Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Oxidation behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Invited Review Paper in Commemoration of Over 50 Years of Oxidation of Metals: Addressing the Role of Water Vapor on Long-Term Stainless Steel Oxidation Behavior

In the past 20 years, it has become clear that the long-term exposure of chromia-forming austenitic stainless steels to air containing ~ 10 vol% water vapor at 650–800 °C significantly increases the Cr consumption rate compared to laboratory air. However, a similar acceleration does not occur in 100% steam because O 2 is not available to form volatile CrO 2 (OH) 2 . As the research has shown, this accelerated Cr loss is particularly important for thin-walled components like gas turbine recuperators. Typically, conventional austenitic stainless steels exhibit accelerated attack (i.e., rapid formation of Fe-rich oxide nodules), while higher alloyed steels resist this type of degradation until the alloy surface becomes Cr depleted. The development of strategies and solutions for this issue are reviewed. Model Fe–Cr–Ni alloys have been used to study composition effects on this behavior. For example, increasing the Mn content up to ~ 4 wt% was not beneficial, but increasing the Ni content improved oxidation resistance in this environment. However, at 650–700 °C even highly alloyed steels showed surface Cr depletion at alloy grain boundaries resulting in Fe-rich oxide nodule formation. The path forward for this issue will require more refined mechanistic understanding and increased used of modeling to develop better application-specific lifetime models to identify the most cost-effective alloy solutions.

36 MATERIALS SCIENCE↗

Oxidation Behavior of HfB2-SiC Materials in Dissociated Environments

Hafnium diboride based materials have shown promise for use in extremely high temperature applications, such as sharp leading edges on future reentry vehicles. During reentry, the oxygen and nitrogen in the atmosphere are dissociated by the shock layer ahead of the sharp leading edge such that surface reactions are determined by reactions of monatomic oxygen and nitrogen rather than O2, and N2. Simulation of the reentry environment on the ground requires the use of arc jet (plasma jet) facilities that provide monatomic species and are the closest approximation to actual flight conditions. Simple static or flowing oxidation studies under ambient pressures and atmospheres are not adequate to develop an understanding of a materials behavior in flight. Arc jet testing is required to provide the appropriate stagnation pressures, heat fluxes, enthalpies, heat loads and atmospheres encountered during flight. This work looks at the response of HfB2/SiC materials exposed to various simulated reentry environments.

Ellerby, Don↗

Microstructure and oxidation behavior of high strength steel AISI 410 implanted with nitrogen ion

Surface treatment by implantation with nitrogen-ion was performed on the commercial feritic high strength steel AISI 410 which is termed for high temperature applications. The aim of this research was focused on the surface modification to improve its high temperature oxidation property in the early stages. Ion implantation was carried out at acceleration energy of 100 KeV and ion current 10 mA for 30, 60 and 90 minutes. The samples were subjected to the high temperature oxidation test by means of thermogravimetry in a magnetic suspension balance (MSB) at 500 °C for 5 hours. The scanning electron microscopy (SEM), X-ray diffraction spectrometry (XRD) and Vickers Hardness measurement were used for sample characterization. The formation of ferro-nitride phase after implantation did not occur, however a thin layer considered to contain nitrogen interstitials was detected. The oxidation of both samples before and after implantation followed parabolic kinetics indicating inward growth of oxide scale characteristically due to diffusion of oxygen anions towards matrix surface. After oxidation test relativelly stable oxide scales were observed. Oxidation rates decreased proportionally with the increasing of implantation time due to the formation of oxide layer which is considered to be effectiv inhibitor for the oxygen diffusion.

36 MATERIALS SCIENCE↗

Oxidation Behavior Comparison of UAM and Conventional Zry-4

Initial hydrothermal corrosion and steam exposures have been completed on ultrasonic additive manufacturing (UAM) Zry4 specimens to compare to wrought Zry4 performance in both normal operation and accident conditions. Slightly higher mass gains were found for the UAM Zry4 specimens in both conditions, but these were generally associated with internal oxidation where delamination of build layers occurred in the UAM material. Further characterization is being completed to conclude this first phase of testing while a second phase is being planned.

36 MATERIALS SCIENCE↗

High Temperature Oxidation Behavior of Fe- and Ni-Based Alloy Foils in Water Vapor at 850 °C

Operating temperatures above 700°C are desired to improve the efficiency of power generation systems such as microturbines. Therefore, the use of creep-resistant Ni-based or Fe-based alloys, which can form protective Cr2O3 and Al2O3 scales, is required. In this paper, Fe- and Ni-based alloy foils were oxidized in air + 10 % H2O for up to 3,000 h at 850°C to identify the most promising alloys. The thickness and chemical composition of the spinel oxide formed on top of the Cr2O3 scale varied between S3100, N08120 and N06230 alloy foils. In addition, the rate of Cr and Mn loss (spinel and Cr2O3 oxidation and volatilization) or Al loss (oxidation) and the dissolution of strengthening precipitates, were found to be a function of the nature of the formed oxide (Fe or Ni-rich spinel, Cr2O3, Al2O3). Alloys N06230 and alumina-forming austenitic (AFA) steels were found to be well-suited for the applications as microturbine recuperator foil materials up to 850°C.

Romedenne, Marie↗

Oxidation Behavior of Ni-Based Alloys Fabricated by Additive Manufacturing

Additive manufacturing (AM) allows for the fabrication of complex near net shape components, leading to new design opportunities and significant savings, for example by decreasing tooling and materials cost or by accelerating prototype development. New Ni-based alloy heat exchangers with thin-walled areas exposed to hot gases will, however, suffer from corrosion degradation, and the high temperature oxidation performance of AM alloys needs to be addressed. Alloy N06002 (Ni-22Cr-18Fe-9Mo) fabricated by electron beam melting (EBM) and selective laser melting (SLM) along with EBM-fabricated N07247 and modified N07247 were cyclic oxidation tested at 950°C in air and humid air for durations ranging from 100 h to 5000 h. Increased spallation rates were observed initially for the AM N06002 alloys in comparison with wrought N06002 alloy because of the AM alloy specific microstructures. After ~2000 h, the situation was reversed with significant spallation observed for the wrought HX alloy only. Low mass gains were observed for the EBM N07247 alloys at 950°C, but thick oxide scales were observed locally due to the presence of oxidized cracks. Massive oxidation of these cracks led to fast oxidation rates at 1100°C.

Dryepondt, Sebastien N.↗

The effects of Cr, Co, Al, Mo and Ta on the cyclic oxidation behavior of a prototype cast Ni-base superalloy based on a 2(5) composite statistically designed experiment

A series of cast Ni-base superalloys were systematically varied at selected levels of Co, Cr, Mo, Ta, and Al. The elemental levels varied were Mo, 0 to 4 percent; Cr, 6 to 18 percent; Co, 0 to 20 percent, Ta, 0 to 8 percent; and Al, 3.25 to 6.25 percent. The cyclic oxidation resistance was determined from specific weight change data as a function of time for 1 hr cycles in static air at 1100 C. The significant terms in decreasing order of their importance were Al, Ta, Cr2, Al-Cr, Cr-Co, Co2, Al-Mo, Cr-Mo, Al-Al, and Mo-Ta. The Al term alone accounted for close to 82 percent of the explained variability. The estimating equation showed that the Al level was the most important and should be at its 6.25 wt % maximum value. The Mo and Ta levels should also be at their maximum 4 and 8 wt % respectively. The cobalt composition should be as low as possible, i.e., 0 wt%. The Cr level optimum varies depending on the other 4 levels. The X-ray diffaction results indicate the most protective scales are alumina/aluminate spinel stabilizized with a tri-rutile oxide high in Ta and Mo.

Barrett, C. A.↗

Cyclic Oxidation Behavior of CuCrAl Cold-Sprayed Coatings for Reusable Launch Vehicles

The next generation of reusable launch vehicles is likely to use GRCop-84 [Cu-8(at.%)Cr-4%Nb] copper alloy combustion liners. The application of protective coatings on GRCop-84 liners can minimize or eliminate many of the environmental problems experienced by uncoated liners and significantly extend their operational lives and lower operational cost. A newly developed Cu- 23 (wt.%) Cr-5% Al (CuCrAl) coating, shown to resist hydrogen attack and oxidation in an as-cast form, is currently being considered as a protective coating for GRCop-84. The coating was deposited on GRCop-84 substrates by the cold spray deposition technique, where the CuCrAl was procured as gas-atomized powders. Cyclic oxidation tests were conducted between 773 and 1,073 K to characterize the coated substrates.

Raj, Sai↗

Oxidation Behavior of Copper Alloy Candidates for Rocket Engine Applications (Technical Poster)

A rocket engine's combustion chamber is lined with material that is highly conductive to heat in order to dissipate the huge thermal load (evident in a white-hot exhaust plume). Because of its thermal conductivity copper is the best choice of liner material. However, the mechanical properties of pure copper are inadequate to withstand the high stresses, hence, copper alloys are needed in this application. But copper and its alloys are prone to oxidation and related damage, especially "blanching" (an oxidation-reduction mode of degradation). The space shuttle main engine combustion chamber is lined with a Cu-Ag-Zr alloy, "NARloy-Z", which exhibits blanching. A superior liner is being sought for the next generation of RLVs (Reusable Launch Vehicles) It should have improved mechanical properties and higher resistance to oxidation and blanching, but without substantial penalty in thermal conductivity. GRCop84, a Cu-8Cr-4Nb alloy (Cr2Nb in Cu matrix), developed by NASA Glenn Research Center (GRC) and Case Western Reserve University, is a prime contender for RLV liner material. In this study, the oxidation resistance of GRCop-84 and other related/candidate copper alloys are investigated and compared

Ogbuji, Linus U. J.↗

Mechanical and Thermal Oxidation Behavior of Poly(Lactic Acid)/Halloysite Nanotube Nanocomposites Containing N,N′-Ethylenebis(Stearamide) and SEBS-g-MA

Poly(lactic acid) (PLA)/halloysite nanotube (HNT) nanocomposites were prepared using melt compounding followed by compression molding. Maleic anhydride grafted styrene–ethylene/butylene–styrene copolymer (SEBS-g-MA) and N,N′-ethylenebis(stearamide) (EBS) were used to improve the impact properties of PLA nanocomposites. The properties of PLA/HNT nanocomposites were characterized by tensile and impact tests, Fourier transform infrared spectroscopy, thermal analysis (DSC and TGA), and morphological analysis (FESEM and TEM). In addition, the oxidation onset temperature (OOT) was determined using DSC. The PLA/HNT6/EBS5 nanocomposites gives higher impact strength improvement (98%) compared to that of PLA/HNT6/SEBS-g-MA5 (77%). Also, the PLA/HNT6/EBS5 exhibited higher OOT compared to that of PLA/HNT6/SEBS-g-MA5 nanocomposites.

36 MATERIALS SCIENCE↗

The oxidation behavior of Ni-Cr-Al-2ThO2 alloys at 1093 and 1204 C.

A pack diffusion process has been developed which permits the introduction of nearly 6 wt % Al into solid solution in the near surface region of TDNiCr (Ni-20 wt % Cr-2 vol % ThO2) and Ni-20Cr. Alumina scales, adherent under cyclic heating and cooling conditions, were produced on TDNiCr-5.86Al upon exposure to an environment of 1330 N/sq m (10 torr) or 101,000 N/sq m (760 torr) air at temperatures of 1093 and 1204 C. While the same oxidation kinetics were observed in isothermal tests for Ni-14.6Cr-5.86Al as were obtained for the TDNiCr-5.86Al, the dispersion-strengthened alloy exhibited superior oxide scale adhesion during cyclic testing. At 1204 C, continuous weight gains were observed under all test conditions for TDNiCr-5.86Al, in contrast to the weight loss with time which occurred several hours after exposure of TDNiCr to an oxidizing environment. TDNiCr with an initial aluminum surface concentration of 4.95 wt % has nearly comparable oxidation resistance to the TDNiCr-5.86Al alloy.

Seltzer, M. S.↗

The Ablation and Oxidation Behaviors of SiC Coatings on Graphite Prepared by Slurry Sintering and Pack Cementation

SiC coatings were generated on graphite using slurry sintering (SS) and pack cementation (PC). The samples’ ablation features were assessed by an oxyacetylene torch. The rates of mass ablation of the PC–SiC and SS–SiC coatings were approximated 2.17 × 10{sup −3} and 9.52 × 10{sup −3} g s{sup −1}, respectively, decreased by 84.1 and 29.6% compared to the uncoated samples. It was mainly attributed to the formation of a SiO{sub 2} layer on the surface. The continuous SiO{sub 2} molten film formed via the PC–SiC oxidation generates a sealing mechanism which can be an obstacle against the oxygen diffusion and hinder more ablation. This is while discontinuous SiO{sub 2} film formed from the thin SS–SiC cannot protect the graphite effectively. The non-isothermal oxidation test shows that without the SiC coating, the sample weight is lost largely from 25 to 1500 °C, and its weight loss was 2.2% after the TGA. However, after coating, the samples possessed excellent oxidation protection and weight losses of SS–SiC and PC–SiC coatings are down to 1.3 and 0.6%, respectively. The more oxidation of the graphite substrate occurred due to the formation of macrocracks in the coating during the TGA and also the formation of holes on SiO{sub 2} glass layer owing to release of CO or CO{sub 2}.

36 MATERIALS SCIENCE↗