SEARCH · Engineering Papers

Results for “Neutron Leakage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Analyzing the thermionic reactor critical experiments

The Thermionic Reactor Critical Experiments (TRCE) consisted of fast spectrum highly enriched U-235 cores reflected by different thicknesses of beryllium or beryllium oxide with a transition zone of stainless steel between the core and reflector. The mixed fast-thermal spectrum at the core reflector interface region poses a difficult neutron transport calculation. Calculations of TRCE using ENDF/B fast spectrum data and GATHER library thermal spectrum data agreed within about 1 percent for the multiplication factor and within 6 to 8 percent for the power peaks. Use of GAM library fast spectrum data yielded larger deviations. The results were obtained from DOT R Theta calculations with leakage cross sections, by region and by group, extracted from DOT RZ calculations. Delineation of the power peaks required extraordinarily fine mesh size at the core reflector interface.

Niederauer, G. F.↗

DOE OSTI2022

First-collision source treatment for ray effect mitigation in discrete-ordinate radiation transport solutions

Deterministic transport codes play a fundamental role in the modelling and simulation of neutron transport. One of the most common deterministic methods is the method of discrete ordinates, also known as the S method. While offering significant advantages over other deterministic methods or stochastic methods like Monte Carlo, the method of discrete ordinates suffers from non-physical artifacts in its local solution due to its discretization of angle. These artifacts, referred to as ray effects because of their ray-like appearance, tend to be worse in problems with small sources in areas with little scattering. Significant effort has gone into developing methods to mitigate ray effects, such as the first-collision source treatment, which separates the angular flux into the uncollided and collided fluxes and solving them using non-traditional techniques such as ray tracing. One such code capable of doing this is Lawrence Livermore National Laboratory's deterministic transport code ARDRA. Current ray tracing methods typically trace to a set of points inside a zone to compute an overall flux. However, this approach has significant drawbacks, such as a low order of convergence and not being conservative. Therefore, a new method has been developed that traces instead to a set of points on each of a zone's surfaces and computing the currents, before using these to obtain the flux. A comparison between these two ray tracing methods showed significant advantages to the new surface method, including inherent conservation, a higher convergence rate, and an increase in calculable information like leakage. This work performed under the auspices of the U.S. Department of Energy by Lawrence Liver- more National Laboratory under Contract DE-AC52-07NA27344. (authors)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2023

Design and Fabrication of a Temperature-Controlled Fueled Molten Salt Capsule Irradiation Experiment

Idaho National Laboratory (INL) is developing a Molten salt Research Temperature-controlled Irradiation (MRTI) experimental capsule for the Neutron Radiography (NRAD) reactor. The experiment is envisaged to be versatile and able to host a variety of salt-wall material combinations. The first test is designed to contain actinide-bearing chloride salt, which previously has not been subjected to a neutron field. The main objectives of the experiment are to produce irradiated salt samples for Post Irradiation Examination (PIE), to evaluate salt behavior under irradiation, and to test in-situ sensors/instrumentation. The final design for the experiment completed in 2022, and fabrication of the experiment is underway. The salt is double encapsulated providing insulation and redundancy in the case of leakage. A gas-gap between the inner capsule and the outer container enables tuning of thermal conduction to the NRAD coolant by altering its thickness and its gas-mixture. An inert gas mixture ratio in the gas-gap ensures the configurations reached a targeted average salt temperature of 600oC, while avoiding salt freezing or exceeding material limits. A resistive heater placed within a thermowell and controls the temperature of the experiment (both when the reactor is on or off). The selected configurations can contain over 10 cm3 of fuel-bearing chloride salt, which is sufficient for the purposes of the post-irradiation examination (PIE) and provides sufficient volume for two submerged thermocouple probes to monitor salt temperature. The capsule wall material is Inconel 625, and weld qualifications for the assembly have been developed. A glove-box laser weld technique was refined as part of this process to ensure a leak-tight assembly for the salt-bearing assembly and reduce the risks of impurities permeating into the salt. This work was supported through the INL Laboratory Directed Research & Development (LDRD) Program under DOE Idaho Operations Office Contract DE-AC07-05ID14517.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

ENYGF 2023 - Design of Temperature-controlled Fuel-salt Irradiation Experiment

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

First-principles Studies of Tritium Species Formation on and Desorption from Surfaces of $γ- LiAlO_2$ Pellets with Related Secondary Phase

The $γ- LiAlO_2$ ceramics enriched with the $^6Li$ isotope are used in the form of annular pellets in tritium-producing burnable absorber rods (TPBARs). When irradiated in a pressurized water reactor (PWR), the $^6Li$ absorbs neutrons, simulating the nuclear characteristics of a burnable absorber rod, and produces tritium $(_{1}^{3}H, T)$. Once the $_{1}^{3}H$ is produced in the bulk of $γ- LiAlO_2$, it diffuses to its surface, forming different $_{1}^{3}H$ species (possibly $T, OT, T_2, or T_2O$). The $T_2O$ is expected to be generated from experiment, to avoid $_{1}^{3}H$ leakage. However, up to now, it is still not clear which $_{1}^{3}H$ species are formed on the $γ- LiAlO_2$ surface and travel to the getter. Besides, with the dramatic Li loss under irradiation, the secondary phase (possibly $LiAl_5O_8$) precipitates and participates into the $_{1}^{3}H$ diffusivity and $_{1}^{3}H$ species formation. Therefore, exploring $_{1}^{3}H$ species formation on and desorption from surfaces of $γ- LiAlO_2$ with related secondary phases becomes a very important task to provide a better understanding of $_{1}^{3}H$H species escaping from pellets.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Assessment and validation of NEAMS tools for high-fidelity multiphysics transient modeling of microreactors: Application of NEAMS codes to perform multiphysics modeling analyses of micro-reactor concepts

The NEAMS Multiphysics Applications team aims at providing assessment of code useability and functionality for microreactor design and analyses, together with demonstration of their capabilities to properly capture the steady-state and time-dependent behavior of different microreactor concepts. In FY-24, significant progress was achieved in improving multi-physics models of several microreactors systems: HP-MR, GC-MR and KRUSTY. These efforts focused on solving more complex multiphysics problems enabled by enhanced tools capability, verifying and validating results obtained, providing feedback to developers for suggested improvements, and sharing these models to facilitate user training. A series of new multiphysics transients were completed on the HP-MR (using Griffin/BISON/Sockeye) with core startup transient, control drum inadvertent rotation accident, and hydrogen leakage from hydride moderator (also including SWIFT). On the GC-MR, a new full-core model was developed and analyzed through a series of new multiphysics (Griffin/BISON/SAM) transients to simulate moderator leakage (also including SWIFT), flow blockage and coolant depressurization. Additional and updated TRISO failure analyses were completed on the HP-MR unit-cell and GC-MR assembly models leveraging improved TRISO modeling capabilities. The amount of SiC failure following accidental transients at end-of-life was null. However, GC-MR assembly TRISO analysis highlighted Pd penetration rate can be problematic and may require design changes on the studied microreactor concept. The neutronics discrepancies observed on the KRUSTY model in previous years were resolved using hybrid set of Monte Carlo/Deterministic cross-sections. The multiphysics (Griffin neutronics / BISON thermal-mechanics) 15₵ insertion transient simulation displayed good agreement when comparing with experimental data. Initial modeling of the 30 ₵ reactivity insertion also displays promising results. Such close agreement provides important validation data that can be leveraged by the NEAMS program and by microreactor vendors to support licensing of their technology. Finally, important experience was gathered with the NEAMS tools leading to several user feedback shared with tools developers, especially with regards to MOOSE mesh generator and Griffin. This project led to many publications demonstrating modeling capabilities, and to three models shared on the Virtual Test Bed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

IER-484 CED3b Report: AFRRI ER1 Dosimetry Characterization

This report presents the preliminary work for IER 484, the characterization of the leakage radia tion field from the TRIGA reactor at the Armed Forces Radiobiology Research Institute (AFRRI). The purpose of the dose characterization is to establish the reference dose needed to execute a NAD inter-comparison exercise. During the week of August 20th, a team from Lawrence Livermore National Laboratory (LLNL), Sandia National Laboratory (SNL), and Institut de Radioprotection et de Sûreté Nucléaire (IRSN) performed various measurements in AFRRI’s TRIGA ER1 (Exposure Room 1) with Passive Neutron Spectrometer (PNS) spheres and nuclear accident dosimeters (NADs) mounted on Bottle Manikin Absorption (BOMAB) phantoms (to simulate doses received by people) and additional NADs mounted on aluminum plates (to simulate doses in free air). Without Atomic Weapons Establishment (AWE), LLNL became responsible for measuring the neutron spectrum using PNS spheres. SNL is responsible for providing photon dose data. LLNL, SNL, and IRSN each deployed their own NADs, which will be compared to the reference dose measured. Final characterization of the dose field based on analyzed data will be presented in the CED4a report.

42 ENGINEERING↗

DOE OSTI2020

Charge collection and electrical characterization of neutron irradiated silicon pad detectors for the CMS High Granularity Calorimeter

The replacement of the existing endcap calorimeter in the Compact Muon Solenoid (CMS) detector for the high-luminosity LHC (HL-LHC), scheduled for 2027, will be a high granularity calorimeter. It will provide detailed position, energy, and timing information on electromagnetic and hadronic showers in the immense pileup of the HL-LHC. The High Granularity Calorimeter (HGCAL) will use 120-, 200-, and 300-$\mu\textrm{m}$ thick silicon (Si) pad sensors as the main active material and will sustain 1-MeV neutron equivalent fluences up to about $10^{16}~\textrm{n}_\textrm{eq}\textrm{cm}^{-2}$. In order to address the performance degradation of the Si detectors caused by the intense radiation environment, irradiation campaigns of test diode samples from 8-inch and 6-inch wafers were performed in two reactors. Characterization of the electrical and charge collection properties after irradiation involved both bulk polarities for the three sensor thicknesses. Since the Si sensors will be operated at -30 $^\circ$C to reduce increasing bulk leakage current with fluence, the charge collection investigation of 30 irradiated samples was carried out with the infrared-TCT setup at -30 $^\circ$C. TCAD simulation results at the lower fluences are in close agreement with the experimental results and provide predictions of sensor performance for the lower fluence regions not covered by the experimental study. All investigated sensors display 60$\%$ or higher charge collection efficiency at their respective highest lifetime fluences when operated at 800 V, and display above 90$\%$ at the lowest fluence, at 600 V. The collected charge close to the fluence of $10^{16}~\textrm{n}_\textrm{eq}\textrm{cm}^{-2}$ exceeds 1 fC at voltages beyond 800 V.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2025

Sensitivity study of hydrogen Soret transport in yttrium Hydride-Based nuclear fuel

Yttrium hydride is an excellent solid neutron moderator material for high temperature nuclear reactor applications due to its high hydrogen density and exceptional hydride stability at high temperatures. Despite these attractive characteristics, the details of how hydrogen behaves within yttrium hydride while temperature gradients exist are still not well understood. The evolution of the hydrogen composition profile resulting from a temperature gradient requires knowledge of hydrogen’s heat of transport, a critical parameter that has not yet been measured for this material. In this work, we perform hydride redistribution, hydrogen dissociation, and hydrogen leakage calculations while varying the Soret heat of transport of hydrogen in yttrium hydride to elucidate the sensitivity of hydride stability under temperature gradients to this parameter. This study analyzes hydride stability of a hypothetical uranium-yttrium hydride nuclear fuel design during operation of a high temperature liquid metal-cooled nuclear reactor. Assuming U-YH x could be fabricated in a physically stabilized manner, this fuel system can likely maintain hydride stability while operating at very high power densities and temperatures. We find that even though the hydrogen dissociation pressure in the gas gap does vary by several percent as the heat of transport temperature parameter is varied, the hydrogen content in the U-YH x fuel meat is relatively insensitive to this parameter over the course of a high burnup fuel cycle; this is due to yttrium hydride’s excellent hydrogen retention under the high temperature conditions considered here. Here, this suggests that hydride stability analyses are insensitive to the value of the Soret heat of transport in U-YH x under steady state liquid metal-cooled reactor conditions. However, the susceptibility to internal gas overpressurization-induced stress-rupture of the cladding during a high temperature transient is more sensitive to this parameter due to the non-linear dependence of hydrogen gas dissociation pressure vs. composition and temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Evaluation of radiation hardness of High-Voltage silicon vertical JFETs

In the future ATLAS Inner Tracker, each silicon strip module will be equipped with a switch able to separate the high voltage supply from the sensor in case the latter becomes faulty. The switch, placed in between the HV supply and the sensor, needs to sustain a high voltage in its OFF state, to offer a low resistance path for the sensor leakage current in the ON state, and be radiation hard up to 1.2 * 10 15 neq/cm 2 along with other requirements. While GaN JFETs have been selected as suitable rad-hard switch, a silicon vertical HV-JFET was developed by Brookhaven National Laboratory as an alternative option. Pre-irradiation results showed the functionality of the device and proved that the silicon HV-JFET satisfied the pre-irradiation requirements for the switch. To assess its suitability after irradiation, a few p-type HV-JFETs have been neutron irradiated at Jozef Stefan Institute (JSI, Ljubljana, Slovenia). Overall, this paper reports the static characterization of these irradiated devices and the TCAD numerical simulations used to get an insight of the physics governing the post-irradiation behaviour.

47 OTHER INSTRUMENTATION↗

DOE OSTI2020

Sandia National Laboratories FY20 Progress Report

The Energetic Neutrons campaign led by Sandia National Laboratories (SNL) had a successful year testing electronic devices and printed circuit boards (PCBs) under 14 MeV neutron irradiation at OMEGA. During FY20 the Energetic Neutrons campaign increased the number and complexity of experiments, continued collaborations with external organizations, and generated knowledge that supports SNL’s National Security mission. In FY20 the Energetic Neutrons campaign was executed by an early career team led by a new PI. The SNL team members were trained to take over new responsibilities during the shot day to increase the number and complexity of experiments in the campaigns. Also, in FY20 for the first time the Energetic Neutrons campaign had a graduate student contributing with pre and post-irradiation characterizations at SNL of the semiconductor devices irradiated at OMEGA. In FY20 SNL collaborated with the Air Force Nuclear Weapons Center (AFNWC) and supported experiments related to radiation effects in semiconductor devices. SNL also gave the opportunity to ride along to Los Alamos National Laboratory and multiple scientists from MIT and LLE. SNL continued using the last two generations of the Neutron Effects Diagnostics (NEDs) to field active and passive experiments but also redesigned the latest generation of the NEDs to accommodate larger components and improve the vacuum sealing as shown in figure 1a. The redesigned NEDs allowed SNL to perform active tests of a high voltage (HV) PCB for the first time at OMEGA; where signals before, during and after the irradiation were recorded. The HV PCB installed in one of the SNL NEDs is shown in figure 1b where a 3D-printed nosecone was used to check for mechanical and electrical interference. Passive irradiations of multiple components were followed up with leakage current, gain measurements and radiation-induced defect characterization.

42 ENGINEERING↗

DOE OSTI2022

MPACT Theory Manual (V.4.3)

This manual presents the theory underlying the three-dimensional (3D) whole-core, pin-resolved neutron transport calculation methodologies employed in the MPACT code. MPACT’s primary goal is to provide accurate sub-pin power distributions in a computationally efficient manner. To accomplish this, MPACT offers several different transport method options. The 2D/1D method, in which 3D problems are decomposed into an axial stack of radial “slices,” is currently the most commonly used. In this option, two-dimensional (2D) planar solutions are provided by the method of characteristics (MOC), and axial solutions are provided via one-dimensional (1D) approximate diffusion, or P3 solutions. The radial and axial solutions are coupled by (i) axial and radial transverse leakages, and (ii) a global 3D coarse mesh finite difference (CMFD) solve, which provides both acceleration and stability to the solution iteration scheme. The subsequent chapters of this manual present a range of topics, including MOC, CMFD, axial nodal transport solvers, 2D/1D, self-shielding, depletion, thermal-hydraulics, and transient methods. Development of the underlying theory of the 2D/1D method is presented, diagrams are included to highlight important algorithmic flow, and important concepts are discussed as appropriate. This manual is intended to be self-sufficient, but references to published articles and other materials are included for further reading. MPACT is a relatively new code, with new capabilities and many computational methods that did not exist until recently. This manual is an even newer document, with chapters written by several different code contributors working under time constraints. For these reasons, the manual is not yet complete and finalized. Future versions of this manual will address current deficiencies.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2021

Slow control and monitoring system at the JSNS 2

The Sterile Neutrino Search at the J-PARC Spallation Neutron Source (JSNS$^2$) experiment aims to search for sterile neutrino oscillations using a neutrino beam from muon decays at rest. The JSNS$^2$ detector contains 17 tons of 0.1$\%$ gadolinium (Gd) loaded liquid scintillator (LS) as a neutrino target. Detector construction was completed in the spring of 2020. A slow control and monitoring system (SCMS) was implemented for reliable control and quick monitoring of the detector operational status and environmental conditions. It issues an alarm if any of the monitored parameters exceed a preset acceptable range. The SCMS monitors the high voltage of the photomultiplier tubes, the LS level in the detector, possible LS overflow and leakage, the temperature and air pressure in the detector, the humidity of the experimental hall, and the LS flow rate during filling and extraction. An initial 10 days of data-taking with a neutrino beam was done following a successful commissioning of the detector and SCMS in 2020 June. In this paper, we present a description of the assembly and installation of the SCMS and its performance.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Evaluating the X2 initial core zero power physics tests with Serpent-Ants

The validation of the Ants nodal neutronics code for VVER applications is started by modelling the zero power physics tests for the initial core of the Khmelnitsky 2 nuclear power plant as described in the X2 benchmark using the Serpent-Ants two step neutronics calculation chain. The Ants prediction compare favorably against an earlier continuous energy Monte-Carlo reference solution as well as the measured data, except for discrepancies in the SCRAM worth between predicted and measured values. Similar discrepancies have been previously reported for VVER-1000 reactors, and the Ants predicted SCRAM worths match well with the Serpent results. Additionally, the assembly power distribution and axial power distribution predicted by Ants for the critical HZP state of the reactor are also compared to a reference Serpent solution with very good results. Lastly, an investigation into the effects of the few-group structure used in the nodal calculations and the use or lack of leakage correction for group constants on the results shows that the best accuracy is reached with seven or eight energy groups without leakage correction, although a reasonable accuracy can also be obtained with two or three energy groups using fundamental mode leakage correction. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2024

Irradiation Results of Commercial Neutron and Gamma Sensors at the Ohio State University Research Reactor

This report serves to present the evaluation results of commercial radiation detectors (SPNDs) with the potential to accomplish the data objectives—having sufficient gamma and fast neutron sensitivity—at temperatures near 650°C. The detectors chosen for evaluation are gamma ion chambers from Exosens (previously known as Photonis) models CRGA11 and CRGE32 and tantalum-based self-powered neutron detectors (Ta-SPND) from Mirion. The evaluation was performed in a series of heat irradiations from ambient to 850°C in the 9.5-inch dry tube furnace at the Ohio State University Research Reactor (OSURR). Ion chamber counting curves were measured to evaluate sensor operability at temperature. Detector sensitivity to reactor power and temperature were measured and presented in curve fit parameters. The curve fit equations were used to identify the suggested operational temperatures based on reactor power. Overall, it was evaluated that the CRGA11 was not significantly affected by temperatures up to 650°C and is operable—with higher temperature-contributed signals—up to 700°C. The CRGE32 was more affected by the high temperatures compared to the CRGA11. As a result of increasing temperature, the leakage current was a dominating factor. While the detector can operate up to 600°C and 700°C with lowered high voltage, it is not recommended unless a suitably strong gamma flux field is present. Finally, Ta SPND did not demonstrate good performance beyond 350°C due to the presence of an unknown phenomenon at changing temperatures. The study of the phenomenon is an active research topic outside the scope of this project.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS2017

Packaging Technology for Dielectric-Coating-Less Heavy Ion Radiation Testing of High-Voltage (HV) Electronic Parts

Testing high voltage (HV) electronic parts (greater than 300 V) for sudden event effects (SEE) caused by cosmic rays in the space environment, consisting of energetic heavy-ions, and neutron radiation in the upper atmosphere is a crucial step towards using these parts in spacecraft and aircraft. Due to the nature of cosmic radiation and neutrons, electronic parts are tested for SEE without any packaging and/or shielding over the top of the device. In the case of commercial HV parts, the top of the packaging is etched off and then a thin dielectric coating is placed over the part in order to avoid electrical arcing between the device surface and wire bonds and other components. Even though the effects of the thin dielectric layer on SEE testing can be accounted for, the dielectric layer significantly hinders post testing failure analysis. Replicating the test capability of state-of-the-art packaging while eliminating the need for post radiation test processing of the die surface (that obscures failure analysis) is the goal. To that end, a new packaging concept for HV parts has been developed that requires no dielectric coating over the part. Testing of prototype packages used with Schottky diodes (rated at 1200V) has shown no electrical arcing during testing and leakage currents during reverse bias testing are within the manufactures specifications.

High Voltage↗

DOE OSTI2022

MPEX High Heat Flux Plasma Dump Design, Manufacture, and Articles Test

Here, the Material Plasma Exposure eXperiment (MPEX) device is a steady-state linear plasma device currently in the final design phase at the Oak Ridge National Laboratory. This device will reach ion fluences up to 10 31 m -2 and will be used to expose neutron-irradiated materials to divertor-relevant plasmas and to study the effects of plasma-material interactions. These studies will elucidate the complex effects of plasmas with divertor candidate materials capable of withstanding high heat flux and high fluences for next-generation fusion devices. Bidirectional plasma will be generated using a high-power (200 kW) helicon source. Plasma will be confined by superconducting magnets. The last plasma-facing component on the upstream side of the MPEX device is the dump, which has been designed to intercept plasma and energetic particles. The dump will have a total heat load of 9.2 kW. A copper alloy (Glidcop AL-15) was selected for use in the water-cooled flange design because of its high thermal conductivity, its retaining strength at elevated temperatures, and its ability to be used in the high-temperature braze joints used in this application. Titanium-zirconium-molybdenum (TZM) tiles are brazed to the Glidcop AL-15 flange using high-temperature braze alloy. External water-cooling channels are used on the dump flange to prevent water leakage inside the vacuum space. This article discusses the details of the high heat flux dump design, including the computational fluid dynamics (CFD) and structural analyses performed to validate the design to meet the operational requirements of the MPEX device.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

CSEWG Meeting Minutes

Work has been done at LANL to validate various updated evaluations from ENDF/BVIII.1b0 including: Fe, Cu, Si, U, Pu. Continuous energy tables were processed with NJOY2016 and output to ACE files. For non-Pu legacy critical benchmarks, all calculations were within the experimental benchmark uncertainty, with some benchmarks having shown lower bias using ENDF/B-VIII.1b0. In HST systems, ENDF/B-VIII.0 shows reasonable results above the thermal leakage fraction. ENDF/B-VIII.0.1 is doing slightly worse than ENDF/B- VIII.0. b0.2 and it also includes a new 19 F evaluation, so more work is needed to examine its impact. 233 U thermal and intermediate bare and water-reflected benchmarks agree well with ENDF/B-VIII.0. From ENDF/B-VIII.0 to ENDF/B-VIII.0b0.1, HMF-007 C/E are increasing and the new 19 F evaluation is helping the HMF-007 cases containing Teflon which have historically had high C/E. The Pu legacy benchmark suite is within experimental uncertainty with the exception of THOR. The INDEN evaluation followed by LANL gave the lowest mean absolute bias, but it remains difficult to make a determination on which Pu evaluation is the best. INDEN performs slightly better for the JEZEBEL series, while the LANL Pu evaluation is better for THOR and flattop benchmarks. For the PMI benchmark series INDEN outperforms the LLNL evaluation. For the PST benchmark series ENDF/B-VIII.0 and LLNL Pu evaluations are better than the INDEN evaluation. C/E ratios for Jezebel and Godiva reaction rate ratios show all the Pu evaluations are very close to one another, making it again difficult to say which is best. When examining neutron reactor kinetics parameters, each Pu evaluation is once again very close. Each individual Pu evaluation seems to have advantages in their own applications.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗