Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PYRAMID”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Diagnosis of PV Cell Antireflective Coating Degradation Resulting from Hot-Humid, High Voltage Potential Aging

Corrosion of the antireflective coating on a photovoltaic cell ("ARc corrosion") has previously been observed in studies using hot-humid test conditions with external high-voltage (HV) bias. This study primarily focuses on known vulnerable, legacy aluminum back surface field (Al-BSF) cells in mini-modules (MiMos) put through comparative stepped stress tests. Each cell type had MiMos at +1500 V, -1500 V, or unbiased ("Voc") potential, which were sequentially subjected to test conditions of 60deg C/60% relative humidity (RH) for 96 h, as in International Electrotechnical Commission (IEC) Technical Specification 62804-1; 70 deg C/70% RH for 200 h; and 85 deg C/85% RH for 200 h. Characterizations at each step included visual camera and electroluminescence (EL) imaging, colorimetry, and current-voltage (I-V) curve tracing. Final characterizations included: Suns-Voc; spatial mapping of external quantum efficiency (EQE); high-resolution photoluminescence (PL), EL, and dark lock-in thermography (DLIT) imaging. Forensics were performed on extracted cores, including scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and scanning Auger microscopy (SAM). Forensics were also conducted on MiMos from previous studies that underwent stepped HV aging and separate outdoor aged full-sized modules. ARc corrosion was specifically seen for the glass/encapsulant/cell side of the +1500V (HV+) stressed MiMos and modules. Appearance, color, and reflectance were the most distinguishing characteristics relative to glass corrosion, gridline-corrosion and -delamination as well as other concurrent degradation modes. SEM/EDS and SAM identified conversion of silicon nitride to hydrated silica, hydrous silica, or hydrated amorphous silica, which preferentially occurred at the edges and tips of the pyramidal textured cell surface.

14 SOLAR ENERGY↗
DOE OSTI2026

Solutions to Droop and the Green Gap by Novel Carrier Injection

Long-wavelength (green, yellow, red) visible light-emitting diodes (LEDs) have historically been inefficient compared to blue light-emitters in the III-nitrides. This is due to many factors, including poor material quality due to the low growth temperatures required for high Incomposition InGaN quantum wells (QWs), and the polar nature of the III-nitride crystal structure. Spontaneous and piezoelectric polarization in the III-nitrides causes enhanced quantum-confined Stark effect (QCSE), which spatially separates electrons and holes and reduces radiative recombination (ie: light output) from the devices. Polarization in the crystal also induces additional potential barriers that electrons and holes must cross over before entering the QWs where they can recombine to emit light. Both of these polarization effects worsen as emission wavelength increases, making blue III-nitride LEDs are the most efficient and red III-nitride LEDs the least efficient. The focus of this project has been solving the latter polarization-related issue through the implementation of V-defects in long wavelength LEDs. V-defects are morphological defects which are commonly observed in c-plane III-nitrides. They are observed as hexagonal pyramid-shaped depressions on the c-plane surface, with six semipolar sidewalls. They typically form at the apex of threading dislocations (TDs) under conditions of kinetically-limited growth and low growth-temperature. They were initially thought to be detrimental to LED performance and much early work focused on eliminating them entirely from III-nitride devices. However, over the past decade work has emerged that indicate that they can improve LED performance by allowing electrons and holes to bypass the polarization-induced barriers present in the c-plane and directly enter the QWs of an LED. This is due to the semipolar nature of the V-defect sidewall: these sidewalls are thin and lack the polarization-induced barriers which prevent carriers easily moving between layers. V-defects have since been determined to be an efficient avenue by which to inject electrons and holes into the c-plane QWs where they can recombine to emit light. Throughout this project we have explored lateral injection through a variety of methods: simulation (Task 2), epitaxial growth of V-defect and non-V-defect LEDs (Tasks 1, 3, 4, 5, 6), and advanced characterization methods (Task 7). All tasks have been completed. A description of each task completed follows from this section.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Data-Driven Modeling and Control of Systems with Plasma-Surface Interactions (Final Technical Report)

This final technical report summarizes the activities and accomplishments in the period from February 2023 thru January 2026. The objective of the proposed research is to investigate the physical mechanisms and processes underlying the formation of structures and patterns in systems with plasma-surface interactions. In the past decades, there have been extensive studies on the interaction of glow discharges, dielectric barrier discharges, and arc discharges with confining or intervening surfaces. The advancement of the understanding of these phenomena is not only of fundamental scientific interest and relevance to the knowledge of the plasma state, but also with profound implications in various technological applications. The research will integrate theoretical, computational, and experimental work within an innovative framework of data assimilation, i.e., optimally combining model predictions with measurements. The scientific merit of this research has three aspects. Firstly, it extends the studies of plasma-surface interactions to systems with insulator surfaces and multi-layer systems, while existing studies are predominantly on electrode surfaces. Secondly, it expects to develop a novel data-driven modeling approach based on data assimilation to enhance the predictive and control capabilities, which could make transformative contributions to basic plasma research. Thirdly, it will shed new light on outstanding problems related to formation of patterns interfacing plasmas. This project also aims to launch an education and outreach initiative at Texas A&M University-Kingsville, a non-R1, minority-serving institution in South Texas. The initiative is structured as a four-tier pyramid. Tier one will be a webinar series for culture and capacity building to inform broader audience in the region about the research fields of plasma science and engineering. Tier two will be the creation and offering of an upper-level undergraduate course on introductory plasma physics, which will help with the recruitment for the upper tiers. On tier three, we will engage and mentor senior design students to conduct work toward the research goal of this project. There will also be a certificate program on general plasma science for undergrad and graduate students, part of which will be lab training at Princeton University. Tier four will be the supervision and mentoring of Ph.D. students. Therefore, this project will systematically expand the talent pipeline, broaden participation from communities historically and geographically underrepresented in DOE SC research portfolio, significantly improve the research and education capacity at the PI’s institution, and contribute to developing a diverse workforce in plasma science and engineering.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Myriad World Baseline: Global Geodemographic Estimates

The LandScan Myriad World Baseline (MWB) method produces global, residential (nighttime/home-location) gridded geodemographic estimates based on 5-year age/gender cohorts—at 30-arcsecond (≈1 km) resolution. MWB is designed to fill gaps where detailed, georeferenced survey data (e.g., Demographic and Health Surveys (DHS)) are missing or outdated, and to provide a baseline that can support human security analysis, including consequence assessment, “patterns of life” modeling, and scenario-based population futures. MWB’s workflow spatializes household-level age/gender characteristics from the GLOPOP-S dataset by conflating household and gridded expected relative wealth adapted from Global Gridded Relative Deprivation Index (GRDI), then adjusts them to a target year of interest. Age/gender estimates are then applied to harmonize lowest-administrative-level statistics with LandScan residential counts, yielding final geodemographic estimates. Two validation case studies are presented: Ghana (2021) and Tokyo/Kanagawa, Japan (2020), illustrating spatial variability in demographic cohorts and comparing MWB outputs to official gridded statistics. Results show close overall alignment relative to validation criteria including population pyramids and age-dependency ratios.

Tuccillo, Joe [ORNL] (ORCID:0000000259300943)↗
DOE OSTI2025

Orientation-Dependent Nanomechanical Behavior of Pentaerythritol Tetranitrate as Probed by Multiple Nanoindentation Tip Geometries

Nanoindentation can be leveraged to aid in the high fidelity modeling of dislocation mediated plasticity in pentaerythritol tetranitrate (PETN), an anisotropic energetic molecular crystal. Moreover, nanoindentation tip parameters such as tip geometry, size, and degree of acuity can be utilized to target anisotropic behavior. In this work, nanoindentation was conducted across a range of orientations on the (110) face of PETN to characterize resultant yield behavior, mechanical property measurements, and resultant slip behavior and fracture initiation. Three different indentation tips were utilized: a 3-sided pyramidal Berkovich tip, a 4-sided high aspect ratio Knoop tip, and a 90° conical tip. Ultimately, indenter tip radius was documented to impact yield behavior, whereas tip geometry affected larger scale processes such as slip, and tip acuity was the dominating factor that led to fracture. The axisymmetric conical tip, serving as a baseline, showed the least amount of variation in mechanical property measurements but also the largest distribution of maximum shear stress at which initial yielding occurred. Its high degree of acuity, however, was more prone to induce fracture at higher loads. The Knoop tip was shown to be suitable for average measurements, but also for elucidation of certain anisotropic features. A distinctly higher perceived hardness at 45° was measured with the Knoop tip, indicating less dislocation motion in that direction also observed in this work via scanning probe microscopy. Lastly, the commonly used Berkovich tip was a good compromise whereby it provided a representative volume element describing the average behavior of the material. These results can be utilized to target desired anisotropic behavior in a wider range of molecular crystals, as well as to inform theoretical considerations for dislocation mediated plasticity in PETN.

36 MATERIALS SCIENCE↗
NASA NTRS1962

High-Efficiency Modified Fresnel Reflectors for Solar-Energy Concentration

A study has been made of the Fresnel reflector and two variations of this reflector for use as solar-energy collectors. One variation is the conical Fresnel reflector in which the serrations are located on the inner surface of a cone. It is shown that this reflector can have a collection efficiency of 1.00 for any rim angle, if the proper cone angle is selected. Equations are developed for the design of the second variation which consists of a reflector plane that is not perpendicular to the incoming light rays. Segments of this reflector can be used to form a pyramidal collector which combines the desired flatness of the Fresnel reflector with the high efficiency of the conical Fresnel reflector. This collector can have an efficiency which is very close to 1.00 when a sufficient number of reflective sides are used.

REFLECTOR↗
NASA NTRS1964

Test device prevents molecular bounce-back

A test device, which consists of six pyramidal reflectors joined together, acts as a baffle to impede the free path of the molecule to the test item by interposing a slanted surface which imparts an angular vector to the molecule and bounces it back to the chamber wall.

Hardgrove, W. F.↗
NASA NTRS1963

THE ECONOMIC EFFECTS OF THE SPACE PROGRAM

The purpose of this paper is to discuss the economic impact of the amazing space program presented in the preceding papers. My function is to view the space program objectively as an economist so as to assess its impact upon the Nation's economy as a whole and upon certain regions in particular. In order to be objective, I will not take the extreme view that our entire lives will be changed by this program overnight-we will not all be wearing air-conditioned Moonsuits in 2 years and commuting to work by individual miniaturized Rocketpacks. An attempt will be made to avoid the other extreme of thinking that the space program is the greatest boondoggle since the Pyramids; it is not merely a form of scientific leaf-raking on a gigantic scale. My definition of the space program includes the program of the National Aeronautics and Space Administration (NASA) and some work of other agencies doing related space exploration, particularly the Department of Defense. In essence, I hope to answer the question: What will NASA's program mean to the participants in the Nation's economy?

ECONOMICS↗
NASA NTRS1966

Concave-convex growth spirals.

The simple model for introduction of a screw dislocation into a crystal leaves a step in those surfaces of the crystal that intersect the axis of the screw dislocation such that the Burgers vector has a finite component perpendicular to the surfaces. When two parallel surfaces of a crystal intersect the same screw dislocation, the resultant step, on opposite sides of the crystal, face in opposite directions. Consequently, when two such surfaces grow by accretion of the molecules at the steps, the steps wind themselves into spirals that appear to have opposite senses of rotation when viewed along the axis of the screw dislocation. Furthermore, the growth structure that results is a plano convex cone or pyramid centered on the screw dislocation. When growth occurs simultaneously on both sides of a crystal, a doubly convex structure will develop under the control of a singe screw dislocation.

Crystal growth↗
NASA NTRS1967

Tester for study of rolling element bearings

Five-ball fatigue tester makes possible the study of rolling element phenomena. The device consists of a driven test ball pyramided upon four lower balls positioned by a separator and free to rotate in an angular contact raceway.

Zaretsky, E. V.↗
NASA NTRS1969

Image position sensor

Preliminary design calculations for a proposed fine guidance experiment telescope containing a four-sided pyramidal reflector indicate that 0.01 arc sec pointing, at 0.003 arc sec sensing resolution, could be achieved by viewing a +10.0 magnitude star where the total collected light energy would be applied for fine error detection.

Rosett, B.↗
NASA NTRS1972

Analysis of requirements for GEOS-C laser cube-corner reflector panels

A mathematical analysis of the tradeoffs and requirements was performed to develop an improved array design which will give stronger returns at lower elevation angles and reduce pulse spread in the return. It was determined that a zenith angle of 75deg can be obtained with an array with an area of 0.28 sq m, if the array is shaped on the surface of a 45 deg cone whose axis is coincident to the satellite axis. The total weight of the truncated pyramid array with 270 cube corners is calculated to be not more than 50% greater than the GEOS 2 array, while the efficiency is increased 275%.

Minott, P. O.↗
NASA NTRS1972

Morphology and petrography of volcanic ashes.

Study of volcanic ash samples collected from a variety of recent eruptions using petrography, chemical analyses, and scanning electron microscopy to characterize each type and to relate ash morphology to magma composition and the type of eruption. The ashes are placed in the broad genetic categories of magmatic and phreatomagmatic. The morphology of ash particles from magmatic eruptions of high viscosity magma is governed primarily by vesicle density and shape. Ash particles from eruptions of low viscosity magmas are mostly droplets. The morphology of ash particles from phreatomagmatic eruptions is controlled by stresses within the chilled magma which result in fragmentation of the glass to form small blocky or pyramidal glass ash particles.

Heiken, G.↗
NASA NTRS1974

Anechoic chamber in industrial plants

A light anechoic chamber for routine acoustical measurements in the machine building industry is reported. The outer housing of the chamber consists of modules cast in glass fiber reinforced polyester resin; the inner housing consists of pyramidal modules cut out of sound absorbing slates. The parameters of this anechoic chamber facilitate acoustical measurements according to ISO and CAEM recommendations.

Halpert, E.↗
NASA NTRS1975

Plasma flow and fast particles in a hypervelocity accelerator - A color presentation

A new concept for particle acceleration for micrometeoroid simulation was developed at NASA Marshall Space Flight Center, using a high-density self-luminescent fast plasma flow to accelerate glass beads (with a diameter up to 1.0 mm) to velocities between 15-20 km/sec. After a short introduction to the operation of the hypervelocity range, the eight-converter-camera unit used for the photographs of the plasma flow and the accelerated particles is described. These photographs are obtained with an eight-segment reflecting pyramidal beam splitter. Wratten filters were mounted between the beam splitter and the converter tubes of the cameras. The photographs, which were recorded on black and white film, were used to make the matrices for the dye-color process, which produced the prints shown.

Igenbergs, E. B.↗
NASA NTRS1975

Application of solar energy; Proceedings of the First Southeastern Conference, Huntsville, Ala., March 24-26, 1975

Topics related to architectural and institutional considerations are discussed along with studies of components and subsystems. Subjects in the area of system design and analysis are also explored. Residential and commercial applications are considered, taking into account hot-water usage in a typical single-family residence, solar heating and cooling of mobile homes, aspects of design and performance in the case of a solar heating system using a reflective pyramid optical condenser, solar heating in a Boston school, a performance analysis of solar service hot water systems, comparative performance analyses of three solar heated and cooled buildings, and the use of solar energy in a soybeam processing operation. Applications related to power generation are also examined, giving attention to solar thermal electric power systems and photovoltaic research. Individual items are announced in this issue.

Wu, S. T.↗