Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Patterning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Measuring residual stress in Ti-6Al-4V with HR-EBSD, using reference patterns from annealed material

In this study, elastic strain and residual stress values in an engineering material were determined by high-resolution EBSD (HR-EBSD) using reference patterns from annealed, recrystallized material. Specifically, rolled Ti-6Al-4V sheet was analyzed using HR EBSD in both an as-annealed and a strained state, the latter established via a static two-point bend fixture. The commercial software CrossCourt4 (CC4) was used to evaluate the relative intragranular strain tensor components of the alpha grains mapped by HR-EBSD. The intragranular reference patterns identified in each grain by the software were then replaced with similarly-oriented patterns from scans of the as-annealed, recrystallized material. The CC4 analysis was then repeated to provide calibrated strain and residual stress values. Elastic strains on the order of 10–3 were detected, with corresponding residual stress values on the order of 1 GPa. Subsequent analyses using high energy synchrotron x-ray diffraction showed good correlation with the elastic strains measured by HR-EBSD using the annealed reference patterns. Additionally, the maximum macroscopic stress analytically predicted for two-point bending was in agreement with the residual stress observed. Good repeatability of the methodology and insight into the state of individual grains were also observed. The findings provide encouraging evidence that accurate intragranular and long-range residual stress measurements of engineering significance can be made with HR-EBSD using a physical reference pattern library.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Denoising Autoencoder for Improved Kikuchi Pattern Quality and Indexing in Electron Backscatter Diffraction

The rapid collection and indexing of electron diffraction patterns as produced via electron backscatter diffraction (EBSD) has enabled crystallographic orientation and structural determination, as well as additional property-determining strain and dislocation density information with increasing speed, resolution, and efficiency. Pattern indexing quality is reliant on the noise of the collected electron diffraction patterns, which is often convoluted by sample preparation and data collection parameters. EBSD acquisition is sensitive to many factors and thus can result in low confidence index (CI), poor image quality (IQ), and improper minimization of fit, which can result in noisy datasets and misrepresent the microstructure. In an attempt to enable both higher speed EBSD data collection and enable greater orientation fit accuracy with noisy datasets, an image denoising autoencoder was implemented to improve pattern quality. Here, we show that EBSD data processed through the autoencoder results in a higher CI, IQ, and a more accurate degree of fit. In addition, using denoised datasets in HR-EBSD cross correlative strain analysis can result in reduced phantom strain from erroneous calculations due to the increased indexing accuracy and improved correspondence between collected and simulated patterns.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Using Knowledge-Guided Machine Learning To Assess Patterns of Areal Change in Waterbodies across the Contiguous United States

Lake and reservoir surface areas are an important proxy for freshwater availability. Advancements in machine learning (ML) techniques and increased accessibility of remote sensing data products have enabled the analysis of waterbody surface area dynamics on broad spatial scales. However, interpreting the ML results remains a challenge. While ML provides important tools for identifying patterns, the resultant models do not include mechanisms. Thus, the “black-box” nature of ML techniques often lacks ecological meaning. Using ML, we characterized temporal patterns in lake and reservoir surface area change from 1984 to 2016 for 103,930 waterbodies in the contiguous United States. We then employed knowledge-guided machine learning (KGML) to classify all waterbodies into seven ecologically interpretable groups representing distinct patterns of surface area change over time. Many waterbodies were classified as having “no change” (43%), whereas the remaining 57% of waterbodies fell into other groups representing both linear and nonlinear patterns. This analysis demonstrates the potential of KGML not only for identifying ecologically relevant patterns of change across time but also for unraveling complex processes that underpin those changes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Laser Scribing for Electrode Patterning of Perovskite Spectrometer-Grade CsPbBr 3 Gamma-ray Detectors

Making semiconductor radiation detectors that work at room temperature relies heavily on the deposition and pixelation of electrodes. Electrode patterning of perovskite solar cells widely implements laser scribing techniques, which is a convenient, scalable, and inexpensive technique. However, this method has not found its application in radiation detector patterning yet, and the question whether laser scribing can achieve high-quality patterns with minimum damage to a detector crystal and low interpixel cross-talk remains largely unanswered. To prove that laser scribing is a practical method for electrode patterning on perovskite CsPbBr 3 detectors, we use the material to create a variety of patterns. A very low lateral leakage current (60 nA at 10 V) and high mobility-lifetime product (9.7(3) x 10 -4 cm 2 /V) were observed between the pixel and the guard ring in tests of single-pixel devices with a separation of 200 or 100 μm between the central electrode and the guard ring. The 122 and 136 keV photopeaks in 57 Co gamma-ray spectra were very well resolved with an energy resolution of up to 6.1% at 122 keV. Finally, a further reduction in gap size to 50 mu m is conceivable, but more process optimization is needed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Indicator Patterns of Forced Change Learned by an Artificial Neural Network

Abstract Many problems in climate science require the identification of signals obscured by both the “noise” of internal climate variability and differences across models. Following previous work, we train an artificial neural network (ANN) to predict the year of a given map of annual‐mean temperature (or precipitation) from forced climate model simulations. This prediction task requires the ANN to learn forced patterns of change amidst a background of climate noise and model differences. We then apply a neural network visualization technique (layerwise relevance propagation) to visualize the spatial patterns that lead the ANN to successfully predict the year. These spatial patterns thus serve as “reliable indicators” of the forced change. The architecture of the ANN is chosen such that these indicators vary in time, thus capturing the evolving nature of regional signals of change. Results are compared to those of more standard approaches like signal‐to‐noise ratios and multilinear regression in order to gain intuition about the reliable indicators identified by the ANN. We then apply an additional visualization tool (backward optimization) to highlight where disagreements in simulated and observed patterns of change are most important for the prediction of the year. This work demonstrates that ANNs and their visualization tools make a powerful pair for extracting climate patterns of forced change.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Connecting Large‐Scale Meteorological Patterns to Extratropical Cyclones in CMIP6 Climate Models Using Self‐Organizing Maps

Abstract Extratropical cyclones (ETCs) are responsible for the majority of cool‐season extreme events in the northeastern United States (NEUS), often leading to high‐impact weather conditions that can have wide‐ranging socioeconomic impacts. Evaluating the ability of climate models to adequately simulate ETC dynamics is essential for improving model performance and increasing confidence in future projections used by stakeholders and policymakers. ETCs are traditionally studied using techniques such as case studies and synoptic typing, however, these approaches can be time‐consuming, require subjective analysis, and do not necessarily identify the coincident large‐scale meteorological patterns (LSMPs). Here, we apply self‐organizing maps (SOMs) as an automated machine‐learning approach to characterize the LSMPs and associated frequency and intensity of discrete ETC events over NEUS. The dominant patterns of geopotential height variability are identified through SOM analysis of five reanalysis products during the last four decades. ETC events are tracked using TempestExtremes and are integrated with SOMs to classify the accumulated cyclone activity (ACA) associated with each pattern. We then evaluate the skill of CMIP6 historical experiments in simulating the LSMPs and ETC events identified in the SOM. Our results identify a robust bias toward more zonal patterns, with models struggling to reproduce the more amplified patterns typically associated with the highest cyclone activity. While model resolution has some impact on simulation credibility, model configuration appears to be more important in LSMP representation. The vast majority of CMIP6 models produce too few ETCs, although model errors are distributed around historical reanalyses when ACA is normalized by storm frequency.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Understanding the Influence of Urban Form on the Spatial Pattern of Precipitation

Urban areas are known to modify the spatial pattern of precipitation climatology. Existing observational evidence suggests that precipitation can be enhanced downwind of a city. Among the proposed mechanisms, the thermodynamic and aerodynamic processes in the urban lower atmosphere interact with the meteorological conditions and can play a key role in determining the resulting precipitation patterns. In addition, these processes are influenced by urban form, such as the impervious surface extent. This study aims to unravel how different urban forms impact the spatial patterns of precipitation climatology under different meteorological conditions. We use the Multi-Radar Multi-Sensor quantitative precipitation estimation data products and analyze the hourly precipitation maps for 27 selected cities across the continental United States from the years 2015–2021 summer months. Results show that about 80% of the studied cities exhibit a statistically significant downwind enhancement of precipitation. Additionally, we find that the precipitation pattern tends to be more spatially clustered in intensity under higher wind speed; the location of radial precipitation maxima is located closer to the city center under low background winds but shifts downwind under high wind conditions. The magnitude of downwind precipitation enhancement is highly dependent on wind directions and is positively correlated with the city size for the south, southwest, and west directions. This study presents observational evidence through a cross-city analysis that the urban precipitation pattern can be influenced by the urban modification of atmospheric processes, providing insight into the mechanistic link between future urban land-use change and hydroclimates.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Snow Distribution Patterns Revisited: A Physics-Based and Machine Learning Hybrid Approach to Snow Distribution Mapping in the Sub-Arctic

Snowpack distribution in Arctic and alpine landscapes often occurs in repeating, year-to-year patterns due to local topographic, weather, and vegetation characteristics. Previous studies have suggested that with years of observational data, these snow distribution patterns can be statistically integrated into a snow process modeling workflow. Recent advances in snow hydrology and machine learning (ML) have increased our ability to predict snowpack distribution using in-situ observations, remote sensing data sets, and simple landscape characteristics that can be easily obtained for most environments. Here, we propose a hybrid approach to couple a ML snow distribution pattern (MLSDP) map with a physics-based, snow process model. We trained a random forest ML algorithm on tens of thousands of snow survey observations from a subarctic study area on the Seward Peninsula, Alaska, collected during peak snow water equivalent (SWE). We validated hybrid model outputs using in-situ snow depth and SWE observations, as well as a light detection and ranging data set and a distributed temperature profiling sensor data set. When the hybrid results were compared with the physics-based method, the hybrid method more accurately depicted the spatial patterns of the snowpack, areas of drifting snow, and years when no in-situ observations were used in the random forest ML training data set. The hybrid method also showed improvements in root mean squared error at 61% of locations where time-series estimations of snow depth were observed. These results can be applied to any physics-based model to improve the snow distribution patterning to reflect observed conditions in high latitude and high elevation cold region environments.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Optimizing HAARP Beam Pattern for Generation of Strong F‐Region Field‐Aligned Irregularities

Field-aligned irregularities (FAIs) are the signatures of plasma turbulence and convection in the mid- and high-latitude F-region ionosphere, and also provide coherent backscatter targets for HF radars. To serve irregularity generation and characterization studies, we conducted experiments at the High-frequency Active Auroral Research Program (HAARP) in August 2023 with the goal of identifying the optimal HAARP beam pattern for reliable generation of intense FAIs over a large geographic region. The HAARP beam patterns we tested were the commonly-used narrow beam, also known as L0, as well as the wider L1 and L2 “twisted” beam patterns. The size and intensity of the FAI region generated by each HAARP beam pattern was quantified using the Kodiak Island Super Dual Auroral Radar Network (SuperDARN) radar. Stimulated electromagnetic emissions (SEE) from heater wave-FAI scattering were also recorded using a receiver located near HAARP. The L1 beam pattern was found to produce the strongest SuperDARN backscatter over the largest region. Although the heater frequency was intended to be tuned a few hundred kHz below the F-region critical frequency (foF2) during each experiment, difficulty in estimating foF2 during the campaign likely resulted in HAARP heating at significantly different frequency ranges around foF2 during each experiment. Although this additional free parameter complicated data analysis for this study, the SuperDARN and SEE measurements have led to further inquiry into the role heater frequency plays in the artificial generation of FAIs.

58 GEOSCIENCES↗
DOE OSTI2021

Foundry-compatible high-resolution patterning of vertically phase-separated semiconducting films for ultraflexible organic electronics

Solution processability of polymer semiconductors becomes an unfavorable factor during the fabrication of pixelated films since the underlying layer is vulnerable to subsequent solvent exposure. A foundry-compatible patterning process must meet requirements including high-throughput and high-resolution patternability, broad generality, ambient processability, environmentally benign solvents, and, minimal device performance degradation. However, known methodologies can only meet very few of these requirements. Here, a facile photolithographic approach is demonstrated for foundry-compatible high-resolution patterning of known p- and n-type semiconducting polymers. This process involves crosslinking a vertically phase-separated blend of the semiconducting polymer and a UV photocurable additive, and enables ambient processable photopatterning at resolutions as high as 0.5 μm in only three steps with environmentally benign solvents. The patterned semiconducting films can be integrated into thin-film transistors having excellent transport characteristics, low off-currents, and high thermal (up to 175 °C) and chemical (24 h immersion in chloroform) stability. Moreover, these patterned organic structures can also be integrated on 1.5 μm-thick parylene substrates to yield highly flexible (1 mm radius) and mechanically robust (5,000 bending cycles) thin-film transistors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Integrated analysis of X-ray diffraction patterns and pair distribution functions for machine-learned phase identification

Abstract To bolster the accuracy of existing methods for automated phase identification from X-ray diffraction (XRD) patterns, we introduce a machine learning approach that uses a dual representation whereby XRD patterns are augmented with simulated pair distribution functions (PDFs). A convolutional neural network is trained directly on XRD patterns calculated using physics-informed data augmentation, which accounts for experimental artifacts such as lattice strain and crystallographic texture. A second network is trained on PDFs generated via Fourier transform of the augmented XRD patterns. At inference, these networks classify unknown samples by aggregating their predictions in a confidence-weighted sum. We show that such an integrated approach to phase identification provides enhanced accuracy by leveraging the benefits of each model’s input representation. Whereas networks trained on XRD patterns provide a reciprocal space representation and can effectively distinguish large diffraction peaks in multi-phase samples, networks trained on PDFs provide a real space representation and perform better when peaks with low intensity become important. These findings underscore the importance of using diverse input representations for machine learning models in materials science and point to new avenues for automating multi-modal characterization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nanoscale Turing patterns in a bismuth monolayer

Turing’s reaction–diffusion theory of morphogenesis has been very successful for understanding macroscopic patterns within complex objects ranging from biological systems to sand dunes. However, Turing patterns on microscopic length scales are extremely rare. Here we show that a strained atomic bismuth monolayer assembled on the surface of NbSe 2 —and subject to interatomic interactions and kinetics—displays Turing patterns. Our reaction–diffusion model produces stripe patterns with a period of five atoms (approximately 2 nm) and domain walls with Y-shaped junctions that bear a striking resemblance to what has been experimentally observed. Our work establishes that Turing patterns can occur at the atomic scale in a hard condensed-matter setting.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The fate of liquid crystal topological defects on chemically patterned surfaces during phase transitions

Controlling topological defects in liquid crystals (LCs) is an essential element in the development of areas such as directed self-assembly and micropatterning materials. However, during the phase transition on confined patterned surfaces, how the morphologies in one liquid crystalline phase change from deformations or defects into another phase is much less known. Here, we examine the fate of defects in a LC confined on a patterned surface during smectic-A–nematic and nematic–isotropic phase transitions, using experiments and simulation analyses. Upon heating from smectic-A to nematic, a Toric focal conical domain (TFCD) melts into a +1 converging boojum defect, which then transitioned into a concentric configuration as temperature increases, attributed to a steeper decrease of the bend and twist modulus compared to splay modulus. During cooling, TFCDs are developed from two distinct pathways depending on the cooling rates. Our continuum simulation recapitulates these transformations and provides elastic constant-based explanations for the two pathways. Although the phase transition pathways of defects are independent of the geometry of the confined patterns, the arrangement of FCDs is highly dependent on the size and shape of the patterns. Finally, taken together, this simple approach offers promising opportunities for tuning the micro- or nano-patterning of topological defects in liquid crystals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Impact of particle arrays on phase separation composition patterns

We examine the symmetry-breaking effect of fixed constellations of particles on the surface-directed spinodal decomposition of binary blends in the presence of particles whose surfaces have a preferential affinity for one of the components. Our phase-field simulations indicate that the phase separation morphology in the presence of particle arrays can be tuned to have a continuous, droplet, lamellar, or hybrid morphology depending on the interparticle spacing, blend composition, and time. In particular, when the interparticle spacing is large compared to the spinodal wavelength, a transient target pattern composed of alternate rings of preferred and non-preferred phases emerges at early times, tending to adopt the symmetry of the particle configuration. We reveal that such target patterns stabilize for certain characteristic length, time, and composition scales characteristic of the pure phase-separating mixture. To illustrate the general range of phenomena exhibited by mixture-particle systems, we simulate the effects of single-particle, multi-particle, and cluster–particle systems having multiple geometrical configurations of the particle characteristic of pattern substrates on phase separation. Our simulations show that tailoring the particle configuration, or substrate pattern configuration, a relative fluid-particle composition should allow the desirable control of the phase separation morphology as in block copolymer materials, but where the scales accessible to this approach of organizing phase-separated fluids usually are significantly larger. Limited experiments confirm the trends observed in our simulations, which should provide some guidance in engineering patterned blend and other mixtures of technological interest.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Arctic soil patterns analogous to fluid instabilities

Significance Slow-moving arctic soils form patterns resembling those found in common fluids, such as paint and cake icing drips. Inspired by fluid instabilities, we develop a conceptual model for soil patterns and use mathematical analysis to predict their wavelength. In particular, we propose that soil patterns arise due to competition between gravity and cohesion or the “stickiness” of soil grains. We compare our theoretical predictions with a dataset of soil features from Norway, finding that soil patterns are controlled by fluid-like properties as well as climate. Our work provides a physical explanation for a common pattern on both Earth and Mars, with implications for our understanding of landscapes and complex materials composed of both granular and fluid components.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Thermally unstable roosts influence winter torpor patterns in a threatened bat species

Abstract Many hibernating bats in thermally stable, subterranean roosts have experienced precipitous declines from white-nose syndrome (WNS). However, some WNS-affected species also use thermally unstable roosts during winter that may impact their torpor patterns and WNS susceptibility. From November to March 2017–19, we used temperature-sensitive transmitters to document winter torpor patterns of tricolored bats (Perimyotis subflavus) using thermally unstable roosts in the upper Coastal Plain of South Carolina. Daily mean roost temperature was 12.9 ± 4.9°C SD in bridges and 11.0 ± 4.6°C in accessible cavities with daily fluctuations of 4.8 ± 2°C in bridges and 4.0 ± 1.9°C in accessible cavities and maximum fluctuations of 13.8 and 10.5°C, respectively. Mean torpor bout duration was 2.7 ± 2.8 days and was negatively related to ambient temperature and positively related to precipitation. Bats maintained non-random arousal patterns focused near dusk and were active on 33.6% of tracked days. Fifty-one percent of arousals contained passive rewarming. Normothermic bout duration, general activity and activity away from the roost were positively related to ambient temperature, and activity away from the roost was negatively related to barometric pressure. Our results suggest ambient weather conditions influence winter torpor patterns of tricolored bats using thermally unstable roosts. Short torpor bout durations and potential nighttime foraging during winter by tricolored bats in thermally unstable roosts contrasts with behaviors of tricolored bats in thermally stable roosts. Therefore, tricolored bat using thermally unstable roosts may be less susceptible to WNS. More broadly, these results highlight the importance of understanding the effect of roost thermal stability on winter torpor patterns and the physiological flexibility of broadly distributed hibernating species.

Biodiversity & Conservation↗
DOE OSTI2024

The structure and interaction of polymers affects secondary cell wall banding patterns in Arabidopsis

Abstract Xylem tracheary elements (TEs) synthesize patterned secondary cell walls (SCWs) to reinforce against the negative pressure of water transport. VASCULAR-RELATED NAC-DOMAIN 7 (VND7) induces differentiation, accompanied by cellulose, xylan, and lignin deposition into banded domains. To investigate the effect of polymer biosynthesis mutations on SCW patterning, we developed a method to induce tracheary element transdifferentiation of isolated protoplasts, by transient transformation with VND7. Our data showed that proper xylan elongation is necessary for distinct cellulose bands, cellulose–xylan interactions are essential for coincident polymer patterns, and cellulose deposition is needed to override the intracellular organization that yields unique xylan patterns. These data indicate that a properly assembled cell wall network acts as a scaffold to direct polymer deposition into distinctly banded domains. We describe the transdifferentiation of protoplasts into TEs, providing an avenue to study patterned SCW biosynthesis in a tissue-free environment and in various mutant backgrounds.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Phase Pattern Formation in Grain Boundaries

Here, in this Letter, we derive conditions that predict the existence of two-phase periodic-pattern grain boundary structures that are stable against coarsening. While previous research has established that elastic effects can lead to phase pattern formation on crystal surfaces, the possibility of stable grain boundary structures composed of alternating grain boundary phases has not been previously analyzed. Our theory identifies the specific combination of grain boundary and materials properties that enable the emergence of patterned grain boundary states and shows that the dislocation content of grain boundary phase junctions, absent in surface phenomena, weakens the stability of the patterned structures. The predictions of the theory are tested using a model copper grain boundary that exhibits multiple phases and two-phase pattern formation. We discuss how, similarly to surfaces, elastic effects associated with grain boundary phase junctions have profound implications for how grain boundary phases transform.

36 MATERIALS SCIENCE↗