Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Point Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Examining the Economic Optimality of Automatic Generation Control

The automatic generation control (AGC) system is temporally situated between economic dispatch and synchronous generator dynamics, and its primary role is to regulate frequency within and tie-line flows between control areas. Given appropriate choice of participation factors (feed-forward controller gains that govern the disaggregation of the area-level power requirement to individual generators), the AGC can be engineered to nudge system dynamics toward a steady-state operating point corresponding to economic optimality. This paper establishes necessary and sufficient conditions under which a widely accepted choice of participation factors guarantees the alignment of steady-state synchronous generator outputs with a global minimum of a prototypical economic dispatch problem. In so doing, it resolves several ambiguities and formalizes technical assumptions governing the role of the standard AGC architecture in the context of economic dispatch and steady-state operation. Numerical case studies tailored to a modified version of the New England 39-bus 10-machine test system validate the theoretical results.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Implementation and validation of optimal start control strategy for air conditioners and heat pumps

Commercial buildings are responsible for approximately 20 % of the total energy consumption and greenhouse gas emissions in the United States. Over 85 % of these buildings lack building automation systems, and many are small (<50,000 square feet), underserved, and use rooftop units (RTUs) for heating, ventilation, and air-conditioning needs. Because these buildings lack proper energy management systems, several operational deficiencies lead to excess energy consumption. Studies have shown that managing the RTUs’ heating and cooling set points, schedules, setbacks, and optimal start can result in a 20 % to 25 % reduction in electricity consumption in small commercial buildings. These buildings typically use fixed schedules to start the RTUs 60 to 120 min before occupancy begins, which results in excess energy consumption. This paper presents research that demonstrates and evaluates the performance of four optimal start methods, which utilize data-based modeling as a key element in facilitating adaptive control in response to time-varying inputs while requiring minimal sensor inputs. The evaluation found energy savings in two commercial buildings equipped with RTUs by periodically alternating four different optimal start models during the cooling and heating season. The resulting energy savings are positive for all models and range from 2 to 5 kWh/day/unit. The units on the east side of the building showed higher savings, while interior units showed greater variability in savings due to the differences in capacities and room sizes. Savings were considerably greater during the heating season compared to the cooling season. The performance of all four models on Mondays was poor; models suggested a shorter optimal start time, which resulted in relatively larger errors. Finally, the future work will look at using a different model for the days after weekends and holidays.

42 ENGINEERING↗
DOE OSTI2023

Investigating and Optimizing the Lysate-Based Expression of Nonribosomal Peptide Synthetases Using a Reporter System

Lysate-based cell-free expression (CFE) systems are accessible platforms for expressing proteins that are difficult to synthesize in vivo, such as nonribosomal peptide synthetases (NRPSs). NRPSs are large (>100 kDa), modular enzyme complexes that synthesize bioactive peptide natural products. This synthetic process is analogous to transcription/translation (TX/TL) in lysates, resulting in potential resource competition between NRPS expression and NRPS activity in cell-free environments. Moreover, CFE conditions depend on the size and structure of the protein. Here, a reporter system for rapidly investigating and optimizing reaction environments for NRPS CFE is described. This strategy is demonstrated in E. coli lysate reactions using blue pigment synthetase A (BpsA), a model NRPS, carrying a C-terminal tetracysteine (TC) tag which forms a fluorescent complex with the biarsenical dye, FlAsH. A colorimetric assay was adapted for lysate reactions to detect the blue pigment product, indigoidine, of cell-free expressed BpsA-TC, confirming that the tagged enzyme is catalytically active. An optimized protocol for end point TC/FlAsH complex measurements in reactions enables quick comparisons of full-length BpsA-TC expressed under different reaction conditions, defining unique requirements for NRPS expression that are related to the protein’s catalytic activity and size. Importantly, these protein-dependent CFE conditions enable higher indigoidine titer and improve the expression of other monomodular NRPSs. Notably, these conditions differ from those used for the expression of superfolder GFP (sfGFP), a common reporter for optimizing lysate-based CFE systems, indicating the necessity for tailored reporters to optimize expression for specific enzyme classes. In conclusion, the reporter system is anticipated to advance lysate-based CFE systems for complex enzyme synthesis, enabling natural product discovery.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Riemannian Optimization Applied to AC Optimal Power Flow: Preprint

The nonlinear, nonconvex AC optimal power flow problem is of growing importance as the nature of the power grid evolves. This problem can be difficult to solve for interior point methods. However, the advent of optimization algorithms over smooth Riemannian manifolds presents an alternative approach. The nonlinear, nonconvex constraints in the AC power flow problem form an embedded submanifold of Euclidean space. In this paper, the authors explore the performance of Riemannian optimization algorithms for the ACOPF problem where the optimization is performed directly on the AC power flow manifold. They demonstrate that these are viable computational alternatives to interior point methods. This is done by using Julia and the packages PowerModels.jl and Manopt.jl.

manifold optimization↗
DOE OSTI2020

A Combined Day-ahead and Real-time approach for Scheduling Real and Reactive power dispatch of Battery Energy Storage System

A combined day-ahead (look-ahead) and real-time optimization approach is proposed to schedule BESS real and reactive power dispatch. The look ahead scheduling agent maximizes profit and essentially performs the function of energy arbitrage by looking at forecasted prices, network constraints and BESS operating conditions to generate real power dispatch schedule. While this schedule is followed, the real time optimization agent computes an optimum reactive power set-point (for a particular objective function) using optimal power flow framework. The concepts are implemented by co-simulating legacy tools and demonstrated on a large real world distribution system. In addition to the profits from energy arbitrage, optimum reactive power set point computation results in achieving desirable network attributes like flat voltage profiles and minimizing voltage deviations from desired value.

Bhatti, Bilal A.↗
DOE OSTI2025

Implementation of McMurchie–Davidson Algorithm for Gaussian AO Integrals Suited for SIMD Processors

We report an implementation of the McMurchie− Davidson evaluation scheme for 1- and 2-particle Gaussian AO integrals designed for processors with Single Instruction Multiple Data (SIMD) instruction sets. Like in our recent MD implementation for graphical processing units (GPUs) [Asadchev, A.; Valeev, E. F.. J. Chem. Phys. 2024, 160, 244109.], variable-sized batches of shellsets of integrals are evaluated at a time. By optimizing for the floating point instruction throughput rather than minimizing the number of operations, this approach achieves up to 50% of the theoretical hardware peak FP64 performance for many common SIMD-equipped platforms (AVX2, AVX512, NEON), which translates to speedups of up to 30 over the state-of-the-art one-shellset-at-a-time implementation of Obara−Saika-type schemes in Libint for a variety of primitive and contracted integrals. As with our previous work, we rely on the standard C++ programming language such as the std::simd standard library feature to be included in the 2026 ISO C++ standard without any explicit code generation to keep the code base small and portable. The implementation is part of the open source LibintX library freely available at https://github.com/ValeevGroup/libintx.

Basis sets↗
DOE OSTI2026

A Simulator for Neyer Tests of Explosives

Explosives and explosive devices such as detonators are typically tested by applying a range of stimuli such as voltage or mechanical shock, and recording binary “detonated/did not detonate” responses. These are analyzed using maximum likelihood or generalized linear models to provide estimates of quantities such as the all-fire and no-fire points. Given that the true threshold for detonation is unknown a priori , sequential design methods are typically used to optimize the set of test points. One popular method, implemented in commercial software, is Neyer’s algorithm. To support simulation and experimental design, we have developed code in the R programming language to duplicate the functions of the Neyer software. We provide code for the simulator along with a description and examples of usage.

42 ENGINEERING↗
DOE OSTI2020

Matrix-free preconditioning for high-order H (curl) discretizations

The greater arithmetic intensity of high-order finite element discretizations makes them attractive for implementation on next-generation hardware, but assembly of high-order finite element operators as matrices is prohibitively expensive. As a result, the development of general algebraic solvers for such operators has been an open research challenge. Fast matrix-free application of high-order operators has received significant attention in the literature in the context of Poisson-type problems, but preconditioners and solvers for inverting more general operators are not very well-developed. In this paper, we consider the problem of preconditioning a definite Maxwell operator at high polynomial order without assembling a matrix. We show that given efficient preconditioners for high-order H 1 finite element problems on the same mesh, efficient H(curl) preconditioners can be constructed in an auxiliary space framework. We demonstrate the resulting preconditioners in a practical setting with tensor-product basis functions on an unstructured mesh of quadrilaterals. Overall, our approach uses a sparsified H 1 solver constructed on a low-order mesh of the nodal points of the underlying high-order space, and we show that the resulting H(curl) preconditioner is effective at very high polynomial orders for two-dimensional model problems with complicated geometry, varying piecewise constant coefficients, and curved elements. The resulting preconditioner scales with nearly optimal O(p d+1 ) floating point operation count and optimal O(p d ) memory transfer requirements, outperforming existing Maxwell preconditioners in the high-order regime.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Automatic inspection of program state in an uncooperative environment

Abstract The program state is formed by the values that the program manipulates. These values are stored in the stack, in the heap, or in static memory. The ability to inspect the program state is useful as a debugging or as a verification aid. Yet, there exists no general technique to insert inspection points in type‐unsafe languages such as C or C++. The difficulty comes from the need to traverse the memory graph in a so‐called uncooperative environment. In this article, we propose an automatic technique to deal with this problem. We introduce a static code transformation approach that inserts in a program the instrumentation necessary to report its internal state. Our technique has been implemented in LLVM. It is possible to adjust the granularity of inspection points trading precision for performance. In this article, we demonstrate how to use inspection points to debug compiler optimizations; to augment benchmarks with verification code; and to visualize data structures.

Magalhães, José Wesley de Souza↗
DOE OSTI2024

Advanced multimaterial shape optimization methods as applied to advanced manufacturing of wind turbine generators

Abstract Currently, many utility‐scale wind turbine generator original equipment manufacturers are dependent on imported rare earth permanent magnets, which are susceptible to market risks from cost instability. To lower the production costs of these generators and stay competitive in the market, several small wind manufacturers are pursuing continuous improvements to both generator design and manufacturing. However, traditional design and manufacturing methods have yielded marginal improvements in wind power performance. This work presents novel methods to redesign a baseline 15‐kW wind turbine generator with reduced rare‐earth permanent magnets by leveraging cutting‐edge three‐dimensional (3D) printed polymer‐bonded permanent magnets and steel. Symmetric, asymmetric, and multimaterial‐magnet parametrization methods are introduced for shape optimization. We extend the symmetric and asymmetric methods to the back iron in the stator to further investigate the impact and opportunities for performance improvements with lesser active materials. We employ a design‐of‐experiments approach with parametric computer‐aided design for shape generation and evaluate different designs by magneto‐thermal modeling and finite‐element analysis. We use adaptive sampling technique to identify better performing designs with lesser magnet mass, higher efficiency, and lower cogging torque when compared with the baseline generator. Asymmetric pole designs resulted in a magnet mass in the range of 4.77–5.37 kg, which was 27%–35% lighter than the baseline generator, suggesting that a new design freedom exists that can be enabled by advanced manufacturing, such as 3D printing. Shaping the back iron in the stator resulted in material savings in electrical steel of up to 14.62 kg, which was 20% lighter than the baseline stator. We conducted a structural analysis to evaluate an optimized asymmetric rotor design from the point of view of mechanical integrity and air‐gap stiffness. The magnetically optimal shape profile was shown as having a positive impact on the radial stiffness, and an optimal solution was discovered to reduce the structural mass by nearly 30 kg, which was 29% lighter than the baseline.

17 WIND ENERGY↗
DOE OSTI2025

Agrivoltaics as a climate-smart and resilient solution for midday depression in photosynthesis in dryland regions

Global projections of increased temperature and aridity have exacerbated concerns over our potential to achieve Sustainable Development Goals associated with food, energy, and water futures. We evaluated the implications of an agrivoltaics approach—combining agriculture and solar photovoltaics—on the microclimate growing conditions of crop species. While agrivoltaics is being explored globally for its potential to reduce soil evaporation rates and impact yield, empirical research on the mechanistic drivers of the potential for agrivoltaics is needed. Agrivoltaics mitigated the midday depression in photosynthesis experienced by crops grown in hot and arid environments, which led to reduced water stress, equal or greater daily carbon assimilation, and equal or greater yield across all crops. Our findings indicate agrivoltaics could be a climate-smart agricultural approach, and the diurnal resolution of our data points towards mechanisms for optimizing agrivoltaic designs to align with Sustainable Development Goals for food and energy production and water savings.

14 SOLAR ENERGY↗
DOE OSTI2023

Control of low-mode drive asymmetry in an efficient long-pulse low gas-fill density Hohlraum

Laser-driven Hohlraums filled with gas at lower densities (<0.6 mg/cc) have higher efficiency compared to original ≥ 0.96 mg/cc fill because of reduced backscatter losses [Hall et al., Phys. Plasmas 24, 052706 (2017)]. However, using low-density filled Hohlraums with longer drive required for lower adiabat implosions, and hence potentially higher inertial confinement fusion gain designs, has been challenging since the Hohlraum wall blow-off is less tamped, thus altering the laser beam absorption regions and drive symmetry. A series of NIF experiments using optimized pulse shaping, beam pointing, and temporal phasing have demonstrated, through imaging of the Hohlraum and capsule dynamics, that a symmetric implosion using a 14-ns low-adiabat drive pulse {2× longer than high-density-carbon ablator designs using low gas-fill density Hohlraums [Divol et al., Phys. Plasmas 24, 056309 (2017)]} is possible in a low backscatter loss 0.45 mg/cc He-filled Hohlraum. The ingress of the Hohlraum walls was mitigated by revisiting the adiabat-shaped design [Clark et al., Phys. Plasmas 21, 112705 (2014)] that uses a low-power (1 TW) trough that delays the wall expansion. Low-mode P 2 and P 4 drive asymmetry swings caused by the drift of the laser spots were essentially zeroed out by employing temporal beam phasing between cones of beams [Turner et al., Phys. Plasmas 7, 333 (2000)]. So the results also indicate an improved coupling efficiency of ~30% compared to an earlier design using higher density filled Hohlraums and pave the way for revisiting low-adiabat, high convergence drives using CH ablators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

𝜂 and 𝜂′ meson production in 𝐽/𝜓 radiative decays from lattice QCD

We report on the computation of amplitudes describing the radiative decay processes 𝐽/𝜓 →𝛾⁢𝜂 and 𝐽/𝜓 →𝛾⁢𝜂′ from first principles via lattice quantum chromodynamics (QCD). Using lattices with two heavier than physical degenerate flavors of light quark where 𝑚 𝜋 ∼391 MeV, and a strange quark tuned to approximately the physical value, we compute three-point correlation functions using optimized meson operators with a range of momenta. The use of optimized operators allows access to the 𝜂′, even though it appears as an excited state, lying above the ground-state 𝜂 in the isoscalar pseudoscalar channel. Statistically precise signals are obtained in this disconnected process by averaging over large numbers of kinematically equivalent correlators. We determine transition form factors as a function of photon virtuality across the timelike region, which describe also the Dalitz processes 𝐽/𝜓 →𝑒 + ⁢𝑒 − ⁢𝜂 (′) . Significantly lower magnitudes of transition form factor for both the 𝜂 and 𝜂′ are found than those extracted from experimental data, and possible explanations for this observation are presented.

form factors↗
DOE OSTI2022

Pairwise connected tensor network representation of path integrals

It has been recently shown how the tensorial nature of real-time path integrals (PIs) involving the Feynman-Vernon influence functional can be utilized with matrix product states, taking advantage of the finite length of the bath-induced memory. Tensor networks (TNs) promise to provide a unified language to express the structure of a PI. A generalized TN specifically incorporating the pairwise interaction structure of the influence functional and its invariance with respect to the average forward-backward position or the sojourn value in the form of the blip representation is derived and implemented. This pairwise connected TNPI (PC-TNPI) is illustrated through applications to typical spin-boson problems and explorations of the differences caused by the exact form of the spectral density. The storage and performance scalings are reported, showing the compactness of the representation and the efficiency of the contraction process. Finally, taking advantage of the compressed representation, the viability of using PC-TNPI for simulating multistate problems is demonstrated. The PC-TNPI structure can be shown to yield other TN algorithms currently in use. Consequently, it should be possible to use it as a starting point for deriving other optimized procedures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Indira: intent-based networking and rendering for networks (Indira) v1

Intelligent Network Deployment Intent Renderer Application an interactive network assistant that will help us configure a data path between two scientific end-point groups (EPGs) to optimize the transfer of elephant data flows. This tool is able to talk to scientists gather network requirements and then convert to network programming code and automate the end-to-end provisioning.

Pouyoul, Eric↗
DOE OSTI2023

pnnl/Pathway_Controlled_Optimization

A method for prediction of cell regulation to maximize cell growth rate while maintaining the solvent capacity of the cell. Prediction is formulated as an optimization problem using a thermodynamic framework that can leverage experimental data. We develop a formulation and variable initialization procedure that allows for computing solutions of the optimization with an interior point method

Central, PNNL Developer↗
DOE OSTI2022

Design Requirements and Software Specification for the Autonomous Energy Management Software System for Small Commercial Buildings

Commercial buildings are responsible for approximately 20 percent of the total United States energy consumption and greenhouse gas emissions. Over 85 percent of these buildings lack building automation systems. Many of these buildings are small (<50,000 square feet), underserved, and use rooftop units for heating, ventilation, and air-conditioning needs. Because these buildings lack proper energy management systems, they have several operational deficiencies that lead to excess energy consumption. Studies have shown that managing the rooftop units heating and cooling set points, schedules, setbacks, and optimal start can result in 20 to 25 percent reduction in electricity consumption in small commercial buildings. In addition, improving demand flexibility of these buildings will result additional cost savings for the building owner. Therefore, the Department of Energy’s Building Technologies Office approved a project to address the needs for small commercial buildings. The project is led by Pacific Northwest National Laboratory (PNNL) with Intellimation LLC as the cooperative research and development agreement partner. The primary goal of the project is to develop and validate an autonomous energy management software (AEMS) system that will continuously optimize small commercial building operations by minimizing energy consumption and cost, while providing a solution for maximizing decarbonization benefits from electrification of buildings. The work will leverage the vast experience of PNNL research and development staff who have over two decades of experience in developing and successfully transferring software technologies to the private sector. This solution will be jointly developed with Intellimation, a company that plans to use it to scale their building energy efficiency (EE) and grid services offering. Widespread deployment of the AEMS system will improve the EE and demand flexibility of the building commercial building stock. It should also support cities and states in meeting their climate change mitigation goals. This document describes the various EE and grid service features of the AEMS system, infrastructure and data required to implement those features, and how the features should be automated. It also details how the various features will be tested and validated, including field validation. The document also details what flexibility the users have and how they will be able to leverage those capabilities exercise those. The intent is to create an AEMS system that would support scalable deployment, requires minimal configuration, and is easy to maintain over its expected lifespan. The initial alpha release of AEMS system is planned for March 2023, and the beta release is planned for the summer of 2023. The final release is planned for March 2024. Section 2 of the report documents the relevant building types that AEMS is suitable for. Section 3 documents EE features that will be supported. It will also include the data requirements, hardware requirements, implementation details, and how EE features will be tested and validated. Grid service features will be documented in section 4, including data requirements, hardware requirements, implementation details, and how the services will be tested and validated. Planned next steps are described in section 5.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

An approach to learn regulation to maximize growth and entropy production rates in metabolism

Elucidating cell regulation remains a challenging task due to the complexity of metabolism and the difficulty of experimental measurements. Here we present a method for prediction of cell regulation to maximize cell growth rate while maintaining the solvent capacity of the cell. Prediction is formulated as an optimization problem using a thermodynamic framework that can leverage experimental data. We develop a formulation and variable initialization procedure that allows for computing solutions of the optimization with an interior point method. The approach is applied to photoheterotrophic growth of Rhodospirilium rubrum using ethanol as a carbon source, which has applications to biosynthesis of ethylene production. Growth is captured as the rate of synthesis of amino acids into proteins, and synthesis of nucleotide triphoshaptes into RNA and DNA. The method predicts regulation that produces a high rate of protein and RNA synthesis while DNA synthesis is reduced close to zero in agreement with production of DNA being turned off for much of the cell cycle.

59 BASIC BIOLOGICAL SCIENCES↗