Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PELLETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental Studies on Wood Pellets Combustion in a Fixed Bed Combustor Using Taguchi Method

The combustion of wood pellets in a fixed bed combustor of a 20 kW capacity domestic pellet boiler was tested according to several factors including Power, Excess Air (EA), Primary/Secondary air Split Ratio (SR) and Grate Area (GA). The Taguchi method was applied to program the experimental design. Several parameters were measured, including gas emissions (CO), fuel bed temperature (measured at 4 different heights), and efficiency. The experimental results show that the lower CO emission and the higher efficiency were obtained at medium thermal loads and the highest temperature on the fuel bed was obtained at about ¼ of its height (15 mm). The results obtained from the analysis of variance (ANOVA) show that the SR and the Power are the most important factors contributing to the CO reduction and also increase the fuel bed temperature.

Castro, Carlos↗
DOE OSTI2021

Shattered pellet penetration in low and high energy plasmas on DIII-D

Shattered pellet injection (SPI) has been adopted as the baseline disruption mitigation system for ITER, as the radiative payload penetration into DIII-D plasmas from SPI is superior to those using the massive gas injection (MGI) method. Because of the substantial differences in the energy content of ITER plasma and those in present experiments, reliable 3D MHD modeling, benchmarked against present experiments is needed to project to ITER plasmas. In support of these needs, the depth of SPI fragment penetration in DIII-D plasmas was investigated by injecting SPI into two discharges with vastly different energy content and pedestal height. 400 Torr-L pure Ne fragmented pellets at a velocity of about 200 m s−1 were injected into a 0.2 MJ L-mode discharge and a 2 MJ super H-mode discharge. Results show deep penetration of SPI fragments into low-energy plasmas in DIII-D. SPI fragment penetration is reduced as the plasma energy content increases, with some discharges exhibiting penetration that is confined to the outer regions of the plasma. The injected SPI fragments are also spread out over a distance of about 20 cm, which results in some fragments arriving near the end of or after the thermal quench is over.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Pelletized immobilized amine sorbent for CO2 capture

The disclosure describes a pelletized sorbent comprising a first component comprising Basic Immobilized Amine Sorbent, a second component comprising inorganic strength additive, and a third component comprising polymer binder, where the Basic Immobilized Amine Sorbent and solid inorganic strength additive are interconnected by the polymer binder. The pelletized sorbent is useful for removing CO2 from a gaseous mixture such as a post combustion gas stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Preliminary parameter studies to form pellets of hard materials for optical constants derived via single-angle reflectance spectroscopy

Infrared reflectance spectra can be influenced by many factors: the substrate and the thickness of the layer for liquids and the surface micromorphology, the form (powder, crystal) and the particle size for solids. All these parameters can play a role in the appearance of the measured spectrum. To avoid collecting multitudes of spectra to cover all such scenarios, the optical constants n and k, which are intrinsic properties of a material, can instead be used to model the reflectance spectrum. For solids, two techniques are often used to derive optical constants: ellipsometry and single-angle reflectance spectroscopy. For both methods, best results are usually obtained from single crystals. We have recently demonstrated for ammonium sulfate (a relatively soft material) that by optimizing certain conditions, high quality pellets with specularly reflective surfaces can be used in lieu of crystals. This was confirmed by the excellent agreement between the optical constants derived by these two methods. This work focuses on the possible extension of these methods to harder materials, starting with sodium sulfate. The first goal is to see if high quality pellet surfaces can be obtained as for ammonium sulfate. The reflectance values and the associated optical constants can also be obtained.

Diaz, Emmanuela↗
DOE OSTI2021

Effects on the Sustainable Development Goals of Wood Pellet Production in the Southeastern United States

Wood-based pellets produced in the southeastern United States (SE US) and shipped overseas for the generation of heat and power support achievement of several of the United Nation’s Sustainable Development Goals and their targets. If improperly implemented, pellet supply chains, like most energy technologies, can have negative impacts on water and air quality, biodiversity, and other ecosystem services. Cooperation between regional and local industry partners and local communities as well as readily accessible information on environmental and societal effects of the industry are important for addressing sustainability goals. Strengths of this supply chain include replacement of fossil coal with bioenergy; support for renewable energy goals; conservation of forests through sustainable, green economy jobs; and more efficient use of waste materials.

09 BIOMASS FUELS↗
DOE OSTI2021

Grain boundary enhanced UN and U3Si2 pellets with improved oxidation resistance

A method of forming a water resistant boundary on a fissile material for use in a water cooled nuclear reactor is described. The method comprises mixing a powdered fissile material selected from the group consisting of UN and U 3 Si 2 with an additive selected from oxidation resistant materials having a melting or softening point lower than the sintering temperature of the fissile material, pressing the mixed fissile and additive materials into a pellet, sintering the pellet to a temperature greater than the melting point of the additive. Alternatively, if the melting point of the oxidation resistant particles is greater than the sintering temperature of UN or U 3 Si 2 , then the oxidation resistant particles can have a particle size distribution less than that of the UN or U 3 Si 2 .

Lahoda, Edward J.↗
DOE OSTI2023

Grain boundary enhanced UN and U 3 Si 2 pellets with improved oxidation resistance

A method of forming a water resistant boundary on a fissile material for use in a water cooled nuclear reactor is described. The method comprises mixing a powdered fissile material selected from the group consisting of UN and U3Si2 with an additive selected from oxidation resistant materials having a melting or softening point lower than the sintering temperature of the fissile material, pressing the mixed fissile and additive materials into a pellet, sintering the pellet to a temperature greater than the melting point of the additive. Alternatively, if the melting point of the oxidation resistant particles is greater than the sintering temperature of UN or U3Si2, then the oxidation resistant particles can have a particle size distribution less than that of the UN or U3Si2.

Lahoda, Edward J.↗
DOE OSTI2022

Pellet Cladding Interaction In-Reactor Ramp Testing in a World without the Halden Boiling Water Reactor

One of the most crucial performance areas for fuel rods in water cooled nuclear power plants is interaction between cladding tubes and fuel pellets. Experimental programs in test reactors have provided key data to help fuel developers and plant operators understand Pellet Cladding Interaction (PCI) phenomena and optimize their strategies for reliable fuel performance. Approximately 50 years of “ramp” testing programs, where the fission heating rate is deliberately manipulated in test rods, have been performed in a handful of test reactors to reveal and understand PCI behaviors such as iodine-assisted stress corrosion cracking. Unfortunately, the test reactors most engaged in this type of work have all been retired over the years up to the recent and unexpected closure of the Halden Boiling Water Reactor which effectively caused a hiatus in PCI ramp testing programs. The need for ramp testing is crucial at this time to enable refined PCI understanding as more plants consider implementing flexible operations, increased fuel rod burnup limits, and new fuel technologies with enhanced accident tolerance. This paper reviews some of the key PCI phenomena that must be addressed with in-pile testing and surveys past test reactor’s methods for achieving the needed conditions. A strategic approach is then presented using test reactors and complimentary facilities which are still available today. Near term data opportunities are put forth along with capability development strategies that will ensure future longevity in this field of research.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Understanding the Influence of Water-Soluble Compounds from Unpretreated Corn Stover Pellets on Enzymatic Hydrolysis of Cellulose

Aqueous extractives are minor and non-structural compounds in biomass that can be extracted using solvents, while contributing significantly to lignocellulose characteristics. Yet their roles in enzyme-mediated processing of lignocellulosic biomass remain elusive. Here, we examine the composition and features of extractives derived from untreated pelleted corn stover as well as their effects on enzymatic hydrolysis. Unlike the observations described in previous reports, we find that water extractable material improves the enzymatic hydrolysis of extractive-free stover by 67% with a glucose yield increase from 12% to 20% with 6 FPU cellulase per g glucan, whereas the enzyme activities are diminished when using microcrystalline cellulose as a substrate. The different behavior of corn stover and microcrystalline cellulose is likely attributed to the presence of lignin, which may interact with inhibitory compounds such as phenolics, mitigating the detrimental impacts of soluble inhibitors or insoluble lignin or both. These findings advance our fundamental understanding of the intrinsic behavior of extractives and help to optimize the schemes for efficient and cost-competitive enzymatic conversion of lignocellulose.

09 BIOMASS FUELS↗
DOE OSTI2025

High-Fidelity CFD Modeling of Cryogenic Hydrogen Isotope Extrusion for Fusion Reactor Pellet Fueling

This study investigates the extrusion processes of deuterium and protium using ANSYS-Polyflow. The geometries and computational fluid dynamics (CFD) settings closely replicate the experimental setups and data acquired from the extruder experiments at Oak Ridge National Laboratory (ORNL) for validation purposes. We explore the impacts of (1) slip versus non-slip boundary conditions and (2) the use of constant, temperature-, and shear rate–dependent viscosities, concluding that the implementation of non-slip wall boundary conditions combined with shear rate–dependent viscosity produced more accurate predictions. The simulations achieved excellent agreement with the experimental data, with relative differences of only 5% for deuterium, and 3% to 6% for protium. This is the first time that experimental extrusion data at ORNL have been accurately predicted through high-fidelity CFD modeling. In conclusion, the advancements offer valuable insights and a foundational modeling tool for optimizing pellet injectors for ITER and other future reactor-scale devices.

ANSYS-Polyflow↗
DOE OSTI2026

Radiation asymmetry during shattered pellet and massive gas injection in DIII-D

Infrared thermography of the first wall in DIII-D is used to show the toroidal peaking of plasma radiation during mitigated disruptions with shattered pellet injection (SPI) and with massive gas injection (MGI). During MGI, the radiation peak location is shown to be due to the n = 1 magnetohydrodynamic (MHD) activity and continuously variable in toroidal phase based on externally applied error fields, consistent with previous experimental results. Furthermore, the measured toroidal peaking factor (TPF) is in agreement with the previous estimates based on radiometry, with a total TPF of 1.07 ± 0.05 when integrated over the entire duration of the disruption, and a value of 1.3 ± 0.1 during the thermal quench (TQ). For SPI, the location of the radiation peak is found to be determined predominantly by the particle source location, and thus can be varied on DIII-D by injecting from either of two toroidally separated injectors. 3D non-linear MHD simulations with the NIMROD code support this picture. The localized SPI particle source leads to higher peaking than for MGI, with a total TPF of 1.3 ± 0.1 over the full disruption and a TQ TPF of 1.9 +0.5/−0.3, a value also consistent with the NIMROD simulations. This TQ value is close to or potentially exceeding the allowable limit for the previously planned Be first wall in ITER, pointing to the importance of radiation asymmetries depending on the choice of first wall material.

Physics - Plasma physics↗
DOE OSTI2021

Shattered pellet injection experiments at JET in support of the ITER disruption mitigation system design

A series of experiments have been executed at JET to assess the efficacy of the newly installed shattered pellet injection (SPI) system in mitigating the effects of disruptions. Issues, important for the ITER disruption mitigation system, such as thermal load mitigation, avoidance of runaway electron (RE) formation, radiation asymmetries during thermal quench mitigation, electromagnetic load control and RE energy dissipation have been addressed over a large parameter range. The efficiency of the mitigation has been examined for the various SPI injection strategies. Here, the paper summarises the results from these JET SPI experiments and discusses their implications for the ITER disruption mitigation scheme.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

A Prototype High-Voltage Pulsed Power Supply for Control of the ITER Shattered Pellet Injection System Flyer Plate Valve

A high-voltage pulsed power supply (HVPPS) has been designed, prototyped, and tested for driving an eddy current actuated propellant valve for the International Thermonuclear Experimental Reactor (ITER) disruption mitigation system. The high-voltage (HV) dc supply output voltage is software programmable, and the energy storage capacitor bank can be readily reconfigured as 200, 400, 600, and 800 μ F, enabling testing and optimization of both the valve drive and valve systems. Multiple system parameters are monitored before, during, and after each firing of the valve. The system parameters are both displayed and stored for further analysis. Control of the setup, firing sequence, and data collection is automated using a LabVIEW-based control program. The programmability and reconfigurability of this system collectively provide a flexible and robust platform for system refinement and optimization. In this article, a summary of the system will be provided including operational sequences, HV switching and associated triggering methods and circuits, and results measured while firing a solid frozen pellet. Additionally, planned refinement activities toward meeting all requirements for ITER integration will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

SPC-70774 Rev 0 MARVEL Black Rod B4C Pellets Print Fabrication Specification

A. Idaho National Laboratory (INL) is developing a microreactor to produce electrical power utilizing a small nuclear core and Stirling engines under the Microreactor Application Research Validation and Evaluation (MARVEL) program. This procurement specification defines the requirements for fabrication of the MARVEL Black Rod B4C pellets. B. Any conflict between this specification and referenced Codes and Standards, or any supplementary specifications in the procurement documents requires written clarification from the Contractor prior to proceeding with any work. Any deviation from the procurement documents requires approval by the Contractor with the change request process.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2025

Material extrusion with integrated compression molding of NdFeB/SmFeN nylon bonded magnets using small- and large-scale pellet-based 3D-printers

High-density bonded rare-earth magnets are manufactured using pellet-fed additive manufacturing (AM)/material extrusion and an integrated additive manufacturing-compression molding (AM-CM) process. Neodymium iron boron – samarium iron nitride in polyamide 12 (NdFeB-SmFeN/PA12) of 93 % weight fraction (65 % volume fraction) are used for the study. The mechanical properties (tensile strength and modulus), magnetic properties (maximum energy density, coercivity, remanence) are reported. Manufacturing parameters such as layer height, barrel temperatures, screw speed and gantry feed rate are optimized to obtain the highest possible density of the magnets using a small-scale desktop material extrusion printer. Large scale integrated additive manufacturing-compression molding (AM-CM) is then utilized to increase the density of the magnets by reducing porosity defects common in the material extrusion process. The density of as-printed magnets was 5.2 g/cm 3 with a BH max value of 124.14 kJ/m 3 , tensile strength of 20 MPa and a modulus of 2 GPa. AM-CM increased the density of the compound by 5.5 % (5.49 g/cm 3 ). The reduction in porosity was confirmed using X-ray tomography (XCT). Improvement in mechanical strength of the material was also observed, with an increase in tensile strength of 25 % (25.09 MPa) and increase in tensile modulus of 275 % (5.49 GPa). Scanning electron microscopy showed increased particle-matrix adhesion with the integrated AM-CM process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

New strategy for liquefying corn stover pellets

The movement of solid material into and between unit operations within a biorefinery is a bottleneck in reaching design capacity, with formation of biomass slurries needed to introduce feedstock. Corn stover slurries have been achieved from dilute acid, pretreated materials resulting in slurry concentrations of up to about 150 g/L, above which flowability is compromised. We report a new strategy to liquefy corn stover at higher solids concentration (300 g/L) by initially cooking it with the enzyme mimetic maleic acid at 40 mM and 150°C. This is followed by 6 h of enzymatic modification at 1 FPU (2.2 mg protein)/g solids, resulting in a yield stress of 171 Pa after 6 h and 58 Pa in 48 h compared to 6806 Pa for untreated stover. Mimetic treatment of corn stover pellets minimizes the inhibitory effect of xylo-oligomers on hydrolytic enzymes. Furthermore, this strategy allows for the delivery of solid lignocellulosic slurry into a pretreatment reactor by pumping, improving operability of a biorefinery.

09 BIOMASS FUELS↗
DOE OSTI2025

Accelerated and heterogeneous corrosion of Cr-doped uranium nitride fuel pellets

The steam oxidation of Cr-doped UN fuel pellets is analyzed during sequential isothermal holds up to 720 °C. In situ neutron diffraction results show how Cr is accommodated in a secondary U 2 CrN 3 phase, leading to the formation of a duplex UN/U 2 CrN 3 microstructure. Under corrosion, the oxidation of the two phases begins at 400 °C for UN and 430 °C for U 2 CrN 3 , respectively. Because the UN phase is preferentially oxidized in the presence of U 2 CrN 3 , addition of Cr in UN based nuclear fuel is found to accelerate the corrosion rate. At 430 °C the oxidation of UN in the UN/U 2 CrN 3 microstructure is ~ 5 times faster than pure UN, increasing to ~19 times faster at 460 °C. The oxidation of U 2 CrN 3 produces UO 2 via the formation of two transient intermediate phases. In situ neutron diffraction enables oxidation processes of UN and U 2 CrN 3 components to be followed separately within the two-phase system.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Reduced-order CFD modeling of cryogenic hydrogen isotope extrusion for pellet fueling

This study presents a reduced-order model (ROM) for computational fluid dynamics (CFD) simulations of cryogenic hydrogen isotope extrusions, focusing on protium (H₂) and deuterium (D₂) piston extruders. Using a 2D axisymmetric ROM in ANSYS-Polyflow, significant computational savings were achieved (runtime reduced from 9∼24 h to 3∼5 min), with extrusion force discrepancies between the 2D ROM and 3D models being on the order of 1%. Parametric studies identified optimal cutoff shear rates in the viscosity model (0.01/s for H₂ and 0.001/s for D₂), providing recommendations for future simulations. Finally, a comprehensive comparison of ROM results with experimental data was performed across varying geometries, cryogenic materials, temperatures, extrusion lengths, and piston velocities. Predictions at low extrusion temperatures met the objective of providing quick and efficient solutions with an acceptable extrusion force error of approximately 10% or less, validating the effectiveness of the 2D ROM approach. However, at high temperatures closer to the triple point, extrusion force error grows, which necessitates developing an improved model that accounts for temperature effects, e.g. melting. Nevertheless, the findings still represent a significant improvement in efficiency of CFD modeling of cryogenic hydrogenic extrusion. The ROM framework can also be extended to tritium (T2) and screw extruders, which will ultimately provide a fast and effective tool for optimizing pellet injector design for ITER and future reactor systems.

Fan, Joy [ORNL] (ORCID:0000000229751735)↗