using electron back scattered diffraction (EBSD). Twinned grains preferentially grew during annealing at 300 °C, so that a strong texture with the < 0001 > direction parallel to the transverse direction developed. EBSD analysis confirmed that the friction caused by the vertical load induced inhomogeneous distribution of residual stress, which acted as an additional driving force for preferential grain growth of twinned grain during annealing. The annealed specimen showed excellent formability. - Highlights: • A magnesium alloy sheet subjected to in-plane compression under a vertical load • The vertical load induced inhomogeneous distribution of the residual stress. • The residual stress acted as an additional driving force for grain growth. • The annealed specimen with strong non-basal texture showed excellent formability.

36 MATERIALS SCIENCE↗

Resonance ultrasound prediction of residual stress within a hybrid layer for additively manufactured samples

Hybrid additive manufacturing (AM) involves secondary processes or energy sources to alter specified locations within the build volume. Each hybrid step can refine the grain size, increase dislocation density, or modify residual stresses. Typically, the changes in mechanical properties are not confined within a single layer but have a compounding effect on preceding layers. Existing methods of measuring AM residual stress are limited in terms of their sensitivity, or they are destructive measurements. We propose using resonant ultrasound spectroscopy (RUS) to measure the residual stress in hybrid-AM components noninvasively, based on changes to the resonances, compared to a stress-free component. In this paper, we use finite element models to simulate residual stress in hybrid-AM components and to examine the sensitivity of RUS measurements in terms of frequency shifts and mode shapes with respect to single hybrid layers. Then, the RUS results are used to predict stress for a layer at a known location with unknown stress. Here, the approach highlights the capabilities of RUS to address an AM characterization challenge.

36 MATERIALS SCIENCE↗

Measuring the elastic modulus and residual stress of freestanding thin films using nanoindentation techniques

A new method is proposed to determine the elastic modulus and residual stress of freestanding thin films based on nanoindentation techniques. The experimentally measured stiffness-displacement response is applied to a simple membrane model that assumes the film deformation is dominated by stretching as opposed to bending. Dimensional analysis is used to identify appropriate limitations of the proposed model. Experimental verification of the method is demonstrated for Al/0.5 wt% Cu films nominally 22 {micro}m wide, 0.55 {micro}m thick, and 150, 300, and 500 {micro}m long. The estimated modulus for the four freestanding films match the value measured by electrostatic techniques to within 2%, and the residual stress to within 19.1%. The difference in residual stress can be completely accounted for by thermal expansion and a modest change in temperature of 3 C. Numerous experimental pitfalls are identified and discussed. Collectively, these data and the technique used to generate them should help future investigators make more accurate and precise measurements of the mechanical properties of freestanding thin films using nanoindentation.

36 MATERIALS SCIENCE↗

Residual stress distribution in steel butt welds measured using neutron and synchrotron diffraction.

70 keV synchrotron radiation and thermal neutrons have been employed to investigate the residual stress characteristics in a fully restrained, steel, butt weld. The focus is on the values of the subsurface and through-thickness strain/stress variation in the middle of the weld. The advantages and limitations of the techniques have been addressed, in relation to the gauge volume, the stress-free reference sample and positioning. The measurement of residual stress around the weld achieved in this work significantly improves the resolution at which residual stress in welded components has been determined.

36 MATERIALS SCIENCE↗

MODELS FOR ESTIMATING THE AUTOFRETTAGE PRESSURE AND RESIDUAL STRESSES IN WALLS OF TYPE 2 PRESSURE VESSELS

Autofrettage is a manufacturing process used during fabrication of Type 2 pressure vessels designed for usage at high pressures to enhance the fatigue life. The process locks high compressive residual stresses in the vessel’s liner wall that reduce the maximum and the mean stress during service loading. To achieve a consistent residual stress profile across the wall of the vessel, the choice of autofrettage pressure is critical. Several finite element analyses runs were conducted to estimate the correct autofrettage pressure that is a function of the yield strength of the liner material, the wall thickness, and the outside diameter of the liner for a wrap thickness of 17.06 mm (48 wire layers). From the finite element analyses results, models were developed to estimate the correct autofrettage pressure and the residual stress distribution across the liner wall as a function of the yield strength of the liner material, the wall thickness, and the outside diameter of the liner.

08 HYDROGEN↗

Residual stress evaluation of components produced via direct metal laser sintering

Direct metal laser sintering is an additive manufacturing process which is capable of fabricating three-dimensional components using a laser energy source and metal powder particles. Despite the numerous benefits offered by this technology, the process maturity is low with respect to traditional subtractive manufacturing methods. Relationships between key processing parameters and final part properties are generally lacking and require further development. In this study, residual stresses were evaluated as a function of key process variables. The variables evaluated included laser scan strategy and build plate preheat temperature. Residual stresses were measured experimentally via neutron diffraction and computationally via finite element analysis. Good agreement was shown between the experimental and computational results. Results showed variations in the residual stress profile as a function of laser scan strategy. Compressive stresses were dominant along the build height (z) direction, and tensile stresses were dominant in the x and y directions. Build plate preheating was shown to be an effective method for alleviating residual stress due to the reduction in thermal gradient.

36 MATERIALS SCIENCE↗

ASSESSMENT OF RESIDUAL STRESSES IN SRS AND HANFORD 3013 INNER AND CONVENIENCE CANS

Chloride stress corrosion cracking (SCC) is a plausible corrosion mechanism for the stainless steel 3013 containers during their lifetime for plutonium material storage if sufficient electrolyte is present within the container. Contributing factors for SCC, such as fabrication and welding residual stresses, are present in the 3013 cans. Convenience and inner cans from both Hanford and SRS are made by a flow form process, which cold works the stainless steel during fabrication. Additionally, the inner cans also are sealed at the can top with a closure weld to the sealing plug. Only SRS and Hanford were tested since moisture levels were significant for SCC. As part of the 3013 corrosion plan for FY09, testing in a boiling magnesium chloride solution was performed on actual 3013 convenience and inner cans to determine if the residual stresses were sufficient for the initiation and propagation of SCC. Additional testing in a 40% calcium chloride solution was also performed on 304L stainless steel SCC coupons, i.e. stressed teardrop-shaped samples (teardrops), and an inner can welded top to provide comparative results and to assess the effect of residual stresses in a less aggressive environment. The testing performed under this task consisted of 3013 inner and convenience cans and 304L teardrops exposed to a boiling magnesium chloride solutions per ASTM G36 and a 40% calcium chloride solution at 100 C following the guidance of ASTM G123. Cracking occurred in all can types including the inner can bottom and welded top and the bottoms of the SRS and Hanford convenience cans when exposed to the boiling magnesium chloride solution at 155 C. Cracking occurred at different times indicative of the residual stress levels in the cans. 304L teardrops cracked in the shortest time interval and therefore provide a conservative estimate for can performance. Testing in a 40% calcium chloride solution at 100 C demonstrated that cracking occurs in a less aggressive environment but at significantly longer times than in the boiling magnesium chloride. Vapor space cracking was also found to occur in the inner can welded top exposed over the boiling magnesium chloride solution and on 304L teardrops exposed over a hot calcium chloride solution.

36 MATERIALS SCIENCE↗

Residual Stresses in DC cast Aluminum Billet: Neutron Diffraction Measurements and Thermomechanical Modeling

Thermally-induced residual stresses, generated during the industrial Direct Chill casting process of aluminum alloys, can cause both significant safety concerns as well as the formation of defects during down-stream processing. Although these thermally induced strains can be partially relieved by permanent deformation, cracks will be generated either during solidification (hot tears) or post-solidification cooling (cold cracks) when stresses exceed the deformation limit of the alloy. Furthermore, the thermally induced strains result in the presence of large internal stresses within the billet before further processing steps. Although numerical models have been previously developed to compute these residual stresses, most of the computations have been validated only against measured surface distortions. In the present work, the variation in residual elastic strains and stresses in the steady state regime of casting has been measured as a function of radial position using neutron diffraction in an AA6063 grain-refined cylindrical billet. These measurements have been carried out on the same billet section at Poldi at PSI-Villigen and at Salsa at ILL-Grenoble and compare favorably. The results are used to validate a thermo-mechanical finite element casting model and to assess the level of stored elastic energy within the billet.

36 MATERIALS SCIENCE↗

Methods of Measuring Residual Stresses in Additively Manufactured 316L Stainless Steel

The microstructure of AM 316L stainless steel Is different from steel manufactured using conventional methods e.g. casting and forging. Data on the effects of residual stresses in the structural integrity and importance of AM parts (fatigue behavior) must be quantified. Evaluate different methods and identify a viable process for determining residual stresses in 316L stainless steel. Next step is to conduct measurements of residual stresses of samples fabricated by different manufacturers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

From cells to laminate: probing and modeling residual stress evolution in thin silicon photovoltaic modules using synchrotron X-ray micro-diffraction experiments and finite element simulations

Fracture of silicon crystalline solar cells has recently been observed in increasing percentages especially in solar photovoltaic (PV) modules involving thinner silicon solar cells (<200 μm). Many failures due to fracture have been reported from the field because of environmental loading (snow, wind, etc.) as well as mishandling of the solar PV modules (during installation, maintenance, etc.). However, a significantly higher number of failures have also been reported during module encapsulation (lamination) indicating high residual stress in the modules and thus more prone to cell cracking. Here in this paper we report through the use of synchrotron X-ray submicron diffraction coupled with physics-based finite element modeling, the complete residual stress evolution in mono-crystalline silicon solar cells during PV module integration process. For the first time, we unravel the reason for the high stress and cracking of silicon cells near soldered inter-connects. Our experiments revealed a significant increase of residual stress in the silicon cell near the solder joint after lamination. Moreover, our finite element simulations show that this increase of stress during lamination is a result of highly localized bending of the cell near the soldered inter-connects. Further, the synchrotron X-ray submicron diffraction has proven to be a very effective way to quantitatively probe mechanical stress in encapsulated silicon solar cells. Thus, this technique has ultimately enabled these findings leading to the enlightening of the role of soldering and encapsulation processes on the cell residual stress. This model can be further used to suggest methodologies that could lead to lower stress in encapsulated silicon solar cells, which are the subjects of our continued investigations.

14 SOLAR ENERGY↗