Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PETN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Laser absorption measurements of temperature, pressure, CO, and CO 2 at near-MHz rates in post-detonation fireballs with comparison to synthetic measurements

A laser absorption spectroscopy (LAS) diagnostic was used to obtain measurements of temperature, pressure, CO, and CO 2 at 500 kHz or 1 MHz in post-detonation fireballs produced by hemispherical samples of pentaerythritol tetranitrate (PETN). A quantum-cascade laser was scanned over multiple CO absorption transitions near 2008.5 cm −1 at 1 MHz, while an interband-cascade laser was scanned over a CO 2 absorption transition near 2394.8 cm −1 at 500 kHz. Light from each laser was combined onto a single path and passed through a detonation chamber approximately 83 mm above the 12-mm diameter hemispherical PETN charge. The CO and CO 2 absorption signals were post-processed to obtain time histories of temperature, pressure, species column pressures (P CO L, P CO2 L), and species column mole fractions (X CO L, X CO2 L). Additionally, schlieren imaging was performed simultaneously at 500 kHz to aid interpretation of the LAS measurements. Experimental and synthetic (i.e., CFD based) LAS measurements were compared to evaluate the accuracy of the CFD model and its ability to model the turbulent afterburning of the detonation products in air. In general, the experimental measurements exhibit reasonable agreement with the synthetic measurements at early times; thereby supporting the accuracy of the CFD model. Periods of disagreement between experimental and synthetic measurements at later times are most likely due to a reflected shock and detonator cavity jetting, which are not accounted for in the CFD model.

Schwartz, Charles J. [Purdue Univ., West Lafayette↗

Near-MHz temperature and H 2 O measurements in post-detonation fireballs of 25 g hemispherical explosives using scanned-wavelength-modulation spectroscopy

A laser absorption spectroscopy diagnostic integrated within a hardened optical probe was used to measure temperature and water mole fraction at 500 kHz in post-detonation fireballs of explosives. In the experiments, an exploding-bridgewire detonator initiated a 25 g hemisphere of explosive (N5 or PETN). This produced a hemispherical fireball that traveled radially towards a hardened measurement probe. The probe contained a pressure transducer and optical equipment to pitch fiber-coupled laser light across a 12.6 cm gap onto a detector. Tunable diode lasers emitting near 7185.6 and 6806 c m − <#comment/> 1 were used to measure the absorbance spectrum of H 2 O utilizing peak-picking scanned-wavelength-modulation spectroscopy with a scan frequency of 500 kHz and modulation frequencies of 35 and 45.5 MHz, respectively. This enabled measurements of temperature and X H 2 O in the shock-heated air and trailing fireball at 500 kHz. Time histories of pressure, temperature, and H 2 O mole fraction were acquired at different standoff distances to quantify how the fireball evolved in space and time as well as to compare measured quantities between PETN and N5 fireballs. The standard deviation of temperature and X H 2 O during one representative test were found to be 17 K (1.3%) and 0.011 (5%), respectively. These measurements demonstrate this diagnostic’s ability to provide rapid and reliable measurements in harsh, highly transient post-detonation environments produced by solid explosives.

Schwartz, Charles J.↗

Fluorescence Detection and Identification of Tagging Agents and Impurities Found in Explosives

The detection and identification of 2,4,6-trinitrotoluene (TNT), 1,3,5-trinitro-1,3,5-triazacyclohexane (RDX), and pentaerythritol tetranitrate (PETN) vapors have proven to be difficult and challenging due to the low vapor pressures of these high explosives. Detecting higher vapor pressureimpurity compounds found in TNT and possible tagging agents mandated to be added to plastic explosives (RDX and PETN) would allow for easier vapor detection. The higher vapor pressure nitro compounds of interestare considered to be non-fluorescent; however, once reduced to their amino analogs, they have relatively high quantum yields. The standard reduction products, the reduction products obtained in solution, and the reduction products obtained in vapor phase were analyzed by conventional fluorescence, synchronous luminescence, and derivative spectroscopy. The nitro analogs of the isomers 1,3-diaminobenzene, 1,2- diaminobenzene, and 1,4-diaminobenzene are found as impurities inTNT. We provide for the first time the synchronous luminescencederivative spectra of these isomers; including their individual spectra and a spectrum of an isomeric mixture of the three. Using the standard reduction products associated with these isomers and other aromatic amines, our data suggest that the vapors of two signature impurities, 1,3- dinitrobenzene and 2,4-dinitrotoluene (2,4-DNT), minor impurity compounds, and two possible tagging agents, 2-nitrotoluene (2-NT) and 4- nitrotoluene (4-NT), can be detected and selectively identified using our fluorescence approach. To prove our methodology, we show that we were able to generate, collect, and reduce 2-NT, 4-NT, and 2,4-DNT vapors to their amino analogs.

Aromatic amines, Nitro aromatics, Explosive compou↗

Continuous wave laser irradiation of explosives

Quantitative measurements of the levels of continuous wave (CW) laser light that can be safely applied to bare explosives during contact operations were obtained at 532 nm, 785 nm, and 1550 nm wavelengths. A thermal camera was used to record the temperature of explosive pressed pellets and single crystals while they were irradiated using a measured laser power and laser spot size. A visible light image of the sample surface was obtained before and after the laser irradiation. Laser irradiation thresholds were obtained for the onset of any visible change to the explosive sample and for the onset of any visible chemical reaction. Deflagration to detonation transitions were not observed using any of these CW laser wavelengths on single crystals or pressed pellets in the unconfined geometry tested. Except for the photochemistry of DAAF, TATB and PBX 9502, all reactions appeared to be thermal using a 532 nm wavelength laser. For a 1550 nm wavelength laser, no photochemistry was evident, but the laser power thresholds for thermal damage in some of the materials were significantly lower than for the 532 nm laser wavelength. No reactions were observed in any of the studied explosives using the available 300 mW laser at 785 nm wavelength. Tables of laser irradiance damage and reaction thresholds are presented for pressed pellets of PBX9501, PBX9502, Composition B, HMX, TATB, RDX, DAAF, PETN, and TNT and single crystals of RDX, HMX, and PETN for each of the laser wavelengths.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Integrated Data Collection Analysis (IDCA) Program — KClO 3 (as received)/Icing Sugar

The Integrated Data Collection Analysis (IDCA) program is conducting a proficiency study for Small-Scale Safety and Thermal (SSST) testing of homemade explosives (HMEs). Described here are the results for impact, friction, electrostatic discharge, and differential scanning calorimetry analysis of a mixture of KClO 3 as received from the manufacturer mixed with icing sugar, sized through a 100-mesh sieve—KClO 3 /icing sugar (AR) mixture. This material was selected because of the challenge of performing SSST testing of a mixture of two solid materials. The mixture was found to: 1) be more sensitive to impact than RDX, similar to PETN, 2) be the same or less sensitive to friction than PETN, and 3) to be less sensitive to spark than RDX. The thermal analysis showed that the mixture has thermally stability similar to RDX and is perhaps more energetic upon decomposition but variable results indicate sampling issues. Compared to the 100-mesh sieved counter part, the KClO 3 /icing sugar (-100) mixture, the AR mixture was found to be about the same sensitivity towards impact, friction and ESD.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Integrated Data Collection Analysis (IDCA) Program — KClO 3 /Icing Sugar (-100 mesh) Mixture

The Integrated Data Collection Analysis (IDCA) program is conducting a proficiency study for Small-Scale Safety and Thermal (SSST) testing of homemade explosives (HMEs). Described here are the results for impact, friction, electrostatic discharge, and scanning calorimetry analysis of a mixture of KClO 3 sized through a 100-mesh sieve mixed with icing sugar, also sized through a 100-mesh sieve—KClO 3 /icing sugar (-100) mixture. This material was selected because of the challenge of performing SSST testing of a mixture of two solid materials. The mixture was found to be: 1) more sensitive to impact than RDX, with sensitivity similar to PETN, 2) the same or more sensitive to friction than PETN, and 3) less sensitive to spark than RDX. The analysis showed that the mixture has thermally stability similar to RDX and is perhaps more energetic upon decomposition but variable results indicate sampling issues.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Integrated Data Collection Analysis (IDCA) Program - KClO 3 /Dodecane Mixture

The Integrated Data Collection Analysis (IDCA) program is conducting a proficiency study for Small-Scale Safety and Thermal (SSST) testing of homemade explosives (HMEs). Described here are the results for impact, friction, electrostatic discharge, and differential scanning calorimetry analysis of a mixture of KClO 3 and dodecane—KClO 3 /dodecane mixture. This material was selected because of the challenge of performing SSST testing of a mixture of solid and liquid materials. The mixture was found to: 1) be more sensitive to impact than RDX, and PETN, 2) less sensitive to friction than PETN, and 3) less sensitive to spark than RDX. The thermal analysis showed little or no exothermic features suggesting that the dodecane volatilized at low temperatures. A prominent endothermic feature was observed assigned to melting of KClO 3 . This effort, funded by the Department of Homeland Security (DHS), ultimately will put the issues of safe handling of these materials in perspective with standard military explosives. The study is adding SSST testing results for a broad suite of different HMEs to the literature. Ultimately the study has the potential to suggest new guidelines and methods and possibly establish the SSST testing accuracies needed to develop safe handling practices for HMEs. Each participating testing laboratory uses identical test materials and preparation methods wherever possible. Note, however, the test procedures differ among the laboratories. The results are compared among the laboratories and then compared to historical data from various sources. The testing performers involved for the KClO 3 /dodecane mixture are Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Indian Head Division, Naval Surface Warfare Center, (NSWC IHD). These tests are conducted as a proficiency study in order to establish some consistency in test protocols, procedures, and experiments and to understand how to compare results when these things cannot be made consistent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Integrated Data Collection Analysis (IDCA) Program - KClO 4 /Aluminum Mixture

The Integrated Data Collection Analysis (IDCA) program is conducting a Proficiency Test for Small-Scale Safety and Thermal (SSST) testing of homemade explosives (HMEs). Described here are the results for impact, friction, electrostatic discharge, and differential scanning calorimetry analysis of a mixture of KClO 4 and aluminum—KClO 4 /Al mixture. This material was selected because of the challenge of performing SSST testing of a mixture of two solids. The mixture was found to be: 1) much less sensitive to impact than RDX, (LLNL being the exception) and PETN, 2) more sensitive to friction than RDX and PETN, and 3) extremely sensitive to spark. The thermal analysis showed little or no exothermic character. One prominent endothermic feature was observed in the temperature range studied and identified as a phase transition of KClO 4 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Computational Determination of the Refractive Index of TATB, LLM-105, β-HMX, & α-RDX

In this study, we use Materials Studio CASTEP, an ab initio quantum mechanical (QM) program employing density functional theory (DFT), to compute the refractive index (RI) of solid energetic materials, specifically, PETN (tetragonal phase), TATB, LLM-105, β-HMX, and α-RDX. The use of quantum mechanical DFT methods affords the investigation of the optical mate rial properties of a system without the need for any experimental input. The RI values of PETN and TATB have been experimentally determined previously and are compared here to the QM derived RI values as validation of the theoretical approach in determining material optical proper ties. To date, experimental measurements to determine the RI values for LLM-105 have yet to be determined. This fact obviates the need to determine LLM-105 RI values using quantum mechanical means.

36 MATERIALS SCIENCE↗

A BRIEF DESCRIPTION OF THE SMALL-SCALE SAFETY TESTING SYSTEMS AT LAWRENCE LIVERMORE NATIONAL LABORATORY

Small-scale sensitivity testing is important for determining material response to various stimuli including impact, friction, and static spark. These tests, briefly described below, provide parameters for safety in handling. ERL Type 12 drop hammer equipment at LLNL, shown in Figure 1, was used to determine the impact sensitivity. The equipment includes a 2.5-kg drop weight, a striker (upper anvil, 2.5 kg for solid samples and 1.0 kg for liquid samples), a bottom anvil, a microphone sensor, and a peakmeter. For each drop, sample (35 mg for solid or 45 microliter for liquid) is placed on the bottom anvil surface and impacted by the drop weight from different heights. Signs of reactions upon impact are observed and recorded. These signs include noises, flashes or sparks, smoke, pressure, gas emissions, temperature rise due to exothermic reaction, color change of the sample, and changes to the anvil surface (noted by inspection). For solid samples, a 'GO' was defined as a microphone sensor (for noise detection) response of {ge} 1.3 V as measured by a peakmeter. The higher the DH{sub 50} values, the lower the impact sensitivity. The method used to calculate DH{sub 50} values is the 'up and down' or Bruceton method. PETN and RDX have impact sensitivities of 15 and 35 cm, respectively. TATB has impact sensitivity more than 177 cm. For liquid samples, a 'GO' was determined by the noise levels as measured by the peakmeter, appearance of flashes, temperature rise of the anvil, and visual inspection of the anvil surface. Two liquid samples TMETN and FEFO have impact sensitivities of 14 and 32 cm, respectively. Figure 2 shows a 'GO' event observed during the impact sensitivity test; flashes appeared as the drop weight impacted the sample. A BAM friction sensitivity test machine, as shown in Figure 3, was used to determine the frictional sensitivity. The system uses a fixed porcelain pin and a movable porcelain plate that executes a reciprocating motion. Weight affixed to a torsion arm allows for a variation in applied force between 0.5 kg to 36.0 kg. The relative measure of the frictional sensitivity of a material is based upon the smallest load (kg) at which reaction occurs for a 1-in-10 series of attempts. The lower the load values, the higher the frictional sensitivity. PETN has a frictional sensitivity of 6.4 kg. The static spark machine at LLNL is used to evaluate the electrostatic discharge hazards (human ESD) associated with the handling of explosives. The machine was custom-built almost 30 years ago and consists of a capacitor bank (up to 20,000 pF), a voltage meter, and a discharge circuit, as shown in Figure 4. An adjustable resistor up to 510 ohms (chosen to simulate human body) is wired to the discharge circuit. A 5-mg sample is placed in a Teflon washer sealed to a steel disc and covered with a Mylar tape. High static voltage (up to 10 kv) is applied and discharged to the sample. Evidence of reaction is judged from the condition of Mylar tape, smokes, and color change of the sample. Voltage, capacitance, and resistance can be adjusted to achieve the desired static energy. The results obtained are expressed as a zero in 10 or one-in-ten at a specific voltage and joules. One reaction in ten trials at {le} 0.25 joules is considered spark-sensitive. Primary explosives show reaction at 0.1 joule.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ultraviolet Resonant Raman Enhancements in the Detection of Explosives

Raman-based spectroscopy is potentially militarily useful for standoff detection of high explosives. Normal (non-resonance) and resonance Raman spectroscopies are both light scattering techniques that use a laser to measure the vibrational spectrum of a sample. In resonance Raman, the laser is tuned to match the wavelength of a strong electronic absorbance in the molecule of interest, whereas, in normal Raman the laser is not tuned to any strong electronic absorbance bands. The selection of appropriate excitation wavelengths in resonance Raman can result in a dramatic increase in the Raman scattering efficiency of select band(s) associated with the electronic transition. Other than the excitation wavelength, however, resonance Raman is performed experimentally the same as normal Raman. In these studies, normal and resonance Raman spectral signatures of select solid high explosive (HE) samples and explosive precursors were collected at 785 nm, 244 nm and 229 nm. Solutions of PETN, TNT, and explosive precursors (DNT & PNT) in acetonitrile solvent as an internal Raman standard were quantitatively evaluated using ultraviolet resonance Raman (UVRR) microscopy and normal Raman spectroscopy as a function of power and select excitation wavelengths. Use of an internal standard allowed resonance enhancements to be estimated at 229 nm and 244 nm. Investigations demonstrated that UVRR provided ~2000-fold enhancement at 244 nm and ~800-fold improvement at 229 nm while PETN showed a maximum of ~25-fold at 244 nm and ~190-fold enhancement at 229 nm solely from resonance effects when compared to normal Raman measurements. In addition to the observed resonance enhancements, additional Raman signal enhancements are obtained with ultraviolet excitation (i.e., Raman scattering scales as !4 for measurements based on scattered photons). A model, based partly on the resonance Raman enhancement results for HE solutions, is presented for estimating Raman enhancements for solid HE samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Jack Rabbit Pretest Shadowplate Drawings For TATB IHE Model Development

The Jack Rabbit Pretest (PT) series consisted of 5 focused hydrodynamic experiments 2021E PT3, PT4, PT5, PT6, and PT7. They were fired in March and April of 2008 at the Contained Firing Facility, Site 300, Lawrence Livermore National Laboratory, Livermore, California. These experiments measured deadzone formation and impulse gradients created during the detonation of TATB based insensitive high explosive. When setting up computer simulations of the Jack Rabbit Pretest series, the modeler or code developer can execute simulations with increasing degrees of refinement using detail found in the shadowplate design. The easiest way to get started is by treating the shadowplate in each experiment as a monolithic homogeneous piece of stainless steel. The simulation of detonation would begin as a point initiation below the center, bottom surface of the shadowplate. The detonation running through the ultrafine TATB booster can be simulated using program burn and then switched over to a reactive flow detonation model as the detonation front crosses the boundary into the main charge LX-17 IHE. A modeler wanting to further refine the simulation and progression of shock through the shadowplate can use the more detailed shadowplate design information presented in this document. The source drawings are included in Appendix A of this document. Their titles and drawing numbers are listed. Each experiment's shadowplate consists of two major components. A 303 stainless steel shape that defines the outer dimensions of shadowplate and a cylindrical 303 stainless steel detonator housing that is located in a closely machined pocket in the shape. The SIMPLE ASSY drawing accurately represents the dimensions of the outer shape, it's machined cylindrical pocket, and detonator body which is treated as a monolithic, homogeneous piece of stainless steel. The detonator body cross section shows an accurately dimensioned void where the slapper flyer barrel, LX-16 (pressed PETN) pellet, and pellet can flyer barrel are located. The FULL ASSY drawing accurately represents the dimensions of the outer shadowplate shape and it's machined pocket. The detonator dimensions and materials are detailed in cross section and exploded view. All diameters, thicknesses, and materials are called out in the drawing. You will notice that the detonator includes a multilayer slapper assembly with two layers of electrically insulating Kapton sandwiching the copper foil bridge circuit. The Kapton insulated circuit is sandwiched between two thin stainless steel sheets. This slapper assembly is secured to the detonator body with two screws. There is a 0.25 mm gap between the slapper assembly and the outer shadowplate shape. The stainless steel detonator body contains an off-center titanium wheel. This titanium wheel is secured to the detonator body with one screw and two pins to maintain position and orientation of the pellet can assembly in the center of the detonator body. The titanium wheel contains a tantalum/tungsten washer and pellet can assembly. The pellet can assembly consists of a pressed LX-16 initiator pellet contained in an extruded aluminum foil can. It may be useful for the modeler to include some of the details of the shadowplate and detonator design to further refine simulations of the Jack Rabbit Pretest experiments. These details may be relevant to the progression of shock originating from the PETN initiation pellet and ultrafine TATB booster that propagates through the shadowplate.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Initiation of insensitive explosives by laser energy

Instantaneous longitudinal detonations were observed in confined columns of pentaerythritol tetranitrate (PETN), cyclotrimethylene trinitramine (RDX), and tetryl when these materials were pulsed with light energy from a focused Q-switch ruby laser. The laser energy ranged from 0.5 to 4.2 J with a pulse width of 25 ns. Enhancement of the ignition mechanism is hypothesized when a 100-nm (1000-A) thick aluminum film is vacuum-deposited on the explosive side of the window. Upon irradiation from the laser, a shock is generated at the aluminum explosive interface. Steady state detonations can be reached in less than 0.5 microseconds with less than 10% variation in detonation velocity for PETN and RDX.

Menichelli, V. J.↗

Direct laser initiation of insensitive explosives.

Instantaneous longitudinal detonations have been observed in confined columns of PETN, RDX, and tetryl when pulsed with light energy from a focused Q-switched ruby laser. The laser energy ranged from 0.5 to 4.2 J with a pulse width of 25 nsec. Enhancement of the ignition mechanism is hypothesized when a 1000 A thick aluminum film is vacuum deposited on the explosive side of the window. Upon irradiation from the laser, a shock is generated at the aluminum-explosive interface. Steady-state detonations can be reached in less than 0.5 microsec with less than 10% variation in detonation velocity for PETN and RDX.

Menichelli, V. J.↗

On calculating the equilibrium structure of molecular crystals.

The difficulty of calculating the ambient properties of molecular crystals, such as the explosive PETN, has long hampered much needed computational investigations of these materials. One reason for the shortcomings is that the exchange-correlation functionals available for Density Functional Theory (DFT) based calculations do not correctly describe the weak intermolecular van der Waals' forces present in molecular crystals. However, this weak interaction also poses other challenges for the computational schemes used. We will discuss these issues in the context of calculations of lattice constants and structure of PETN with a number of different functionals, and also discuss if these limitations can be circumvented for studies at non-ambient conditions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Characterization of energetic formulations optimized for optical initiation

Many experimental systems ignite energetic materials using lasers or other optical means. The ignition criteria can be different for each material, and will be dependent, at least, on the wavelength, power, energy density, and coherence of the light used. many of the more common energetic materials, such as HMX, PETN or RDX, are very poor light absorbers and are difficult to ignite optically, therefore the addition of a small amount ({approx} 1% by weight) of activated carbon aids in light absorption and thus ignition. However, these materials still suffer in terms of relatively large energy requirements and slow ignition times. Other materials, such ad DAATO{sub 3.5} (mixed N-oxide of 3,3-azo-bis(6-amino-1,2,4,5-tetrazine)), will ignite just from the energy supplied by a common camera flash, have very fast low-pressure burning rates, and due to decomposition mechanisms dominated by condensed phase reactions, have fast ignition times. Furthermore, the required ignition energies could be further reduced by the addition of nano-particulate transition metals (e.g. nano silver). by combining materials that are more optically sensitive with materials that are more explosively functional, interesting energetic systems with unique initiation criteria can be formulated. The optical characteristics of these formulations are examined using a 1064 nm Big Sky Nd:YAG laser and fiber optic system focused through a GRIN lens and into the sample, which is encased in a lexan holder. The energy from the laser is varied, from {approx} 0.7 mJ to {approx} 17 mJ, using neutral density filters, and is delivered in an {approx} 27.5 ns pulse. The energetic material is mixed with ethanol and slurry cast into the assembly. There are two types of ignition criteria detectable in these experiments. The first is a simple go/no-go criterion, in which any observable reaction is considered ignition, regardless of its violence. The second type requires both ignition and propagation of the reaction. By characterizing the energy required to initiate several different materials, more effective formulations can be designed using the better performing materials. Presented here are the results of laser initiation tests on a variety of compositions, principally combinations of PETN, DAATO{sub 3.5}, HMX, Ag{sub 2}BTA (silver bistetrazolamine), CuBTA, BNCP (bis-5-nitrotetrazolato tetraamine cobalt perchloriate), nm Ag, and a variety of MICs (metastable intermolecular compounds). Also presented are the conclusions as to which formulations are most suitable for optically initiated systems.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Updating Critical Temperature Calculations for Several Secondary High Explosives

In designing experiments where high explosives (HEs) are heated, it is important to have an understanding of where thermal runaway may occur. This determination is often done by using the Frank-Kamenetskii (FK) equation. For several highly-studied HEs, the parameters necessary for FK calculations are typically referenced from decades-old literature, and more recent experimental data have shown that these values require adjustment. For example, some of the legacy parameters dangerously overpredict the critical temperature by tens of degrees relative to more recent observed values. Herein, we first summarize historical results and highlight the importance of insulation effects when estimating critical temperatures for small samples, which is especially relevant to small-scale aging, compatibility, and characterization experiments. Here, we then present updated FK parameters for several common secondary CHNO HEs like RDX, HMX, PETN, and TATB, as well as the first reported values for 2,6-Diamino-3,5-dinitropyrazine-1-oxide (LLM-105). Our updated parameters produce critical-temperature curves that are consistent with both mm-scale differentical scanning calorimetry (DSC) measurements and cm-scale data from the Lawrence Livermore National Laboratory one-dimensional time-to-explosion (ODTX) experiment. In analyzing the critical temperature versus sample size curves derived from the transcendental FK equation, we discovered that these curves are remarkably well described by a simple power-law function with a universal power of 0.142 and a HE-specific scaling factor.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Hot Spot Chemistry in Several Polymer-Bound Explosives under Nanosecond Shock Conditions

Initial hot spot temperatures and temperature evolutions for 4 polymer-bound explosives under shock compression by laser-driven flyer plates at speeds from 1.5–4.5 km s -1 are presented. A new averaging routine allows for improved signal to noise in shock compressed impactor experiments and yields temperature dynamics which are more accurate than has been previously available. The PBX formulations studied here consist of either pentaerythritol tetranitrate (PETN), 1,3,5-trinitro-1,3,5-triazinane (RDX), 2,4,6-trinitrotoluene (TNT), or 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) in a 80/20 wt.% mixture with a silicone elastomer binder. The temperature dynamics demonstrate a unique shock strength dependence for each base explosive. The initial hot spot temperature and its evolution in time are shown to be indicative of chemistry occurring within the reaction zone of the four explosives. The number density of hot spots is qualitatively inferred from the spatially-averaged emissivity and appears to increase exponentially with shock strength. An increased emissivity for formulations consisting of TNT and TATB is consistent with carbon-rich explosives and in increased hot spot volume. Finally, qualitative conclusions about sensitivity were drawn from the initial hot spot temperature and rate at which the number of hot spots appear to grow.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗