Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Permittivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

NETL Plastic Pipes Project - June 2022 Progress Report

Plastic or composite pipelines have been the bane of the utility locating industry because conduits are neither conductive nor magnetic, which are the properties traditionally used to locate buried utilities. Ground penetrating radar (GPR) is an effective geophysical tool for locating plastic/composite pipeline where the resistive cover allows for adequate penetration of radar energy. However, GPR cannot be used in areas where the soil cover is conductive due to significant clay and/or salt content. This study takes a comprehensive look at near-surface geophysical methods that potentially are useful for locating buried plastic/composite pipelines, either singly or in combination with other geophysical methods. Specifically, this modeling study uses computational numerical methods to forward model the response of GPR, resistivity, seismic, and gravity gradiometry methods to plastic/composite pipelines for various scenarios including: (1) pipe diameters ranging between 2 in. to 12 in.; (2) burial depths ranging between 3 ft to 4 ft; (3) various degrees in contrast in physical properties (i.e., permittivity, elasticity, electrical resistivity, density); and (4) various experimental acquisition choices (e.g., GPR radar frequencies, seismic source frequency, electrode spacing).

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Exploration of a Novel Technique for Waste Heat Recovery Through Molecular Dynamics: Influence of Wettability and Electric Field on Water and Water-Based Nanofluids

Most of the energy produced globally comes by way of a heat engine. The Carnot principle places a limit as to how thermodynamically efficient a heat engine can be. There is no heat engine that can be 100% thermodynamically efficient and as such a substantial proportion of all heat supplied to a heat engine is lost as waste heat. Waste heat therefore is a large energy source ready to be properly utilized. Herein, a novel approach for converting waste heat to electricity is discussed. It involves the use of the liquid to vapor phase change of a material dielectric (water) or electrolyte (nanofluid) in the embodiment of a capacitor for direct thermal to electrostatic energy conversion. While this method of waste heat recovery could potentially be added to the ever expanding portfolio of energy conversion techniques, a number of aspects must be addressed before it can be brought into practice. Water was seen as an ideal dielectric phase change material given its high relative permittivity ratio when in the liquid form as compared to its vapor form. However, given its short voltage holdoff time the phase change of water would need to occur rapidly. This brings up concerns of explosive boiling. Herein, molecular dynamics analysis into the explosive boiling behavior of thin water films gave more insight into how the interaction between the surface and liquid affected explosive boiling onset time. A Lennard-Jones potential with one interaction site and a Morse potential with three interaction sites between water and solid substrate were used. It was found generally that a stronger interaction between water film and substrate led to faster explosive boiling onset times but an increase in the number of interaction sites delayed explosive boiling, even at the same wettability (contact angle). Understanding changes in the density and enthalpy of vaporization of a liquid dielectric such as water in the presence of an electric field is of importance due to the electrostatic nature of the waste heat conversion method under consideration. Specifically, if both density and enthalpy of vaporization are increased, the thermodynamic efficiency of the waste heat conversion method under consideration is decreased. Electric field effects are explored herein via molecular dynamics using two water models, the TIP4P-Ew and SWM4-NDP. The SWM4-NDP model is polarizable while the TIP4P-Ew model is not, which allows for a determination of the importance of model polarizability (i.e. variation in water model dipole moment) on these two properties of water when subjected to an electric field. Herein it was found that both water models respond similarly in terms of density and vaporization enthalpy variance upon the introduction of an electric field. Comparison was also made to the pressure induced by the electric field (electrostriction pressure) by way of a density comparison and it was found that the predicted electrostriction pressure overestimates the pressure experienced by water. Water by itself has a high enthalpy of vaporization, which limits the efficiency of the newly proposed conversion method. Research both experimental and through simulation has shown that the vaporization enthalpy of nanofluids can be engineered via nanoparticle size and material selection. An avenue less explored is manipulating the enthalpy of vaporization by altering the interaction strength between the nanoparticles and the base fluid. In practice this could be achieved through the addition of coatings to the nanoparticles to alter their wettability to the base fluid. This was explored by using a Lennard-Jones potential and Morse potential to model the interaction between base fluid (water) and the nanoparticle. For nanoparticles 2nm in diameter and at weight percentages up to 6%, the change in vaporization enthalpy due to alterations of the interaction strength between nanoparticle and base fluid was not significant (less than a 1% difference) when compared to the effect of altering the weight percentage of nanoparticles in the nanofluid or introducing an electric field. However, the effect of wettability may still become important at other nanoparticle concentrations and sizes. In all, the studies presented here further the understanding of phase change and thermodynamic properties of water and water based nanofluids under an electrostatic field which will help inform the development of a novel approach to waste heat conversion. The reduction of waste heat will improve energy sustainability outlooks.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Power Dissipation on the Metallic Coating of a Ceramic Chamber in Planar Approximation

We adopt the standard field matching technique to solve the general electromagnetic problem consisting of two parallel layers with arbitrary complex relative permittivity and permeability. With parameters of the NSLS-II ceramic chambers, we calculate the power dissipated on the metallic coating and compare the result with the power lost by the beam and with the results of [4].

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Tomographic optical emission spectroscopy of atmospheric pressure plasma interacting with complex surfaces

Plasma distribution in 3D space is heavily influenced by complex surfaces and the coupling interactions between plasma properties and interfacing material properties. For example, guided streamers that transition to surface ionization waves (SIWs) and propagate over structured dielectrics experience field enhancements that can lead to localized increases in ionization rates and complex 3D configurations that are difficult to analyze. Investigating these configurations requires techniques than can provide a more complete 3D picture. To help address this capability gap, a tomographic optical emission spectroscopy (tomo-OES) diagnostic system has been developed at Sandia National Laboratories that can resolve SIWs. The system includes four intensified cameras that measure the angular projections of the plasma light emission through bandpass filters. A dot calibration target co-registers each angular projection to the same voxel grid and an algebraic reconstruction technique (ART) recovers the light intensity at each voxel. An atmospheric pressure plasma jet (APPJ), provided by Peter Bruggeman, has been investigated and representative results are shown in Figure 1. Here, a bandpass filter was used to isolate emission from the N 2 second positive system (SPS) at 337.1 nm to capture the transition of the streamer to SIW on a planar dielectric surface (relative permittivity 3.3) located 3 mm below the APPJ [3]. The surface wave velocity was 3.5x10 4 (m/s), consistent with measurements made by Steven Shannon. Characterization of this APPJ will support the group effort of standing up a reproducible APPJ across institutions for applications such as liquid treatment, catalysis, and plasma aided combustion. Future work will investigate non-planar surfaces and eventually develop tomographic laser-induced fluorescence (tomo-LIF) approaches.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Development of electro-optical quantum transducers based on three-dimensional superconducting cavities

Quantum transducers enable the conversion of quantum information and signals between different physical platforms. Based on the pioneering works in three-dimensional superconducting cavity technology developed at Fermilab, we are advancing the development of three-dimensional microwave-optical transducers and exploring their applications in quantum information processing and sensing. We present our progress in the design, fabrication, and characterization of three-dimensional microwave cavities integrated with bulk lithium niobate resonators. The material characterization using three-dimensional cavities based on a resonant-type method allows for understanding of complex permittivity and loss mechanism of electro-optic materials at cryogenic temperatures. We also evaluate the potential of the high-efficiency quantum transducers in enhancing the performance of quantum sensors for applications such as dark matter detection, compared to conventional homodyne detection approaches. This manuscript has been authored by Fermi Research Alliance, LLC under Contract No. DE-AC0207CH11359 with the U.S. Department of Energy, Office of Science, Office of High Energy Physics. This work is funded by the DOE's Early Career Research Program. This research used resources of the U.S. Department of Energy, Office of Science, National Quantum Information Science Research Centers, Superconducting Quantum Materials and Systems Center (SQMS) under Contract No. DE-AC02-07CH11359.

Zorzetti, Silvia↗
DOE OSTI2024

The mechanical properties of Kel-F 800 (FK-800) as a function of crystallinity

Kel-F 800 is a copolymer of chlorotrifluoroethylene PTFE (75 wt. %) and vinylidene fluoride PVDF (25 wt. %). It has previously been used as a PBX binder for insensitive explosives such as PBX 9502 and LX-17. 3M started production of Kel-F 800 in 1957 and small-scale batches continued to be made until 2002 when production ceased due to environmental concerns regarding one of the emulsifiers used during production. Around 2000 the Kel-F 800 name was changed to FK-800 to avoid trademark concerns because rights to produce another polymer with a similar tradename (Kel-F 81) had been sold to another manufacturer. The Kel designation came from the original manufacturer of PCTFE (Kel-F 81), the Kellog company. To avoid confusion this document will only refer to Kel-F 800. In 2006, production of small-scale batches of Kel-F 800 was started again by 3M in response to customer enquiries. This new material, the first blended batch is referred to as LOT 1, was produced with a different emulsifier than used previously. Because Kel-F 800 is made in a small batch reactor, considerable variation in crystallinity can be expected from lot to lot and year to year. In many ways, this is not significant since the material is dissolved in a solvent (often MEK, ethylmethyl ketone or ethyl acetate) for PBX production purposes. This destroys the as received crystallinity and the resulting crystallinity in the processed material is a function of polymer molecular weight and thermal history. Producing large billets of Kel-F 800 from solvent extraction is not practical and so a compression molding technique has been used above the melting temperature. This method also removes residual crystallinity from the supplied granules. The molecular weight of a polymer can be estimated by several techniques, the most common being gel permittivity chromatography (GPC), size exclusion chromatography (SEC) and shear rheometry measurements of polymer/solvent solutions. Changes in molecular weight will affect the crystallization rate and the maximum crystallinity reached for a specific thermal history. Both references agree that the new LOT 1 material molecular weight falls within the deviation found from averaging previous historical lots of Kel-F 800.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Broad Frequency Shift of Parametric Processes in Epsilon-Near-Zero Time-Varying Media

The ultrafast changes of material properties induced by short laser pulses can lead to a frequency shift of reflected and transmitted radiation. Recent reports highlight how such a frequency shift is enhanced in spectral regions where the material features a near-zero real part of the permittivity. Here, we investigate the frequency shift for fields generated by four-wave mixing. In our experiment, we observed a frequency shift of more than 60 nm (compared to the pulse width of ~40 nm) in the phase conjugated radiation generated by a 500 nm aluminium-doped zinc oxide (AZO) film pumped close to the epsilon-near-zero wavelength. Our results indicate applications of time-varying media for nonlinear optics and frequency conversion.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Flexible Magnetic Polymer Composite Substrate with Ba 1.5 Sr 1.5 Z Hexaferrite Particles of VHF/Low UHF Patch Antennas for UAVs and Medical Implant Devices

Our goal is to fabricate flexible magnetic polymer composites as antenna substrates for very high frequency (VHF)/low ultra high frequency (UHF) antennas for unmanned aerial vehicles (UAVs) and medical devices. Magnetodielectric materials, which have permeability (μ) similar to permittivity (ε), have attracted great attention, because they facilitate miniaturization of microwave devices while keeping or enhancing electromagnetic characteristics. Mechanically millled Ba 1.5 Sr 1.5 Co 2 Fe 24 O 41 (Ba 1.5 Sr 1.5 Z) hexaferrite particles were used to increase permeability in the interesting frequency band. The microwave properties of Ba 1.5 Sr 1.5 Z composites were predicted and measured. Hansen’s zero-order analysis of antenna bandwidth and electromagnetic field simulation showed that the hexaferrite-based flexible composite could enhance a bandwidth and achieve the miniaturization of antennas as well. The magnetic antenna substrates can be a good solution to integrate antennas into the UAVs whose dimensions are comparable to or larger than communication wavelength.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Vertical and Lateral Etch Survey of Ferroelectric AlN/Al 1-x Sc x N in Aqueous KOH Solutions

Due to their favorable electromechanical properties, such as high sound velocity, low dielectric permittivity and high electromechanical coupling, Aluminum Nitride (AlN) and Aluminum Scandium Nitride (Al 1-x Sc x N) thin films have achieved widespread application in radio frequency (RF) acoustic devices. The resistance to etching at high scandium alloying, however, has inhibited the realization of devices able to exploit the highest electromechanical coupling coefficients. In this work, we investigated the vertical and lateral etch rates of sputtered AlN and Al 1-x Sc x N with Sc concentration x ranging from 0 to 0.42 in aqueous potassium hydroxide (KOH). Etch rates and the sidewall angles were reported at different temperatures and KOH concentrations. We found that the trends of the etch rate were unanimous: while the vertical etch rate decreases with increasing Sc alloying, the lateral etch rate exhibits a V-shaped transition with a minimum etch rate at x = 0.125. By performing an etch on an 800 nm thick Al 0.875 Sc 0.125 N film with 10 wt% KOH at 65 °C for 20 min, a vertical sidewall was formed by exploiting the ratio of the {$10\overline{11}$ planes and {$1\overline{1}00$ planes etch rates. This method does not require preliminary processing and is potentially beneficial for the fabrication of lamb wave resonators (LWRs) or other microelectromechanical systems (MEMS) structures, laser mirrors and Ultraviolet Light-Emitting Diodes (UV-LEDs). It was demonstrated that the sidewall angle tracks the trajectory that follows the {$\overline{1}2\overline{12}$ of the hexagonal crystal structure when different c/a ratios were considered for elevated Sc alloying levels, which may be used as a convenient tool for structure/composition analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

ZnO-Au x Cu 1-x Alloy and ZnO-Au x Al 1-x Alloy Vertically Aligned Nanocomposites for Low-Loss Plasmonic Metamaterials

Hyperbolic metamaterials are a class of materials exhibiting anisotropic dielectric function owing to the morphology of the nanostructures. In these structures, one direction behaves as a metal, and the orthogonal direction behaves as a dielectric material. Applications include subdiffraction imaging and hyperlenses. However, key limiting factors include energy losses of noble metals and challenging fabrication methods. In this work, self-assembled plasmonic metamaterials consisting of anisotropic nanoalloy pillars embedded into the ZnO matrix are developed using a seed-layer approach. Alloys of Au x Al 1-x or Au x Cu 1-x are explored due to their lower losses and higher stability. Optical and microstructural properties were explored. The ZnO-Au x Cu 1-x system demonstrated excellent epitaxial quality and optical properties compared with the ZnO-Au x Al 1-x system. Both nanocomposite systems demonstrate plasmonic resonance, hyperbolic dispersion, low losses, and epsilon-near-zero permittivity, making them promising candidates towards direct photonic integration.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Epitaxial Stabilization of Single-Crystal Multiferroic YCrO 3 Thin Films

We report on the growth of stoichiometric, single-crystal YCrO 3 epitaxial thin films on (001) SrTiO 3 substrates using pulsed laser deposition. X-ray diffraction and atomic force microscopy reveal that the films grew in a layer-by-layer fashion with excellent crystallinity and atomically smooth surfaces. Magnetization measurements demonstrate that the material is ferromagnetic below 144 K. The temperature dependence of dielectric permittivity shows a characteristic relaxor-ferroelectric behavior at T C = 375–408 K. A dielectric anomaly at the magnetic transition temperature indicates a close correlation between magnetic and electric order parameters in these multiferroic YCrO 3 films. These findings provide guidance to synthesize rare-earth, chromite-based multifunctional heterostructures and build a foundation for future studies on the understanding of magnetoelectric effects in similar material systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Vertical Etching of Scandium Aluminum Nitride Thin Films Using TMAH Solution

A wide bandgap, an enhanced piezoelectric coefficient, and low dielectric permittivity are some of the outstanding properties that have made Sc x Al 1-x N a promising material in numerous MEMS and optoelectronics applications. One of the substantial challenges of fabricating Sc x Al 1-x N devices is its difficulty in etching, specifically with higher scandium concentration. In this work, we have developed an experimental approach with high temperature annealing followed by a wet etching process using tetramethyl ammonium hydroxide (TMAH), which maintains etching uniformity across various Sc compositions. The experimental results of etching approximately 730 nm of Sc x Al 1-x N (x = 0.125, 0.20, 0.40) thin films show that the etch rate decreases with increasing scandium content. Nevertheless, sidewall verticality of 85°~90° (±0.2°) was maintained for all Sc compositions. Based on these experimental outcomes, it is anticipated that this etching procedure will be advantageous in the fabrication of acoustic, photonic, and piezoelectric devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Threshold Helium Leakage Detection Switch with Ultra Low Power Operation

Detecting helium leakage is important in many applications, such as in dry cask nuclear waste storage systems. This work develops a helium detection system based on the relative permittivity (dielectric constant) difference between air and helium. This difference changes the status of an electrostatic microelectromechanical system (MEMS) switch. The switch is a capacitive-based device and requires a very negligible amount of power. Exciting the switch’s electrical resonance enhances the MEMS switch sensitivity to detect low helium concentration. This work simulates two different MEMS switch configurations: a cantilever-based MEMS modeled as a single-degree-freedom model and a clamped-clamped beam MEMS molded using the COMSOL Multiphysics finite-element software. While both configurations demonstrate the switch’s simple operation concept, the clamped-clamped beam was selected for detailed parametric characterization due to its comprehensive modeling approach. The beam detects at least 5% helium concentration levels when excited at 3.8 MHz, near electrical resonance. The switch performance decreases at lower excitation frequencies or increases the circuit resistance. The MEMS sensor detection level was relatively immune to beam thickness and parasitic capacitance changes. However, higher parasitic capacitance increases the switch’s susceptibility to errors, fluctuations, and uncertainties.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Active Layer and Moisture Measurements for Intensive Site 0 and 1, Utqiagvik (Barrow), Alaska

Thaw depth, relative dielectric permittivity, and soil temperature were collected along three transects within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) near Utqiagvik (Barrow), Alaska. Measurements were acquired along the transect at 3 m intervals on 2011-09-25, 2011-09-26, 2012-07-18, 2012-09-30, 2014-07-02, 2014-08-15, and 2014-09-14 for the L2 transect (intensive site 0), which is about 470 m long. Similarly, measurements were collected every 3 m on 2012-09-30, 2013-09-30, 2014-07-02, 2014-08-14, and 2014-09-23, and every 1 m on 2013-09-30 along the AB transect (intensive site 1) which is about 500 m long. File types in the package are all csv spreadsheets, following the ESS-DIVE csv guidelines (ESS-DIVE CSV v1), organized by transect name, with accompanying data dictionary files containing the filename suffix "_dd" (also csv format). Data collection details can be found in the Methods description of the metadata record. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Scattering of Radio Frequency Waves by Density Filaments

The edge region and the scrape-off layer of magnetically confined fusion devices, like tokamaks and stellarators, are replete with turbulent plasma that is a mixture of coherent, blob or filament like, structures [1] and incoherent fluctuations [2]. The variation in the density due to turbulence can be comparable to or greater than the ambient density [2]. As part of an overall effort to optimize the efficiency of operation, radio frequency (RF) waves are commonly used for heating fusion plasmas and, in tokamaks, for generating plasma current needed for confinement and controlling instabilities. The RF waves are excited by antenna structures that are placed near the wall of a fusion device. In order to deliver energy and momentum to charged particles in the core of fusion plasmas, RF waves have to propagate through the turbulent plasma. In present fusion devices, the scrap-off layer and the edge plasma region is of the order of a few centimeters. In reactor type devices, like ITER, this region is expected to be of the order of tens of centimeters. Since the efficiency of operation of a fusion reactor is of prime importance, it is imperative that we understand the effect of turbulence on RF waves. The fluctuations in density lead to changes in the plasma permittivity. As in conventional electrodynamics, the propagation of RF waves through different dielectric media is subject to reflection, refraction, and diffraction. In this paper, we summarize our theoretical and computational studies on the propagation of RF waves through filamentary structures present in the scrape-off layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Interaction of radio frequency waves with cylindrical density filaments -- scattering and radiation pressure

The propagation of radio-frequency (RF) waves in tokamaks can be affected by filamentary structures, or blobs, that are present in the edge plasma and the scrape-off layer. The difference in the permittivity between the surrounding plasma and interior of a filament leads to reflection, refraction and diffraction of the waves. This, in turn, can affect the power flow into the core of the plasma and reduce the efficiency of heating and/or current generation. The scattering of RF waves, lower hybrid, helicon and ion cyclotron waves, by a single cylindrical filament, embedded in a background plasma, is studied using a full-wave analytical theory developed previously (Ram & Hizanidis, Phys. Plasmas, vol. 23, 2016, 022504). The theory assumes that the plasma in and around a filament is homogeneous and cold. A detailed scattering analysis reveals a variety of common features that exist among the three distinctly different RF waves. These common attributes can be inferred intuitively based on an examination of the cold plasma dispersion relation. The physical intuition is a useful step to understanding experimental observations on scattering, as well as results from simulations that include general forms of edge plasma turbulence. While a filament can affect the propagation of RF waves, the radiation force exerted by the waves can influence the filament. The force on a filament is determined using the Maxwell stress tensor. In 1905, Poynting was the first to evaluate and measure the radiation force on an interface separating two different dielectric media (Poynting, London Edinburgh Dublin Philos. Mag. J. Sci., vol. 9, 1905, pp. 393–406). For ordinary light propagating in vacuum and incident on a glass surface, Poynting noted that the surface is ‘pulled’ towards the vacuum. In a magnetized cold plasma, there are two independent wave modes. Even if only one of these modes is excited by an RF antenna, a filament will couple power to the other mode: a consequence of electromagnetic boundary conditions. This facet of scattering has consequences on the radiation force that go beyond Poynting's seminal contribution. The direction of the force depends on the polarization of the incident wave and on the mode structure of the waves inside and in the vicinity of a filament. It can either pull the filament toward the RF source or push it away. For slow lower hybrid waves, filaments with densities greater than the ambient density are pulled in, while filaments with lower densities are pushed out, thereby enhancing the density in front of the antenna. In the case of fast helicon and ion cyclotron waves, the direction of the force depends on the plasma and wave parameters; in particular, on the ambient density. The radiation force, in all three frequency ranges, is large enough to affect the motion of a filament and could be measured experimentally. This also suggests the possibility of modifying the edge turbulence using RF waves.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Diffraction of radio-frequency waves by plasma turbulence in the edge of a tokamak

The Mie-Lorenz-Debye theory of scattering of radio frequency waves (RF) by filamentary structures in the edge of a tokamak plasma has been established in prior publications. These results have been verified. Theory and computations show that RF can be reflected, refracted, and diffracted by turbulence. Furthermore, the filamentary structures lead to side scattering of waves and excitation of wave modes different from the launched RF. It is important to quantify the overall effect of turbulence on the propagation of RF since efficiency of heating and current drive by RF waves depends upon the wave characteristics. The commonly used RF ranges vary from the low frequency ion-cyclotron (IC) waves, to medium frequency lower-hybrid (LH) waves, to high-frequency electron cyclotron (EC) waves with wavelengths respectively, large, comparable, or smaller than the radial dimensions of the filaments. Currently, we discuss the scattering as well as the forces exerted by different RF in the edge plasma. Also, we present a code for 3D full wave scattering analysis of arbitrary tensor permittivity and plasma density profiles. The study is applicable to ITER-like plasmas, as well as to plasmas in medium sized tokamaks such as TCV, ASDEX-U and DIII-D and high field concepts like SPARC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Scattering of lower hybrid radio frequency waves by cylindrical turbulent structures in the plasma edge in tokamaks

Lower hybrid (LH) radio frequency (RF) waves are used in fusion tokamak devices to generate non-inductively toroidal currents. LH waves are effective in imparting toroidal momentum to electrons in the core of the confined plasma. Since the LH waves are generated by wave guide structures near the wall of a tokamak, the waves have to propagate through a turbulent plasma in the edge region before coupling to the core. It is especially important to quantify the effect of this plasma region on the propagation characteristics of the LH waves, since fusion reactors like ITER will have an extended edge region. Structures in the plasma edge like filaments and blobs which have highly varying density fluctuations compared to the background density, span radial spatial scales that are comparable to the LH wavelength. We study the scattering of the LH waves by the filamentary structures using Maxwell's equations, in which the plasma permittivity is given by the cold plasma dispersion tensor. The collisional absorption of LH waves in the edge region is included by a modification to the elements of the dispersion tensor. The filaments are assumed to be cylindrical with the axis predominantly aligned along the direction of the toroidal magnetic field. Our studies are both analytical and numerical [1,2] and show that these structures can lead to reflection, refraction, diffraction, and side-scattering of both an incident LH plane wave and a Gaussian beam. We will present a variety of different density variations and collisional absorption rates in plasmas with filamentary structures of varying sizes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗