Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PAST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Low temperature sintering of lanthanum strontium manganite-based contact pastes for SOFCs

Electrical contact pastes of composition (La0.90Sr0.10)0.98MnO3+δ (LSM-10) formed strong bonds (~3 MPa) to (Co,Mn)3O4 spinel-coated Crofer 22 APU ferritic steel coupons when exposed to alternating flows of air and nitrogen (10 ppm O2) at 900oC for 2 hours or longer. When held at 900oC in air only, bond strengths were negligible. Substantial bonds could also be created between LSM-10 contact paste and (La0.80Sr0.20)0.98MnO3+δ (LSM-20) porous cathodes by processing in alternating air and nitrogen, without simultaneous densification of the cathode. Enhanced sintering of LSM-10 is attributed to transients in the defect structure induced by oxygen partial pressure changes.

36 MATERIALS SCIENCE↗

A large increase in U.S. methane emissions over the past decade inferred from satellite data and surface observations

Abstract The global burden of atmospheric methane has been increasing over the past decade, but the causes are not well understood. National inventory estimates from the U.S. Environmental Protection Agency indicate no significant trend in U.S. anthropogenic methane emissions from 2002 to present. Here we use satellite retrievals and surface observations of atmospheric methane to suggest that U.S. methane emissions have increased by more than 30% over the 2002–2014 period. The trend is largest in the central part of the country, but we cannot readily attribute it to any specific source type. This large increase in U.S. methane emissions could account for 30–60% of the global growth of atmospheric methane seen in the past decade.

54 ENVIRONMENTAL SCIENCES↗

Effect of the Soldering Atmosphere on the Wettability Between Sn4.0Ag0.5Cu (in wt.%) Lead-Free Solder Paste and Various Substrates

The “degree of wetting,” which is related to the contact angle (θ) between the molten solder and the substrate, is a useful parameter on the solderability process control. The contact angle, however, is strongly dependent on the type of substrate surface finish and used atmosphere (inert or non-inert). Furthermore, the surface tension, being an important parameter on the solderability process and performance, can also be achieved if the contact angle is known. In this study, the SAC405 [Sn4.0Ag0.5Cu (in wt.%)] solder paste contact angle was measured, by the “sessile drop” method, as a function of the temperature, surface pad finish and used atmosphere. The results are discussed, and the contact angles obtained for the different conditions are compared and discussed. Then, the surface tension (experimental) was obtained from the measured contact angle and compared with the obtained by using computation models (theoretical). The experiments performed in high vacuum conditions, i.e., low oxygen content, over a temperature range, allowed the evaluation and understanding of the surface oxides layers role on the solder wettability. The present study shows that in the soldering process, even in an inert atmosphere, usually used in industry, occurs the formation of superficial oxides, over the liquid solder and/or at the pad surfaces, that strongly affects the solder paste wettability, specially with Sn and OSP (organic solderability preservative) finishing. Differences in contact angle of ≥ 10° were determined between the two types of used atmospheres. The experimental surface tension and theoretical surface tension obtained, for the NiAu substrate type, present good correlation. The lower contact angle values were obtained for the NiAu and OSP finish types, independently of the atmosphere type.

36 MATERIALS SCIENCE↗

Phase development in conventional and active belite cement pastes by Rietveld analysis and chemical constraints

High belite cements may be an alternative to reduce CO{sub 2} emissions. Although CO{sub 2} emissions may be depleted up to 10%, unfortunately, the hydration reactivity of belite phases is slow which leads to low mechanical strengths at early ages. In order to enhance their hydraulic reactivity, the activation of these cements by doping with alkaline oxides has been proposed. Here, we have synthesised a laboratory belite clinker without activation (47 wt.% of {beta}-C{sub 2}S and 19 wt.% of {alpha}{sub H}'-C{sub 2}S) and two alkaline oxide activated clinkers (one with 13 wt.% of {beta}-C{sub 2}S, 24 wt.% of {alpha}{sub H}'-C{sub 2}S and 19 wt.% of {alpha}-C{sub 2}S; and the second with 12 wt.% of {beta}-C{sub 2}S, 42 wt.% of {alpha}{sub H}'-C{sub 2}S and 5 wt.% of {alpha}-C{sub 2}S). We have also developed a methodology to analyse quantitatively the phase evolution of cement pastes and we have applied it to these high belite cements. Rietveld quantitative phase analysis of synchrotron X-ray powder diffraction data, together with chemical constraints, is used to determine the phase development up to 1 year of hydration in the belite cement pastes. {beta}-C{sub 2}S almost does not react during the first 3 months, meanwhile {alpha}{sub H}'-C{sub 2}S reacts on average more than 50% in the same period. Moreover, the degree of reaction of {alpha}-C{sub 2}S is slightly larger (on average about 70% after three months) than that of {alpha}{sub H}'-C{sub 2}S. Full phase analyses are reported and discussed including the time evolution of amorphous phases and free water.

36 MATERIALS SCIENCE↗

Characterization by solid-state NMR and selective dissolution techniques of anhydrous and hydrated CEM V cement pastes

The long term behaviour of cement based materials is strongly dependent on the paste microstructure and also on the internal chemistry. A CEM V blended cement containing pulverised fly ash (PFA) and blastfurnace slag (BFS) has been studied in order to understand hydration processes which influence the paste microstructure. Solid-state NMR spectroscopy with complementary X-ray diffraction analysis and selective dissolution techniques have been used for the characterization of the various phases (C{sub 3}S, C{sub 2}S, C{sub 3}A and C{sub 4}AF) of the clinker and additives and then for estimation of the degree of hydration of these same phases. Their quantification after simulation of experimental {sup 29}Si and {sup 27}Al MAS NMR spectra has allowed us to follow the hydration of recent (28 days) and old (10 years) samples that constitutes a basis of experimental data for the prediction of hydration model.

36 MATERIALS SCIENCE↗

Critical aspects of nano-indentation technique in application to hardened cement paste

Several open questions related to the experimental protocol and processing of data acquired by the nano-indentation (NI) technique are investigated. The volume fractions of mechanically different phases obtained from statistical NI (SNI) analysis are shown to be different from those obtained by back-scattered electron (BSE) image analysis and X-ray diffraction (XRD) method on the same paste. Judging from transmission electron microscope (TEM) images, the representative volume element of low-density calcium-silicate hydrates (C-S-H) can be considered to be around 500 nm, whereas for high-density C-S-H it is about 100 nm. This raises the question how the appropriate penetration depth for NI experiments should be selected. Changing the maximum load from 1 mN to 5 mN, the effect of penetration depth on the experimental results is studied. As an alternative to the SNI method, a 'manual' indentation method is proposed, which combines information from BSE and atomic-force microscopy (AFM), coupled to the NI machine. The AFM allows to precisely indent a high-density C-S-H rim around unhydrated clinkers in cement paste. Yet the results from that technique still show a big scatter.

36 MATERIALS SCIENCE↗

Influence of the cementitious paste composition on the E-modulus and heat of hydration evolutions

E-modulus and heat of hydration are features of cement-based materials that follow a rapid rate of change at early ages. This paper analyses the influence of the composition of cementitious pastes on these features by using two methods: (i) a novel technique for continuously monitoring the E-modulus of cement-based materials, based on evaluating the first resonant frequency of a composite beam containing the material under testing, and (ii) an isothermal calorimeter to determine the released heat of hydration. Seventeen mixes are tested, encompassing pastes with five w/c ratios, as well as different contents of limestone filler, fly ash, silica fume and metakaolin. The results permit the comparison of the E-modulus and heat of hydration sensitivities to mix composition changes, and to check possible relations between these features. This work also helps to establish the technique (i) as a non-destructive method for monitoring the E-modulus evolution in cement-based materials since casting.

36 MATERIALS SCIENCE↗

On the use of peak-force tapping atomic force microscopy for quantification of the local elastic modulus in hardened cement paste

A surface of epoxy-impregnated hardened cement paste was investigated using a novel atomic force microscopy (AFM) imaging mode that allows for the quantitative mapping of the local elastic modulus. The analyzed surface was previously prepared using focussed ion beam milling. The same surface was also characterized by electron microscopy and energy-dispersive X-ray spectroscopy. We demonstrate the capability of this quantitative nanomechanical mapping to provide information on the local distribution of the elastic modulus (from about 1 to about 100 GPa) with a spatial resolution in the range of decananometers, that corresponds to that of low-keV back-scattered electron imaging. Despite some surface roughness which affects the measured nanomechanical properties it is shown that topography, adhesion and Young's modulus can be clearly distinguished. The quantitative mapping of the local elastic modulus is able to discriminate between phases in the cement paste microstructure that cannot be distinguished from the corresponding back-scattered electron images.

36 MATERIALS SCIENCE↗

E-modulus evolution and its relation to solids formation of pastes from commercial cements

Models for early age E-modulus evolution of cement pastes are available in the literature, but their validation is limited. This paper provides correlated measurements of early age evolution of E-modulus and hydration of pastes from five commercial cements differing in limestone content. A recently developed methodology allowed continuous monitoring of E-modulus from the time of casting. The methodology is a variant of classic resonant frequency methods, which are based on determination of the first resonant frequency of a composite beam containing the material. The hydration kinetics - and thus the rate of formation of solids - was determined using chemical shrinkage measurements. For the cements studied similar relationships between E-modulus and chemical shrinkage were observed for comparable water-to-binder ratio. For commercial cements it is suggested to model the E-modulus evolution based on the amount of binder reacted, instead of the degree of hydration.

36 MATERIALS SCIENCE↗

On the physico-chemical evolution of low-pH and CEM I cement pastes interacting with Callovo-Oxfordian pore water under its in situ CO{sub 2} partial pressure

Within the framework of geological repositories for radioactive waste, structural concretes must be adapted to the underground chemical conditions. CEM I cement-based materials are characterised by high pH that may produce an alkaline plume in the near-field of the repository. In order to avoid this problem, low-pH cements have been designed. This study compares the physico-chemical behaviour of a low-pH material with a CEM I cement paste, both being subjected to leaching by an aqueous solution. An original experimental setup was designed to reproduce the underground conditions using a specific CO{sub 2} regulation device. Under these conditions, the low-pH material was strongly degraded, which results in coarser porosity, whereas thickness degradation of the CEM I cement paste is limited by the precipitation of a magnesium-calcite crust over the surface, which reduces the exchange of soluble species. This paper also presents a new approach for microstructure characterisation based on high-resolution X-ray microtomography.

36 MATERIALS SCIENCE↗

Impact of the associated cation on chloride binding of Portland cement paste

Well hydrated cement paste was exposed to MgCl{sub 2}, CaCl{sub 2} and NaCl solutions at 20 °C. The chloride binding isotherms for free chloride concentrations ranging up to 1.5 mol/l were determined experimentally. More chlorides were found to be bound when the associated cation was Mg{sup 2} {sup +} or Ca{sup 2} {sup +} compared to Na{sup +}. The chloride binding capacity of the paste appeared to be related to the pH of the exposure solution. In order to explain the cation dependency of the chloride binding a selection of samples was investigated in detail using experimental techniques such as TG, XRD and SEM–EDS to identify the phases binding the chlorides. The experimentally obtained data were compared with the calculations of a thermodynamic model, GEMS. It was concluded that the measured change in chloride binding depending on the cation was mainly governed by the pH of the exposure solution and thereby the binding capacity of the C-S-H.

36 MATERIALS SCIENCE↗

Characterization of morphology and hydration products of high-volume fly ash paste by monochromatic scanning x-ray micro-diffraction (μ-SXRD)

The present study focuses on identification and micro-structural characterization of the hydration products formed in high-volume fly ash (HVFA)/portland cement (PC) systems using monochromatic scanning x-ray micro-diffraction (μ-SXRD) and SEM-EDS. Pastes with up to 80% fly ash replacement were studied. Phase maps for HVFA samples using μ-SXRD patterns prove that μ-SXRD is an effective method to identify and visualize the distribution of phases in the matrix. μ-SXRD and SEM-EDS analysis shows that the C-S-H formed in HVFA system containing 50% or more of fly ash has a similar structure as C-S-H(I) with comparatively lower Ca/Si ratio than the one produced in PC system. Moreover, coexistence of C-S-H(I) and strätlingite is observed in the system containing 80% of fly ash, confirming that the amount of alumina and silicate phases provided by the fly ash is a major factor for the formation of C-S-H(I) and strätlingite in HVFA system. - Highlights: • High-volume fly ash (HVFA) paste was studied by scanning x-ray micro-diffraction. • Coexistence of C-S-H(I) and strätlingite in the HVFA system is clearly shown. • The distribution of minor phases in the HVFA system is shown. • Differences between inner and outer products of fly ash are observed by SEM-EDS.

36 MATERIALS SCIENCE↗

The impact of sulphate and magnesium on chloride binding in Portland cement paste

The effect of magnesium and sulphate present in sea water on chloride binding in Portland cement paste was investigated. Ground well hydrated cement paste was exposed to MgCl{sub 2}, NaCl, NaCl + MgCl{sub 2}, MgSO{sub 4} + MgCl{sub 2} and artificial sea water solutions with a range of concentrations at 20 °C. Chloride binding isotherms are determined and pH of the solutions were measured. A selection of samples was examined by SEM-EDS to identify phase changes upon exposure. The experimental data were compared with calculations of a thermodynamic model. Chloride binding from sea water was similar to chloride binding for NaCl solutions. The magnesium content in the sea water lead to a slight decrease in pH, but this did not result in a notable increase in chloride binding. The sulphate present in sea water reduces both chloride binding in C–S–H and AFm phases, as the C–S–H incorporates more sulphates instead of chlorides, and part of the AFm phases converts to ettringite.

36 MATERIALS SCIENCE↗

Temperature influence on water transport in hardened cement pastes

Describing water transport in concrete is an important issue for the durability assessment of radioactive waste management reinforced concrete structures. Due to the waste thermal output such structures would be submitted to moderate temperatures (up to 80 °C). We have then studied the influence of temperature on water transport within hardened cement pastes of four different formulations. Using a simplified approach (describing only the permeation of liquid water) we characterized the properties needed to describe water transport (up to 80 °C) using dedicated experiments. For each hardened cement paste the results are presented and discussed.

36 MATERIALS SCIENCE↗

Porous structure and mechanical strength of cement-lime pastes during setting

The acceleration of a cement paste setting as a result of lime addition may be shown from isothermal calorimetry measurements. We investigated the underlying mechanisms through two techniques that provide information on porous structure (using Nuclear Magnetic Resonance) and mechanical properties (elastic modulus measured by rheometry). The correlation of the two sets of results on a cement paste clearly reveals the successive steps of setting, and particularly highlights the so-called induction period. We show that this induction period disappears in the presence of lime, leading to an acceleration of the setting. We also show that beyond some critical concentration of added lime the acceleration of setting is negligible.

36 MATERIALS SCIENCE↗

Investigation of the changes in microstructure and transport properties of leached cement pastes accounting for mix composition

Ca-leaching of cement-based materials induces detrimental effects on properties related to long-term durability. A better understanding of leaching degradation in terms of alterations in mineralogy, microstructure, and transport properties is important for long-term assessments of concrete and reinforced concrete structures used in nuclear waste disposal systems or in hydro structures. However, the decalcification process is not easy to study because it is extremely slow. In this study, an ammonium nitrate (NH{sub 4}NO{sub 3}) solution of 6 mol/l was used to accelerate the leaching kinetics. The experiments were performed on cement paste samples with different water/powder (w/p) and limestone filler (LS) replacement ratios. Both the change of sample mass over time and the amount of calcium ion leached out were monitored during the test. Different post-analysis techniques including SEM/SEM-EDX, XRD/QXRD, MIP, ion chromatography, and N{sub 2}-adsorption were used to characterize the microstructural and mineralogical changes. The effect of accelerated leaching on transport properties was studied by measuring the changes in water permeability and diffusivity of dissolved gases. Results showed that the square-root-time law of degradation was applicable under accelerated conditions. Both higher w/p ratios and LS replacements increased the rate of leaching propagation; the former had a more significant effect. The accelerated leaching significantly altered the microstructure of the cement paste to a material with a higher specific surface area, increased total porosity and a shift to larger pore sizes. Those changes led to a significant increase in water permeability (one to two orders of magnitude) and diffusivity (less than one order) depending on degradation state.

36 MATERIALS SCIENCE↗

Water dynamics in cement paste at early age prepared with pozzolanic volcanic ash and Ordinary Portland Cement using quasielastic neutron scattering

Early age hydration kinetics of Portland cement with pozzolanic volcanic ash was examined using quasielastic neutron scattering. Volcanic ash consisting of two different particle sizes was used to prepare cement pastes with different ratios of Portland cement to volcanic ash. The concentration of the volcanic ash played a major role in the bound water index and self-diffusion coefficients of hydration water confined in the cement paste. An increase in the particle size of the volcanic ash affected the degree of hydration by allowing more free and mobile water in the gel pores, suggesting that volcanic ash may not have completely reacted during the experimental time frame. This study shows that the particle size along with variation in volcanic ash composition governs the early age hydration process in volcanic ash cements.

36 MATERIALS SCIENCE↗

Influence of triethanolamine on the hydration product of portlandite in cement paste and the mechanism

The influences of triethanolamine (TEA) on the portlandite in hardened cement pastes (HCPs) were systematically investigated. Results show that the addition of TEA in cement pastes leads to a visible reduction of Ca(OH){sub 2} (CH) content and considerably alters the morphology of CH crystals from large and parallel-stacked lamellar shape to smaller and distorted actinomorphic one. For the first time, the CH micro-crystals and even non-crystalline CH in HCPs were observed in the presence of TEA. Due to integration of CH micro-crystals in C–S–H phase, remarkable higher Ca/Si ratio of C–S–H phase was found. The formation of TEA-Ca{sup 2+} complex via the interaction between Ca{sup 2+} and the oxygen atoms in TEA molecule was evidenced by the results of NMR and UV. It is believed that TEA can be introduced into the crystallization process of portlandite and thus significantly alters the morphology of CH crystals and even the content of the crystalline CH phase.

36 MATERIALS SCIENCE↗