Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OLSON”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Synergistic maximization of the carbohydrate output and lignin processability by combinatorial pretreatment

Lignocellulosic biorefineries have gained much attention worldwide as a potential solution to the challenges of energy demand and global climate change. However, the industrial implementation of biorefineries has been hindered by low fermentable sugar yields and low lignin processability. Combinatorial pretreatments with a low holding temperature were investigated in an effort to synergistically improve the carbohydrate output and lignin processability from corn stover. Upon combinatorial pretreatment with 1% H 2 SO 4 for 30 min followed by 1% NaOH for 60 min at 120 °C, glucan and xylan conversion increased by 11.2% and 8.3% respectively relative to single pretreatment. This combinational pretreatment removed the amorphous portion, disrupted the rigid structure, and increased the water holding capacity of corn stover, thus increasing the hydrolysis performance. With whole fractionation by combinatorial pretreatment, glucose and xylose yields were 88.4% and 72.6%, respectively, representing increases of 10.0% and 8.1%. The lignin yield was 19.7% in the solid residue and 77.6% in the liquid stream, which increased by 33.4%. When grown in fed-batch fermentation mode, a record level of polyhydroxyalkanoate (PHA) concentration (1.0 g l –1 ) was obtained using lignin as a carbon source by Pseudomonas putida KT2440. Lignin characterization results showed that combinatorial pretreatment increased the G- and H-lignin content, reduced the β–β and β-O-4 groups, and fractionated more aromatic monomers, thus facilitating lignin processability into PHA. Furthermore, these results highlighted the use of combinational pretreatment at a low holding temperature as a means to synergistically maximize the carbohydrate output and lignin processability, which provides a unique set of features to improve the biorefining performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Incipient microphase separation in short chain perfluoropolyether-block-poly(ethylene oxide) copolymers

Here, incipient microphase separation is observed by wide angle X-ray scattering (WAXS) in short chain multiblock copolymers consisting of perfluoropolyether (PFPE) and poly(ethylene oxide) (PEO) segments. Two PFPE–PEO block copolymers were studied; one with dihydroxyl end groups and one with dimethyl carbonate end groups. Despite having a low degree of polymerization (N ~ 10), these materials exhibited significant scattering intensity, due to disordered concentration fluctuations between their PFPE-rich and PEO-rich domains. The disordered scattering intensity was fit to a model based on a multicomponent random phase approximation to determine the value of the interaction parameter, χ, and the radius of gyration, R g . Over the temperature range 30–90 °C, the values of χ were determined to be very large (~2–2.5), indicating a high degree of immiscibility between the PFPE and PEO blocks. In PFPE–PEO, due to the large electron density contrast between the fluorinated and non-fluorinated block and the high value of χ, disordered scattering was detected at intermediate scattering angles, (q ~ 2 nm -1 ) for relatively small polymer chains. Finally, our ability to detect concentration fluctuations was enabled by both a relatively large value of χ and significant scattering contrast.

36 MATERIALS SCIENCE↗
DOE OSTI2012

X-ray conversion efficiency in vacuum hohlraum experiments at the National Ignition Facility

X-ray fluxes measured in the first 96 and 192 beam vacuum hohlraum experiments at the National Ignition Facility (NIF) were significantly higher than predicted by computational simulations employing XSN average atom atomic physics and highly flux-limited electron heat conduction. For agreement with experimental data, it was found that the coronal plasma emissivity must be simulated with a detailed configuration accounting model that accounts for x-ray emission involving all of the significant ionization states. It was also found that an electron heat conduction flux limit of f= 0.05 is too restrictive, and that a flux limit of f= 0.15 results in a much better match with the NIF vacuum hohlraum experimental data. The combination of increased plasma emissivity and increased electron heat conduction in this new high flux hohlraum model results in a reduction in coronal plasma energy and, hence, an explanation for the high ({approx}85%-90%) x-ray conversion efficiencies observed in the 235 < T{sub r} < 345 eV NIF vacuum hohlraum experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Alternative hot spot formation techniques using liquid deuterium-tritium layer inertial confinement fusion capsules

The baseline DT ice layer inertial confinement fusion (ICF) ignition capsule design requires a hot spot convergence ratio of ~34 with a hot spot that is formed from DT mass originally residing in a very thin layer at the inner DT ice surface. In the present paper, we propose alternative ICF capsule designs in which the hot spot is formed mostly or entirely from mass originating within a spherical volume of DT vapor. Simulations of the implosion and hot spot formation in two DT liquid layer ICF capsule concepts—the DT wetted hydrocarbon (CH) foam concept and the “fast formed liquid” (FFL) concept—are described and compared to simulations of standard DT ice layer capsules. 1D simulations are used to compare the drive requirements, the optimal shock timing, the radial dependence of hot spot specific energy gain, and the hot spot convergence ratio in low vapor pressure (DT ice) and high vapor pressure (DT liquid) capsules. 2D simulations are used to compare the relative sensitivities to low-mode x-ray flux asymmetries in the DT ice and DT liquid capsules. It is found that the overall thermonuclear yields predicted for DT liquid layer capsules are less than yields predicted for DT ice layer capsules in simulations using comparable capsule size and absorbed energy. However, the wetted foam and FFL designs allow for flexibility in hot spot convergence ratio through the adjustment of the initial cryogenic capsule temperature and, hence, DT vapor density, with a potentially improved robustness to low-mode x-ray flux asymmetry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2014

High-density carbon ablator experiments on the National Ignition Facility

High Density Carbon (HDC) is a leading candidate as an ablator material for Inertial Confinement Fusion (ICF) capsules in x-ray (indirect) drive implosions. HDC has a higher density (3.5 g/cc) than plastic (CH, 1 g/cc), which results in a thinner ablator with a larger inner radius for a given capsule scale. This leads to higher x-ray absorption and shorter laser pulses compared to equivalent CH designs. This paper will describe a series of experiments carried out to examine the feasibility of using HDC as an ablator using both gas filled hohlraums and lower density, near vacuum hohlraums. These experiments have shown that deuterium (DD) and deuterium-tritium gas filled HDC capsules driven by a hohlraum filled with 1.2 mg/cc He gas, produce neutron yields a factor of 2× higher than equivalent CH implosions, representing better than 50% Yield-over-Clean (YoC). In a near vacuum hohlraum (He = 0.03 mg/cc) with 98% laser-to-hohlraum coupling, such a DD gas-filled capsule performed near 1D expectations. A cryogenic layered implosion version was consistent with a fuel velocity = 410 ± 20 km/s with no observed ablator mixing into the hot spot.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2014

Investigation of ion kinetic effects in direct-drive exploding-pusher implosions at the NIF

Measurements of yield, ion temperature, areal density (ρR), shell convergence, and bang time have been obtained in shock-driven, D 2 and D 3 He gas-filled “exploding-pusher” inertial confinement fusion (ICF) implosions at the National Ignition Facility to assess the impact of ion kinetic effects. These measurements probed the shock convergence phase of ICF implosions, a critical stage in hot-spot ignition experiments. The data complement previous studies of kinetic effects in shock-driven implosions. Ion temperature and fuel ρR inferred from fusion-product spectroscopy are used to estimate the ion-ion mean free path in the gas. A trend of decreasing yields relative to the predictions of 2D draco hydrodynamics simulations with increasing Knudsen number (the ratio of ion-ion mean free path to minimum shell radius) suggests that ion kinetic effects are increasingly impacting the hot fuel region, in general agreement with previous results. Lastly, the long mean free path conditions giving rise to ion kinetic effects in the gas are often prevalent during the shock phase of both exploding pushers and ablatively driven implosions, including ignition-relevant implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

Direct minority carrier transport characterization of InAs/InAsSb superlattice nBn photodetectors

We present an extensive characterization of the minority carrier transport properties in an nBn mid-wave infrared detector incorporating a Ga-free InAs/InAsSb type-II superlattice as the absorbing region. Using a modified electron beam induced current technique in conjunction with time-resolved photoluminescence, we were able to determine several important transport parameters of the absorber region in the device, which uses a barrier layer to reduce dark current. For a device at liquid He temperatures we report a minority carrier diffusion length of 750 nm and a minority carrier lifetime of 202 ns, with a vertical diffusivity of 2.78 x 10 –2 cm 2 /s. We also report on the device's optical response characteristics at 78 K.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Temperature-dependent optical measurements of the dominant recombination mechanisms in InAs/InAsSb type-2 superlattices

Temperature-dependent measurements of carrier recombination rates using a time-resolved optical pump-probe technique are reported for mid-wave infrared InAs/InAs{sub 1−x}Sb{sub x} type-2 superlattices (T2SLs). By engineering the layer widths and alloy compositions, a 16 K band-gap of ∼235 ± 10 meV was achieved for five unintentionally and four intentionally doped T2SLs. Carrier lifetimes were determined by fitting lifetime models based on Shockley-Read-Hall (SRH), radiative, and Auger recombination processes to the temperature and excess carrier density dependent data. The minority carrier (MC), radiative, and Auger lifetimes were observed to generally increase with increasing antimony content and decreasing layer thickness for the unintentionally doped T2SLs. The MC lifetime is limited by SRH processes at temperatures below 200 K in the unintentionally doped T2SLs. The extracted SRH defect energy levels were found to be near mid-bandgap. Also, it is observed that the MC lifetime is limited by Auger recombination in the intentionally doped T2SLs with doping levels greater than n ∼ 10{sup 16} cm{sup −3}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Far infrared edge photoresponse and persistent edge transport in an inverted InAs/GaSb heterostructure

Direct current (DC) transport and far infrared photoresponse were studied an InAs/GaSb double quantum well with an inverted band structure. The DC transport depends systematically upon the DC bias configuration and operating temperature. Surprisingly, it reveals robust edge conduction despite prevalent bulk transport in our device of macroscopic size. Under 180 GHz far infrared illumination at oblique incidence, we measured a strong photovoltaic response. We conclude that quantum spin Hall edge transport produces the observed transverse photovoltages. Overall, our experimental results support a hypothesis that the photoresponse arises from direct coupling of the incident radiation field to edge states.

Dyer, G. C.↗
DOE OSTI2016

First beryllium capsule implosions on the National Ignition Facility

The first indirect drive implosion experiments using Beryllium (Be) capsules at the National Ignition Facility confirm the superior ablation properties and elucidate possible Be-ablator issues such as hohlraum filling by ablator material. Since the 1990s, Be has been the preferred Inertial Confinement Fusion (ICF) ablator because of its higher mass ablation rate compared to that of carbon-based ablators. This enables ICF target designs with higher implosion velocities at lower radiation temperatures and improved hydrodynamic stability through greater ablative stabilization. Recent experiments to demonstrate the viability of Be ablator target designs measured the backscattered laser energy, capsule implosion velocity, core implosion shape from self-emission, and in-flight capsule shape from backlit imaging. The laser backscatter is similar to that from comparable plastic (CH) targets under the same hohlraum conditions. Implosion velocity measurements from backlit streaked radiography show that laser energy coupling to the hohlraum wall is comparable to plastic ablators. The measured implosion shape indicates no significant reduction of laser energy from the inner laser cone beams reaching the hohlraum wall as compared with plastic and high-density carbon ablators. These results indicate that the high mass ablation rate for beryllium capsules does not significantly alter hohlraum energetics. In addition, these data, together with data for low fill-density hohlraum performance, indicate that laser power multipliers, required to reconcile simulations with experimental observations, are likely due to our limited understanding of the hohlraum rather than the capsule physics since similar multipliers are needed for both Be and CH capsules as seen in experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗