Readout Characteristics of Integrated Monolithic InGaAs Active Pixel Sensor Array
A newly fabricated Monolithic InGaAs Active Pixel Image Sensor is presented, and its readout characteristics are described.
Readout↗
SEARCH · Engineering Papers
Results for “Monolithic”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Monolithic InGaAs JFET Active Pixel Tunable Image Sensor (MAPTIS)
A new Monolithic InGaAs Active Pixel Multispectral Image Sensor is described. This Infrared sensor will utilize high quality InGaAs grown by Molecular Beam Epitaxy on InP substrate for the fabrication of a high speed Junction Field Effect Transistor array.
hyper↗
A 155-GHz Monolithic Low Noise Amplifier
This paper presents the design,fabrication and performance of a three-stage 155-GHz monolithic low noise amplifier (LNA) using 0.1 mue pseudomorphic (PM) InAlAs/InGaAs/InP HEMT technology.
Monolithic↗
How Should Researchers Measure Perovskite-Based Monolithic Multijunction Solar Cells’ Performance? A Calibration Lab's Perspective
Perovskite multijunctions (PVSK MJs) have made remarkable progress with monolithic PVSK/PVSK tandems surpassing the efficiency of single-junction (1 J) PVSK cells and PVSK/Si cells reported to exceed the 30% efficiency mark. These efficiencies are reported at standard test conditions (STC), established by the photovoltaic (PV) community to facilitate comparison between devices and technologies. Herein, it is discussed why an accurate STC performance measurement for a MJ is more complicated than for a 1 J cell and the special aspects to be considered when measuring the current-voltage characteristics and the performance of PVSK-containing MJ cells are emphasized. It is discussed why a spectrally adjustable solar simulator is needed and the sequence of accurate performance measurement, namely measurement of the spectral response of each junction, adjustment of the spectrum, and appropriate protocols for measuring the power output of the device at STC, is presented. For all these, common errors and pitfalls that sometime lead to misleading interpretation of the results are presented, and the methods to evaluate the accuracy of the data when a spectrally adjustable solar simulator is not available are recommended. Finally, first step is taken toward recommending performance measurement approaches when high throughput is required as will eventually be in a production line.
14 SOLAR ENERGY↗
Photoluminescence Excitation Spectroscopy of Monolithic Perovskite/Silicon Tandem Solar Cells
The contributions of each subcell to the total photoluminescence (PL) spectrum of a monolithic perovskite/silicon tandem solar cell are distinguished using a variable wavelength excitation laser source. Here, in the results, a strong overlap of the PL spectrum is shown, originating from the sub‐bandgap region of the perovskite top cell with the emission from the silicon bottom cell, even with near‐infrared excitation wavelengths. Consequently, an excitation laser wavelength of at least 815 nm is required for a dominant PL signal from the silicon bottom cell, and a wavelength no longer than 750 nm is needed for a dominant PL signal from the perovskite top cell in the investigated tandem solar cell. Moreover, a shoulder in the sub‐bandgap emission of the perovskite top cell almost coincides with the PL response region of the silicon bottom cell, which can cause signal confusion in subcell characterization.
14 SOLAR ENERGY↗
Optimizing feed modulation for coupled methane and NO x conversion over Pd-Pt/Mn 0.5 Fe 2.5 O 4 /Al 2 O 3 monolith catalyst
Here the impacts of feed modulation (frequency, amplitude) and catalyst design (composition and architecture) parameters are reported for the conversion of methane and NO x over a dual-layer Pt+Pd/Al 2 O 3 + Mn 0.5 Fe 2.5 O 4 /Al 2 O 3 monolith. CH 4 and NO x conversion data show that the dual-layer catalyst outperforms single-layer samples having the same catalyst loadings, with and without spinel. Close proximity of the PGM and MFO functions in the mixed-layer catalyst lowers the CH 4 conversion at high temperature while separating the PGM and spinel layers with an intermediate Al 2 O 3 layer does not. Methane conversion enhancement is linked to its nonmonotonic dependence on O 2 . The performance gains are tied to a transient activity spike that occurs during the lean-to-rich feed transition when water is present in the feed. The transient spike is attributed to the removal of CO and H 2 products via reactions with stored O 2 in the spinel, eliminating inhibition of methane steam reforming.
03 NATURAL GAS↗
Coupled methane and NO x conversion on Pt + Pd/Al 2 O 3 monolith: Conversion enhancement through feed modulation and Mn 0.5 Fe 2.5 O 4 spinel addition
The performance of a dual-layer Pt-Pd/Al 2 O 3 washcoated monolith promoted by an Al 2 O 3 -supported Mn 0.5 Fe 2.5 O 4 spinel base layer was evaluated with the objective to develop a catalyst with a lower loading of Platinum group metal (PGM) for stoichiometric natural gas vehicle (NGV) emission control. Flow reactor results show that a combination of a lean/rich modulated feed and spinel addition gives enhanced methane and NO conversions compared to a steady-state feed having the same overall composition. Washcoated catalysts – PGM-only, spinel-only, PGM + spinel – were compared over a wide range of operating conditions. The results show a decrease in the methane conversion light-off temperature of up to 85 °C for an application-relevant feed (CH 4 + NO + H 2 + CO + O 2 + H 2 O + CO 2 ) while a moderate 40 °C decrease was observed for a simple feed (CH 4 + O 2 + H 2 O + CO 2 ). In the absence of spinel the modulation enhancement is negatively impacted at high methane conversion (> 80 %). The data show that the O 2 storage and release property of the spinel is needed to fully exploit the modulation enhancement. The mechanism responsible for the enhancement is linked to suppression of O 2 inhibition on the methane oxidation rate near the stoichiometric neutral point (λ = 1). Sufficiently fast cycling achieves a balance between a metallic and oxidic precious metal crystallites favorable for methane activation. The addition of spinel moves this balance closer to the λ = 1 feed, enabling a high oxidation efficiency with lower byproduct NH 3 selectivity. Enhancement in the NO conversion follows the methane conversion due to an easier NO reduction under the slightly rich of stoichiometric feed. Comparison of the PGM + spinel catalysts to PGM-only catalysts shows that the addition of spinel in combination with modulation can achieve the same activity with a lower PGM loading.
03 NATURAL GAS↗
Matrix-free subcell residual distribution for Bernstein finite elements: Monolithic limiting
This paper is focused on the aspects of limiting in residual distribution (RD) schemes for high-order finite element approximations to advection problems. Both continuous and discontinuous Galerkin methods are considered in this work. Discrete maximum principles are enforced using algebraic manipulations of element contributions to the global nonlinear system. The required modifications can be carried out without calculating the element matrices and assembling their global counterparts. The components of element vectors associated with the standard Galerkin discretization are manipulated directly using localized subcell weights to achieve optimal accuracy. Low-order nonlinear RD schemes of this kind were originally developed to calculate local extremum diminishing predictors for flux-corrected transport (FCT) algorithms. In the present paper, we incorporate limiters directly into the residual distribution procedure, which makes it applicable to stationary problems and leads to well-posed nonlinear discrete problems. To circumvent the second-order accuracy barrier, the correction factors of monolithic limiting approaches and FCT schemes are adjusted using smoothness sensors based on second derivatives. Finally, the convergence behavior of presented methods is illustrated by numerical studies for two-dimensional test problems.
97 MATHEMATICS AND COMPUTING↗
The complex structural and chemical nature of monolithic U-10Mo fuel and Zr barrier layer
Nanoscale microstructural characterization by advanced transmission electron microscopy techniques on a U-10Mo/Zr barrier layer monolithic fuel plate was performed to evaluate the microstructural evaluation after high burn-up. Gas bubble superlattice evolution, grain restructuring, and evolution of the Zr interaction layer is investigated through detailed electron microscopy characterization. The use of automated crystallographic orientation mapping to irradiated U-10Mo fuel highlights that the restructured ultra-fine grains are separated by high angle grain boundaries at a burn up of 4.42 × 10 21 fissions/cm 3 . Additionally, advanced chemical analysis and multi-variable statistical analysis shows spatial clustering of solid fission product precipitates. Finally, characterization of a newly observed porous nanocrystalline Zr region in the barrier layer is studied. Finally, this work provides insights into the grain subdivision and restructuring process while using advanced microscopy techniques to analyze fission products in neutron-irradiated U-10Mo fuel.
36 MATERIALS SCIENCE↗
Microstructure-process relationships in monolithic U-10Mo fuel foil single-pass rolling: A parametric simulation study
In this work, a previously validated coupling of Kinetic Monte Carlo (KMC) Potts Model and finite element method (FEM) simulations was implemented to investigate the effects of microstructural features in as-cast and homogenized monolithic U-10Mo foils on the emergent microstructure after rolling and reheating. Parameters that could potentially affect recrystallization behavior of the rolled U-10Mo foils were considered: grain size distribution, uranium carbide (UC) size distribution, UC volume fraction, spatial distribution of UC, and rolling reduction magnitude. Grain structure and the magnitude of rolling reduction have the strongest influence on recrystallization kinetics and the fabricated grain size distribution. The UC distribution had only a weak effect on the recrystallization kinetics and final microstructures. While particle-stimulated nucleation (PSN) occurred in simulation more frequently as grain size increased, its incidence did not appear to considerably affect the recrystallization kinetics or grain size distribution.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Early self-organization of fission gas bubble superlattice formation in neutron-irradiated monolithic U-10Mo fuels
Self-organization of defect superlattices in far-from-equilibrium systems presents a promising way to mitigate swelling concerns in nuclear materials. The gas bubble superlattice (GBS) is a highly ordered, three-dimensional complex defect structure that can retain fission gasses in Uranium-Molybdenum (U-Mo) fuels. Transmission electron microscopy (TEM) investigation of monolithic U-10Mo fuel irradiated to 1.15 × 10 21 fissions/cm 3 and 1.30 × 10 21 fissions/cm 3 revealed that early-stage ordering preferentially occurs at the grain boundaries (GB) and that the critical bubble size for complete ordering is ~3 nm. Once formed at the GB, the GBS extends towards the grain interior; however, the spread in distance from the GB varies likely depending on the type and strength of the GB sink. TEM results also showed a possible correlation between the growth and evolution of the intragranular disordered bubbles and large dislocation networks. The fission product distribution in and outside of the GBS was also investigated confirming the presence of xenon in the GBS, as well as other fission products including cesium, barium, lanthanum, and cerium.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Porosity, swelling, and composition evolution in high-burnup monolithic U-Mo fuel
The microstructural progression of very high-burnup (>8 × 10 21 fissions/cm 3 ) monolithic uranium-molybdenum (U-10wt.%Mo) was analyzed, providing crucial insights into the behavior of post-recrystallized nuclear fuel, where scant data exists. Three focused ion beam cuboids sourced from a fuel plate with varying local burnups of 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 were characterized. The porosity and composition of the samples were evaluated to characterize the evolution of the microstructure as a function of fission density and different locations on the fuel plate, while simultaneously isolating plate-specific parameters such as Zr diffusion barrier thickness, hot-isostatic-pressing conditions, enrichment, and reactor conditions. The porosity was segmented, and the three-dimensional distribution of the porosity was extrapolated from the two-dimensional segmentation. The composition was assessed and quantified using energy-dispersive X-ray spectroscopy areal mapping. The porosity fraction increased as a function of the burnup from 27.77±0.51, 35.12±1.54, and 37.71±0.44 % for 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 , respectively. When compared to literature, the porosity volume fraction plateaus at burnups greater than 6 × 10 21 fissions/cm 3 , while the pore size grows linearly as a function of fission density. The number of large pores increased in number density as a function of burnup, while the smallest pores (<0.3 µm) increased up to 9.05 × 10 21 fissions/cm 3 , followed by a decrease at 9.36 × 10 21 fissions/cm 3 . The delamination and cracking in the fuel plate propagated through an interconnected porosity sublayer identified ∼5 µm from the diffusion barrier. The local swelling of the specimens was within or near the prediction bounds of the Robinson-Williams model for local swelling. The fission products, strontium, barium, cerium, and cesium, precipitated into the pores, while neodymium accumulated adjacent to the pores. Furthermore, these findings have direct implications for the development of fuel performance codes and the accurate documentation of the microstructure evolution in high burnup U-Mo, thus enhancing the safety and efficiency of nuclear fuel usage.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
A critical review of the history of fabricating monolithic U-Mo fuel plates
The fabrication of monolithic uranium-molybdenum alloy fuels, specifically those developed for high-performance research and test reactors, began in the early 2000s. The primary fuel form consists of uranium alloyed with 10-wt% molybdenum in a thin foil coated with zirconium and encapsulated in aluminum-6061 cladding. Over the years, the process has evolved with different types of casting, heat treatments, rolling schedules, and cladding applications. This review examines the history of these fabrication processes and their impact on microstructure and fuel-swelling performance. Even though various fabrication methods were used, we found little correlation between fabrication variation and fuel swelling. This insensitive relationship between fabrication variation and fuel swelling is primarily due to inhomogeneous microstructures that formed during casting and grain refinement that occurred during rolling. We conclude that the fabrication processes we examined produced similar microstructures, indicating that the fuel microstructure is somewhat insensitive to the fabrication parameters evaluated. However, the relatively small amount of historic data, such as those for grain sizes, limited this analysis. More recently fabricated materials, such as those from ongoing irradiation experiment, Mini-Plate-1 and Mini-Plate-2, were also excluded from this analysis and are intended to be reviewed separately. The findings, that fuel microstructure is somewhat insensitive to the fabrication parameters, do not imply that any fabrication method is acceptable, given the uncertainties in data and fuel-swelling observations. For example, only arc melting and vacuum induction melting casting processes were previously explored in the historic fabrication efforts. In conclusion, the findings should not be extrapolated to other casting processes.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Minimizing thickness variation in monolithic U-10Mo fuel foil and Zr interlayer during hot rolling: A microstructure-based finite element method analysis
Low-enriched uranium alloyed with 10 wt. % molybdenum (U-10Mo) has been identified as a promising alternative to highly enriched uranium fuel for the United States’ high performance research reactors. The monolithic U-10Mo fuel plate consists of a metallic U-10Mo fuel foil with a 25 µm Zr interlayer and a relatively thick cladding of aluminum alloy 6061. The Zr interlayer is typically applied during the hot co-rolling process, and this process dictates the uniformity of the Zr interlayer. Thickness variation observed in the U-10Mo and Zr interlayer has been attributed to several sources: the initial grain size of the U-10Mo castings, can materials, rolling temperature, inhomogeneous molybdenum content, and porosity in the cast U-10Mo. This thickness variation limits the ability to meet the dimensional specification; thus, a better understanding of the factors causing the nonuniform thickness is needed. In this work, we used a novel, microstructure-based finite element method to model the hot rolling process to address these concerns. Grain microstructures in U-10Mo were tessellated and explicitly considered in the finite element model. Each grain was assigned a random material property to mimic the grain strength variations induced by different grain orientations. Simulations were performed using six steel can thicknesses, four grain sizes, and with or without a Zr interlayer to investigate the influences of those variables on the thickness nonuniformity. The simulation results showed that a thinner steel can and finer U-10Mo grain size reduce thickness variations in both the U-10Mo fuel foil and Zr interlayer. The direct findings from the simulations and analysis can be used to optimize the hot rolling schedule, reduce fabrication defects, and meet the dimensional specifications. The proposed microstructure-based finite element model can be also coupled with experimental microstructure characterization data, images, and models to simulate multi-pass hot rolling.
36 MATERIALS SCIENCE↗
Enhancing actuation control in monolithic liquid crystal elastomer films with dual heat and light responsiveness
This study presents a dual heat and light-responsive monolithic liquid crystal elastomers (LCEs) film designed to enhance actuation control. The LCE films were capable of various motion types, including curvature reversal, oscillation, and sustainable flipping. By incorporating an azobenzene compound, the films exhibited additional functionalities such as enhanced curvature reversal, accelerated oscillation, and the ability to lock continuous flipping motion upon light stimulation. Furthermore, by adjusting the aspect ratio (AR) of a single film, different thermal motion states were realized, demonstrating the flexibility of this approach. Observations using an NIR camera confirmed temperature fluctuations corresponding to thermal exchange, and the influence of UV light on motion regulation was quantitatively analyzed. In conclusion, the ability to regulate motion through dual stimuli paves the way for improved dynamic motion control and thermal management in advanced robotic applications.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Methane flux from transplanted soil monoliths depends on moisture, but not origin
Soils both produce and consume methane (CH 4 ), a potent greenhouse gas that contributes to climate change. In coastal forests, upland soils are shifting from being CH 4 sinks to sources as sea levels rise, increasingly flooding soils with little prior inundation history. Ecosystem CH 4 budgets are highly uncertain due in part to the difficulty in separating fluxes measured at the soil surface into individual production and consumption processes which are likely to have different responses to future environmental conditions. Here, we measured growing season CH 4 fluxes from soil monoliths transplanted four years prior along an inundation and salinity gradient to determine how changes in abiotic conditions control CH 4 flux rates. To parse net fluxes measured at the soil surface into their component gross rates, we paired field measurements with a stable isotope pool dilution incubation of surface soils. Throughout the growing season, net soil surface CH 4 flux was positively correlated with soil moisture (p < 0.01), with lowland-located soils tending towards CH 4 sources (mean 0.349 ± 1.11 mg CH 4 -C m -2 hr -1 , error is standard deviation) and upland-located soils tending towards CH 4 sinks (-0.003 ± 0.003 mg CH 4 -C m -2 hr -1 ). Transplanted soils’ fluxes were statistically identical to their native neighbors once microtopography-driven differences in soil moisture were controlled for. The pool dilution experiment revealed that production and consumption rates were similar in upland and lowland surface soils (2.82 ± 3.29 µmol CH 4 g -1 dry soil d -1 production, 3.47 ± 2.03 µmol CH 4 g -1 dry soil d -1 consumption), indicating the majority of production likely occurs at depth in lowland soils. Both gross and net fluxes from transplanted soils showed no effect of soil origin after four years, suggesting low resistance of CH 4 cycling to global change drivers. Our results indicate the strength of the coastal forest CH 4 sink is likely to decrease in proportion to sea-level rise.
59 BASIC BIOLOGICAL SCIENCES↗
Sputtered indium tin oxide as a recombination layer formed on the tunnel oxide/poly-Si passivating contact enabling the potential of efficient monolithic perovskite/Si tandem solar cells
We focus on utilizing sputtered indium tin oxide (ITO) as a recombination layer, having low junction damage to an n-type silicon solar cell with a front-side tunnel oxide passivating electron contact, thereby enabling the development of a high efficiency monolithic perovskite/Si tandem device. High transparency and low resistivity ITO films are deposited via low power DC magnetron sputtering at room temperature onto a front-side thin SiO x /n + poly-Si contact in a complete Cz n-Si cell with a back-side Al 2 O 3 /SiN x passivating boron-diffused p + -emitter on a random pyramid textured surface. We report the cell characteristics before and after ITO sputtering, and we find a cure at 250 °C in air is highly effective at mitigating any sputtering induced damage. Our ITO coated sample resulted in an implied open-circuit voltage (iV oc ) of 684.7 ± 11.3 mV with the total saturation current density of 49.2 ± 14.8 fA/cm 2 , an implied fill factor (iFF) of 81.9 ± 0.8%, and a contact resistivity in the range of 60 mΩ-cm 2 to 90 mΩ-cm 2 . After formation of a local Ag contact to the rear emitter and sputtered ITO film as the front-side contact without grid fingers, the pseudo-efficiency of 20.2 ± 0.5% was obtained with the V oc of 670.4 ± 7 mV and pseudo FF of 77.3 ± 1.3% under simulated one sun with the calculated short-circuit current density of 30.9 mA/cm 2 from the measured external quantum efficiency. Furthermore, our modelling result shows that efficiency exceeding 25% under one sun is practically achievable in perovskite/Si tandem configuration using the ITO recombination layer connecting a perovskite top cell and a poly-Si bottom cell.
14 SOLAR ENERGY↗
A Monolithic Artificial Leaf for Solar Methanol Production from CO 2 and H 2 O
Methanol, an important liquid fuel and chemical feedstock, has yet to be produced using solar energy, H 2 O, and CO 2 as sole inputs in a standalone device. Here, this study directly addresses this longstanding challenge through presenting the first demonstration of unbiased solar methanol production from CO 2 and H 2 O with a monolithic artificial leaf design, surpassing the previous best energy efficiency in solar alcohol production by at least 1 order of magnitude. We first develop a new generation of photocathodes based on Si micropillar arrays and a cobalt tetraaminophthalocyanine molecular catalyst. By integrating a C 60 interlayer that facilitates unidirectional electron transfer through the semiconductor/catalyst interface, we realize a photovoltage of 500 mV, one of the highest recorded for single-junction Si-based photoelectrodes in aqueous CO 2 reduction, as well as unprecedented methanol formation with a Faradaic efficiency of 30% and a partial current density of 6.3 mA cm –2 . We further integrate the photocathode with a multijunction perovskite photovoltaic minimodule to afford a standalone solar fuel system, which demonstrates a light-to-methanol conversion efficiency of 0.8%, 32 times higher than the present record in light-to-alcohol conversion with an artificial leaf.
alcohols↗